UV Spectra Batten - Prolight Concepts

UV Spectra Batten
12 x 5W UV LEDs
User Manual
Convection
cooled,
no fan!
Optional
IR remote
Order ref:
LEDJ90E
Order code: LEDJ98
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Before your initial start-up, please make sure that there is no damage caused during transportation.
• Should there be any damage, consult your dealer and do not use the equipment.
• To maintain the equipment in good working condition and to ensure safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this manual.
• Please note that damages caused by user modifications to this equipment are not subject to warranty.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modification to the equipment.
• Never let the power cable come into contact with other
cables. Handle the power cable and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the unit.
• Do not open the equipment and do not modify the unit.
• Do not connect this equipment to a dimmer pack.
• Do not switch the equipment on and off in short intervals,
as this will reduce the system’s life.
• Only use the equipment indoors.
• Do not expose to flammable sources, liquids or gases.
• Always disconnect the power from the mains when equipment is not in use or before cleaning! Only handle
the power-cable by the plug. Never pull out the plug by
pulling the power-cable.
• Make sure that the available voltage is between
110~240V, 50/60Hz.
• Make sure that the power cable is never crimped or damaged. Check the equipment and the power cable
periodically.
• If the equipment is dropped or damaged, disconnect the
mains power supply immediately and have a qualified
engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature fluctuation (e.g. after transportation), do not connect power or switch it on immediately. The arising condensation might damage the equipment.
Leave the equipment switched off until it has reached
room temperature.
• If your product fails to function correctly, stop use
immediately. Pack the unit securely (preferably in the original packing material), and return it to your Pro Light
dealer for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualified technician. THIS UNIT CONTAINS
NO USER SERVICEABLE PARTS.
• WARRANTY: One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and/or property.
www.prolight.co.uk
UV Spectra Batten User Manual
2
Product overview & technical specifications
UV Spectra Batten
Housing 12 x 5W UV LEDs this 1m UV Spectra Batten will fill a variety of venues with an outstanding UV glow. They are also convection cooled for silent operation and feature a 65° beam angle. The 4 push button LED menu or included IR remote allow easy access to the functions including DMX, master/slave, sound active and stand alone modes.
•12 x 5W UV LEDs
•Beam angle: 65° (field angle: 100°)
•DMX channels: 1 or 2 selectable
•Sound active and master/slave modes
•0-100% dimming and variable flash
•Bracket allows for multiple rigging or floor standing applications
•4 push button menu with LCD display
•IEC in/out sockets
•3-Pin XLR in/out sockets
•Convection cooled
•Supplied with IR remote (LEDJ90E)
Specifications
UV Spectra Batten
Power consumption
70W
Power supply
110~240V, 50/60Hz
Fuse
F1A 250V
Dimensions
87 x 1018 x 63mm
Weight
2.2kg
Order code
LEDJ98
63mm
87mm
1018mm
09
11
04
07
RA BATTEN
06
05
08
www.prolight.co.uk
01
DMX IN
UV SPECTRA BATTE
SAFETY EYE
DMX IN
POWER IN
POWER IN
10
MENU
UV SPECTRA BATTEN
ENTER
UP
DOWN
DMX OUT
www.prolight.co.uk
SAFETY EYE
MENU
ENTER
UP
DOWN
DMX OUT
02
01 - Bracket tightening knobs
02 - Bracket
03 - Safety eye
04 - Earth point
www.prolight.co.uk
POWER OUT
POWER OUT
03
05 - LED display
06 - Function buttons
07 - DMX input socket
08 - DMX output socket
09 - IEC power in socket
10 - IEC power out socket
11 - Fuse F1A 250V
In the box: 1 x fixture,
1 x IR remote,
1 x power cable &
1 x user manual
UV Spectra Batten User Manual
3
Operating instructions
DMX channel mode:
To access the DMX channel mode, press the “MODE” button on the rear of the unit to show A001 on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the
desired DMX address. Now press the “ENTER” button to choose one of the 1 or 2 DMX channel modes
using the “UP” and “DOWN” buttons, and press the “ENTER” use the “UP” and “DOWN” buttons to set
what the unit should do if it loses DMX signal. bLC - The unit will blackout if DMX signal is lost.
Soun - The unit will go into sound active mode if DMX signal is lost.
HoLd - The unit will hold the last DMX command if DMX signal is lost.
To exit out of any of the above options, press the “MODE” button.
1 channel mode:
2 channel mode:
Channel
Value
Function
Channel
Value
Function
1
000-255
Master dimmer (0-100%)
1
000-255
Master dimmer (0-100%)
2
000-255
Flash speed (slow to fast)
Static mode:
To access static mode press “ENTER” until the display shows C-00 on the LED display. To adjust the brightness use the “UP” and “DOWN” buttons to select between C-00 ~ C-99. Press the “ENTER” button to confirm the setting. Now use the “UP” and “DOWN” buttons to adjust the
flash speed by selecting between F-00 ~ F-99. Press the “ENTER” button to confirm the setting.
To exit out of any of the above options, press the “MODE” button.
Slave mode:
Press the “MODE” button on the rear of the unit to show SLAU on the LED display and press the “ENTER” button to confirm the setting. The unit will now run in sequence with the master unit.
To exit out of any of the above options, press the “MODE” button.
Please ensure that all slave units are set to the same DMX channel mode as the master unit.
Sound active mode:
To access the sound active mode, press the “MODE” button on the rear of the unit to show SU00 on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the
sound sensitivity level from SU.00 ~ SU.99 and press the “ENTER” button to confirm the setting.
Value: 00 - 99 (00 = low, 99 = high)
To exit out of any of the above options, press the “MODE” button.
Menu system
Static mode
C-00~C-99 Brightness (0-100%)
F-00~F-99 Flash speed (slow-fast)
DMX mode
1CH, 2CH
Address setting
A001~A512
Slave mode
SLAV
IR function
Sound active mode
SU00~SU99
Iron - IR On
IroF - IR Off
www.prolight.co.uk
UV Spectra Batten User Manual
4
Operating instructions
Included IR remote functions:
Button functions:
01 - Blackout
02 - To set the brightness of the LED either select 20%, 50% or 100% or alternatively you can use the ‘+’ and ‘-’ buttons
03 - Flash off
04 - To set the flash speed of the LED either select 20%, 50% or 100% or alternatively you can use the ‘+’ and ‘-’ buttons
05 - Sets the LED fixture into DMX mode
06 - Sets the LED fixture into sound active mode
07 - Sets the LED fixture into slave mode
08 - Sets the DMX address for the LED fixture
02
01
04
DIMMING
03
OFF
20%
100%
50%
100%
SLAVE
SET ADDR
SL
S
07
STROBE
06
05
50%
OFF
20%
DMX MODE SOUND ACTIVE
D
SA
1 2 3 +
4 5 6 0
_
7 8 9
08
Included
IR remote
Order code:
LEDJ90E
DMX address examples:
To set the DMX address;
• Press the “S” button, the LED fixture will illuminate in full, you can now start to set the DMX address
• Select the required 3 digit DMX address (eg 001 or 136 or 275) the unit will then flash to confirm the address has been set
• Now press the “DMX MODE” button to save the new address into the memory
Important notes:
• Set the DMX address on each fixture before plugging into the DMX controller
• The IR remote cannot be used when the fixture(s) are being controlled with a DMX controller
• The maximum IR transmitter distance is 10m - Please make sure that you have the IR remote aimed directly at the front panel of each fixture to be programmed
• If you do not press the “DMX MODE” button after you have changed the DMX address when you power down the fixture it will lose the address you have set
www.prolight.co.uk
UV Spectra Batten User Manual
5
DMX setup
Setting the DMX address:
The DMX mode enables the use of a universal DMX controller. Each fixture requires a “start address”
from 1- 512. A fixture requiring one or more channels for control begins to read the data on the channel
indicated by the start address. For example, a fixture that occupies or uses 7 channels of DMX and was
addressed to start on DMX channel 100, would read data from channels: 100,101,102,103,104,105
and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in the
chain starts at 107.
DMX 512:
DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent
fixtures and controllers. A DMX controller sends DMX data instructions form the controller to the fixture.
DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a data “out” terminal).
DMX linking:
DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.
DATA cable (DMX cable) requirements (for DMX operation):
This fixture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit.
Your unit and your DMX controller require a standard 3-pin XLR connector for data input/output, see image below.
Further DMX cables can be
purchased from all good sound
and lighting suppliers or Pro Light Concepts dealers.
Please quote:
CABL10 – 2m
CABL11 – 5m
CABL12 – 10m
Also remember that DMX cable must be daisy chained and cannot be split.
www.prolight.co.uk
UV Spectra Batten User Manual
6
DMX setup
Notice:
Be sure to follow the diagrams below when making your own cables. Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing. Grounding the shield could cause a short circuit and erratic behaviour.
Special note:
Line termination:
When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)
Termination reduces signal transmission
problems and interferance. it is always
advisable to connect a DMX terminal,
(resistance 120 Ohm 1/4 W) between pin 2
(DMX-) and pin 3 (DMX+) of the last fixture.
5-pin XLR DMX connectors:
Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a
3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
www.prolight.co.uk
UV Spectra Batten User Manual
7
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed of
with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
local government office, for details of where and how they can take this item for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
www.prolight.co.uk
UV Spectra Batten User Manual
8