Wireless Remote Control

Wireless Remote Control
LED SIGNATURE LIGHT
A. RETURN ALL SECTIONS
TO THE FLAT POSITION
B. RAISE (+) / LOWER (-)
HEAD SECTION OF THE BASE
C. RAISE (+) / LOWER (-)
FOOT SECTION OF THE BASE
D. ZERO GRAVITY
E. PROGRAM UP TO 2
MEMORY POSITIONS
F. ANTI SNORE
G. STOP ALL MASSAGE FEATURES
H. INCREASE (+) / REDUCE (-)
MASSAGE INTENSITY ON
HEAD SECTION OF THE BASE
I. ALTERNATES BETWEEN
MASSAGE WAVE SPEEDS
1, 2 and 3
J. INCREASE (+) / REDUCE (-)
MASSAGE INTENSITY ON
FOOT SECTION OF THE BASE
K. SELECT 1 OF 3 MASSAGE
WAVE SPEEDS
CUSTOMER SERVICE: 800-695-2540
12
Remote Control Operation Guide
• Slowly increases or decreases massage
intensity.
To increase massage intensity, press
(+) button.
To decrease massage intensity, press
(-) button.
HEAD AND FOOT ADJUSTMENT (B, C)
• Adjusts the head and foot sections to the
desired positions.
BED “FLAT” BUTTON (A)
• Levels the bed to the flat position when the button
is pressed and held for at least 1 second.
NOTE: The “FLAT” cycle can be interrupted
and cancelled by pressing the head or foot
adjustment buttons (B, C).
NOTE: The lowest setting will turn off the
corresponding massage unit.
ZERO GRAVITY (D)
• Allows your legs to be lifted to a position slightly
above the chest, which enables blood flow to
easily circulate back to the heart, thus reducing
stress and fatigue.
WAVE MASSAGE MODE (K)
• Turns on both head and foot massage
motors to one of the 3 wave functions.
NOTE: You must stop the massage before
you can switch to another wave function
or to the full body massage.
ANTI SNORE (F)
• Raises the HEAD to an upright position for
anti-snore.
MASSAGE STOP BUTTON (G)
• Press for 2 seconds to stop all massage
features.
PROGRAMMABLE MEMORY BUTTONS (E)
You can store 2 personalized memory positions
• To Set a Memory Position: When in desired
position, press and hold Memory button for
more than 5 seconds until the LED light flashes
3 times to signal Memory position is stored.
NOTE: The massage feature is designed
to automatically shut off after 30 minutes
of continuous use.
• To Recall a Memory Position: Press Memory
button 1 or 2 until LED lights up.
FULL BODY MASSAGE FUNCTION (I)
• Turns on both head and foot massage motors
and alternates between Wave Modes 1, 2 and 3.
NOTE: Do not hold the Memory button for
more than 5 seconds otherwise a new
memory position will be set.
ATTENTION: If the massage motors are
operating and Head and Foot lift or Memory
buttons are pressed, the massage motor will
stop and resume operating after lift position
reached. But if Flat button is pressed, the
massage motors will not resume after flat
position reached.
HEAD AND FOOT MASSAGE CONTROLS
(H, J)
• Turns on the corresponding massage unit
(starting at intensity 5 of 10)
CUSTOMER SERVICE: 800-695-2540
13
Remote Control Operation Guide
Additional Remote Features:
Notice:
• The Motion SELECT foundation uses a RF
(Radio Frequency) remote control system.
The changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
NOTE: This bed may have minor intermittent
performance due to RF Interference.
This is a normal operation of the bed and is
not a defect.
Important Note
• To comply with the FCC RF exposure
compliance requirements, no change to the
antenna or the device is permitted. Any change
to the antenna or the device could result in the
device exceeding the RF exposure requirements
and void user’s authority to operate the device.
• The buttons are backlit, when a button is
pressed,to aid in the visibility of the remote in
low light environments.
• Customers can control the remote without facing
the receiver (best transmission range is within 9
feet or 3 meters).
Safety:
THIS DEVICE COMPLIES WITH
PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE
(2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED
OPERATION.
• If there is an overload weight condition on the
head or foot mechanism, the control unit will
automatically stop all functions.
NOTE: Once the excess weight is removed,
the control unit will automatically start all
functions after 30 seconds.
• If the massage motors are continuously used for
a 30 minute period, the motors will automatically
shut down.
• The input transformer voltage is AC 120V 60 HZ,
the output voltage is DC 24V 3A. When there is
a short circuit, a fuse on the transformer will be
blown in order to protect the electrical equipment
(Fuse: 1.5A).
ATTENTION: When the above situation
occurs, the customer MUST seek professional
assistance.
CUSTOMER SERVICE:800-695-2540
14
Replacement Remote Control Programming
STEP 4
Note: The remote that comes with the
When the Green LED signature light illuminates,
the RF frequency code setting function will be
activated.
bed is already paired with your bed. No
further action is required. Only replacement
remote controls require user programming.
STEP
STEP 55
STEP 1
Place batteries into the remote control
(3 x AAA batteries).
Press any button on the remote control.
STEP 6
When the receiver light flashes, you have
completed the learning process of the RF
frequency code
STEP 2
Ensure the bed is plugged into a functioning
outlet.
STEP 3
Figure 2: A flashing Green LED indicates the
control box has received the remote control
signal.
Press the learn button for 3 seconds.
PAIRING INSTRUCTIONS
FOR JOINING 2 FOUNDATIONS
1 Wireless Remote Control and
2 Motion SELECT adjustable
foundations
Follow the directions for the 1 hand remote
control and 1 adjustable foundation.
Once Step 1 is complete, repeat the
directions for the 2nd adjustable foundation
using the same hand control.
Figure 1: Press “Learn Button” to initiate
the RF learning Mode.
NOTE: If a new signal is not received, it will
reset itself to normal mode in 10 seconds.
CUSTOMER SERVICE: 800-695-2540
15
Remote Control Emergency Power Down Feature
Your Motion SELECT adjustable foundation has
an emergency lowering feature in the event that
your base is in the raised position and has lost
power due to a power outage.
STEP 3
Replace the battery cover.
STEP 1
Locate and remove the cover for the 9 volt
batteries.
Figure 3: Replace battery cover.
STEP 4
Press the “FLAT” button (A) or the individual
lowering buttons (B, C).
Figure 1: 9 volt batteries cover.
STEP 2
Install the two (2) alkaline 9 volt batteries.
Figure 4: Lower the bed using the 9 volt
battery backup system.
Your bed should lower to the flat position.
NOTE: The two (2) 9 volt batteries are
only intended to be used once. After
you complete the emergency lowering,
the batteries need to be replaced with
new alkaline batteries.
Figure 2: Install 9 volt batteries.
CUSTOMER SERVICE: 800-695-2540
16