DA Manual Template

REGULATORY COMPLIANCE
FSR'S ELECTRONIC PRODUCTS have been tested for compliance with: FCC Class A
and CE The Power Adapter has been tested for compliance with: UL, CSA and CE.
WARRANTY POLICY
This product is warranted against failures due to defective parts or faulty workmanship for
a period of one year after delivery to the original owner. During this period, FSR will make
any necessary repairs or replace the unit without charge for parts or labor. Shipping charges
to the factory or repair station must be prepaid by the owner, return-shipping charges, via
UPS / FedEx ground, will be paid by FSR.
This warranty applies only to the original owner and is not transferable. In addition, it does
not apply to repairs done by other than the FSR factory or Authorized Repair Stations.
This warranty shall be cancelable by FSR at its sole discretion if the unit has been
subjected to physical abuse or has been modified in any way without written authorization
from FSR. FSR’s liability under this warranty is limited to repair or replacement of the
defective unit.
FSR will not be responsible for incidental or consequential damages resulting from the use
or misuse of its products. Some states do not allow the exclusion of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which vary from state to state.
Warranty claims should be accompanied by a copy of the original purchase invoice
showing the purchase date (if a Warranty Registration Card was mailed in at the time of
purchase, this is not necessary). Before returning any equipment for repair, please read the
important information on service below.
CVD-2EQ / CVD-2EQA
SVD-2EQ / SVD-2EQA
1 x 2 COMPOSITE VIDEO LINE DRIVER
WITH AND WITHOUT AUDIO
1 X 2 S-VIDEO LINE DRIVER
WITH AND WITHOUT AUDIO
OPERATIONS MANUAL
SERVICE
Before returning any equipment for repair, please be sure that it is adequately packed and
cushioned against damage in shipment, and that it is insured. We suggest that you save
the original packaging and use it to ship the product for servicing. Also, please enclose a
note giving your name, address, phone number and a description of the problem.
NOTE: all equipment being returned for repair must have a Return Authorization
(RMA) Number. To get a RMA Number, please call the
FSR Service Department (973-785-4347).
Please display your RMA Number prominently on the front of all packages.
Contact Information:
244 Bergen Boulevard,
West Paterson, NJ 07424
Tel: (973) 785-4347 · Fax: (973) 785-4207
E-Mail: sales@fsrinc.com · Web: http://www.fsrinc.com
PROPRIETARY INFORMATION
All information in this manual is proprietary to and the
property of FSR inc. This publication is protected by the
Federal Copyright Law, with all rights reserved. No part
of this document may be reproduced, transcribed, or transmitted, in any form or by any means, without prior
explicit written permission from FSR inc.
244 Bergen Boulevard, West Paterson, NJ 07424
Tel: (973) 785-4347 · Fax: (973) 785-4207
E-Mail: sales@fsrinc.com
Web: http://www.fsrinc.com
43847
CVD-2EQ / CVD-2EqA
SVD-2EQ / SVD-2EQA
1 x 2 COMPOSITE VIDEO LINE DRIVER WITH AND WITHOUT AUDIO
1 X 2 S-VIDEO LINE DRIVER WITH AND WITHOUT AUDIO
OPERATIONS MANUAL
Video Connections ( All Models )
SVD - 2EQ
SVD - 2EQA
INPUT: Connect the appropriate video source cable to the video input on the amplifier.
Connector type will vary depending on the model number of the amplifier.
OUTPUT: Connect the “A” and “B” video outputs to the display devices.
Audio Connections ( Only on models with audio option )
INPUT: The stereo or mono unbalanced audio source can be connected to either the
stereo mini jack or the right and left RCA input jacks depending on the application. Refer
to the drawing below for pinouts and termination.
OUTPUT: The audio output connector can be configured for either balanced or unbalanced audio loads. Connect the output leads to the 5 pin pluggable screw terminals as
shown below. External jumpers may be required depending on the output requirements.
Power Connections:
Attach the 9 VDC power adapter to the two-pin power input jack the amplifier. Plug the
power adapter into a 117 VAC wall outlet. The indicator LED should be yellow when the
amplifier is properly powered and turn green in the presence of a proper video signal from
the source.
Cable Equalization Adjustments:
Cable equalization adjustment potentiometers are provided at each of the video inputs on
the amplifier. Turn each knob while viewing the video sources and adjust for optimum
display quality.
F ig . 1 : O u tp u t C o n n e c to r W ir in g
B a la n c e d
W ir in g
L
+
L
-
S H
R
U n b a la n c e d
+
-
W ir in g
+
-
S H
R
+
-
CVD - 2EQ
CVD - 2EQA
TECHNICAL SPECIFICATIONS:
Video Input
Number/type:
Connectors:
Level (nominal):
Level (maximum):
Impedance:
1 Composite on CVD’s & 1 S – Video on SVD’s
1 BNC Female on CVD’s & 1 4-pin d-sub on SVD’s
Analog 0.7v p-p
2v p-p
75 ohms
Video Output
Number/type:
Connectors:
Bandwidth:
Level (nominal):
Gain:
Impedance:
2 Composite on CVD’s & 2 S – Video on SVD’s
2 BNC Female on CVD’s & 2 4-pin d-sub on SVD’s
100 MHz @ -3 dB
Unity / User adjustable via knobs for each output
Adjustable for cable runs of 1’ to 500’
75 ohms
Audio
Gain:
Bandwidth:
THD + Noise:
Noise Floor:
Stereo Separation:
Unity
20 Hz to 20 kHz (+/-0.05 dB)
0.01% @ 20 kHz at rated Max Output S/N >98 dB
better than 98 dB
-90 dB @ 1 kHz
Audio Input
Number/type:
Connectors:
Impedance:
Max level:
1 stereo unbalanced
1/8” mini connector & 2 RCA’s
10K Ohms DC coupled unbalanced
+6 dBv (.775v = 0dBv)
J u m p e r
F ig . 2 : U n b a la n c e d In p u t C o n n e c to r P in o u t
Audio Output
Number/type:
Connector:
Impedance:
Maximum Level:
2 Balanced / Unbalanced Stereo
5 Position Captive screw terminal
50 ohm
600 ohms: +12 dBv Balanced / +6 dBv Unbalanced
Hi – Z: +14 dBv Balanced / +8 dBv Unbalanced
R in g = R ig h t
T ip = L e ft
S le e v e = G n d
General
Power:
Enclosure Type:
Size:
Approvals:
9v AC, 50/60 Hz: 8 – 14v DC, wallmount AC power supply ( Included )
Metal
5.125" L X 3.39" W X 1.312" D
Power supply is UL/CSA approved