LIQUIDYNAMICS Hose Reel

This manual contains important warnings and information. READ AND KEEP FOR REFERENCE.
LIQUIDYNAMICS
Hose Reel
Instruction & Parts Manual
Large Capacity Spring Rewind Hose Reel
Model 88501-100L
2311 S. Edwards • Wichita, KS 67213
TEL: 316-943-5477 • FAX: 316-943-4760
TOLL FREE: 800-894-3572
E-MAIL: productinfo@liquidynamics.com
! CAUTION
! WARNING
This symbol indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
This symbol indicates a potentially hazardous situation which, if not avoided, may
result in injury or damage to equipment.
Introduction:
4. Flush product supply lines with generous quantities of
product in order to remove air, loose dirt, scale,
shavings, etc. This will
Fig. 3
prevent damage to reels,
meters and control valves.
5. Determine desired
orientation of reel to best
fit your specific
installation. Reels are
shipped with guide arm in
position shown in fig. 3.
These hose reels are a practical, safe, reliable and
economical way to extend the useful life of hoses,
maintain a safe and clean environment and significantly
improve Service Technician efficiency. Typical applications
are for use with air, engine and gear oils, hydraulic and
transmission fluids and antifreeze.
! WARNING
Use these reels only for the purpose for which they have
been designed. Do not exceed working pressure of reel or
hose. Do not use these reels for flammable, explosive or
corrosive applications. Do not modify any components and
use only original spare parts.
! CAUTION
Insure that incoming line pressure does not exceed rated
operating pressure of your model hose reel. Refer to
technical specifications on page 5 for pressure ratings.
! CAUTION
Note:
Hose spools off from reel in
a clockwise direction when
viewed from swivel side of
reel, (fig. 4).
Fig. 4
Possible Hose Guide
Configurations
Reels may be mounted on
ceiling, wall or tank (floor)
as shown in fig. 5a, 5b and
5c. Refer to instructions that follow to reposition guide arm.
To avoid damage to the reel, control handle or meter,
always hold onto hose while it is rewinding.
Fig. 5a
Fig. 5b
Before Installation:
1. Make sure mounting surface is sturdy enough to hold
the weight of the hose reel and take the stress of use. If
wall mounting, check both the inside and outside of wall
to make sure no electrical
Fig. 1
or plumbing lines will
interfere with installation.
2. It is recommended to install
a supply line shut-off valve
just before the connection
hose between product supply line and reel, fig. 1. This
allows easy maintenance of
reel, hose and control valve
or meter.
Fig. 2
3. Product service
labels (fig. 2)
are available for ease of installation.
Consult your Liquidynamics catalog or call
800-894-3572 for specific recommendations
and part numbers.
Tank, floor or wall mount, as
supplied by Liquidynamics.
Fig. 5c
Ceiling mount.
Page 2
Alternate wall mount.
Hose Guide
Re-Orientation
2. Remove ball stop by
removing 2 ea. Allen head
screws, fig. 7.
Fig. 6
Depending on the location of
reel installation, it may be
necessary or desirable to
change the orientation of
the hose guide arm, fig. 6.
This is easily accomplished
without release of spring
tension. Possible guide arm
orientations are shown in fig. 5, where 5a is the “normal”
position as supplied by Liquidynamics.
Fig. 5a; used for wall, floor and tank mounting
Fig. 5b; used for wall, floor and tank mounting
Fig. 5c; used for ceiling or wall mount
Fig. 7
Re-position guide arm
as shown in fig. 5 as
follows:
1. For position 5b and 5c
a.) Remove 4 ea. nuts and
bolts on each side of
guide arm, fig. 8.
b.) Rotate guide arm to 90°
to position shown in
fig. 5b.
c.) Reinstall 8 ea. nuts and
bolts securely.
d.) Reinstall ball stop at
desired location on hose.
1. Pull hose from reel until latch key is engaged to prevent
hose retraction.
Ball
Stop
Fig. 8
Nuts and
Bolts
Guide
Arm
Technical Specifications:
Model
88501-100L
Working
Pressure
870 PSI
Hose
Dia. ID
—
Hose
Length
—
Inlet
Connection
3/4” NPTF
Outlet
Connection
3/4” NPTF
Max Winding
Capacity
3/4 x 50’
Connecting
Hose Length
—
Shipping
Weight
62 lb
Model 88402, 88402DEF and
88403 Series Reels
24.75”
12.38”
27”
9.38”
24.5”
10.5”
Page 3
12”
10.88”
0.50
10.50”
1.
2.
3.
4.
5.
5A.
6.
7.
7A.
8.
9.
S45201
S45202
S45203
S45204
S45205
S45205DEF
S45206
S45207
S45207DEF
S45208
S45209
Hose Guide Kit, 88402, 88403 Reels
Hose Guide Kit, 88405 Reel
Hose Stop, 3/4” Hose
Hose Stop, 1” Hose
Seal Kit for 88402, 88403 and 88405 Reels
Seal Kit for 88402DEF Reels
Internal Swivel for 88402, 88403 and 88405 Reels
1” Inlet Swivel for 88402, 88403 and 88405 Reels
3/4” Swivel Inlet assembly for 88402DEF Reels
Retaining Ring Clip for 88402, 88403 and 88405 Reels
Pawl Kit, Includes pawl, stem and spring (88402,88403 and 88405 Reels)
2311 S. Edwards • Wichita, KS 67213 / TEL: 316-943-5477 • FAX: 316-943-4760 / TOLL FREE: 800-894-3572
E-MAIL: productinfo@liquidynamics.com / WEBSITE: www.liquidynamics.com
Rev. 6/15