LQSFP+PC-XX(QSFP+ Direct Attach Passive Copper Cable)

TELECOM / DATACOM SYSTEMS
Lightem LQSFP+PC-XX series
QSFP+ Direct Attach Passive Copper Cable
The QSFP+ passive cable assemblies are high performance,cost effective I/O solutions for 40G LAN, HPC and SAN applications. The QSFP+
passive copper cables are compliant with SFF-8436, QSFP+MSA and IEEE P802.3ba 40GBASE-CR4. It is offer a low power consumption,short
reach interconnect applications. The cable each lane is capable of transmitting data at rates up to 10Gb/s, providing an aggregated rate
of 40Gb/s.
Features
QSFP+ conforms to the Small Form Factor SFF-8436
4-Channel Full-Duplex Passive Copper Cable Transceiver
Support for multi-gigabit data rates :1 Gb/s - 10 Gb/s (per channel)
Maximum aggregate data rate: 40 Gb/s (4 x 10Gb/s)
Copper link length up to 5m (passive limiting)
High-Density QSFP 38-PIN Connector
Power Supply :+3.3V
Low power consumption: 0.02 W (typ.)
I2C based two-wire serial interface for
EEPROM signature which can be customized
Temperature Range: 0~ 70 °C
Applications
10 Gigabit Ethernet
40 Gigabit Ethernet
InfiniBand4x SDR, DDR, QDR
2, 4, 8, 10 Gigabit Fiber Channel
Fiber Channel over Ethernet
SAS,Servers,Hubs,Switches,Routers
Standards Compliance
IEEE 802.3ba
SFF-8436
InfiniBand
QSFP+ MSA
RoHS Compliant
TELECOM / DATACOM SYSTEMS
Recommended Operating Conditions
Parameter
Symbol
Min
Typical
Max
Unit
-40
+85
°C
Operating Case Temperature
Tc
0
+70
°C
Power Supply Voltage
VCC3
3.14
3.47
V
Power Dissipation
PD
0.02
W
Storage Ambient Temperature
Mechanical Dimensions
3.3
TELECOM / DATACOM SYSTEMS
QSFP+ Host Board Schematic for passive copper cables
Pin Descriptions
TELECOM / DATACOM SYSTEMS
Pin
Logic
1
Symbol
Name/Description
Notes
1
GND
Ground
2
CML-I
Tx2n
Transmitter Inverted Data Input
3
CML-I
Tx2p
Transmitter Non-Inverted Data Input
4
GND
Ground
5
CML-I
Tx4n
Transmitter Inverted Data Input
6
CML-I
Tx4p
Transmitter Non-Inverted Data Input
GND
Ground
7
1
1
8
LVTTL-I
ModSelL
Module Select
9
LVTTL-I
ResetL
Module Reset
Vcc Rx
+3.3V Power Supply Receiver
10
11
LVCMOSI/O
SCL
2-wire serial interface clock
12
LVCMOSI/O
SDA
2-wire serial interface data
GND
Ground
13
1
14
CML-O
Rx3p
Receiver Non-Inverted Data Output
15
CML-O
Rx3n
Receiver Inverted Data Output
16
2
GND
Ground
17
CML-O
Rx1p
Receiver Non-Inverted Data Output
18
CML-O
Rx1n
Receiver Inverted Data Output
19
GND
Ground
1
20
GND
Ground
1
1
21
CML-O
Rx2n
Receiver Inverted Data Output
22
CML-O
Rx2p
Receiver Non-Inverted Data Output
GND
Ground
23
1
24
CML-O
Rx4n
Receiver Inverted Data Output
25
CML-O
Rx4p
Receiver Non-Inverted Data Output
26
GND
Ground
27
LVTTL-O
ModPrsL
Module Present
28
LVTTL-O
IntL
Interrupt
29
Vcc Tx
+3.3V Power supply transmitter
2
30
Vcc1
+3.3V Power supply
2
LPMode
Low Power Mode
GND
Ground
31
LVTTL-I
32
1
1
33
CML-I
Tx3p
Transmitter Non-Inverted Data Input
34
CML-I
Tx3n
Transmitter Inverted Data Input
GND
Ground
35
1
36
CML-I
Tx1p
Transmitter Non-Inverted Data Input
37
CML-I
Tx1n
Transmitter Inverted Data Input
GND
Ground
38
1
Note 1: GND is the symbol for signal and supply (power) common for the QSFP+ module. All are common within the QSFP+ module and all
module voltages are referenced to this potential unless otherwise noted. Connect these directly to the host board signal-common ground plane.
Note 2: Vcc Rx, Vcc1 and Vcc Tx are the receiver and transmitter power supplies and shall be applied concurrently. Requirements defined
for the host side of the Host Edge Card Connector are listed in Table 6. Recommended host board power supply filtering is shown in Figure
4. Vcc Rx Vcc1 and Vcc Tx may be internally connected within the QSFP+ Module module in any combination. The connector pins are
each rated for a maximum current of 500 mA.
Ordering Information
PN: LQSFP+PC-XX
X1:1m/30AWG
X2:2m/30AWG
X3:3m/30AWG
X4:4m/26AWG
X5:5m/26AWG