K3SC Interface Converter

K3SC
Interface Converter
A compact converter that allows
communications between RS-232C/USB
and RS-422/485 devices. Ideal for
industrial applications.
■ Allows communications between RS-232C/USB
(Universal Serial Bus) and RS-422/485 devices.
■ All signal lines have 1,500-VAC insulation at the
RS-232C/USB and RS-422/485 sides using optocouples, and power supply lines have 1,500-VAC
insulation using a transformer.
4
■ Compact 30-mm-wide body supports both screw-
mounting and DIN track mounting.
C
■ LED indicator for RD, SD, and power.
■ Operation either with or without echoback avail-
US
able.
■ Conforms
to
(IEC61010-1).
EMC
standards,
EN61010-1
■ UL/CSA approved.
Ordering Information
Appearance
Size (mm)
Power supply voltage
30 × 80 × 78 (W × H × D)
■
Model
100 to 240 VAC
K3SC-10 100 to 240 VAC
24 VAC/VDC
K3SC-10 24 VAC/VDC
Accessories (Order Separately)
Name
Model
Adapter for RS232C Serial Cable and K3SC K32-23209
Specifications
■
Ratings
Item
K3SC-10 100 to 240 VAC
K3SC-10 24 VAC/VDC
Power supply voltage
100 to 240 VAC 50/60 Hz
Allowable power supply fluctuation range
85% to 110% of power supply voltage
Power consumption
5 VA max.
Communications format of master device (e.g.,
computer)
RS-232C, USB (selectable)
Communications format of slave device (e.g.,
component)
RS-422: 4-wire full-duplex mode, RS-485: 2-wire half-duplex mode (selectable)
Communications method
Start-stop synchronization
Ambient operating
temperature
RS-232C
−10 to 55°C (with no icing)
USB
0 to 55°C (with no icing)
Ambient operating humidity
25% to 85% (with no condensation)
Ambient storage temperature
−20 to 65°C
24 VAC 50/60 Hz, 24 VDC
3 VA max./3 W max.
1
K3SC
■
K3SC
Characteristics
Item
RS-232C
interface
Specification
Maximum
transmission
distance
15 m
Master
device
Maximum number of 1 Unit
connectable Units
USB interface Maximum
(See note 1.) transmission
distance
5 m; hub delay time + cable delay time ≤ 70 ns
Maximum number of 1 Unit
connectable Units
Slave
device
RS-422/485
interface
USB standard
V1.1
Maximum
transmission
distance
500 m
Maximum number of 31 Units (for multi-drop connection)
connectable Units
Baud rate
1,200/2,400/4,800/9,600/19,200/38,400 (bps)
Default setting: 9,600
Data length
7/8 bits
Default setting: 7
Stop bit length
1/2 bits
Default setting: 2
Communications parity
None/even/odd
Default setting: Even
Echoback selection
Echoback: With/without
Default setting: Without
Selection switch response delay
Approx. 30 ms
Insulation resistance
20 M Ω min. measured at 500 VDC between the following:
External terminals ↔ casing
RS-232C terminals and USB port ↔ RS-422/485 terminals ↔ power supply terminals
Isolation Commumethod nications
Power
supply
Phototransistor coupler
Isolating transformer
Dielectric strength
1,500 VAC for 1 minute measured between the following:
External terminals ↔ casing
RS-232C terminals and USB port ↔ RS-422/485 terminals ↔ power supply terminals
Noise immunity
AC power supply terminals, normal/common mode: ±1,500 V
AC/DC power supply terminals, normal mode: ±480 V; common mode: ±1,500 V
Square wave with 1-ns rising edge ±1 µs, ±100 ns
Vibration resistance Malfunction
Shock resistance
10 to 55 Hz, 0.5-mm single amplitude for 10 minutes each in X, Y, and Z directions
Destruction
10 to 55 Hz, 0.5-mm single amplitude for 2 hours each in X, Y, and Z directions
Malfunction
98 m/s2 3 times each in X, Y, and Z directions
Destruction
Weight
294 m/s2 3 times each in X, Y, and Z directions
Approx. 150 g
Enclosure rating
(See note 2.)
EMC
Front panel operation parts
Conforms to IEC standards, equivalent to IP20 (when terminal cover mounted)
Terminals
Equivalent to VDE 0106/100 (when terminal cover mounted)
Radiated Emission:
Conducted Emission:
Immunity ESD:
Immunity-RF-interference:
Immunity Conducted Disturbance:
Immunity Burst:
EN61326 class A
EN61326 class A
EN61000-4-2:
4-kV contact discharge (level 2)
8-kV air discharge (level 3)
IEC1000-9-3:
10 V/m (amplitude modulated, 80 MHz to
1 GHz) (level 3)
10 V/m (pulse modulated, 900 MHz)
IEC1000-4-6:
10 V (0.15 to 80 MHz) (level 3)
IEC1000-4-3:
2-kV power-line (level 3)
2-kV I/O signal-line (level 4)
Approved standards
UL508, CSA22.2; conforms to EN50081-2, EN50082-2, EN61010-1 (IEC61010-1); conforms to
VDE106/part 100 (Finger Protection) when the terminal cover is mounted.
Memory protection
No protective functions (Communications data is not protected for power interruptions during
communications.)
Note:
1. A USB driver and communications software for the USB driver are required to use USB. This functionality is available with Windows 98/2000 only.
2. The enclosure ratings do not apply when USB is used.
2
K3SC
K3SC
Nomenclature
K3SC without Terminal Cover
Terminal Cover
Power Indicator
Lights (green) when
power is supplied.
Communications Status Indicators
Light (yellow) during communications.
RD: Lights when receiving RS-422/485
communications.
SD: Lights when sending RS-422/485
communications.
USB Port
Port for USB connections. Use this port
if the master device is a USB device.
Communications Setting Switch
Used to set the communications conditions for
connected devices.
Communications Setting Switch
Switch
1
2
3
4
5
6
7
8
9
10
Note: Cover the terminals to prevent electric shock.
Caution:
Be sure to use the K3SC-10 with
the terminal cover mounted
when using in machinery that
must conform to EN/IEC standards.
Setting
Baud rate
M3.5 Terminal Screw
Data length
Parity
Master device
Slave device
Echoback
Operation
■
Communications Settings Switch
Use this switch to set the communications conditions for the K3SC to those used by connected devices.
Setting
Baud rate
4,800
bps
9,600
bps
Data length
1,200
bps
2,400
bps
19,200
bps
38,400
bps
1
ON
OFF
ON
OFF
ON
OFF
2
OFF
ON
ON
OFF
OFF
ON
3
OFF
OFF
OFF
OFF
ON
ON
7
8
Stop bits
2
1
Parity
Even
Odd
None
Master device
Slave device
RS232C
RS485
USB
RS422
ON↔OFF
4
OFF
5
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
Note:
ON
ON
OFF
0
OFF
ON
7
9
ON
(with)
ON
6
8
Echoback
OFF
(without)
ON
All pins are factory-set to OFF.
3
K3SC
■
K3SC
Terminal Specifications
Be sure to check the input and output specifications for the signal pins of connected devices before connecting the terminals.
Function
For connecting the
operating power supply
Terminal
number
Name
1 and 4
PWR
Connection terminals for 3
RS-232C
5
communications with
6
master device
(DIP switch pin 8: OFF)
Used for RS-485
communications with
slave device
(DIP switch pin 9: OFF)
Used for RS-422
communications with
slave device
(DIP switch pin 9: ON)
Note:
■
Signal direction
---
Explanation
The input power supply specifications vary with the model.
A 100 to 240-VAC model and a 24-VAC/VDC (no-polarity)
model are available.
SG
---
Connect to signal ground.
SD
Input
Receives data from SD of the master device.
RD
Output
Sends data to RD of the master device.
8
RDA( −)
Input/output
9
SDA( −)
SD and RD for RS-485 (cold side)
Terminals 8 and 9 are connected internally when pin 9 of
the DIP switch is set to OFF.
11
RDB(+)
Input/output
12
SDB(+)
SD and RD for RS-485 (hot side)
Terminals 11 and 12 are connected internally when pin 9 of
the DIP switch is set to OFF.
Connect to signal ground.
7
SG
---
8
RDA( −)
Input
Receives RS-422 data and outputs it to the master side.
9
SDA( −)
Output
Converts data received via RS-232C from the master
device to RS-422 data and outputs the data.
11
RDB(+)
Input
Receives RS-422 data and outputs it to the master side.
12
SDB(+)
Output
Converts data received via RS-232C from the master
device to RS-422 data and outputs the data.
Terminals 2 and 10 are not used.
Internal Configuration (Block Diagram)
Indicator control
Switch input
RS-232C
RS-232C
driver
Power
indicator
Status
indicator
DIP switch
PHC
Serial
communications
Serial
communications
RS-485 driver
PHC
CPU
RS-485 enabling
control
PHC
USB
USB
controller
USB control
Insulation
4
Power
supply
RS-422 or
RS-485
K3SC
K3SC
Installation
■
External Connections
RS-485 Connection
RS-422 Connection
Slave device side
RS-422
Slave device side
RS-485
K3SC
7
8
9
10
11
12
(See note 1.)
(See note 1.)
K3SC
(-)
(+)
7
Master device side
RS-232C
4
Input power supply
(See note 2.)
1
5
6
SD
RD
2
3
SG
Note:
Abbreviation
SD
RD
SG
RS
CS
DR
ER
8
9
SG
RDA (-) SDA (-)
10
11
Abbreviation
SG
SDA (-)
SDB (+)
RDA (-)
RDB (+)
12
RDB (+) SDB (+)
Pin number (for 9-pin
computer connector)
3
2
5
7
8
6
4
Master device side
RS-232C
4
Input power supply
(See note.)
1. If RS-485 is selected as the communications method
(i.e., pin 9 of the DIP switch is set to OFF), terminals 8
and 9, and terminals 11 and 12 are connected internally.
1
5
6
SD
RD
2
3
SG
Note:
2. Either a 100 to 240-VAC or 24-VAC/VDC (no polarity)
input power supply is used.
Abbreviation
SD
RD
SG
RS
CS
DR
ER
Pin number (for 9-pin
computer connector)
3
2
5
7
8
6
4
Either a 100 to 240-VAC or 24-VAC/VDC (no polarity) input power supply is used.
Connection to an RS-232C Master Device
First set the same communications conditions (baud rate, stop bits, data length, and parity) for the master device, the Interface Converter,
and slave devices.
Devices connected
via RS-485 (example)
If the communications interface format
for the master device is RS-232C, set
pin 8 of the DIP switch to OFF.
AL1
AL2
HB
OT1 STP
OT2 CMW
Wire with
stranded wires.
Computer
Note:
K3SC
To allow connection using a commercially-available cable with an
RS-232C D-sub connector, a connection adapter (D-sub, 9-pin) is
available. (Order separately; model number: K32-23209.)
In addition to the required communications
conditions, set the communications number.
Note:
With RS-485 communications, connect a terminating resistance (120Ω, 1/2 W recommended) to both ends of the communications path (including the K3SC).
Connection to a USB Master Device
First set the same communications conditions (baud rate, stop bits, data length, and parity) for the Interface Converter and slave devices.
A USB driver and host software for
the driver are required.
Devices connected via
RS-485 (example)
If the communications interface
format for the master device is USB,
set pin 8 of the DIP switch to OFF.
AL1
AL2
HB
OT1 STP
OT2 CMW
K3SC
Computer
Remove the terminal
cover when using USB.
USB connection
In addition to the required communications
conditions, set the communications number.
Note: Use a commercially-available USB cable.
Note:
With RS-485 communications, connect a terminating resistance (120Ω, 1/2 W recommended) to both ends of
the communications path (including the K3SC).
5
K3SC
K3SC
Applications
Monitoring and Maintenance of Installations and Equipment
Computer
Temperature
Controller
K3SC
Interface
Converter
Digital Panel Meter
Inspections and Debugging for Communications Equipment
Computer
K3SC
Interface Converter
6
K3SC
K3SC
Installation Temperature Control with a Computer
Device interior
RS-232
15 m max.
RS-485
Mounting devices,
reflow devices, etc.
K3SC
Interface Converter E5ZN
Temperature Controller
Dimensions
K3SC-10
7
Mounting Hole Dimensions
(For Direct Mounting)
Two, M4 or 4.3-dia. holes
75
80
30
3
72±0.3
51.5
23.5
78
Note:
DIN track mounting is also possible.
7
K3SC
K3SC
Precautions
• Locations subject to temperatures or humidity outside the specified ranges
!Caution
Do not touch any of the terminals while power is being supplied. Doing so may result in electric shock.
• Locations subject to condensation or icing
• Locations subject to large amounts of dust
• Locations subject to flammable gases or objects
!Caution
Do not allow bits of metal or wire cuttings to enter the interior of
the product as this may result in malfunction, fire, or electric
shock.
!Caution
Do not attempt to disassemble, repair, or modify the product.
Any attempt to do so may result in malfunction, fire, or electric
shock.
• Locations subject to corrosive gases (in particular sulfide or ammonia gases)
Be sure to check power supply specifications, terminal numbers,
and polarities before performing wiring.
Turn OFF the power supply before performing installation or wiring.
Turn OFF the power supply before removing the terminal cover.
Do not connect anything to unused terminals.
Correct Use
!Caution
Tighten the terminal screws to the specified torque. Loose
screws may result in burning or malfunction. The recommended tightening torque is 0.78 N·m.
General Precautions
Do not mount the product in the following places:
• Locations subject to shock or vibration
Perform wiring with crimp terminals that are suitable for M3.5
screws.
Install the product as far away as possible from devices that generate strong high-frequency noise (e.g., high-frequency welders)
or surges.
Do not pull on the USB cable. Doing so may cause the cable to
come loose.
• Outdoor locations or locations subject to direct sunlight, wind, or
rain.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. N104-E1-1
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
Measuring and Supervisory Controls Department
Shiokoji Horikawa, Shimogyo-ku
Kyoto, 600-8530 Japan
Phone: (81)75-344-7108 Fax: (81)75-344-7189
8
Printed in Japan
0601-1M (A)