2-Port Serial-Ethernet Server STE-502C Quick Start Guide

2-Port Serial-Ethernet Server
STE-502C
Quick Start Guide
Version 1.3
Quick Start Guide Version 1.3
Serial to Ethernet Device Server
STE-502C
This document intends to provide customers with brief descriptions about the product and to assist
customers to get started. For detail information and operations of the product, refer to the product user’s
manual in the product CD.
1
Packaging
Check your package contains the following items:
STE-502C Serial to Ethernet Server

Quick Start Guide

Product CD

Wall mounting screws
2
Hardware Description
NOTE:
Press the reset button of the STE-502C to reset to the default value. 0 shows the interface
Fig. 1
STE-502C interfaces
LED Indicators:
Message
Off
Blinking with Green
Blinking with Orange
Description
Ethernet Disconnected
Data transmitting on Ethernet at 100Mbps
Data transmitting on Ethernet at 10Mbps
Table 1. LAN LED Message
Copyright © 2013 Antaira Technologies, LLC
All rights reserved.
1
Quick Start Guide Version 1.3
Serial to Ethernet Device Server
STE-502C
Message
Off
Com 1(2)TX Blinking
Com 1(2)RX Blinking
Description
No data transmitting on COM port
Data transmitting on COM port
Data Receiving on COM port
Table 2. COM Port LED Message
Description
Message
On
Jumper JP1 Pin1 and Pin2 are shorted to disable AP firmware
AP firmware running normally
Table 3. RUN LED Message
Blinking (rate: 0.5 Sec)
Installation Procedures:
Step 1: Connect the STE-502C to power source
Step 2: Connect the STE-502C to the Ethernet network. Use a standard straight-through Ethernet cable
when connect to a hub/switch, or connect to a PC‘s Ethernet port via a cross-over Ethernet cable.
However, Always make sure your PC is on the same network sub-net as the STE-502C.
Step 3: Connect the STE-502C’s serial port to a serial device.
Step 4: Mount the STE-502C to a wall/panel with the screws included or Din-Rail rack (Require optional
item model: Din-Rail-Kit).
3
Software Setup
Default Network Setting: Default User Name/Password:
IP: 10.0.50.100
User Name: admin
Gateway: 10.0.0.254
Password: null (leave it blank)
Subnet: 255.255.0.0
Auto IP (Dynamic IP):
A DHCP server can automatically assigns the IP address and all the network settings. The STE-502C
supports the DHCP client function. By default, the DHCP client function on the STE-502C is disabled; you
may activate the DHCP client functions by executing monitor.exe (0)
Fig. 5
monitor.exe utility Dialog Window
Copyright © 2013 Antaira Technologies, LLC
All rights reserved.
2
Quick Start Guide Version 1.3
Serial to Ethernet Device Server
STE-502C
Assign a Static IP address by:
A
Configuration by Telnet
1.
Telnet to the STE-502C using DOS command “Telnet IP_address”. Example: telnet
10.0.50.100
2.
B
Network, Link Mode, and COM Ports settings can be configured in the telnet window
Configuration by Monitor.exe Utility
Use Monitor.exe on Product CD to configure the STE-502C.First click” Config” then assign a static
IP.
C.
Configuration by Web Browser
1.
Make sure the PC is on the same network as the STE-502C
2.
Open a web browser, then Enter in the IP address as the STE-502C. The default user name is
admin and default password is null (leave it blank).
3.
The STE-502C’s network, link mode and COM ports settings can be configured on different
web pages.
4
4.
Click “Save Configuration” to save settings.
5.
Click ”Restart” button to initiate the change.
Pin Assignments
The pin assignments of DB9 connector on the STE-502C is shown in the following table:
RS-232
RS-485
RS-485/RS-422
Pin#
Full Duplex
2 wire, Half Duplex
4 wire, Full Duplex
5
1
2
3
4
5
6
7
8
DCD
RXD
TXD
DTR
SG (Signal Ground)
DSR
RTS
CTS
N/A
N/A (reserved)
DATA+
N/A
SG (Signal Ground)
N/A
DATAN/A(reserved)
N/A
TXD+
RXD+
N/A
SG (Signal Ground)
N/A
RXDTXD-
9
N/A
N/A
N/A
Customer Services and Supports
1) Contact your local dealers or Antaira Technical Support Center at the following numbers.
 1-877-229-3665
 1-714-671-9000
2) Report the errors via website or e-mail
www.antaira.com / support@antaira.com
Copyright © 2013 Antaira Technologies, LLC
All rights reserved.
3