Day/Night Camera - DWG Distribution

Day/Night Camera
Manual
(EV-1026-N3SQ shown)
1 ”
/3
Sony Super HAD II CCD  IR Day/Night  Weatherproof
IR LEDs for Nighttime Use  Up to 50ft (15m) Range
Model
Number
Lens
Size
Viewing
Angle
# of
IR LEDs
2.9mm
3.6mm
6.0mm
120°
92°
53°
12
24
24
2.9mm
3.6mm
6.0mm
120°
92°
53°
12
24
24
420 TV Lines
EV-1026-N2SQ
EV-1026-N3SQ
EV-1026-N6SQ
540 TV Lines
EV-1606-N2SQ
EV-1606-N3SQ
EV-1606-N6SQ
SECO-LARM
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.
ENFORCER Day/Night Camera
Specifications
1026-N2SQ
Type
CCD
Resolution
1026-N3SQ
1026-N6SQ
1606-N2SQ
1606-N3SQ
1606-N6SQ
IR bullet camera
/3” Sony Super HAD II
1
Pickup elements
Sync
420 TV lines
540 TV lines
510x492 pixels
768x494 pixels
Internal
Video output
1.0Vp-p composite video, 75Ω
Video output format
Lens
Viewing angle
NTSC*
2.9mm
3.6mm
6.0mm
2.9mm
3.6mm
6.0mm
120°
92°
53°
120°
92°
53°
0.05-lux (with LEDs off)
0-lux (with LEDs on)
Minimum illumination
Gamma correction
S/N ratio
Shutter control
Gain control
IP rating
# of infrared LEDs
0.02-lux (with LEDs off)
0-lux (with LEDs on)
0.45
>48dB
Auto Electric Shutter (AES)
Auto
LED range
Operating voltage
LEDs OFF
Current
draw
LEDs ON
Operating
temperature
Dimensions
Weight
12 (850nm)
Up to 40ft
(12m)
24 (850nm)
Up to 50ft
(15m)
150mA
75mA
250mA
IP66
24 (850nm)
12 (850nm)
Up to 50ft
Up to 40ft
(15m)
(12m)
12VDC ±10%
250mA
170mA
24 (850nm)
Up to 50ft
(15m)
24 (850nm)
Up to 50ft
(15m)
95mA
270mA
270mA
-4°~122° F (-20°~50° C)
311/16”x25/16”x2” (94x59x50 mm) with sunshield
10-oz (280g)
*PAL versions also available.
Parts List:
1 x Manual
1 x IR camera
1 x Sunshield
3 x Mounting bracket
3 x Mounting screws
3 x Screw anchors
1 x DC plug with
terminal block
Dimensions:
311/16” (94mm)
13/8”
(35mm)
2”
(50mm)
5/8”
(15mm)
13/4” (44mm)
25/16” (59mm)
213/16” (72mm)
(EV-1026-N3SQ shown)
2
SECO-LARM U.S.A., Inc.
ENFORCER Day/Night Camera
Overview:
A. Camera
B. Adjustable sunshield
C. Mounting bracket
D. 36” (0.9m) cord
E. Thumb screw
F. DC jack
I. Female BNC
connector
(video out)
B
G. Adjustment nut
H. DC plug with
terminal block
G
Connect to video
cable’s male
BNC connector
Important:
Do not remove label or
open case as warranty
will be voided.
D
A
F
F
H
G
E
C
I
Important:
Do not cut DC jack (F) or
female BNC connector (G)
as warranty will be voided.
(EV-1026-N3SQ shown)
Before Starting:
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electricity limits.
3. Do not aim the LED light directly at the eyes when the
LEDs are on.
4. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.
5. Do not mount the camera in areas exposed to radiation,
strong magnetic fields, or strong electrical signals.*
6. Do not open or disassemble the camera. There are no
field serviceable parts inside.
7. Do not drop the camera or subject it to strong vibrations.
*Note: Many video monitors produce strong
electromagnetic fields close to the display CRT,
especially when the monitor is turned on or during
de-gaussing, which occurs automatically with
many monitors when the monitor is turned on.
Installation:
1. Run a 12VDC power-supply wire and a video cable
with a male BNC connector through the wall to where
the camera is to be mounted (if necessary).
2. Assemble the mounting bracket; then screw it into the
back of the camera. Tighten the adjustment nut.
3. Temporarily connect the camera to the 12VDC power
supply. Do not cut DC jack or female BNC
connector as warranty will be voided. If needed,
use the included SECO-LARM DC plug with
terminal block.
4. Temporarily connect the camera’s female BNC
connector to the video cable’s male BNC connector.
5. While watching the monitor, hold the camera bracket
by hand against the wall where it is to be mounted,
then twist the camera until it is certain that this
SECO-LARM U.S.A., Inc.
mounting location is correct. Use a pencil to mark the
location of the three screw holes in the bracket.
6. Disconnect the 12VDC power supply and video cable.
7. Mount the bracket to the wall using the three included
mounting screws. If the wall is made of drywall, brick, or
similar material, it may be necessary to use the three
included screw anchors.
8. Reconnect the 12VDC power supply and video cable.
Turn the monitor on and make sure the camera is sending
the proper video signal.
9. To adjust the camera angle, loosen and tighten the
bracket’s thumb screw. Turn the camera and change its
angle relative to the bracket until the desired scene is
displayed.
10. Do a final test of the video camera and monitor.
3
ENFORCER Day/Night Camera
Troubleshooting
The screen is blank.




Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
The screen image is dim.
 Clean the lens using a soft, clean cloth.
 Check that the light source is adequate.
The screen image has poor contrast.
 Adjust the monitor’s contrast knob.
 Change the position of the camera.
The screen image flickers.
 Change the position of the camera.
The screen image is distorted.
 Change the position of the camera.
The camera case is hot.
 Check that the correct power supply is in use.
IR LEDs do not turn on.
 Check that the correct power supply is in use.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no field serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service
for a period of three (3) years from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy
is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications
without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326 E-mail: sales@seco-larm.com
4
PICSN4
MiEV-1026_EV-1606_1111.docx
Made in China
SECO-LARM U.S.A., Inc.