Owners Manual

Owners Manual
3UFO52+LK
35036
35037
5UFO52+LK
35034
35035
Net weight
Net weight
3UFO52+LK
5UFO52+LK
KGS.
KGS.
LBS.
LBS.
UL
R
Warning : Read and follow these instructions carefully and be mindful of all warnings shown throughout.
READ AND SAVE THESE INSTRUCTIONS
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO
PERSONS, PLEASE OBSERVE THE FOLLOWING :
1. To ensure the success of the installation, be sure to read the instructions and review the diagrams
thoroughly before beginning.
2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
All electrical connections must be made in accordance with local codes, ordinances and/or the
National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and
products, secure the services of a qualified and licensed electrician as well as someone who can
check the strength of the supportive ceiling members and make the proper installations and
connections.
3. Make sure that your installation site will not allow rotating fan blades to come in contact with any
object. Blades should be at least 7 feet from floor when fan is in operation.
4. If possible, mount ceiling fan on a ceiling joist - the joist must be able to support the motion and weight
of the moving fan. If the fan will be mounted on a ceiling outlet box, a 4" x 2-1/8" deep METAL octagon
box is required ; one UL listed as " suitable for fan support ". The box and its supporting members must
not be able to twist or work loose. DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling
should be performed by qualified personnel.
5. Blades should be attached after motor housing is hung and in place. Fan motor housing should be
kept in carton until ready to be installed to protect its finish. If you are installing more than one ceiling
fan, make sure that you do not mix fan blade sets.
6. After making electrical connections, spliced conductors should be turned upward and pushed
carefully up into outlet box. The wires should be spread apart with the grounded conductor and the
equipment - grounding conductor on one side of the outlet box and the " HOT " wires on the other side.
7. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed
and should be installed per the light kit's installation instructions.
8. After fan is completely installed, check to make sure that all connections are secure to prevent fan
from falling and/or causing damage or injury.
9. The fan is ready for operation after installation. The bearings are adequately lubricated.
No additional lubricating is necessary.
10. The fan must be turned off and stopped before reversing fan direction.
11. This fan is suitable for indoor location.
P1
1.Unpack and inspect fan carefully to be certain all
contents are included.
Hardware Bag
Mounting Bracket
Wall Remote
Canopy
Yoke cover
(for 35036/35037)
Fan assembly
Hardware Bag
Downrod
Yoke cover
Assembly
(for 35034/35035)
Wood Screw
2pcs.
Wire Nut
5pcs.
Mounting Screw
2pcs
Spring Washer
2pcs
Lock Washer
2pcs
Wire Nuts
3pcs
Blade Balance Kits
1pcs
Blade Screw
9/11pcs
Paper Washer
9/11pcs
Glass
Outlet Box
Mounting Bracket
OF F OF F OF
F
3.
2.
Turn off power at breaker box
to avoid possible electrical
shock.
Use metal outlet box suitable for
fan support.
Secure outlet box directly to the
building structure using ceiling joist
screws (included).
Outlet box must support 40 lbs min.
4.
Install mounting bracket to
outlet box in ceiling using
washers and the screws
provided with the outlet
box.
5A. Yoke & Downrod Assembly (for 35034/35035)
1.Take cross pin and cotter pin from downrod.
2.Insert downrod assembly through the yoke
cover assembly and canopy as shown.
3.Feed motor lead wires through downrod assembly.
Canopy
Yoke Cover
Assembly
Wire Connectors
from Yoke Cover
Assembly
Canopy
Yoke Cover
Assembly
Yoke
Downrod
Assembly
Fan
Assembly
Downrod
Cross Pin
Yoke
Fan
Assembly
Wire Connectors
from Fan
Cotter Pin
Set Screw
with Hex Nut(2)
Downrod
Assembly
4.Insert the downrod assembly into yoke.
5.Insert the cross pin through Yoke and downrod
and secure with Cotter Pin.
6.Tighten both set screws to further secure downrod.
7.Attach wire connectors from yoke cover
assembly and from fan together.
8.Pull down the yoke cover assembly and fasten the
set screw on top of yoke cover assembly.
P2
Yoke Cover
Assembly
Canopy
Fan
Assembly
5B. Yoke & Downrod Assembly (for 35036/35037)
Canopy
Canopy
Yoke Cover
Yoke
Yoke Cover
Downrod
Assembly
Downrod
Cotter Pin
Cross Pin
Yoke
Fan
Assembly
Canopy
Downrod
Assembly
Fan
Assembly
Yoke Cover
Set Screw
with Hex Nut(2)
Fan
Assembly
5a. Take off cross pin and cotter pin from downrod,
then insert lead wires through yoke cover, canopy
and downrod.
5d. Tighten both set screws from yoke to further
secure downrod.
5b. Insert the downrod assembly into yoke.
5e. Pull down the yoke cover through
downrod and put in place.
5c. Insert the cross pin through Yoke and downrod
and secure with cotter pin.
5f. Insert canopy through downrod.
6. Hanging the Fan
Mounting
Bracket
Ridge
Mounting
Bracket
Ball Groove
6b.
Carefully lift fan assembly onto mounting bracket.
Rotate fan so that the groove on the ball engages
the ridge in the mounting bracket.
6a.
Lift fan assembly onto mounting bracket.
7.Make Wire Connection for Remote Controller
7-1. Set Remote Control codes:
1
4
4
1 2 3
Receiver
Code Switches
2
3
Transmitter
Code Switches
This unit has 16 different code combinations.
1.Setting the code on the TRANSMITTER
A. Remove battery cover.
B. Slide code switches to your choice of ON or OFF position. Use a small screwdriver or
ball point pen to slide each switch firmly up or down.
C. Install 9V DC battery ( NOT included ).
D. Install battery cover on transmitter.
2.Slide code switches on the Receiver to be the SAME POSITIONS as set on your Transmitter.
3.Remote features ON/OFF light operation.
P3
7-2. Make wire connection
Follow diagram below and make sure that all exposed wires are secured inside wire nuts or terminal black.
Note : Wires from house may vary in color and may not include ground wire ( green ). After wiring is
completed, gently push wires into junction box with wire nuts pointing upward.
From House
From Remote
White
White
( AC - N )
Black
Bla
From Fan
White
Blac
ck
Bl
( AC - L )
White
( Motor - N )
k
Black
ue
( Motor - L )
Blue
( for light kit )
Green
Green
( from downrod )
( for ground wire )
Green
( from mounting bracket )
Secure with twist - lock wire nuts. (Included)
8. Canopy installation
Key Holes
Canopy
1.Install remote control receiver into mounting bracket.
2.Push up the Canopy until the two screws on mounting
bracket are engaged with Key Holes in canopy.
3.Rotate the canopy slightly until the two screw heads
are in the small end of the Key Holes.
4.Tighten both screws.
Screw
Mounting
Bracket
Remote Control
Receiver
Canopy
9. Blade Installation ( With Light Kit Pan Attached )
9A. Remove The plate at fan bottom that covers the rectangular hole.
9B. (1) Insert blade into fan blade hole.
(2) Fasten blade onto motor assembly through rectangular hole
using the washer & motor screws provided from hardware bag.
9C. Re-attach the plate in place after blade installation is completed.
Fan
Blade Hole
Blade
Rectangular Hole
Blade
Plate
Washer
Blade screw
9A
9B
Plate
9C
P4
10. Lamp Holder Installation
Groove
Bulb
Ridge
Glass
Shade
Attach & rotate down glass shade
clock wisely to light kit pan.
Install bulbs ( max. 40w x2, included )
to lamp holder.
11. Turn the power on - your fan is ready for operation.
P5