JWX6082 Mini PCI-e User`s Manual

JWX6082 Mini PCI-e User’s Manual
1. Product Overview
The JWX6082 Mini PCI-e adapter cards contain an Atheros AR9390-AL1B
chip for IEEE 802.11a/b/g/n Wireless LAN applications. The mini PCI -e
adapter cards support key security features like Wi-Fi Protected Access
(WPA), WPA2, WEP and 802.1x.
Typical application of the card is integration into other wireless products
such as AP/ Router which is used distance 20cm away human body.
2. Packaging Contents
The mini PCI-e card package contains the following item(s):
1 x Wireless Mini PCI-e Adapter
3. Installation guide
Shut down the power of the platform
Align the Mini PCI-e adapter with the Mini PCI-e socket on the platform
Adjust and push down the Mini PCI-e adapter gently until the metal
locking levers on the Mini PCI-e socket is latched. (Please take note
that the Mini PCI-e adapter can only fit in one direction due to the keyed
notch. Wrong orientation will cause improper installation and may
damage the Mini PCI-e socket)
Connect the antenna(s) on the mini PCI-e module
Reboot on the platform
Install drivers if necessary
4. Frequency
802.11b/g/n: 2412 ~ 2462 MHz
802.11an: 5180 ~ 5240MHz, 5745 ~ 5825MHz
Connector: Reverse U.FL PLUG
5. FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
jjPlus CORP.
13F-3, No.120, Qiaohe Rd., Zhonghe Dist., New Taipei City 235, Taiwan
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
6. FCC Caution
For product available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
7. FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following
conditions:
1)
The antenna must be installed such that 20 cm is maintained
between the antenna and users, and the maximum antenna gain allowed
for use with this device is 2dBi.
2)
The transmitter module may not be co-located with any other
transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed
jjPlus CORP.
13F-3, No.120, Qiaohe Rd., Zhonghe Dist., New Taipei City 235, Taiwan
8. Important Notes
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used
on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
9. Label for end product must include
This transmitter module is authorized only for use in device where the
antenna may be installed such that 20 cm may be maintained between the
antenna and users. The final end product must be labeled in a visible area
with the following: “Contains FCC ID: W23-JWX6082”. The grantee's FCC
ID can be used only when all FCC compliance requirements are met.
10. Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end
user regarding how to install or remove this RF module in the user’s manual
of the end product which integrates this module.
The end user manual shall include all required regulatory
information/warning as show in this manual.
jjPlus CORP.
13F-3, No.120, Qiaohe Rd., Zhonghe Dist., New Taipei City 235, Taiwan