A(BCD-5500UB PY-6868U)说明书

BCD-5500UB
CAR CD / MP3 PLAYER
/ RECEIVER
USB / SD / MMC / SLOT
CD/DVD New feat ure and ope ration notice
4. AEM ( Aux Extend voice control Mode )
GPS traffic broadcasting:
Under any mode, connect iPhone to AUX in, activate GPS Navigation function on the
phone(The phone must have this Apps).
Set AEM ON, while GPS Navigation traffic broadcasting, the radio sound of current mode
will be decreased,If the Navigation stop broadcasting over 5 sec, the radio sound will be
back to play.
AEM ON:
Long press SEL key, then short press SEL to select AEM ON/OFF, rotate Volume knob to
set ON, AEM function activated.
AEM OFF:
Repeat above steps, just in the last step, set OFF to deactivate AEM function.
* Connect iPhone to Aux in with provided cable (option to be sold separately).
** When AEM ON, any audio source from iPhone can be broadcasted to Headunit.
Below two brackets are provided for your choice:
Installation . . . . ...... . . . . ....... . . . . ...... . . . . . ...... . . . . ... . 02
Additional information ................................. 04
General operations ...................................... 05
Radio operations ......................................... 08
CD/SD/MMC/USB Operations ................... .. 10
MP3 WMA overview .............................. . . . . . .. 13
Remote control layout ............................. ..... 14
Specification ................................................. 16
Before playing discs ................................. . ... 17
Trouble shooting ............................................ 18
4301SPR
4303SPR
CD/DVD New feature and operation notice .... 19
5. IPH ( iPhone Handfree)
Answering Phone Calls:
Under any mode, connect iPhone to AUX in, when call's coming , press PLAY key or Mobile
Phone's answer key to answer it.
Press again to hang up. During answer call,The sound of current mode will be decreased
If the Call finish over 5 sec, the sound will be back to play.
**To have a better phone call experience, long press "MU" to enter "PHONE" mode when
you answer the phone. Then long press “MU” again to go back to previous mode when
phone call finishes.
AEM default setting is AEM ON.
●IPC, AEM, IPH functions support iPhone, some smartphone models of Motorola, HTC,
T-Mobile, BlackBerry, LG and Sumsung(which comply with iPhone's socket 4H / 3.5mm).
e.g. Motorola XT615, LG920, Sumsung Galaxy Note….etc.
** Support compatibility subject to change without further notice & not guarantee.
Below two brackets are provided for your choice:
4301SPR
20
4303SPR
01
CD/DVD New feat ure and ope ration notice
INSTALLATION
1. DOS ( Dynamic Open Screen )
PRECAUTION S
The Dynamic Open Screen (Motion effect) when unit power on. Press any key to stop and
Cho os e the moun ting loc at ion whe re the un it wi ll no t int er fer e wi th the no rmal
driving function of the driver.
Bef or e final ly ins tal ling the uni t, co nne ct the wi ring tem por ar ily and mak e su re
it is all connected up properly and the unit and the system work properly.
Use onl y the par ts incl uded wi th the uni t to ens ur e pr oper inst al lat ion. The use
of unauthorized parts can cause ma lfunctions.
return to the current mode.
DEMO ON:
L ong press SEL key (chang to SEL mode), then short press SEL to select Demo ON/OFF,
rotate Volume knob to set Demo ON, Then press SEL to confirm. The Dynamic OpenScreen
display will repeatedly.DEMO ON mode used to demonstration. All buttons are not workable
except "SEL" button.
Con sul t wi th you r ne ar es t de al er if ins tal lat ion req ui res the dr illing of ho les or
other mo difications of the vehicle.
DEMO OFF:
Install the unit where it does not get in the driver's way and cannot injure the
passenger if there is a sudden stop. Like an eme rgency stop.
default status.
Press SEL key, rotate Volume knob to set Demo OFF , press SEL to confirm, then back to
2. RGB (Customize RGB Color illumination)
If installation angle exceeds 30 from horizontal, the unit mi ght not give its
optimu m performa nce.
The illumination color keep changing when unit Power on.
Fixed Color Setting:
0
30
Long press DISP key , rotate Volume to select Auto OFF, short press DISP to select fixed
color from blue, green, red, orange, purple and white.
Avoid installing the unit where it would be subject to high temp erature, such
as from direct sunlight, or from hot air, form the heater, or where it would be
subject to dust, dirt or excessive vibration. Do not expose this equipment
to rain or moisture.
Customize Color Setting:
Long press DISP key, rotate Volume to select Auto OFF, press DISP to enter customize
color setting:
e.g.
RED - rotate Volume to select 00~32, press DISP to confirm the setting.
GREEN - rotate Volume to select 00~32, press DISP to confirm the setting.
BLUE - rotate Volume to select 00~32, press DISP to confirm the setting.
DIN FRON T-MOU NT (Me thod A)
3. IPC (iPhone Control Music)
Installing the unit
With this function, the music in iPhone can be played on headunit, and can be controlled
1. Dashboard
2. Holder
After inserting the holder into
the dashboard, select the
appropriate tab according to
the thickness of the dashboard
ma terial and bend them
inwards to secure the holder in
(Fig. 1)
place.
2
1
by headunit to operate PLAY/PAUSE, PREV, NEXT.
Press Mode button to select Aux model. Connect iPhone to Aux in with provided cable
(option to be sold separately).
3
Below two brackets are provided for your choice:
(Fig. 1)
3. Screw
4301SPR
02
4303SPR
19
TROUBLE SHOOTING
INSTALLATION
1
Before going through the check list, check wiring connection. If any of the
problems persist after checklist has been made, consult your nearest service
dealer
Removing the unit
6
1
7
4
2
5
2
3
3
Symptom
No Power
CD Cannot Be
Loaded or Ejected
No Sound
Causes
Solution
The car ignition key not
been switched on
If the power supply is properly
connected to the car accessory
terminal, switch the ignition
key to ACC
The fuse is blown
Replace a new fuse
A CD is already inside the
player slot
Remove the CD from the player
and insert the new one
Inserting the CD in reverse
direction
Insert the CD with the label
facing up
The CD is extremely dirty or
defected
Clean the CD or try to play
a new one
Temperature inside the car is
too high
Cool off until the ambient
temperature return to normal
Condensation
Leave the player off for an
hour or so and try again
Volume is at minimum
Adjust volume to desired level
( Fig . 2 )
( Fig . 3 )
1. Dashboard
2. Nut (5mm)
3. Spring Washer
4. Screw (5 x 25mm)
5. Screw
6. Strap
Be sure to use the strap to
secure the back of the unit in
place. The strap can be bent by
hand to the desired angle.
7. Plain Washer
Fastening the unit to the factory
radio mounting bracket:
2
Wiring is not properly
connected
Check wiring connection
The installation angle is more
o
than 30
Adjust the installation angle to
o
less than 30
CD is extremely dirty or
Defected
Clean the CD or try to play
a new one
Do Not Work
The built-in microcomputer is
not operating properly due to
Interference
Press the RESET button or
reinstall the front panel
properly
The Radio or
The antenna cable is not
connected correctly
Connect the antenna cable
correctly
The signals are too weak
Select the station manually
3
Sound Skipping
The Operation Keys
Automatic Selection
Does Not Work
2.Insert fingers into the groove in the
front of fram e and pul l out to remove
the fram e. (When reatt achi ng the
frame , point the side wi th a groove
dow nw ards and attach it.)
3.Leve r
Insert the levers supp lied with the
uni t into the grooves at both si des of
the uni t and sho wn in figure unti l they
click. Pulling the levers makes possible
to remove the unit fro m the dashboard.
2
1. Select a position where the screw
holes of the bracket and the
screw holes of the main unit
become aligned (are fitted), and
tighten the screws at 2 places on
each side. Use either truss screws
(5 x 5mm) or flush surface screws
(4 x 5mm)
2. Screw
3. Dashboard or Console
DIN REAR-MOUNT (Method B)
Installation using the screw holes on
the sides of the unit
INPUT THE SD CARD
The SD oblique angle keeps
rightward exposure , put into
the SD slot and press it again
to eject .
18
03
ADDITIONAL INFORMATION
BEFORE PLAYING DISCS
Cleaning the CD
Before playing a CD, wipe it off with a clean, dust-free cleaning cloth.
Wipe the disc in the direction of the arrow.
RE AR Rc h LINE OU T
RE AR Lch LINE OU T
RED
YELLOW
Always insert the CD with the label side facing upwards.
If the CD is inserted with the printed side facing downwards, the device
may be damaged.
BLACK
BLUE
WHITE
WHITE/BLACK
GREEN
GREEN/BLACK
GREY
GREY/BLACK
VIOLET
VIOLET/BLACK
HOW TO INSTALL AND REMOVE THE FRONT PANEL
INSTALLING THE FRONT PANEL
To install the front panel, insert the panel into the housing and ma ke sure the panel
is properly installed, otherwise, abnormalities occurs on the display or
some keys will not function properly
1
Note: If there is already a CD in the CD slot , do not try to insert a second
CD. This may damage the device.
Always hold CDs by the edge. In order to keep the CD clean do not touch
the surface. Pull out the CD as follows.
3
2
Do not attach any sticker or adhesive tape on the CD.
Do not expose the CD to direct sunlight or sources of heating.
Do not leave CDs in a car if it parked in direct sunlight as that will lead to
a considerable rise in the temperature inside the car.
Note: Do not use any solvents such as petrol or thinning agents. Commercially
available cleaning substances of antistatic spray will damage the device.
04
17
SPECIFICATION
GENERAL OPERATIONS
FRONT PANEL LAYOUT
2
5 10
3
12
1
6
21
20
22 19
100
BCD-5500UB
11
9
4
13
14
15
16
17
18
24
23
7
8
1. Power/MOD Button
13. Play / Pause & Preset Button 1
2. Release Button
14. Intro & Preset Button 2
3.
4.
5.
6.
7.
8.
16. Random & Preset Button 4
17. Preset Button 5
18. Preset Button 6
19. Eject knob
Volume/ Sel Button
Mute Button
Disp-Color/ setting
LCD Display
Flashing LED
Reset Button
9. Band switch /ID3 select
10. Tune Seek&Track forward Button
11. Tune Seek&Track reverse Button
12. Automatically memory storing
16
15. Repeat & Preset Button 3
20. CD Slot
21. Remote Control Sensor
22. USB connecter
23. SD/MMC Slot
24. AUX IN JACK
05
GENERAL OPERATIONS
REMOTE CONTROL LAYOUT
GENERAL OPERATIONS
Replacing the Battery
POWER /MOD conversion
2.Under power off status,short press is power on,
Under power on status,short press is switching mode,long press is power off.
When the operational range of the remote control becomes short or non functions while
operating . Replace a new CR2025 battery . Make sure the battery polarity before
replacement .
FRONT PANEL RELEASE
1.Pull out Battery Holder while pressing the stopper
Press REL button (2) to detach the removable front panel
SOUND ADJUSTMENT
Turn on (3) can adjust the desired volume quality.
A).Press SEL button (3) will change in the following order.
Option:
VOL
(Volume)
BAS
TRE
(Bass)
( Treble)
BAL
(Balance)
FAD
( Fader)
2.Put the button type battery(+)mark upward into the Battery Holder.
Volume control/select
Rotating this knob, you can adjust VOL/BASS/TREB/BAL/FAD . To select the
functions, press the VOL knob shortly until the desired functions are shown on the
display.
Increase or decrease the volume by turn the VOL knob right or left. These buttons
can be used to adjust the BASS, TREBLE, BALANCE and FADER.
BASS
3.Insert the Battery Holder into the Remote control
Press VOL/SEL button(3) one time. Adjust bass level by using VOL/SEL(3)Knob.
TREBLE
Press VOL/SEL button(3) two times. Adjust treble level by using VOL/SEL(3)
Knob
BALANCE
Press VOL/SEL button(3) three times. Adjust sound balance between left and
right speakers by using VOL/SEL(3)Knob.
06
15
REMOTE CONTROL LAYOUT
GENERAL OPERATIONS
POWER
1
9
18
8
SEL
AREAEUR/USA
DISP
AMS
MODE
BAND
LOC
INT
RPT
1
2
3
4
5
6
RDM
10
10
ST
17
10
DX/LOCAL
STEREP/MONO
DEMO OFF/ON
SEEK ½
AEM OFF/ON
BEEP ON / OFF
11
LOUD
12
SCN
13
3
5
VOL LAST/ADJ
LOUD OFF / ON
16
TOP
2
DSP OFF ON
19
15
14
TIME DISPLAY
4
7
6
1
2
3
4
5
6
7
8
9
Power Button
Pause/play/ Preset B utton 1
Intro /Preset Button2
Repeat Playing/Preset Button3
Random/Preset Button4
Preset Button5
Preset Button6
Mute Button
Volume Control
10
11
12
13
14
15
16
17
18
19
Mode Switch
ST/MO Button
Loudness Button
Scan Button
Disp-Color/ setting
APS / AMS Button
LOC/DX Button
Band Switch
Tuning / Selecting Tracks / F . F / F . R
Select Button
Time Adjusting
Press and hold the SEL button until the current time is displayed. Then Press the vol"+"
to adjust hours, and press the vol"-" to adjust minutes. After you finish the time
adjustment , press SEL button to confirm the time setting.
LIQUID CRYSTAL DISPLAY
Exhibit current frequency and activated functions on the display (6).
FLASHING LED
Remote Control Optional
14
When ACC off ,take out the front panel from main unit that the LED (7) will be flashing.
07
RADIO OPERATIONS
BAND SELECTION
FM1
FM2
FM3
AM1 ( MW 1)
AM2 ( MW 2)
STATION SELECTION
Press TUNE/SEEK/TRACK FORWARD button (10) or TUNE/SEEK/TRACK
REVERSE button (11) shortly for manual tuning function.
Press for several seconds the automatic tuning mode (SEEK
mode) is selected.
AUTOMATICALLY MEMORY STORING & PROGRAM SCANNING
- Automatically Memory Storing
Press AMS(MP3) button (12) for several seconds, the radio searches from the
current frequency and checks the signal strength until one cycle search is finished.
And then 6 strongest stations are stored into the corresponding preset number
button.
- Program Scanning
Press AMS(MP3) button (12) shortly to scan preset station. When the field strength
level is mo re than the threshold level of stop level, the radio is holding at that preset
number for several seconds with releasing mute, then searches again.
STATION STORING
Pr ess preset button (13~18)
1) RADIO MODE.
M1 ~ M6
- PRESET MEMORY is loaded when key is pressed for less than 1 second.
- PRESET MEMORY is saved when key is pressed for longer than 1 sec.
2) CD / MP3 / FLASH MP3
PLAY / PAUSE
Press preset button (13) is activated. During a PAUSE, DISC INDICATOR flashes.
TOP - Fi rst son g wi ll pl ay whe n Top key is pr es sed for lon ge r tha n 0. 5s ec du ring pl ay.
INT
Press preset button (14) : During INTRO ON, INT indicator comes on and
begins playing the first 10sec of each song, until the last song is played. It begins
playing the entire track from where INT started
08
MP3 is short for MPEG Audio Layer 3 and refers to an audio compression
technology standard.
· This product allows playback of MP3 files on CD-ROM, CD-R or CD-RW discs.
· The unit can read MP3 files written in the format compliant with ISO 9660.
However it does not support the MP3 data written by the method of packet write.
· The unit can not read an MP3 file that has a file extension other than “.mp3”
· If you play a non- MP3 file that has the “.mp3” extension, you may hear some
noise.
· In this manual, we refer to what are called “MP3 file” and “ folder” in PC
terminology as “ track ” and “ album ”, respectively.
· Maximum number of directory level is 8, including the root directory. Maximum
number of files and folders per disc is 256.
· The unit may not play tracks in the order of Track numbers.
· The unit plays only the audio tracks if a disc contains both audio tracks and
MP3 files.
· When playing a disc of 8 kbps or “VBR”, the elapsed playing time in the display
window will not be correct and also the intro play may not function properly.
“ VBR ”:Variable Bit Rate.
· The unit supports the playback of WMA files. The playback of ID3 tags for WMA
format is not guaranteed, it depends on versions and availability of Cyrillic
alphabet.
· WMA (Windows Media Audio) -music data compression format, created by
Microsoft Corporation. This format uses coding algorithm for compression of
initial audio-record, greatly decreasing the file size, but, saving the good sound
quality even when the bit rate is low (for example, 64 Kbit/s).
· Remember that the unit may not play the tracks in order they are written on disc.
·
At tuner mode, press BAND button (9) to select the desired band. The
reception band will change in the following order:
Notes on creating your own CD-R or CD-RW containing MP3 files:
To enjoy high quality sound, we recommend converting to MP3 files with a
sampling frequency of 44.1 kHz and a fixed bit rate o f 128 kbps.
· DO NOT store more than 256 MP3 files per disc.
· For ISO 9660 - compliant format, the maximum allowable depth of nested
folders is 8, including the root directory (folder).
· When CD-R disc is used, playback is possible only for discs, which have been
finalized.
· Make sure that when MP3 CD-R or CD-RW is burned that it is formatted as a
data disc and NOT as an audio disc.
· You should not write non-MP3 files or unneeded folders along with MP3 files
on the disc otherwise it takes a long time until the unit starts to play MP3 files.
· With some CD-R or CD-RW media, data may not be properly written depending
on its manufacturing quality. In this case, data may not be reproduced correctly.
High quality CD-R or CD-RW disc is recommended.
· Up to 16 characters are displayed for the name of an Album or a Track. ID3TAG
version 1.x is required.
· Note that the unit may not play Tracks in the order that you wrote them to the
disc.
·
13
CD/SD/MMC/USB OPERATIONS
RADIO OPERATIONS
LOCAL RADIO STATION SEARCH
2. Searching Track
•Press AMS twice, then searching track is activated.
•Turn VOL knob to right or left, select the track you want.
•Press VOL knob, the song you selected will start.
3. Searching File Name:
•Press AMS 3 times, then file search is activated.
•Press VOL knob, then the first directory is displayed.
•Turn VOL knob to right or left, you can select the directory you want.
•Press VOL knob again, then the directory is fixed and the first file name is
displayed.
•Turn VOL knob to right or left, you can select the file you want.
•Press VOL knob, then the song you selected will start.
4. Searching Character:
•Press AMS 4 times, then character search mode is activated.
•Press VOL knob, then * character is displayed.
•Turn VOL knob to right or left, you can select the letter you want.
•Press VOL knob longer than 2 sec.
•The song which has same character you selected is displayed.
•Turn VOL knob to right or left, you can select the song you want.
•Press VOL knob, then the song you selected will start.
12
Press SEL button repeatedly to choose LOCAL(DX).Rotate VOL regulator or
press VOL+/- buttons on the RCto switch between LOCAL and DX.When the
LOCAL function is on the local stations(stations with weak radio)
Press SEL button repeatedly until LOUD ON is displayed.Rotate VOL regulator
on the front panel or press VOL+/VOL- buttons on the RC to select loudness
ON or OFF.
MOno/Stereo control (in FM radio mode)
Press SEL button repeatedly until the display shows STEREO (MONO).Rotate
VOL regulator or press VOL+/- buttons on the RC to switch between STEREO
reception and MONO reception.Improvement of reception of distant stations
can be done by selecting mono mode,which may cut down some reception noise.
AREA USA/EUR SETUP
In Radio mode. Press SEL button for several seconds. LCD will be show from
DSP OFF/ON AREA USA/EUR. At AREA USA/EUR. You can use VOL +/to select the AREA frequency.
09
CD/SD/MMC/USB OPERATIONS
CD/SD/MMC/USB OPERATIONS
Discs for playback:
Id3 Tag information
This unit can play disc types: CD/CD -R/-RW.
Compatible with formats: CDDA/MP3/WMA.
This unit supports ID3 tag ver2.0. If an MP3/WMA file has ID3 Tag information,
it will be displayed on the LCD. If there is no ID3 Tag information, nothing will be
shown on LCD. The ID3 Tag information may include File, Folder, Music,Album
or Artist data.
Loading and ejecting a disc
1. Turn the power on.
2. Insert the disc with the printed side facing upward into the slot.
3. Press EJECT button to eject the disc.
NEXT/PREVIOUS
Press NEXT/PREVIOUS buttons to choose next or previous track. Press longer
than 1 sec., to choose forward playback or backward playback.
Multi-media card MMC/SD card slot
PLAY/PAUSE
Support MP3/WMA ID3 format music only. Detach the front panel. Carefully
insert the SD/MMC card into the card slot on the inner panel. Attach the panel.
Unit starts playback automatically.
Press PAUSE button to pause the playback, press one more time to resume the
normal playback.
USB jack
INTRO (Preview all Tracks)
Carefully connect the USB driver to the USB adapter cable and then insert it into
the USB jack on the front panel. Unit starts playback automatically.
When this button is pressed, "INT ON" indication is displayed and the first
several seconds of each track of the disc is played. Press again to stop intro and
listen to track.
USB/SD/MMC notes:
USB functions (flash memory type) MP3 music play.
1. SD/ MMC card support.
2. FAT 12/ FAT 16/ FAT 32 is possible
- FAT 12/16 (dir: 200 support, file:500 support),
- FAT 32 (dir: 200 support, file:500 support).
3. Filename: 32 byte/ Dir name: 32byte.
4. Tag (id3tag ver2.0)
- Title/ Artist/ Album: 32 byte support.
5. Multi card reader not support.
6. USB 2.0 support.
REPEAT
When RPT button is pressed, "PT ON" indication is displayed and playback of
the selected track will be continually repeated until the track repeat mode is
cancelled by pressing RPT button again.
RANDOM
When RDM button is pressed,"RDM ON" indication is displayed and each track
of the disc is played in random instead of normal order. To cancel RANDOM
mode, press RDM button again.
Note:
TRACK DOWN/UP SELECT (In case of MP3/WMA files)
USB format supports 2.0.
Capacity: up to 4 GB.
SD cards brands: Cannon, Fuji film, Palm, Motorola, Microsoft, IBM, HP,
Compaq, Sharp, Samsung, etc.
Capacity: up to 4 GB.
MMC cards brands: Ericsson, Nokia, Motorola, HP, Palm, Sanyo, Microsystems,
etc.
Capacity: up to 4 GB.
Note: Because of the great variety of products with SD and MMC card slots and
their sometimes quite manufacturer-specific functions the producer can neither
guarantee that all devices will be recognized nor that all operating options that
are possible in theory will actually work.
-10/5 button: 10 Track down
+10/6 button: 10 Track up
10
Selection of MP3/WMA files
1.Searching Time
•Press AMS one time, then searching time is activated.
•Turn VOL knob to right or left, select the time you want.
•Press VOL knob, then the select time of the song will play
11