DG-HR3400 - Smartlink Network Systems Ltd

DG-HR3400
300Mbps Wireless Broadband Home Router
User Manual
V2.0
2014-12-26
As our products undergo continuous development the specifications are subject to change without prior notice
DG-HR3400 User Manual
COPYRIGHT
Copyright 2015 by Smartlink Network Systems Ltd. All rights reserved. No part of
this publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or by any
means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise,
without the prior written permission of this company.
This company makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Any software described in this
manual is sold or licensed "as is". Should the programs prove defective following
their purchase, the buyer (and not this company, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves the
right to revise this publication and to make changes from time to time in the contents
thereof without obligation to notify any person of such revision or changes.
Trademarks:
DIGISOL™ is a trademark of Smartlink Network Systems Ltd. All other trademarks
are the property of the respective manufacturers.
Safety
This equipment is designed with the utmost care for the safety of those who install
and use it. However, special attention must be paid to the dangers of electric shock
and static electricity when working with electrical equipment. All guidelines of this
and of the computer manufacturer must therefore be allowed at all times to ensure the
safe use of the equipment.
2
DG-HR3400 User Manual
INDEX
1. Product Introduction..................................................................................................5
1-1 Introduction and Safety Information............................................................... 5
1-2 Safety Information...........................................................................................6
1-3 System Requirements.......................................................................................7
1-4 Package Contents............................................................................................7
2. Hardware Installation................................................................................................ 8
2-1 Get Familiar with your new wireless broadband router.................................8
2-1-1 Front Panel...........................................................................................8
2-2 Typical install................................................................................................ 10
2-3 Software Installation..................................................................................... 12
3. Quick Install Guide................................................................................................. 26
3-1 Connecting to wireless broadband router by web browser...........................26
3-2 Getting Started.............................................................................................. 29
3-3 Using Quick Setup.........................................................................................31
4. Configuring the Router............................................................................................37
4-1 Setup..............................................................................................................37
4-1-1 Wizard................................................................................................37
4-1-2 Local Network................................................................................... 38
4-1-3 Internet Setup.....................................................................................41
4-1-4 IPv6....................................................................................................44
4-1-5 Mode Settings.................................................................................... 49
4-2 Wireless......................................................................................................... 50
4-2-1 Wireless Basics.................................................................................. 51
4-2-2 MBSSID............................................................................................ 56
4-2-3 WPS................................................................................................... 58
4-2-4 Wireless Advanced.............................................................................59
4-2-5 Wireless Repeater.............................................................................. 61
4-2-6 WDS...................................................................................................62
4-3 Advanced....................................................................................................... 63
4-3-1 Access Control List............................................................................64
4-3-2 Port Triggering...................................................................................65
4-3-3 DMZ.................................................................................................. 66
4-3-4 URL Block......................................................................................... 67
4-3-5 IP/Port Filter...................................................................................... 68
4-3-6 MAC Filter.........................................................................................69
4-3-7 DOS Settings..................................................................................... 70
4-3-8 Dynamic DNS....................................................................................71
3
DG-HR3400 User Manual
4-3-9 QoS Setup.......................................................................................... 72
4-3-10 UPnP................................................................................................ 73
4-3-11 Routing.............................................................................................74
4-3-12 Virtual Server...................................................................................76
4-4 Maintenance..................................................................................................77
4-4-1 Reboot................................................................................................77
4-4-2 Firmware Upgrade............................................................................. 78
4-4-3 Backup/Restore..................................................................................79
4-4-4 Password............................................................................................ 80
4-4-5 Time and Date....................................................................................81
4-4-6 System Log........................................................................................ 82
4-4-7 Diagnostics-Ping................................................................................83
4-4-8 Diagnostics-Traceroute...................................................................... 84
4-5 Status.............................................................................................................85
4-5-1 Device Info........................................................................................ 85
4-5-2 Active Client Table............................................................................ 86
4-5-3 Statistics.............................................................................................86
4-5-4 IPv6....................................................................................................87
5. Appendix................................................................................................................. 88
6. Glossary...................................................................................................................90
4
DG-HR3400 User Manual
1. Product Introduction
1-1 Introduction and Safety Information
Thank you for purchasing DG-HR3400 300Mbps 802.11n Wireless Broadband Home
Router! DG-HR3400 is the best choice for Small office / Home office users, all
computers and network devices can share a single xDSL / cable modem internet
connection at high speed. Easy install procedures allow computer users to setup a
network environment in very short time - within minutes, even inexperienced users.
When the number of your computers and network-enabled devices grow, you can
also expand the number of network slots by simply connecting a hub or switch, to
extend the scope of your network.
All computers and IEEE 802.11b/g/n wireless-enabled network devices (including
PDA, cellular phone, game console and more) can connect to this wireless router
without additional cabling. With a compatible wireless card installed in your PC, you
can transfer files up to 300Mbps (transfer data rate).
Other features of this router include:














High Internet Access throughput.
Wireless speed up to 300Mbps.
Allows multiple users to share a single Internet line.
Shares a single Cable or xDSL internet connection.
Access private LAN servers from the internet.
Four wired LAN ports (10/100M) and one WAN port (10/100M).
Works with IEEE 802.11b/g/n wireless LAN devices.
Supports DHCP (Server/Client) for easy IP-address setup.
Supports multiple wireless modes like: AP, Client, Wireless Bridge and
Universal Repeater.
Advanced network and security features like: Special Applications, QoS, DMZ,
Virtual Servers, Access Control, Firewall.
Allows you to monitor the router’s status like: DHCP Client Log, System Log,
Security Log and Device/Connection Status.
Easy to use Web-based GUI for network configuration and management
purposes.
Remote management function allows configuration and upgrades from a remote
computer (over the Internet).
Provides Auto MDI / MDI-X function for all wired Ethernet ports.
5
DG-HR3400 User Manual
1-2 Safety Information
In order to keep the safety of users and your properties, please follow the safety
instructions as mentioned below:
1. This router is designed for indoor use only; DO NOT place this router outdoor.
2. DO NOT place this router close to a hot or humid area, like kitchen or bathroom.
Also, do not leave this router in the car during summer.
3. DO NOT pull any connected cable with force; disconnect it from the router first.
4. If you want to place this Router at a height or mount on the wall, please make sure
it is firmly secured. Falling from a height would damage the router and its
accessories and warranty will be void.
5. Accessories of this router, like antenna and power supply, are dangerous to small
children. KEEP THIS ROUTER OUT OF REACH OF CHILDREN.
6. The Router will get heated up when used for long time (This is normal and is not a
malfunction). DO NOT put this Access Point on paper, cloth, or other flammable
materials.
7. There’s no user-serviceable part inside the router. If you find that the router is not
working properly, please contact your dealer of purchase and ask for help. DO
NOT disassemble the router, warranty will be void.
8. If the router falls into water when it’s powered, DO NOT use your hands to pick it
up. Switch the electrical power off before you do anything, or contact an
experienced electrical technician for help.
9. If you smell something strange, or even see some smoke coming out from the
router or power supply, remove the power supply or switch the electrical power off
immediately, and call the dealer of purchase for help.
6
DG-HR3400 User Manual
1-3 System Requirements
 Notebook or desktop computer with network adapter (wired/wireless)
 Internet connection, provided by xDSL or cable modem with a RJ-45 Ethernet
port.
 Windows 98/ME/2000/XP/Vista
 Web browser (Microsoft Internet Explorer 4.0 or above, Netscape Navigator 4.7
or above, Opera web browser, or Safari web browser).
 An available AC power socket (100 – 240V, 50/60Hz)
1-4 Package Contents
Before you start using this router, please check if there’s anything missing in the
package, and contact your dealer of purchase to claim for missing items:






DG-HR3400 Wireless Broadband Home Router
Power adapter (5V DC, 1A)
Rubber feet (4 Nos.)
Quick Installation Guide
Installation Guide CD (includes User Manual, QIG &Utility)
Patch Cord (1 No.)
7
DG-HR3400 User Manual
2. Hardware Installation
2-1 Get Familiar with your new wireless broadband router
2-1-1 Front Panel
LED Name
LED Status Indication
Power (PWR)
On
Router is switched on and correctly powered.
On
WAN port is connected.
Off
WAN port is not connected.
Blinking
WAN activity (transferring or receiving data).
WAN
8
DG-HR3400 User Manual
LAN(1-4)
WLAN
WPS
On
LAN port is connected.
Off
LAN port is not connected.
Blinking
LAN activity (transferring or receiving data).
On
Wireless network is switched on.
Off
Wireless network is switched off.
Blinking
Wireless LAN activity (transferring or receiving data).
On
A wireless device has been successfully added to the
network by WPS function.
Off
WPS process is not initiated.
Blinking
A wireless device is connecting to the network by
WPS function.
9
DG-HR3400 User Manual
2-1-2 Back Panel
Interfaces
Antennas
Power on/off
button
Description
These antennas are 5dBi dipole antennas.
Press this button to power on/off the router.
LAN (1 – 4)
The Power socket is where you will connect the power adapter.
Please use the power adapter provided with this Wireless Router.
Local Area Network (LAN) ports 1 to 4.
WPS
Press this button for more than 5 seconds to initiate WPS.
Power
Reset
WAN
Reset the router to factory default settings (clear all settings).
Press this button and hold for 5 seconds to restore all settings to
factory defaults.
Wide Area Network (WAN / Internet) port.
10
DG-HR3400 User Manual
2-2 Typical install
Hardware Installation:
Please follow the below mentioned instructions to build the network connection
between your new WIRELESS router and your computers, network devices:
1. Connect your xDSL / cable modem to the WAN port of the router by an Ethernet
cable.
2. Connect all your computers, network devices (switch / hub) to the LAN port of
the router.
11
DG-HR3400 User Manual
3. Connect the power adapter (5V DC / 1A) to the wall socket, and then connect it
to the ‘Power’ socket of the router.
4. Please check all LEDs on the front panel. Power LED ‘PWR’ should be steadily
ON, WAN and LAN LEDs should be ON. Check if the computer/network device
connected to the respective port of the router is powered ON and correctly
connected. If power LED ‘PWR’ is not ON, or any LED you expected is not ON,
please recheck the cabling.
12
DG-HR3400 User Manual
2-3 Software Installation

Insert the Setup CD into your CD-ROM drive of notebook/desktop computer.

Explore the CD and execute the “AutoRun.exe” file. Below given screen will
appear. Click 'Start' to Continue.
13
DG-HR3400 User Manual

Connect one end of a network cable to the WAN port of the router and the
other end to the DSL/Cable modem. Click ‘Next’ to continue.

Connect one end of the provided network cable to one of the LAN ports (1~4)
of the router and the other end to your computer. Click ‘Next’ to continue
with the installation.
14
DG-HR3400 User Manual

Power on the Router. It will take approximately 30 seconds for the router to
boot up completely. Click ‘Next’ to continue with the installation.

Ensure the normal indication of all LED’s on the router. If not, try the above
steps again else click ‘Next’ to continue.
15
DG-HR3400 User Manual

Enter the Router’s password to log in to the Router. The default password is
“1234”. It is recommended to change the router’s password to protect it from
being accessed by other users. If you do not wish to change the current
password, you can leave “New Password” and “Confirm New Password”
fields blank. Click ‘Log in’ to continue.

Please select the internet connection type. Click ‘Next’ to continue.
NOTE: The steps mentioned till here are the common steps to be
followed for all the three modes. Following steps below
describe how to configure the respective modes.
16
DG-HR3400 User Manual
PPPoE (DSL users)

Choose PPPoE. (Point to Point Protocol over Ethernet) If your ISP uses a
PPPoE connection you will be provided with a username and password. This
option is typically used for DSL services.

Once the user name and password is entered click on ‘Next’, the screen
shown below will appear. Click on ‘Next’.
17
DG-HR3400 User Manual

Enter the ‘SSID’ and click on ‘Next’.

Configure the wireless security. Enter the security mode i.e. either ‘None’ or
‘WPA2 Mixed’ and click on ‘Next’.
18
DG-HR3400 User Manual

The screen as shown below will appear. Click on ‘Finish’.

Lastly, the router will reboot as shown below.
19
DG-HR3400 User Manual
DHCP (Cable Modem users)

Select DHCP Client to obtain IP Address information automatically from your
ISP. Click on ‘Next’.

The screen shown below will appear. Click on ‘Next’.
20
DG-HR3400 User Manual

Below mentioned screen will appear. Click on ‘Next’.

Enter the ‘SSID’ and click on ‘Next’.
21
DG-HR3400 User Manual

Configure the wireless security. Enter the security mode i.e. either ‘None’ or
‘WPA2 Mixed’ and click on ‘Next’.

Following screen will appear. Click on ‘Finish’.
22
DG-HR3400 User Manual

Lastly, the router will reboot as shown below.
Static IP (Cable Modem users)

Select Static IP Address if all the Internet port’s IP information is provided to
you by your ISP. You will need to enter in the IP address, subnet mask,
gateway address and DNS address provided to you by your ISP. Each IP
address entered in the fields must be in the appropriate IP form, which are
four octets separated by a dot (x.x.x.x). The Router will not accept the IP
address if it is not in this format. Click on ‘Next’.
23
DG-HR3400 User Manual

The screen shown below will appear. Click on ‘Next’.

Enter the ‘SSID’ and click on ‘Next’.
24
DG-HR3400 User Manual

Configure the wireless security. Enter the security mode i.e. either ‘None’ or
‘WPA2 Mixed’ and click on ‘Next’.

You can view the information about the wireless configuration in the next
screen. Click ‘Finish’ to save your current settings and reboot the router.
25
DG-HR3400 User Manual
3. Quick Install Guide
3-1 Connecting to wireless broadband router by web browser
After the network connection is setup, next step is to setup the router with proper
network parameters, so it can work properly in your network environment.
Please use the web browser to configure the router. A computer with wired Ethernet
connection to the router is required for this first-time configuration.
Before you start to configure the router (default IP 192.168.2.1), please configure the
IP address of the computer in the same network class as that of the router.
Set the Network Configurations:
1. On your computer desktop right click "My Network Places" and select
"Properties".
2. Right click "local Area Network Connection" and select "Properties".
26
DG-HR3400 User Manual
3. Select "Internet Protocol (TCP/IP)" and click "Properties".
4. Select "Obtain an IP address automatically" or select "Use the following IP
address(S)".
A. Select "Obtain an IP address automatically" and "Obtain DNS server
address automatically". Click "OK".
27
DG-HR3400 User Manual
B. “Use the following IP address (S)"
IP Address: 192.168.2.XXX (XXX is a number from 2~254)
Subnet Mask: 255.255.255.0
Gateway: 192.168.2.1
DNS Server: You need to input the DNS server address provided by your ISP.
Otherwise, you can use the Router's default gateway as the DNS proxy server.
Click "OK" to save the configurations.
Click "OK" to save the configurations.
28
DG-HR3400 User Manual
3-2 Getting Started
Connecting the router’s management interface by web browser:
After you assign an IP address to the computer, open the web browser, and type the
IP address of the router in the address bar as ‘http://192.168.2.1’.
The following message should be shown:
Please input user name and password in the field respectively, default user name is
‘admin’, and default password is ‘1234’, then press ‘Login’ button, and you can see
the web management interface of this router:
29
DG-HR3400 User Manual
NOTE: If you can’t see the web management interface, and you’re
being prompted to input user name and password again, it
means you didn’t input username and password correctly.
Please retype user name and password again.
TIP: This page shows the current status and some basic settings of
the device.
30
DG-HR3400 User Manual
3-3 Using Quick Setup
This router provides a ‘Quick Setup’ procedure, which will help you to complete all
required settings you need to access the Internet in very short time. Please follow the
instructions mentioned below to complete the ‘Quick Setup’:
Please go to Quick Setup menu by clicking ‘Setup’ button.
And the following message will be displayed:
Click the “Next” button to continue.
Please follow the steps and complete the router configuration.
31
DG-HR3400 User Manual
Step 1 Setup WAN Connection Type:
Below given ‘WAN Connection Type’ screen will appear.
Please choose the broadband (Internet connection) type you’re using in this page.
There are three types of Internet connection, PPPoE, Dynamic IP and Static IP.
If you’re not sure, please contact your Internet service provider. A wrong Internet
connection type will cause connection problem, and you will not be able to connect
to the internet.
If you want to go back to previous step, please press ‘Back’ button.
NOTE:
Some service providers use ‘DHCP’ (Dynamic Host
Configuration Protocol) to assign IP address to your router. In
this case, you can choose ‘Dynamic IP’ as Internet connection
type.
32
DG-HR3400 User Manual
Setup procedure for ‘PPPoE’:
Choose PPPoE. (Point to Point Protocol over Ethernet) If your ISP uses a PPPoE
connection it will provide you with a username and password. This option is typically
used for DSL services. Below given screen will be displayed.
Here is the description of every setup item:
Parameter
User Name
Password
Confirm
Password
Description
Please input user name assigned by your Internet service
provider here.
Please input the password assigned by your Internet service
provider here.
Re-enter the password in this field for confirmation.
When you finish with all settings, press ‘Next’; if you want to go back to previous
menu, click ‘Back’.
Setup procedure for ‘Dynamic IP’:
Select Dynamic IP to obtain IP Address information automatically from your ISP.
Usually Cable Modem and the router will automatically obtain an IP address from the
DHCP server.
33
DG-HR3400 User Manual
Setup procedure for ‘Static IP’:
Select Static IP Address if IP information is provided to you by your ISP. You will
need to enter in the IP address, subnet mask, gateway address and DNS address
provided to you by your ISP. Each IP address entered in the fields must be in the
appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router
will not accept the IP address if it is not in this format. Below given screen will be
displayed.
Here is the description of every setup item:
Parameter
IP address
Subnet Mask
Default Gateway
Primary DNS
Secondary DNS
Description
Please input IP address assigned by your service provider.
Please input subnet mask assigned by your service provider
Please input the default gateway assigned by your service
provider.
Please input the DNS IP address in dotted-decimal notation
provided by your ISP.
Please input another DNS IP address in dotted-decimal notation
provided by your ISP.
NOTE: You must use the addresses provided by your Internet service
provider, wrong setting value will cause connection problem.
When you finish with all settings, press ‘Next’; if you want to go back to previous
menu, click ‘Back’.
34
DG-HR3400 User Manual
Step 2 Setup Wireless:
Below given ‘Wireless’ screen will appear.
Here is the description of every setup item:
Parameter
Description
Disable the wireless The wireless radio of this Router can be enabled or disabled
radio
to allow wireless stations access.
SSID
This is the name of wireless network. Input the SSID name
that your wireless ISP has provided you with.
Channel
This is the radio frequency used to transmit and receive the
wireless signal. The wireless devices in the same network
should follow the same setting. Select the channel
designated by your wireless ISP.
Mode
Select the desired mode. The default setting is 2.4GHz
(B+G+N).
Channel Width
Select any channel width from the pull-down list. The
35
DG-HR3400 User Manual
Wireless Security
default setting is Auto 20/40M, which can adjust the
channel width for your clients automatically.
If the access point enables wireless security, you have to
follow the same settings in order to access the access point.
When you finish with all settings, press ‘Next’; if you want to go back to previous
menu, click ‘Back’.
Step 3 Finish the Quick Setup:
Below given ‘Finish’ screen will appear.
You can click the “Finish” button to finish the Quick Setup; if you want to go back to
previous menu, click ‘Back’.
36
DG-HR3400 User Manual
4. Configuring the Router
This section will show each Web page’s key functions and the configuration way.
After your successful login, you will see the five main menus on the top of the
Web-based utility. On the right, there are corresponding explanations and
instructions.
4-1 Setup
Click ‘Setup’ menu on the top of the web management interface, and the following
message will be displayed on your web browser:
There are four submenus under the Setup menu: Wizard, Local Network, Internet
Setup, Mode Settings. Click any of them, and you will be able to configure the
corresponding function.
4-1-1 Wizard
If you are new to networking and have never configured a router before, click on
Wizard and the router will guide you through a few simple steps to get your network
up and running.
Choose menu “Setup→Wizard”, below given screen will be displayed.
37
DG-HR3400 User Manual
For details please refer to 3.3 Using Quick Setup on above.
4-1-2 Local Network
These are the settings of the LAN (Local Area Network) interface for the router.
Choose menu “Setup→Local Network”, below given screen will be displayed.
This page is used to configure the LAN interface of your Wireless Router. Here you
may change the setting for IP address, subnet mask, etc.
This page can be used to configure the DHCP mode: None or DHCP Server.
(1) Enable the DHCP Server if you are using this device as a DHCP server. This page
38
DG-HR3400 User Manual
lists the IP address pools available to hosts on your LAN. The device distributes
numbers in the pool to hosts on your network as they request Internet access.
If you choose "None", then the router will do nothing when the hosts request an IP
address.
(2) This page lists the fixed IP/MAC address on your LAN. The device distributes
the number configured to hosts on your network as they request Internet access.
LAN Interface Setup:
Here is the description of every setup item:
Parameter
IP address
Subnet Mask
Description
Please input the IP address of this router.
Please input the subnet mask of this network.
DHCP Server Settings:
These settings are only available when ‘DHCP Server’ in ‘LAN IP’ section is
‘Enabled’, and here is the description of every setup item.
Parameter
DHCP Mode
Description
IP Pool Range
These two IP values (from and to) define a range of IP addresses
that the DHCP Server uses when assigning addresses to
computers and devices on your Local Area Network. Any
Enable or Disable the DHCP Server.
39
DG-HR3400 User Manual
address that does not fall in this range are not managed by the
DHCP Server; these could, therefore, be used for manually
configured devices or devices that cannot use DHCP to obtain
network address details automatically.
Max Lease Time The amount of time that a computer may have an IP address
before it is required to renew the lease. The lease functions, just
as a lease on an apartment would. The initial lease designates
the amount of time before the lease expires. If the tenant wishes
to retain the address when the lease is expired then a new lease
is established. If the lease expires and the address is no longer
needed then another tenant may use the address.
Domain Name
Domain name for the dhcp server scope.
DNS Server
DNS Server address for the dhcp server scope.
DHCP Static IP Configuration:
If you need to assign static IP for your computer or device on the local area network,
configure static IP with the MAC address.
Here is the description of every setup item:
Parameter
IP address
Description
Mac Address
After you enter MAC address and IP address pair,
click this button to add the pair to static DHCP
leases table.
The IP address to be configured for your computer
or device on the local area network. For example,
192.168.2.2.
After you clicked ‘Add’, the MAC address and IP address mapping will be added
to ‘DHCP Static IP Table’ section.
40
DG-HR3400 User Manual
4-1-3 Internet Setup
This page is used to configure the parameters for Internet network which connects to
the WAN port of your Access Point. Here you may change the access method to static
IP, DHCP client or PPPoE by clicking the item value of WAN Access type.
Choose menu “Setup→Internet Setup”, below given screen will be displayed.
Setup procedure for ‘Static IP’:
41
DG-HR3400 User Manual
Here is the description of every setup item:
Parameter
IP Address
Description
Please input the IP address assigned by your service provider.
Subnet Mask
Please input the subnet mask assigned by your service
provider
Please input the IP address of the gateway provided by your
service provider.
Please input the MTU value of your network connection here.
If you don’t know, you can use default value.
Please input the IP address of DNS servers provided by your
service provider.
Default Gateway
MTU Size
DNS Servers
1/2/3
Setup procedure for ‘DHCP Client’:
Here is the description of every setup item:
Parameter
Host Name
MTU Size
Attain DNS
Automatically
Set DNS Manually
Description
Please input the host name of your computer. This is
optional, and is only required if your service provider
asks you to do so.
Please input the MTU value of your network connection
here. If you don’t know, you can use default value.
If your ISP specifies a DNS server IP address for you,
click the checkbox.
Enter the DNS IP address manually provided by your
ISP.
42
DG-HR3400 User Manual
Setup procedure for ‘PPPoE’:
Here is the description of every setup item:
Parameter
User Name
Password
Service Name
MTU Size
Connection Type
Description
Please input user name assigned by your Internet service provider
here.
Please input the password assigned by your Internet service
provider here.
Please give a name to this Internet service, this is optional.
Please input the MTU value of your network connection here. If
you don’t know, you can use default value.
Please select the connection type of Internet connection you wish
to use.
Continuous – The connection will be kept always On. If the
connection is interrupted, the router will re-connect
automatically.
Connect On-Demand – Only connect when you want to surf the
Internet. “Idle Time Out” is set to stop the connection when the
network traffic is not sending or receiving after an idle time.
Attain DNS
Automatically
Manual – After you have selected this option, you will see the
“Connect” button and “Disconnect” button, click “’Connect” and
the router will connect to the ISP. If you want to stop the
connection, please click “Disconnect” button.
If your ISP specifies a DNS server IP address for you, click the
check box.
43
DG-HR3400 User Manual
Set DNS
Manually
Enter the DNS IP address manually provided by your ISP.
MAC Clone:
You can configure the MAC address of the WAN.
4-1-4 IPv6
In this section the IPv6 configuration can be done. The WAN and LAN parameters
can be defined using this section.
44
DG-HR3400 User Manual
Static IPv6
In Static IPv6 mode, user can set the IPv6 IP address of the WAN port.
Parameter
Description
IPv6 address( WAN)
Subnet Prefix Length
Default Gateway
Primary DNS address
Secondary DNS address
LAN IPv6 Address
Enable Autoconfiguration
Autoconfiguration Type
Enter the IPv6 address for WAN port.
Enter the Subnet Prefix length here.
Enter the IPv6 address of the default gateway.
Enter the preferred IPv6 DNS address.
Enter the secondary IPv6 DNS address.
Enter the Static LAN IPv6 address of the router.
Enable or Disable the Auto configuration (DHCP IPv6).
Select the Type of Autoconfiguration from the Dropdown
45
DG-HR3400 User Manual
list.
Router Advertisement
Lifetime
Set the value of Router advertisement duration.
SLAAC/DHCPv6
In this section we can set the WAN parameters as per DHCP IPv6.
46
DG-HR3400 User Manual
PPPoE
Parameter
Username
Password
Service Name
MTU Size
Connection Type
Description
Type the PPPoE username provided by ISP
Type the PPPoE password provided by ISP
Type the Service name provided by ISP (optional)
Type the MTU size ( Defined by ISP)
Select the connection type.
47
DG-HR3400 User Manual
4-1-5 Mode Settings
This page is used to configure mode.
Choose menu “Setup→Mode Settings”, below given screen will be displayed.
Here is the description of every setup item:
Parameter
Bridge Mode
Router Mode
Description
The device works as a bridge. All ethernet wired ports and
wireless ports are bridged together.
The device works as a router. It can access to the Internet
by Static IP/DHCP Client/PPPoE.
NOTE: The device would reboot if you change the mode.
48
DG-HR3400 User Manual
4-2 Wireless
Click ‘Wireless’ menu on the top of web management interface, and the following
message will be displayed on your web browser:
There are six submenus under the Wireless menu: Wireless Basics, MBSSID, WPS,
Wireless Advanced, Wireless Repeater, and WDS. Click any of them, and you will
be able to configure the corresponding function.
4-2-1 Wireless Basics
This page is used to configure the parameters for wireless LAN clients which may
connect to your Access Point. Here you may change wireless encryption settings as
well as wireless network parameters.
Choose menu “Wireless→Wireless Basics”, below given screen will be displayed.
49
DG-HR3400 User Manual
Setup procedure for AP:
Here is the description of every setup item:
Parameter
Enable SSID
Broadcast
Description
Enable Wireless
Isolation
If checked, the wireless client under this SSID can only access
internet and it can`t access other wireless clients even under the
same SSID, Ethernet clients or this device. Other clients can`t
access the wireless client, either.
Name(SSID)
Enter a value of up to 32 alphanumeric characters. The same
name (SSID) must be assigned to all wireless devices in your
network. The default SSID is "DIGISOL”, but we strongly
recommend that you change your network`s name (SSID) to a
different value. This value is case-sensitive. For example, SSID
is not the same as SsiD.
If Enabled, the Wireless Access Point will broadcast its name
(SSID) to all Wireless Stations. Stations which have no SSID (or
a null value) can then adopt the correct SSID for connections to
this Access Point.
50
DG-HR3400 User Manual
Mode
Select the wireless mode you want to use. The options are:






802.11b mode. With a maximum speed of up to 11 Mbps.
802.11g mode. With a maximum speed of up to 54 Mbps.
802.11n mode. The band width is 20M, with a maximum
speed of up to 130 Mbps (short preamble, with a maximum
speed of up to 150 Mbps); The band width is 40M, with a
maximum speed of up to 270 Mbps (short preamble, with a
maximum speed of up to 300 Mbps).
802.11b/g mode. With a maximum speed of up to 54 Mbps.
802.11n/g mode. The band width is 20M, with a maximum
speed of up to 130 Mbps (short preamble, with a maximum
speed of up to 150 Mbps); The band width is 40M, with a
maximum speed of up to 270 Mbps (short preamble, with a
maximum speed of up to 300 Mbps).
802.11b/g/n mode. The band width is 20M, with a maximum
speed of up to 130 Mbps (short preamble, with a maximum
speed of up to 150 Mbps); The band width is 40M, with a
maximum speed of up to 270 Mbps (short preamble, with a
maximum speed of up to 300 Mbps).
Channel
This field determines which operating frequency will be used. It
should not be necessary to change the wireless channel unless
you notice interference problems with another nearby access
point.
Band Width
Select any channel width from the pull-down list. The default
setting is Auto 20/40M, which can adjust the channel width for
your clients automatically.
Security
Options
There are six wireless security modes supported by the Router:
WEP, WPA-PSK [TKIP], WPA-PSK [AES], WPA2-PSK [AES],
WPA2-PSK [TKIP], WPA-PSK/WPA2-PSK AES.
51
DG-HR3400 User Manual
Setup procedure for Client:
In this mode, you can connect the router to Ethernet devices such us TV, Game player,
HDD & DVD to enable the Ethernet device to be a wireless station and join to a
wireless network through an access point or AP router.
Here is the description of every setup item:
Parameter
Description
SSID of AP
This is the name of wireless network. Input the SSID name that
your wireless ISP has provided you with.
Site Survey
Click ‘Site Survey’ button, then a “Wireless Site Survey Table”
will pop up. It will list all available access points nearby. Select
the access point designated by your wireless ISP in the table and
the router will join wireless network through this access point.
Security
Options
If the access point enables wireless security, you have to follow
the same settings in order to access the access point.
52
DG-HR3400 User Manual
Setup procedure for WDS or WDS+AP:
In this mode, you can expand the scope of network by combining up to four other
access points together.
Here is the description of every setup item:
Parameter
Enable SSID
Broadcast
Enable Wireless
Isolation
Name(SSID)
Mode
Channel
Band Width
Description
If Enabled, the Wireless Access Point will broadcast its
name (SSID) to all Wireless Stations. Stations which have
no SSID (or a null value) can then adopt the correct SSID
for connections to this Access Point.
If checked, the wireless client under this SSID can only
access internet and it can’t access other wireless clients
even under the same SSID, Ethernet clients or this device.
Other clients can’t access the wireless client, either.
Input the SSID of your wireless router, the setting should
be the same with other wireless routers for the
convenience of roaming.
Select the mode you want to use; all the wireless routers
must use the same setting.
Select the channel you want to use; all the wireless routers
must use the same setting.
Select any channel width from the pull-down list. The
53
DG-HR3400 User Manual
Security Options
default setting is Auto 20/40M, which can adjust the
channel width for your clients automatically.
If the wireless bridge point enables wireless security, you
have to follow the same settings in order to access the
access point.
4-2-2 MBSSID
Here we provide several guest networks for your guests to use your router to surf the
Internet temporary. You can configure your SSID, security options and so on. Guests
can only access your router if you enable your guest network.
Choose menu “Wireless→MBSSID”, below given screen will be displayed.
Here is the description of every setup item:
Parameter
Network Profiles
Description
You can click radio button of each profile to check detail info
or change settings of each profile. The table is a brief
summary of how many profiles you can create, it provides
profile number, SSID of this profile, Security type of this
profile, this guest wireless network is Enabled or Not, and the
SSID will be displayed or not.
54
DG-HR3400 User Manual
Enable Guest
Network
Enable SSID
Broadcast
Allow Guest to
access My Local
Network
Enable Wireless
Isolation
Guest Wireless
Network Name
(SSID)
Security Options
If this feature is checked, then this guest network is enabled.
You and your visitors can connect to your network via the
SSID of this profile.
If Enabled, the Wireless Access Point will broadcast its name
(SSID) to all Wireless Stations. Stations which have no SSID
(or a null value) can then adopt the correct SSID for
connections to this Access Point.
If Unchecked, any user that connects to this SSID can only
access internet, but can not access gateway management UI,
such as Web Server, Telnet, etc. .All clients in this SSID are
not allowed to access clients of other SSIDs and Ethernet
network.
If Checked, any user who connects to this SSID can access not
only internet but also local networks of this wireless router
like users in primary SSID.
If checked, the wireless clients under this SSID can’t access
other wireless clients under the same SSID.
If unchecked, the wireless client under this SSID can access
other wireless clients under the same SSID.
Enter a value of up to 32 alphanumeric characters. The same
Name (SSID) must be assigned to all wireless devices in your
network. The default SSID is SSID-N, N is profile number,
but we strongly recommend that you change your network`s
Name (SSID) to a different value. This value is also
case-sensitive. For example, SSID is not the same as SsiD.
 None - no data encryption
 WEP - Wired Equivalent Privacy, use WEP 64- or 128-bit
data encryption
Note: Wi-Fi Protected Setup function is disabled when the
security setting is WEP with Shared-Key authentication
 WPA-PSK [TKIP] - Wi-Fi Protected Access with
Pre-Shared Key, use WPA-PSK standard encryption with
TKIP encryption type
 WPA2-PSK [AES] - Wi-Fi Protected Access version 2 with
Pre-Shared Key, use WPA2-PSK standard encryption with
the AES encryption type
 WPA-PSK [AES] + WPA2-PSK [AES] - Allow clients
using either WPA-PSK [AES] or WPA2-PSK [AES]
To achieve the best performance with 11N wireless adapters
under robust security network, we recommend that you change
your network’s security option to WPA2-PSK.
55
DG-HR3400 User Manual
4-2-3 WPS
Through this process, you can easily add wireless clients to the network without the
need for any specific configuration, such as SSID, security mode or password.
Choose menu “Wireless→WPS”, below given screen will be displayed.
WPS (WiFi Protected Setup) is easy way to connect to a wireless router.
To use the wizard to add a wireless client to WPS-enabled wireless router, the client
must support WPS.
Check the user manual or the box of the wireless client to confirm whether it supports
the WPS.
If the wireless client does not support WPS, you must configure it manually.
Click the “Next” button to continue.
You can add wireless client by PIN mode. If you use PIN mode, you should input
client PIN code. Meanwhile you should start client WPS process. You can find client
PIN code on client manager.
56
DG-HR3400 User Manual
Here is the description of every setup item:
Parameter
Description
Entry PIN of wireless The length of PIN is limited to four or eight numeric
NIC
digits. If the AP and Station input the same PIN and click
“Start PIN” button in two minutes, they will establish
connection and setup their security key.
4-2-4 Wireless Advanced
This page helps you to setup advanced wireless features, include Fragment Threshold
etc.
Choose menu “Wireless→Wireless Advanced”, below given screen will be
displayed.
57
DG-HR3400 User Manual
Here is the description of every setup item:
Parameter
Description
Enable Wireless
Check this box to enable the Router’s wireless features; uncheck
to disable it.
Fragment
Threshold
Used to fragment packets which help improve performance in the
presence of radio frequency (RF) interference.
RTS Threshold
Determines the packet size of a transmission through the use of the
router to help control traffic flow.
Preamble Type
This is the length of the CRC (Cyclic Redundancy Check) block
for communication between the router and wireless clients. High
network traffic areas should select Short preamble type.
Radio Power
(percent)
You can choose the transmission power of the radio signal. The
default one is 100%. It is recommended to choose the default
value 100%.
HT20/40
Coexistence
Enable this option to reduce interference from other wireless
networks in your area. If the channel width is operating at 40MHz
and there is another wireless network's channel over-lapping and
causing interference, the router will automatically change to
20MHz.
ACL Set up
You can specify what kind of service should be enabled in WAN on this page.
Packets available in the list or from IP specified can enter the AP router.
58
DG-HR3400 User Manual
4-2-5 Wireless Repeater
This page is used to configure the parameters for wireless repeater.
Choose menu “Wireless→Wireless Repeater”, below given screen will be
displayed.
DHCP server will automatically shut down if relay mode is enabled (DHCP server
will be enabled if relay mode is disabled). We recommend that the computer's IP
address and DNS address is set to automatically obtain. You need to manually set the
IP address of the computer if you want to access the device, while your PC got IP
address from the upstream AP.
In order to complete these settings, please follow the steps below:
 Click “Site Survey”. Sites surveyed will be displayed in the list below. Select
one item, and click “Next”.
 Setup the wireless security. Turn on WEP or WPA by using Encryption Keys
which could prevent any unauthorized access to your wireless network.
 Click “Finish” to save the configuration.
59
DG-HR3400 User Manual
4-2-6 WDS
Wireless Distribution System uses wireless media to communicate with other APs,
like the Ethernet does. To do this, you must set these APs in the same channel and set
MAC address of other APs which you want to communicate with in the table and
then enable the WDS. This page also allows you to setup the wireless security for
WDS. When enabled, you must make sure each WDS device has adopted the same
encryption algorithm and Key.
Choose menu “Wireless→WDS”, below given screen will be displayed.
Here is the description of every setup item:
Parameter
MAC Address
Description
Comment
WDS Security Setup
You can add some comment for this item.
All base stations in a wireless distribution system must
be configured to use the same radio channel, method of
encryption (none, WEP, TKIP or AES) and the same
encryption keys.
Input the MAC address of other wireless routers.
60
DG-HR3400 User Manual
4-3 Advanced
Click ‘Advanced’ menu on the top of web management interface, and the following
message will be displayed on your web browser:
There are twelve submenus under the Advanced menu: Access Control List, Port
Triggering, DMZ, URL Block, IP/Port Filter, MAC Filter, DOS Settings,
Dynamic DNS, QoS Setup, UPnP, Routing, Virtual Server. Click any of them, and
you will be able to configure the corresponding function.
61
DG-HR3400 User Manual
4-3-1 Access Control List
You can specify what kind of service should be enabled in WAN on this page.
Packets available in the ACL list or from IP specified can enter the AP Router.
Choose menu “Advanced→Access Control List”, below given screen will be
displayed.
Here is the description of every setup item:
Parameter
Description
WAN Setting
Select WAN or a specific IP address range.
Services Allowed
Specify what kind of service should be enabled in WAN.
62
DG-HR3400 User Manual
4-3-2 Port Triggering
Entries in this table are used to restrict certain types of data packets from your local
network to Internet through the Gateway. Use of such filters can be helpful in
securing or restricting your local network.
Choose menu “Advanced→Port Triggering”, below given screen will be displayed.
Here is the description of every setup item:
Parameter
Description
Nat Port Trigger
If you want to enable Nat Port Trigger function, please
select ‘Enable’; otherwise please select ‘Disable’.
63
DG-HR3400 User Manual
Usual Application Name
You can choose the type for the Usual Application
Name on the pull-down list.
User-defined Application
Name
Enter an application name for the rule.
Start Match Port - End
Match Port
The port range for outgoing traffic. An outgoing
connection using this port will “Match” this rule.
Trigger Protocol
The protocol used for Trigger Ports, either TCP, UDP,
or TCP/UDP.
Start Relate Port - End
Relate Port
The port range used by the remote system when it
responds to the outgoing request. A response using one
of these ports will be forwarded to the PC that
triggered this rule.
Open Protocol
The protocol used for Incoming Ports Range, either
TCP or UDP, or TCP/UDP.
Nat Type
Incoming mode will allow inbound traffic to specific
incoming port. Outgoing mode will allow outbound
traffic to specific outgoing port.
4-3-3 DMZ
A Demilitarized Zone is used to provide Internet services without sacrificing
unauthorized access to its local private network. Typically, the DMZ host contains
devices accessible to Internet traffic, such as Web (HTTP) servers, FTP servers,
SMTP (e-mail) servers and DNS servers.
Choose menu “Advanced→DMZ”, below given screen will be displayed.
64
DG-HR3400 User Manual
Here is the description of every setup item:
Parameter
Description
Enable DMZ
Check this box to enable DMZ function, uncheck this box to
disable DMZ function.
DMZ Host IP
Address
Enter DMZ host IP Address. Specify the LAN IP address of
the PC on which you want to have unrestricted Internet
communication.
4-3-4 URL Block
This page is used to configure the filtered keyword. Here you can add/delete filtered
keyword.
Choose menu “Advanced→URL Block”, below given screen will be displayed.
Here is the description of every setup item:
Parameter
Description
URL Blocking Capability If you want to enable URL Blocking Capability
function, please select ‘Enable’; otherwise please
select ‘Disable’.
Keyword
Enter the keyword that you want to block.
65
DG-HR3400 User Manual
4-3-5 IP/Port Filter
Entries in this table are used to restrict certain types of data packets from your local
network to Internet through the Gateway. Use of such filters can be helpful in
securing or restricting your local network.
Choose menu “Advanced→IP/Port Block”, below given screen will be displayed.
Here is the description of every setup item:
Parameter
Default Action
Status
Protocol
Rule Action
Direction
Source IP Address
Dest IP Address
Description
Select Deny or Permit.
The protocol used to filter, either IP, ICMP, TCP, or UDP.
Select Permit or Deny.
You can choose the type for the IP/Port Filter on the
pull-down list.
Specify the source IP address that will be affected by this
rule.
Specify the destination IP address that will be affected by
this rule.
66
DG-HR3400 User Manual
SPort
DPort
Enable
Specify the source port range that will be affected by this
rule.
Specify the destination port range that will be affected by
this rule.
Check this box to to enable the IP/Port Filter features;
uncheck to disable it.
4-3-6 MAC Filter
Entries in this table are used to restrict certain types of data packets from your local
network to Internet through the Gateway. Use of such filters can be helpful in
securing or restricting your local network.
Choose menu “Advanced→MAC Filter”, below given screen will be displayed.
67
DG-HR3400 User Manual
Here is the description of every setup item:
Parameter
Default Policy
Description
Direction
You can choose the type for the MAC Filter on the pull-down
list.
Select Deny or Permit.
Specify a source MAC address.
Specify a destination MAC address.
Action
Source MAC
Destination MAC
Select Deny or Permit.
4-3-7 DOS Settings
A "denial-of-service" (DoS) attack is characterized by an explicit attempt by hackers
to prevent legitimate users of a service from using that service.
Choose menu “Advanced→DOS Settings”, below given screen will be displayed.
68
DG-HR3400 User Manual
Here is the description of every setup item:
Parameter
Description
Enable Dos
Prevention
Check this box to enable the Dos Prevention features;
uncheck to disable it.
Enable source IP
blocking
The Router will block the IP Address of source which sends
the DoS attack for specified time.
4-3-8 Dynamic DNS
This page is used to configure the Dynamic DNS address from Oray, No-IP,
DynDNS.org and TZO. Here you can Add/Remove to configure Dynamic DNS.
Choose menu “Advanced→Dynamic DNS”, below given screen will be displayed.
Here is the description of every setup item:
Parameter
Description
Enable
Check this box to enable the DDNS features; uncheck to
disable it.
69
DG-HR3400 User Manual
DDNS Provider
Choose your DDNS Provider from the drop down menu.
Host Name
Enter the Host Name that you have registered with your
DDNS service provider.
Username
Enter the Username for your DDNS account.
Password
Enter the Password for your DDNS account.
4-3-9 QoS Setup
This page is used to configure QoS bandwidth and rules.
Choose menu “Advanced→QoS Setup”, below given screen will be displayed.
Here is the description of every setup item:
Parameter
Up Stream
Description
Down Stream
Auto Traffic
Shaping
The download speed through the WAN port.
Check this box to enable the Auto Traffic Shaping features;
uncheck to disable it.
The upload speed through the WAN port.
70
DG-HR3400 User Manual
4-3-10 UPnP
This page is used to configure UPnP. The system acts as a daemon when you enable
UPnP.
Choose menu “Advanced→UPnP”, below given screen will be displayed.
Here is the description of every setup item:
Parameter
Description
UPnP
Select Enable or Disable to enable or disable UPnP function.
71
DG-HR3400 User Manual
4-3-11 Routing
This page is used to configure the routing information. Here you can add/delete IP
routes.
Choose menu “Advanced→Routing”, below given screen will be displayed.
Here is the description of every setup item:
Parameter
Enable
Description
Destination
Subnet Mask
Next Hop
Metric
Enter the remote destination LAN IP.
Enter the remote LAN subnet mask.
Enter the next hop IP.
Determines the priority of the route. If multiple routes to the
same destination exist, the route with the lowest metric is
chosen.
Check this box to enable the Routing features; uncheck to
disable it.
72
DG-HR3400 User Manual
Static route table
Parameter
State
Description
Destination
Subnet Mask
Next Hop
Metric
Shows the remote destination LAN IP.
Shows the remote LAN subnet mask.
Shows the next hop IP.
Shows metric in numeric form.
Shows if Routing rule is Disabled or Enabled.
73
DG-HR3400 User Manual
4-3-12 Virtual Server
The page allows you to configure virtual server, so others can access the server
through the Gateway.
Choose menu “Advanced→Virtual Server”, below given screen will be displayed.
Here is the description of every setup item:
Parameter
Usual Service Name
Description
User-defined Service
Name
Protocol
WAN Port
LAN Open Port
LAN IP Address
Enter a name for the rule.
You can choose the type for the Usual Application Name on
the pull-down list.
The protocol used for this application, either TCP, UDP.
Enter the port that you want to open next to WAN port.
Enter the port that you want to open next to LAN port.
Enter the IP address of the computer on your local network
that you want to allow the incoming service to.
74
DG-HR3400 User Manual
4-4 Maintenance
Click ‘Maintenance’ menu on the top of web management interface, and the
following message will be displayed on your web browser:
There are eight submenus under the Maintenance menu: Reboot, Firmware
Upgrade, Backup/Restore, Password, Time and Date, System Log,
Diagnostics-Ping, Diagnostics-Traceroute. Click any of them, and you will be able
to configure the corresponding function.
4-4-1 Reboot
This page is used to reboot your system with current setting or reset configuration to
default setting.
Choose menu “Maintenance→Reboot”, below given screen will be displayed.
Here is the description of every setup item:
Parameter
Reboot
Description
Reset
Restarts the router with factory default setting.
Restarts the router for the settings to take effect.
75
DG-HR3400 User Manual
4-4-2 Firmware Upgrade
The Firmware Upgrade section can be used to upgrade to the latest firmware code to
improve functionality and performance.
Choose menu “Maintenance→Firmware Upgrade”, below given screen will be
displayed.
The Firmware Upgrade section can be used to upgrade to the latest firmware code to
improve functionality and performance.
To update the firmware, follow these steps:
 Click the Browse button to locate the upgrade file on your computer.
 Once you have found the file to be used, click the Upload button below to start
the firmware update process. This can take a minute or more.
 Wait for the router to reboot. This can take another minute or more.
NOTE: Some firmware updates reset the configuration options to the
factory defaults. Before performing any update, be sure to
save the current configuration.
76
DG-HR3400 User Manual
4-4-3 Backup/Restore
Save your configurations in a file on your computer so that it may be accessed again
later if your current settings are changed. Be sure to save the configuration before
performing a firmware update.
Choose menu “Maintenance→Backup/Restore”, below given screen will be
displayed.
Here is the description of every setup item:
Parameter
Description
Save Settings to
File
Press ‘Save’ button, and you’ll be prompted to download the
configuration as a file, default filename is ‘config.img’, you can
save it as another filename for different versions, and keep it in a
safe place.
Load Settings
From
Press ‘Browse…’ to pick a previously-saved configuration file
from your computer, and then click ‘Upload’ to transfer the
configuration file to the router. After the configuration is
uploaded, the router’s configuration will be replaced by the file
you just uploaded.
77
DG-HR3400 User Manual
4-4-4 Password
This page is used to add user account to access the web server of Wireless Router.
Empty user name or password is not allowed.
Choose menu “Maintenance→Password”, below given screen will be displayed.
Here is the description of every setup item:
Parameter
Description
User Name
Please input new User Name here.
Privilege
Please select the privilege of account you wish to use.
Old Password
Please input current password here.
New Password
Please input new password here.
Confirm
Password
Please input new password here again.
78
DG-HR3400 User Manual
4-4-5 Time and Date
This page is used to configure the system time and Network Time Protocol (NTP)
server.
Choose menu “Maintenance→Time and Date”, below given screen will be
displayed.
Here is the description of every setup item:
Parameter
Description
System Time
Displays the current time of the router. If the time is incorrect,
please fill in the correct time.
Daylight Saving
Offset
Check this option if your location observes daylight saving time.
Daylight saving time begins in the southern hemisphere between
September–November and ends between March–April. Standard
time begins in the southern hemisphere between March–April
and ends between September–November. Many countries in the
southern hemisphere may observe DST.
79
DG-HR3400 User Manual
State
There are two options here: Enable or Disable. The default value
is disable.
Server
You can fill the address used for clock synchronization of
network time server.
Time Zone
You can select your time zone drop-down box.
Start NTP
You can click Get GMT Time from network time server.
4-4-6 System Log
This page is used to display the system event log table. By checking Error or Notice
(or both) will set the log flag.
Choose menu “Maintenance→System Log”, below given screen will be displayed.
80
DG-HR3400 User Manual
Here is the description of every setup item:
Parameter
Description
Setting
By selecting the log type, only logs of this type will be shown.
Save Log to
File
Save current event log to a text file.
Clean Log Table Delete all event logs displayed here.
4-4-7 Diagnostics-Ping
This page is used to ping. Diagnostic Ping can check network reachable or not.
Choose menu “Maintenance→Diagnostics Ping”, below given screen will be
displayed.
Here is the description of every setup item:
Parameter
Description
Host
Type the destination IP address.
81
DG-HR3400 User Manual
4-4-8 Diagnostics-Traceroute
This page is used to traceroute diagnostic. Diagnostic traceroute can check network
reachable or not, and find the route path between user and the host under check.
Choose menu “Maintenance→Diagnostics Traceroute”, below given screen will be
displayed.
Here is the description of every setup item:
Parameter
Description
Host
Type the destination IP address.
Numberoftries
Type the number of tries.
Timeout
Set the waiting time for the reply of each packet. If there is no
reply in the specified time, the connection is overtime.
Datasize
The size of packet.
DSCP
Configure the DSCP parameters.
MaxHopCount The max number of hops for a traceroute connection.
Interface
By selecting the Interface type.
82
DG-HR3400 User Manual
4-5 Status
Click ‘Status’ menu on the top of web management interface and the following
message will be displayed on your web browser:
There are four submenus under the Status menu: Device Info, Active Client Table,
Statistics and IPv6. Click any of them, and you will be able to view the
corresponding status.
4-5-1 Device Info
This page shows the current status and some basic settings of the device.
Choose menu “Status→Device Info”, below given screen will be displayed.
83
DG-HR3400 User Manual
4-5-2 Active Client Table
This table shows IP address, MAC address for each client.
Choose menu “Status→Active Client Table”, below given screen will be displayed.
4-5-3 Statistics
This page shows the packet statistics for transmission and reception regarding to
network interface.
Choose menu “Status→Statistics”, below given screen will be displayed.
84
DG-HR3400 User Manual
4-5-4 IPv6
This page shows the IPv6 internet and network connection details.
Choose menu “Status→IPv6”, below given screen will be displayed.
85
DG-HR3400 User Manual
5. Appendix

Hardware Specifications
-

Network Ports
-

2.4000 ~ 2.4835 GHz
WLAN Data Transfer Rates
-

IEEE802.3 10 Base-T Ethernet
IEEE802.3u 100 Base-TX Ethernet
IEEE802.11b, IEEE802.11g, IEEE802.11n
Frequency Band
-

Power, WAN, LAN (1-4), WLAN, WPS
Standards Compliance
-

1 * 10/100Mbps UTP WAN Port
4 * 10/100Mbps UTP LAN Ports
Status LED
-

Antenna: Two fixed 5 dBi antenna
WPS Push Button
Factory reset button
IEEE802.11b up to 11Mbps
IEEE802.11g up to 54Mbps
IEEE802.11n up to 300Mbps
Wireless Output Power
-
IEEE802.11b: 23 +/- 1 dBm
IEEE802.11g: 19 +/- 1 dBm
IEEE802.11n: 18 +/- 1 dBm
86
DG-HR3400 User Manual

Environmental Specifications
-

Operating temperature: 0 to 40°C
Storage Temperature: -40 to 70°C
Operating Humidity: 10 % to 90 %
Storage Humidity: 5% to 95%
Power Supply
-
5V DC, 1A Switching Power Adapter
87
DG-HR3400 User Manual
6. Glossary
Default Gateway (Router): Every non-router IP device needs to configure a default
gateway IP address. When the device sends out an IP packet, if the destination is not
on the same network, the device has to send the packet to its default gateway, which
will then send it to the destination.
DHCP: Dynamic Host Configuration Protocol. This protocol automatically gives
every computer on your home network an IP address.
DNS Server IP Address: DNS stands for Domain Name System, which allows
Internet servers to have a domain name (such as www.Broadbandrouter.com) and one
or more IP addresses (such as 192.34.45.8). A DNS server keeps a database of
Internet servers and their respective domain names and IP addresses, so that when a
domain name is requested (as in typing "Broadbandrouter.com" into your Internet
browser), the user is sent to the proper IP address. The DNS server IP address used by
the computers on your home network is the location of the DNS server your ISP has
assigned to you.
DSL Modem: DSL stands for Digital Subscriber Line. A DSL modem uses your
existing phone lines to transmit data at high speeds.
Ethernet: A standard for computer networks. Ethernet networks are connected by
special cables and hubs, and move data around at up to 10/100 million bits per
second (Mbps).
Idle Timeout: Idle Timeout is designed so that after there is no traffic on the Internet
for a pre-configured amount of time, the connection will automatically get
disconnected.
IP Address and Network (Subnet) Mask: IP stands for Internet Protocol. An IP address
consists of a series of four numbers separated by periods, which identifies a single,
unique Internet computer host in an IP network. Example: 192.168.2.1. It consists of
2 portions: the IP network address, and the host identifier.
The IP address is a 32-bit binary pattern, which can be represented as four cascaded
decimal numbers separated by “.”: aaa.aaa.aaa.aaa, where each “aaa” can be anything
from 000 to 255, or as four cascaded binary numbers separated by “.”:
bbbbbbbb.bbbbbbbb.bbbbbbbb.bbbbbbbb, where each “b” can be either 0 or 1.
88
DG-HR3400 User Manual
A network mask is also a 32-bit binary pattern, and consists of consecutive leading
1’s followed by consecutive trailing 0’s, such as
11111111.11111111.11111111.00000000. Therefore sometimes a network mask can
also be described simply as “x” number of leading 1’s.
When both are represented side by side in their binary forms, all bits in the IP address
that correspond to 1’s in the network mask become part of the IP network address,
and the remaining bits correspond to the host ID.
For example, if the IP address for a device is, in its binary form,
11011001.10110000.10010000.00000111, and if its network mask is,
11111111.11111111.11110000.00000000
It means the device’s network address is
11011001.10110000.10010000.00000000, and its host ID is,
00000000.00000000.00000000.00000111. This is a convenient and efficient method
for routers to route IP packets to their destination.
ISP Gateway Address: (see ISP for definition). The ISP Gateway Address is an IP
address for the Internet router located at the ISP's office.
ISP: Internet Service Provider. An ISP is a business that provides connectivity to the
Internet for individuals and other businesses or organizations.
LAN: Local Area Network. A LAN is a group of computers and devices connected
together in a relatively small area (such as home or office). Your home network is
considered a LAN.
MAC Address: MAC stands for Media Access Control. A MAC address is the
hardware address of a device connected to a network. MAC address is a unique
identifier for a device with an Ethernet interface. It is comprised of two parts: 3 bytes
of data that correspond to the Manufacturer ID (unique for each manufacturer), plus 3
bytes that are often used as the product’s serial number.
NAT: Network Address Translation. This process allows all the computers on your
home network to use one IP address. Using the broadband router’s NAT capability,
you can access Internet from any computer on your home network without having to
purchase more IP addresses from your ISP.
Port: Network Clients (LAN PC) uses port numbers to distinguish one network
application/protocol over another. Below is a list of common applications and
protocol/port numbers:
89
DG-HR3400 User Manual
Application
Protocol
Port
Number
Telnet
TCP
23
FTP
TCP
21
SMTP
TCP
25
POP3
TCP
110
H.323
TCP
1720
SNMP
UDP
161
SNMP Trap
UDP
162
HTTP
TCP
80
PPTP
TCP
1723
PC Anywhere
TCP
5631
PC Anywhere
UDP
5632
PPPoE: (Point-to-Point Protocol over Ethernet.) Point-to-Point Protocol is a secure
data transmission method originally created for dial-up connections; PPPoE is for
Ethernet connections. PPPoE relies on two widely accepted standards, Ethernet and
the Point-to-Point Protocol. It is a communications protocol for transmitting
information over Ethernet between different manufacturers.
Protocol: A protocol is a set of rules for interaction agreed upon between multiple
parties so that when they interface with each other based on such a protocol, the
interpretation of their behavior is well defined and can be made objectively, without
confusion or misunderstanding.
Router: A router is an intelligent network device that forwards packets between
different networks based on network layer address information such as IP addresses.
Subnet Mask: A subnet mask, which may be a part of the TCP/IP information
provided by your ISP, is a set of four numbers (e.g. 255.255.255.0) configured like an
IP address. It is used to create IP address numbers used only within a particular
network (as opposed to valid IP address numbers recognized by the Internet, which
must be assigned by InterNIC).
90
DG-HR3400 User Manual
TCP/IP, UDP: Transmission Control Protocol/Internet Protocol (TCP/IP) and
Unreliable Datagram Protocol (UDP). TCP/IP is the standard protocol for data
transmission over the Internet. Both TCP and UDP are transport layer protocols. TCP
performs proper error detection and error recovery, and thus is reliable. UDP on the
other hand is not reliable. They both run on top of the IP (Internet Protocol), a
network layer protocol.
WAN: Wide Area Network. A network that connects computers located in
geographically separate areas (e.g. different buildings, cities, countries). The Internet
is a wide area network.
Web-based management Graphical User Interface (GUI): Many devices support a
graphical user interface that is based on the web browser. This means the user can use
the familiar Netscape or Microsoft Internet Explorer to Control/configure or monitor
the device being managed.
91