12CX 12CX PROFESIONAL LOUDSPEAKERS al Co Axial C So ea r ixei s KEY FEATURES ● ● ● ● ● ● ● Considerable power handling: 100 w AES (low frequencies) and 15 w AES (high frequencies) Combination of a 12" bass loudspeaker and a compression tweeter L.F. unit: 2" (52 mm) copper voice coil H.F. unit: 1" (25.8 mm) copper voice coil Aluminium diaphragm tweeter The concentric mounting reduces phasing problems in the crossover region Linear and coherent response GENERAL DESCRIPTION This dual loudspeaker includes, in a single unit, a 12” bass driver and a concentrically mounted compression tweeter. This provides a single point source and reduces phasing problems in the crossover region. The bass driver features a 2” (52 mm) voice coil diameter, attached to a lightweight curvilinear cone, and shows a smoothly extended frequency response up to 7 kHz. The tweeter has excellent efficiency and fast response to transient attacks. FREQUENCY RESPONSE AND DISTORTION CURVES FREQUENCY RESPONSE AND DISTORTION CURVES, L.F. UNIT Note: on axis frequency response measured with loundspeaker standing on infinite baffle in anechoic chamber, 1w @ 1m. PREDICTED LOW FREQUENCY RESPONSE Note: Bass-reflex cabinet, Vb=50 I, fb=50 Hz FREQUENCY RESPONSE AND DISTORTION CURVES, H.F. UNIT 12CX 12CX PROFESIONAL LOUDSPEAKERS Coaxial TECHNICAL SPECIFICATIONS DIMENSION DRAWINGS L.F. UNIT Nominal diameter 300 mm. 12 in. Rated impedance 8 ohms. Minimum impedance 7.8 ohms. Power capacity* 100 w AES Program Power 200 w Sensitivity 104 dB 2.83v @ 1m @ 2 Frequency range 45-7000 Hz Recom. enclosure vol. 30 / 100 l 1.06 / 3.53 ft.3 Voice coil diameter 52 mm. 2 in. Magnetic assembly weight 3.85 kg. 8.5 lb. BL factor 13 N/A Moving mass 0.039 kg. Voice coil length 11 mm. Air gap height 7 mm. X damage 16 mm. H.F. UNIT Rated impedance Minimum impedance Power capacity Frequency range Sensitivity 1w @ 1m Voice coil diameter Flux density BL factor Dispersion MATERIALS 8 ohms. 8.2 ohms. @ 7kHz 15 w AES 3500 - 20000 Hz 154 dB 25.8 mm. 1 in. 1.45 T 4 N/A 90° THIELE-SMALL PARAMETERS** Resonant Frequency, fs D.C. Voice Coil Resistance, Re Mechanical Quality Factor, Qms Electrical Quality Factor, Qes Total Quality Factor, Qts Equivalent Air Volume to Cms, Vas Mechanical Compliance, Cms Mechanical Resistance, Rms Efficiency, ηo (%) Effective Surface Area, Sd (m2) Maximum Displacement, Xmax Displacement Volume, Vd Voice Coil Inductance, Le@ 1kHz 42 Hz 6.22 ohms. 3.5 0.38 0.34 146.4 l 373 µm/N 2.91 kg/s 2.65 0.053 m2 2 mm. 106 cm.3 0.7 mH Notes: * The power capacity is determined according to AES2-1984 (r2003) standard. Program power is defined as the transducer's ability to handle normal music program material. L.F. UNIT Basket: Die cast aluminium ● Cone: Paper ● Surround: Plasticised cloth ● Voice coil: Copper ● Magnet: Ferrite ● H.F. UNIT ● Diaphragm: Aluminium ● Voice coil: Copper ● Voice coil former: Kapton MOUNTING INFORMATION Overall diameter Bolt circle diameter Baffle cutout diameter: -Front mount -Rear mount Depth Volume displaced by driver Net weight Shipping weight 320 mm. 12.6 in. 299 mm. 11.77 in. 282 mm. 11.10 in. 280 mm. 11.02 in. 157 mm. 6.18 in. 5.5 l 0.16 ft.3 5.26 kg. 11.57 lb. 5.9 kg. 13 lb. ** T-S parameters are measured after an exercise period using a preconditioning power test. The measurements are carried out with a velocity-current laser transducer and will reflect the long term parameters (once the loudspeaker has been working for a short period of time). acústica beyma, s.a. Polígono Industrial Moncada II . C/. Pont Sec, 1c . 46113 MONCADA - Valencia (Spain) . Tel. (34) 96 130 13 75 . Fax (34) 96 130 15 07 . http://www.beyma.com . E-mail: firstname.lastname@example.org .