Vision15 Vision15 Turbo Hardware System

USER MANUAL
VERSION 1.0 November 2011
Vision15
Vision15 Turbo
Hardware System
Copyright 2011
All Rights Reserved
Manual Version 1.0
Part Number:
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not
limited to, the implied warranties of merchantability and fitness for a particular
purpose. We shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of
this material.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced
or translated to another language without the prior written consent of the
manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Other trademarks mentioned herein are the property of their respective owners.
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrical power supply, turn off the power
switch and remove the power cord plug from the wall socket. The wall socket must
be easily accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for
ventilation to ensure reliable operation of the product and to protect it from
overheating. These openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should never be placed near or over a radiator or heat
register or in a built-in installation unless proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking
label. If you are not sure of the type of power available, consult your dealer or local
power company.
8. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as they
may touch dangerous voltage points or short out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
ii
CE MARK
This device complies with the requirements of the EEC directive 2004/108/EC with
regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage Directive”.
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
may cause undesired operation.
CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly. Replace only
with the same or equivalent type recommended by the manufacturer. Discard used
batteries according to the manufacturer’s instructions.
Battery Caution
Risk of explosion if battery is replaced by an incorrectly type. Dispose of used
battery according to the local disposal instructions.
Safety Caution
Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S)
related legislation, peripherals shall be 4.7.3.2 “Materials for fire enclosure”
compliant.
4.7.3.2 Materials for fire enclosures
For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material
of a FIRE ENCLOSURE, in the thinnest significant wall thickness used, shall be of
V-1 CLASS MATERIAL or shall pass the test of Clause A.2.
For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all
STATIONARY EQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest
significant wall thickness used, shall be of 5VB CLASS MATERIAL or shall pass the
test of Clause A.1
iii
LEGISLATION AND WEEE SYMBOL
2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dust bin symbol on the device means that it should not be disposed
of with other household wastes at the end of its working life. Instead, the device
should be taken to the waste collection centers for activation of the treatment,
collection, recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can
take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
iv
Revision History
Changes to the original user manual are listed below:
Revision Description
1.0
•
Initial release
Date
November 2011
v
Table of Contents
1. Packing List .............................. 1
1-1. Standard Accessories ..............................................1
1-2. Optional Accessories ...............................................2
2. System View ............................. 3
2-1.
2-2.
2-3.
2-4.
Front & Side View ....................................................3
Rear View with stand ...............................................3
I/O Ports View..........................................................4
System Dimension...................................................5
3. System Assembly & Disassembly 6
3-1.
3-2.
3-3.
3-4.
3-5.
Stand Disassembly ..................................................6
Power Adapter Replacement ...................................6
HD Replacement .....................................................7
Open the System .....................................................8
RAM Replacement ..................................................9
4. Peripheral Installation ............ 10
4-1.
4-2.
4-3.
4-4.
4-5.
4-6.
vi
MSR Installation .....................................................10
Fingerprint Installation ............................................ 11
Second Display Installation ....................................13
Wall Mounting Kit Installation .................................14
Cable Cover Installation .........................................15
Cash Drawer Installation ........................................16
5. Specifications ......................... 18
6. Jumper Setting ........................ 20
6-1. C48 Motherboard....................................................20
6-1-1. Motherboard Layout ................................................ 20
6-1-2. Connectors & Functions .......................................... 22
6-1-3. Jumper & BIOS/Utility Setting ................................. 23
6-2. C68 Motherboard....................................................28
6-2-1. Motherboard Layout ................................................ 28
6-2-2. Connectors & Functions .......................................... 29
6-2-3. Jumper Setting ........................................................ 30
Appendix: Drivers Installation .... 35
vii
The page is intentionally left blank.
viii
1.
1-1.
Packing List
Standard Accessories
a
d
b
e
c
a.
b.
c.
d.
e.
System (with stand)
Driver CD
Power adapter
Power cord
RJ45-DB9 cable (x3)
1
1-2.
Optional Accessories
a
d
b
e
c
f
a.
b.
c.
d.
e.
f.
2
MSR module
VFD module (with RJ-45 cable)
Second display (with VGA cable)
Fingerprint module
Wall mount kit
Cable cover
2.
2-1.
System View
Front & Side View
1
4
5
2
3
Item No.
1
2
3
4
5
2-2.
Description
Touch screen
MSR module (optional)
Rugged footprint
Ventilation
HDD door
Rear View with stand
6
7
Item No. Description
6
VFD dummy cover
7
MSR dummy cover
3
2-3.
I/O Ports View
C48 Motherboard
a
Item No.
a
b
c
d
e
f
g
h
i
j
k
b c
d
e
f gh i j k
Description
Power button
2nd VGA
Parallel
USB x 4
COM 1, 2, 3, 4 (from right to left)
Line-out
Mic-in
Cash drawer
LAN
Power switch
DC-IN
C68 Motherboard
a b c
Item No.
a
b
c
d
e
f
g
h
i
j
k
4
d
e
Description
Power button
Parallel
VGA out
USB x 4
COM 1, 2, 3, 4 (from right to left)
Line-out
Cash drawer
LAN x 2
Power switch
DC-IN
Cable strap
f g h i j k
System Dimension
361mm
337mm
2-4.
248mm
5
3.
3-1.
System Assembly & Disassembly
Stand Disassembly
1. Loosen the thumb screw (x1) and
slide the stand towards the IO
panel to release it from the system.
2. Reverse the steps above to attach
stand to the system.
3-2.
Power Adapter Replacement
Power adapter is secured to the system stand by a holding bracket and screws.
To attach power adapter, please follow the steps below.
1. Route the cable as shown in the
picture.
2. Connect the cable to the DC-IN
port on system IO panel.
6
3-3.
HD Replacement
Please remove the current HDD first.
To remove the HDD from the System
1. Power the system down.
2. Remove the screw(x1) from the HDD door.
3. Open the HDD door.
4. While pinching the HDD bracket
tabs pull the HDD from the
system. For easier removal pull
the plastic puller (see picture) at
the same time.
Disassemble HDD
5. To release the HDD from the bracket gently pull it open until the four pins
are removed.
7
6. To install a new HDD. Attach the
HDD to the bracket until it clicks in
place. Make sure to press the edges
of the drive not the center to avoid
damaging the drive.
7. Finally slide the HDD into the slot till
it clicks.
3-4.
Open the System
1. Place the system face down.
Making sure not to scratch the
screen.
2. Remove the screws (x4) on system
rear cover to open the system.
note: If the system is equipped
with a MSR. The MSR must be
removed first.(refer to Chapter
4-1 and reverse the steps to
remove the MSR)
8
3-5.
RAM Replacement
1. Follow the steps in Chapter 3-4 to
open the system.
2. The RAM is located on the right
side of the system (see picture).
Installing a RAM module
3. Slide the memory module into the
memory slot and press down until
it locks in place.
Removing a RAM module
3. To remove the module pull the
ejector clips out of the side of the
module.
4. Slide the memory out of the slot.
9
4.
4-1.
Peripheral Installation
MSR Installation
MSR module can be installed to either side of the system. Choose one side and
follow the steps below. Make sure the unit is powered down before starting.
1. Remove the screws (x2) to
release the MSR dummy cover.
2. Connect MSR cable to the
connector on system side.
3. Insert MSR module in place and
fasten the screws (x2) on the back
to secure the module.
10
4-2.
Fingerprint Installation
Fingerprint module will be installed to system prior to shipping once it is selected.
To uninstall fingerprint module, please follow the steps below.
1. Loose the thumb screw (x1)
securing the module and slide the
module outward as arrow shown.
2. Loose the screw (x1) fastening the
ground cable and disconnect the
cable from the connector.
3. Disconnect the cable from the USB
port.
4. Reverse the steps above for
installation.
11
1. Follow steps in Chapter 3-1 to disassemble the system stand.
2. Attach the VFD module to system by fastening the screws (x2).
3. Route the cable through cable mangement on the system stand.
4. Connect the RJ-45 cable to COM 4 on the systems IO panel. Make sure the
system is powered off.
12
4-3.
Second Display Installation
1. Follow steps in Chapter 3-1 to disassemble the system stand.
2. Connect one end of the VGA cable to 2nd Display. Route the cable through
cable mangement on the system stand.
3. Attach the 2nd Display to system by fastening the screws (x2).
4. Connect the other end of the VGA cable to 2nd VGA port on system IO panel.
Make sure the system is powered off.
13
4-4.
Wall Mounting Kit Installation
The Wall mounting Kit includes a wall plate, a metal bracket, and one screw. (refer
to Chapter 1-2 item d) Please follow the steps below.
1. Secure the wall plate to the wall by
fastening screws (x4).
2. Attach the metal bracket to the
back of the system by fastening
the screw (x1) as shown.
3. Align the large end of
the teardrop mounting
holes (x4) on the wall
plate with the screws
(x4) on the systems
rear cover. Slide the
wall plate until the
screws are even with
the narrow end.
14
4. Fasten the screw (x1) through the
metal bracket to secure the wall
mount kit.
4-5.
Cable Cover Installation
There are two different cable covers. These can be utilized separately or together. When both are needed, please take care that they are installed in the correct
order.
1. Slide the covers on the IO panel, if
using both covers the large cover
needs to be installed before the
smaller one.
2. Fasten the screws (x3, two for the
larger one and one for the smaller
one) to secure the covers.
15
4-6.
Cash Drawer Installation
You can install a cash drawer through the cash drawer port. Please verify the pin
assignment before installation.
Cash Drawer Pin Assignment
Pin
1
2
3
4
5
6
6
Signal
GND
DOUT bit0
DIN bit0
12V / 19V
DOUT bit1
GND
1
Cash Drawer Controller Register
The Cash Drawer Controller use one I/O addresses to control the Cash Drawer.
Register Location: 48Ch
Attribute: Read / Write
Size: 8bit
BIT
BIT7
Attribute Reserved
BIT6
Read
BIT5
BIT4
Reserved
BIT3
BIT2
Write
BIT1
BIT0
Reserved
7 6 5 4 3 2 1 0
X
X X
X X
Reserved
Cash Drawer “DOUT bit0” pin output control
Cash Drawer “DOUT bit1” pin output control
Reserved
Cash Drawer “DIN bit0” pin input status
Reserved
16
Bit 7: Reserved
Bit 6: Cash Drawer “DIN bit0” pin input status.
= 1: the Cash Drawer closed or no Cash Drawer
= 0: the Cash Drawer opened
Bit 5: Reserved
Bit 4: Reserved
Bit 3: Cash Drawer “DOUT bit1” pin output control.
= 1: Opening the Cash Drawer
= 0: Allow close the Cash Drawer
Bit 2: Cash Drawer “DOUT bit0” pin output control.
= 1: Opening the Cash Drawer
= 0: Allow close the Cash Drawer
Bit 1: Reserved
Bit 0: Reserved
Note: Please follow the Cash Drawer control signal design to control the Cash
Drawer.
Cash Drawer Control Command Example
Use Debug.EXE program under DOS or Windows98
Command
Cash Drawer
O 48C 04
Opening
O 48C 00
Allow to close
► Set the I/O address 48Ch bit2 =1 for opening Cash Drawer by “DOUT bit0” pin
control.
► Set the I/O address 48Ch bit2 = 0 for allow close Cash Drawer.
Command
Cash Drawer
I 48C
Check status
► The I/O address 48Ch bit6 =1 mean the Cash Drawer is opened or not exist.
► The I/O address 48Ch bit6 =0 mean the Cash Drawer is closed.
17
5.
Specifications
Model Name
Motherboard
CPU Support
Chipset
Vision 15
C48
Vision 15 Turbo
C68
Intel Sandy Bridge CPU
i3-2120 3.3G, L2 3M, 65W
Intel Pinevew D525 1.8G L2 1M, dual core 13W
Pentium G850 2.9G, L2 3M, 65W
Celeron G530 2.4G, L2 2M, 65W
Intel Q67 PCH (Processor Controller Hub,
AMT supported_highend)
CPU with Graphic built-in + ICH 8M
Intel H61 PCH (Processor Controller Hub, no
AMT suport_mainstream)
System Memory
2 x SO-DIMM slot up to 4GB DDR3 800MHz
1 x Long DIMM slot up to 8GB DDR3 1066/1333
MHz
Graphic Memory
Shared system memory up to 256MB
Intel HD Graphics 3000/2000, integrated in
CPU, frequency 850MHz, (dynamic up to
1.1GHz)
LCD Touch Panel
LCD Size
Brightness
Maximal Resolution
Touch Screen Type
Tilt Angle
15” TFT LCD
250nits
1024 x 768
Resistive
0° ~ 90°
Storage
HDD
One 2.5” SATA HDD bay
Expansion
PCI-E Socket
1
External I/O Ports
USB
Serial / COM
Parallel
LAN (10/100/1000)
DC Jack
2nd VGA
Cash Drawer Port
Audio Jack
4 ports (V2.0)
4 x RJ45 COM
4 x RJ45 COM
(COM1~COM3 standard RS-232 without
(COM1~COM3 standard RS-232 without
power, COM4 with +12V enable /disable by power, COM4 with +12V enable /disable by
BIOS setting)
BIOS setting)
1
1 x RJ45
2 x RJ45
1
1 (Female)
1 x RJ 11 (12V /24V)
1 x RJ 11 (12V /24V)
1 x Line-out, 1 x Mic-in
1 x Line-out
Audio
Built in Speaker
2 x 2W speakers
Power
Power Adapter
19V / 90W
19V / 120W
Control / Indicator
Power Button
Indicator LED
1
1
Peripheral
MSR
Bio Reader
Second Display
Customer Display
3 Tracks MSR ( PS/2 )
1 (USB)
(optional) 8.4” / 15” 2nd display without touch
Flush mount VFD display 2 x 20 characters (COM)
Environment
EMC & Safety
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Dimension (WxDxH)
Weight (N.W./G.W.)
18
FCC, Class A, CE, LVD
5°C ~ 35°C (41°F ~ 95°F)
-20°C ~ 55°C (-4°F ~ 140°F)
20% ~ 80% RH non condensing
20% ~ 85% RH non condensing
LCD 90 degree : 361 x 248 x 337 mm
7kgs / 8kgs
Mounting
OS Support
100mm x100mm VESA mounting holes for Panel PC type
Windows® XP Professional, Windows
Embedded POSReady 2009, Windows XP
Embedded, Windows XP Professional for
Embedded, WinCE, Vista, Windows 7, Linux
Windows® XP Professional, Windows
Embedded POSReady 2009, Windows
XP Embedded, Windows XP Professional
for Embedded, POSready 7, Vista,
Windows 7, Linux
* This specification is subject to change without prior notice.
19
6.
6-1.
Jumper Setting
C48 Motherboard
15
2
18
PWR1
16
17
6-1-1. Motherboard Layout
MINI_PCIE
CN24
JP12
JP12
CN23
RJ45_2
JP10
JP10
JP19
CN22
CN17
CN18
SKT1
CN16
CN14
CN15
CN20
CN19
JP14
JP14
CN13
AJ
JP8
CN27
JP8
CN8
CN5
SATA2
CN31
JP6
JP18
JP18
RJ45_1
JP20
JP6
JP20
JP5
JP5
JP9
JP9
11
CN21
AG AE AC AA
AH AF AD AB Y W V U T R P N M L K J H G F E D C B A
27 25
23 21 19 17 15
13 11 9 8 7 5
3 1
18 16 14 12
6 4 2
28 26 24 22 20
10
RJ11_1
29
JP19
CN7
JP3
JP4
CN11
JP4
JP3
CN26
SATA1
USB2
CN29
USB1
JP1
JP1
A
B
DC
E
F
G
H
J
K
2 4 6 8 10 12 141618 20 22 24 26 28 30
1 3 5 7 9 111315 171921 23 25 27 29 31
L
M
N
PR
T
VU
W
YAA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
PRN1
FAN_CPU1
DDR3_A1
CN4
JP21
CN1
CN3
JP21
CN25 CN28
SW1
C48 V2.1 TOP LAYER
20
DDR3_A2
C48 V2.1 BOTTOM LAYER
21
6-1-2. Connectors & Functions
Connector
CN1
CN3
CN4
CN5/8
CN11
CN13
CN14
CN15
CN16
CN18
CN20/JP10
CN22
CN23
CN26
CN27
CN29
DDR3_A1
DDR3_A2
PRN1
PWR1
RJ11_1
RJ45_1
RJ45_2
SATA1
SATA2
USB1
USB2
SW1
JP1
JP3/6
JP4/5
JP8
JP12
JP14
JP18
JP19
22
Purpose
Power Button Connector
Printer Port Reset
Printer Port
HDD Power
COM5 For Touch
Card Reader Connector
Line out
HDD LED
Speaker & MIC
MIC IN
System Indicator
USB Port
PS2 KEYBOARD
LVDS
Inverter Connector
System Fan
DDR3 SO-DIMM1
DDR3 SO-DIMM2
Parallel Port
+19V DC Jack
Cash Drawer Connector
COM1, COM2, COM3, COM4
LAN
SATA Connector
SATA Connector
USB1, USB2
USB3, USB4
Power Button
CMOS Operation Mode
VGA Port
COM2 RS232/485/422 Setting
LCD ID Setting
System Reset
Inverter Selection
COM3/4 Power Setting
Cash Drawer Power Setting
6-1-3. Jumper & BIOS/Utility Setting
COM2 RS232/485/422 Setting
Function
JP5
JP4
▲RS232
1 3 5 7 9
2 4 6 8 10
1 3 5 7 9 11
2 4 6 8 10 12
RS485
1 3 5 7 9
2 4 6 8 10
1 3 5 7 9 11
2 4 6 8 10 12
RS422
1 3 5 7 9
2 4 6 8 10
1 3 5 7 9 11
2 4 6 8 10 12
Cash Drawer Power Setting
Function
JP19
+19V
1 3
2 4
▲+12V
1 3
2 4
System Reset
Function
JP12
▲System Normal
1
2
System Reset
1
2
▲ = Manufacturer Default Setting
23
System Indicator
Function
JP10
▲Disable
1 3 5 7
2 4 6 8
Enable
1 3 5 7
2 4 6 8
Inverter Selection
Function
JP14
▲ CCFL
1 3 5
2 4 6
LED
1 3 5
2 4 6
CMOS Operation Mode
CMOS Reset
To clear the CMOS,
1. Remove the power cable from the system.
2. Open the system, and set the ‘CMOS Operation jumper’ from ‘CMOS Normal’
to ‘CMOS Reset’. (refer to the jumper shown below)
3. Connect the power cable to the system, and power on the system:
in ATX mode: press the power button and it will fail power on
in AT mode: turn on system power
4. Remove the power cable from the system.
5. Return the "CMOS Operation mode" jumper setting from "CMOS Reset" to
"CMOS normal".
6. Connect the power cable and power on the system.
Function
JP1
▲CMOS Normal
1
2
CMOS Reset
1
2
▲ = Manufacturer Default Setting
24
COM3 & COM4 Power Setting
For C48, COM3/COM4 power adjustment must be made by BIOS/Utility and
Jumper. Since COM3/COM4 default is “None“ meaning no power, power must be
on through BIOS prior to physical jumper change.
BIOS/Utility setup
1. Press <DEL> key to enter BIOS
SETUP UTILITY when system
boot up.
2. Find tab "Advanced".
3. Select "Power Configuration
COM/VGA Ports" and press
<Enter> to go to sub screen.
4. To switch on the power, select
"Power". Please save the
change before exiting BIOS
so as to go for physical jumper
adjustment.
Jumper Setup
Function
JP18
▲+5V
1 3 5 7
2 4 6 8
+12V
1 3 5 7
2 4 6 8
+5V
1 3 5 7
2 4 6 8
COM3
COM4
▲+12V
1 3 5 7
2 4 6 8
▲ = Manufacturer Default Setting
25
LCD ID Setting
Several configurations are applied to different sizes of panel. Please refer to the
followings to complete relevant settings.
• Jumper Setup
Resolution
Bits
LVDS
Channel
Output Interface
JP8
800 x 600
24
Single
1 3 5 7
2 4 6 8
1024 x 768
24
Single
1 3 5 7
2 4 6 8
1366 x 768
24
Single
1 3 5 7
2 4 6 8
1st: LCD Panel
2nd: VGA port
800 x 600
18
Single
1 3 5 7
2 4 6 8
*800 x 600
18
Single
1 3 5 7
2 4 6 8
1024 x 768
18
Single
1 3 5 7
2 4 6 8
*remark: specialized for Sharp 12.1” LQ121S1LG41/LQ121S1LG42 panel.
1
2
Jumper open
1
2
Jumper short
• 2nd VGA Power Setting
VGA port power must be on through BIOS/Utility for default is “No Power“.
BIOS/Utility setup
1. Press <DEL> key to enter BIOS
SETUP UTILITY when system
boot up.
2. Find tab "Advanced".
3. Select "Power Configuration
COM/VGA Ports" and press
<Enter> to go to sub screen.
26
4. To switch on the power, select
"+12V". Please save the change
before exiting BIOS to avoid data
lost.
• Intel Graphics Driver Setting
1. Right click Desktop. Select the
"Graphics Properties" and enter
the menu.
2. Make sure the Display Device
matches the image.
No.
Output Interface
Connector & Jumper
Intel Graphics Driver
Device Name
1st
LCD Panel
CN26
Notebook
2nd
VGA Port
JP3/6
Monitor
27
6-2.
C68 Motherboard
6-2-1. Motherboard Layout
PWR1
CN18
PWR3
MINI_PCIE1
RJ45_1
JP8
JP9
U7
CN19
RJ11_1
CN15
CN8
JP14
CN21
CN16
JP10
JP13
JP7
CN1
CN4
CN2
CN7
CN9
JP4
JP5
DDR3_A1
SATA2
CN6
RJ45_2
FAN_CPU1
JP3
CN10
CN3
CN11
SKT1
SATA1
B1
JP11
JP12
CN5
JP2
USB1
CN14
USB2
CN12
JP1
CN17
CN13
PRN1
CN20
FAN_SYS1
JP15
SW1
Version: C68 v1.0
28
6-2-2. Connectors & Functions
Connector
CN1/2
CN3
CN4
CN5
CN6
CN7
CN9
CN10/11
CN12
CN13
CN14
CN15
CN16
CN17
CN18/CN19
CN20
CN21
DDR3_A1
FAN_CPU1
FAN_SYS1
PRN1
PWR3
RJ11_1
RJ45_1
RJ45_2
SATA1/2
USB1
USB2
JP2
JP3
JP4/5
JP7
JP8
JP9
JP10/13
JP11
JP12
JP14
SW1
Purpose
SATA power Connector
LVDS Connector
LVDS INVERTER Connector
SATA HDD LED Connector
DVI Connector
BATTERY Connector
FT STATUS INTERFACE
USB Port(Internal)
Card Reader Connector(COM6)
RF Connector
COM5 for Touch
SPEAKER & MIC Connector (Internal)
PS2 Keyboard Connector
Power On LED Connector
LAN1/2 LED(Internal)
Power button(Internal)
Line out JACK
DDR3 LONG-DIMM
CPU FAN Connector
System FAN Connector
PARALLEL PORT
+19V DC JACK
CASH DRAWER Connector
LAN1/LAN2 Connector
COM1/ COM2/ COM3/ COM4
SATA Connector
USB4 USB2
USB3 USB4
LCD ID Setting
INVERTER Select
VGA
CMOS Operation Mode
ME Update
H/W Reset
COM2 RS232/485/422 Setting
USB Touch Power Setting(CN11)
COM3/COM4 Power Setting
CASH DRAWER Power Setting
Power button
29
6-2-3. Jumper Setting
Power Mode Setting
Function
JP1
1
2
▲ATX Power
1
2
AT Power
COM2 RS232/485/422 Setting
Function
JP10
▲RS232
1 3 5 7 9
2 4 6 8 10
1 3 5 7 9 11
2 4 6 8 10 12
RS485
1 3 5 7 9
2 4 6 8 10
1 3 5 7 9 11
2 4 6 8 10 12
RS422
1 3 5 7 9
2 4 6 8 10
1 3 5 7 9 11
2 4 6 8 10 12
Cash Drawer Power Setting
Function
JP14
▲+19V
1 3
2 4
+12V
1 3
2 4
▲ = Manufacturer Default Setting
30
JP13
Inverter Selection
Function
JP3
▲ CCFL
1 3 5
2 4 6
LED
1 3 5
2 4 6
ME Update
Function
JP8
▲Lock
1
2
Un-lock
1
2
Hardware Reset
Function
JP9
▲System Normal
1
2
System Reset
1
2
USB Touch Power Setting for CN11 Connector
Function
JP11
▲+5VSB
1 3
2 4
+5V
1 3
2 4
▲ = Manufacturer Default Setting
31
CMOS Operation Mode
CMOS Reset
To clear the CMOS,
1. Remove the power cable from the system.
2. Open the system, and set the ‘CMOS Operation jumper’ from ‘CMOS Normal’
to ‘CMOS Reset’. (refer to the jumper shown below)
3. Connect the power cable to the system, and power on the system:
in ATX mode: press the power button and it will fail power on
in AT mode: turn on system power
4. Remove the power cable from the system.
5. Return the "CMOS Operation mode" jumper setting from "CMOS Reset" to
"CMOS normal".
6. Connect the power cable and power on the system.
Function
JP7
▲CMOS Normal
1
2
CMOS Reset
1
2
COM3 & COM4 Power Setting
COM3 and COM4 can be set to provide power to your serial device.
The voltage can be set to +5V or 12V by setting jumper JP18 on the motherboard. When enabled, the power is available on pin 10 of the RJ45 serial connector. If you use the serial RJ45 to DB9 adapter cable, the power is on pin 9 of
the DB9 connector.
By default, the power option is disabled in the BIOS.
BIOS/Utility setup
1. Press <DEL> key to enter BIOS
SETUP UTILITY when system
boot up.
2. Find tab "Advanced".
3. Select "Power Configuration
COM/VGA Ports" and press
<Enter> to go to sub screen.
▲ = Manufacturer Default Setting
32
4. To switch on the power, select
"Power". Please save the
change before exiting BIOS
so as to go for physical jumper
adjustment.
COM3/COM4 Jumper setup
Function
JP12
▲+5V
1 3 5 7
2 4 6 8
+12V
1 3 5 7
2 4 6 8
+5V
1 3 5 7
2 4 6 8
COM3
COM4
▲+12V
1 3 5 7
2 4 6 8
33
LCD ID Setting
Panel#
Resolution
LVDS
Output
Bits Channel Interface
1
800 x 600
18
Single
LVDS
Panel
1 3 5 7 9
2 4 6 8 10
3
800 x 600
24
Single
LVDS
Panel
1 3 5 7 9
2 4 6 8 10
5
1024 x 768
18
Single
LVDS
Panel
1 3 5 7 9
2 4 6 8 10
7
1024 x 768
24
Single
LVDS
Panel
1 3 5 7 9
2 4 6 8 10
9
1280 x 1024
24
Dual
LVDS
Panel
1 3 5 7 9
2 4 6 8 10
11
1366 x 768
24
Single
LVDS
Panel
1 3 5 7 9
2 4 6 8 10
13
1440 x 900
24
Dual
LVDS
Panel
1 3 5 7 9
2 4 6 8 10
15
1920 x 1020
24
Dual
LVDS
Panel
1 3 5 7 9
2 4 6 8 10
CRT
1 3 5 7 9
2 4 6 8 10
JP7
Remark:
Panel ID#12 is specialized for Sharp 12.1" LQ121S1LG41/LQ121S1LG42 panel.
1
2
34
Jumper open
1
2
Jumper short
Appendix: Drivers Installation
The shipping package includes a Driver CD in which you can find every individual
driver and utility that enables you to install the drivers on the system.
Please insert the Driver CD into the drive and double click on the “index.htm” to
select the models. You can refer to the drivers installation guide for each driver in
the “Driver/Manual List”.
35