Protege DIN Rail Module Network Repeater

PRT-MNR2-DIN
Protege DIN Rail Module
Network Repeater
The Protege DIN Rail Module Network repeater is designed to
extend the network capabilities of the Protege system, an
advanced technology security product providing seamless and
powerful integration of access, security and building automation.
The module network repeater is added to the system via the
RS-485 or Ethernet and provides optical isolation between up to
three branches of the module network, easing power
requirements.
Feature Highlights
Ethernet Expansion
> 3 isolated RS-485 connections
The Ethernet solution enables the module network repeater to communicate via UDP
through a switch or router. You can connect the network repeater via Ethernet to:
> Internal industry standard 10/100
Ethernet
>
>
>
>
> Encrypted module network using RS-485
communication
Link module networks running between two buildings (within a close proximity)
Remove the need to run expensive cabling over long networks
Enable the network to reach physical locations where traditional wiring is difficult
Resolve issues with networks that are experiencing connectivity / communication issues
caused by ground loops or long distance runs
> RS-485 or Ethernet network expansion
POWER
STATUS
FAULT
> Designed for use with industry standard
DIN Rail mounting
D1/ D0/
BZ L1 NB NA Z8 V- Z7 Z6 V- Z5 V- V+
READER 2
ZONE INPUT 5-8
Expander
Keypad
Expander
Keypad
D1/ D0/
BZ L1 NB NA Z4 V- Z3 Z2 V- Z1 V- V+
12VDC OUT
READER 1
ZONE INPUT 1-4
12VDC OUT
PRT-CTRL-DIN
POWER
POWER
STATUS
STATUS
FAULT
FAULT
ETHERNET
1
2
5
6
> Configurable RS-485 biasing
3
4
POWER
POWER
STATUS
STATUS
FAULT
FAULT
RELAY 1
R1
ZONE
READER
BELL
MODEM
R2
N+ N- NA NB
B+ B- NOCOM NC NO COMNC
RS485 NETWORK
12VDC IN
Expander
BELL
RELAY 1
7
8
RELAY 2
Switch / Router
T1i R1i T1o R1o
RELAY 2
MODEM
ETHERNET 1
Network Expander
Controller
Main RS-485 Module Network
POWER
POWER
STATUS
STATUS
FAULT
FAULT
Expander
Expander
Isolated RS-485 Networks
RS-485 Expansion
You can place the network repeater virtually anywhere on the RS-485 module network to:
> Extend the RS-485 module network. While the maximum length of the RS-485 module
network is 900m (3000ft), the module network repeater enables you to extend it beyond this by
repeating the signals sent
> Create isolated RS-485 networks for keypads or devices located outside or in publicly
accessible areas
POWER
STATUS
FAULT
Keypad
D1/ D0/
BZ L1 NB NA Z8 V- Z7 Z6 V- Z5 V- V+
READER 2
ZONE INPUT 5-8
12VDC OUT
Expander
D1/ D0/
BZ L1 NB NA Z4 V- Z3 Z2 V- Z1 V- V+
READER 1
ZONE INPUT 1-4
12VDC OUT
PRT-CTRL-DIN
POWER
POWER
STATUS
STATUS
FAULT
FAULT
ETHERNET
1
2
5
6
Expander
4
RS485 NETWORK
R2
BELL
RELAY 1
RELAY 2
8
STATUS
STATUS
FAULT
FAULT
FAULT
T1i R1i T1o R1o
MODEM
ETHERNET 1
Controller
Main RS-485 Network
www.ict.co
POWER
POWER
STATUS
7
RELAY 2
B+ B- NOCOM NC NO COMNC
POWER
ZONE
BELL
N+ N- NA NB
12VDC IN
3
RELAY 1
R1
READER
MODEM
Expander
Network Expander
Keypad
Isolated RS-485 Networks
Expander
Isolated RS-485 Network Spurs
Configurable RS-485 Biasing
Web Interface
The RS-485 ports can be used to extend the
network into up to three optically isolated
branches. This enables the creation of
isolated RS-485 networks for keypads or
devices located outside or in publicly
accessible areas or for replacing existing
systems using spur wiring.
RS-485 biasing on the COM ports enable
you to set master or slave configuration for
each port. This allows for more reliable
communication between the network
repeater and the connected modules.
The web interface enables you to configure
and manage the module network repeater's
settings. The web interface also allows you
to monitor the status of the network repeater
and view the version information.
Technical Specifications
Power Supply
Operating Voltage
12V DC
Operating Current
65mA (typical)
Communication
RS-485
3 isolated RS-485 communication interface ports
Ethernet
1 10/100Mbps Ethernet Communication Link
Ports
Port 80 TCP/IP HTTP (Web Interface) Fixed
Port 9450 UDP/IP (MNR2 to Controller)
Dimensions
Dimensions (L x W x H)
78 x 90 x 60mm (3.07 x 3.54 x 2.36")
Weight
240g
Temperature
Operating
0˚-49˚C (32˚ - 122˚F)
Humidity
0%-93% non condensing, indoor use only (relative humidity)
Storage
-10˚- 85˚C (14˚ - 185˚F)
Disclaimer: Whilst every effort has been made to ensure accuracy in the representation of this product, neither Integrated Control Technology Ltd nor its
employees, shall be liable under any circumstances to any party in respect of decisions or actions they may make as a result of using this information. In
accordance with the Integrated Control Technology policy of enhanced development, design and specifications are subject to change without notice.
www.ict.co