ABT DUAL-BEAM ACTIVE PHOTOELECTRIC INTRUDER
DETECTOR WITH DIGITAL FREQUENCY CONVERSION
INSTALLATION GUIDE
Model:
ABT-20
(Outdoor 20m, Indoor 60m)
ABT-30
(Outdoor 30m, Indoor 90m)
ABT-40
(Outdoor 40m, Indoor 120m)
ABT-60
(Outdoor 60m, Indoor 180m)
ABT-80
(Outdoor 80m, Indoor 240m)
ABT-100
(Outdoor 100m, Indoor 300m)
Wiring terminal
Response time
Adjustment knob
Tamper switch
Indicator
Vertical fine-tune knob
Voltage test hole
Bracket
Viewfinder
Collimation hole
Lens
Receiving box
POWER: Transmitting indicator
Housing locking screw
LEVEL: Lightness of the indicator increases with
the accuracy of beam alignment.
ALARM: The indicator turns on when alarm
presents.
GOOD: The green indicator turns on when the
beam aligns with the receiver. If fails to align, the
indicator will off.
Multi sensors may be used for long-distance
guarding. Please install according to the below
diagram to avoid interference between beams.
Adjustable angle: horizontal 90
vertical 10
Direct sunlight, lamplig
Installation heigh 0.7m
1.0m
50mm
50mm
Guarding distance
Beam spread diameter
Horizontal
180
(
S
ABT-20
ABT-30
ABT-40
ABT-60
ABT-80
ABT-100
90
)
G
V
B
20m
30m
40m
60m
80m
100m
0.6m
0.7m
1.0m
1.5m
1.8m
2.1m
1.Remove the cover
Installation of fixed bracket
1.Drill a hole on the bracket and
extend out the cable from it.
2.Attach the paper stencil onto the location
where the equipment is to be mounted, and
drill the holes in the positions on its mark.
2.Remove the cover.
3.Put the cable through the hole for wiring.
3.Fasten the base-plate to the bracket.
Wiring hole
4.Fix the main body onto the wall
15mm
5.Connect the cable to the wire terminal.
(Back-to-back installation guiding diagram)
power supply
spare terminals
Tamperproof
switch terminal
transmitter
alarm output
receiver
6.Put on the cover after adjusting
the response time of the beam.
Wiring distance between transmitter and receiver
Tamperproof
switch terminal
power supply
DC13.8V
DC24V
300m
300m
400m
800m
700m
1400m
1000m
2000m
1.Remove the cover and connect power.
2.Observe the collimation effect at a distance of 5cm
from the viewfinder.
3.Adjust the vertical adjustment screw and the
horizontal angle adjusting wheel in order that the
image of opposite detector falls into the central part
of the viewing hole. At this time, the GOOD indicator
of receiver shall light up; if not, adjust it repeatedly.
The accuracy of beam alignment turns higher;
the red LEVEL indicator becomes brighter.
5cm
Vertical adjustment screw
down
up
horizontal adjustment bracke
1. Insert the test pen into the test hole (please
note the +,- polarity)
2. First adjust the horizontal angle until the test
hole voltage output maximize. Then adjust the
vertical angle by the same way till the voltage
reaches the value above that of below diagram.
3. If it can't reach 1.1V or higher voltage, the
transmitter and receiver shall be regulated again.
Multimeter selects DC 10V
:1
F
F
(1.2m/s):3
N
2
(0.7m/s):4
S
W
.
T
R
Transmitting
The 2 indicators of green LED light up
GOOD LEVEL indicators light up
The red ALARM indicator light up
(0.4m/s):5
The LED of the transmitter doesn't light up Power
The LED of the receiver doesn't light up
open circuit
Power f
open circuit
ABT-20
ABT-30
ABT-40
ABT-60
ABT-80
ABT-100
20m
30m
40m
60m
80m
100m
60m
60m
120m
180m
240m
300m
200m
350m
450m
650m
900m
1100m
65mAmax
65mAmax
The LED of the receiver doesn't light up
when the
Alert distance
2 beams
2 beams blocked simultaneous
Infrared digital pulse beam
50
700msec
Relay contact output: NO. NC contact rating: AC/DC30V 0.5AMax
DC13.8
24V
AC11
40mAmax
O
-25
-55
18V
40mAmax
P 15W
55mAmax
5%-95%RH(relative humidity)
Refer to its diagram
Contact output: NC contact rating DC24V 0.5Amax
H
V
180
20
(
(
90
10
)
)
Calefaction housing (optional)
PC resin
658g(receiver +transmitter)
1150g
www.metroman.hu
55mAmax
Recommended
installation
T
100
T-100
120mm
200
T-200
120mm
I
I-100
100mm
Installation bracket
80
Dimensions
75mm
I-200
200mm