Important Safety Instructions .. 2
Precautions ............................... 3
Features..................................... 4
Digital Media Transport
ND-S1
Supplied Accessories................ 5
Instruction Manual
Getting to Know the ND-S1 ..... 6
Using the Remote Controller ... 7
Connecting the ND-S1.............. 8
Playing the Music and Videos on
Your iPod .................................10
Syncing Your iPod to Your PC.. 12
Thank you for purchasing an Onkyo product. Please
read this manual carefully before making any connections or using this product. By following these
instructions, you’ll get the best audio performance
and the most listening pleasure from your Onkyo
product. Keep this manual for future reference.
Playing the Music on Your PC
Through the ND-S1.................13
Troubleshooting .....................14
Specifications..........................15
En
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
2
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete
outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
Only use attachments/accessories specified by
the manufacturer.
Unplug this apparatus during lightning storms
or when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
14. Damage Requiring Service
Unplug the apparatus from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have
fallen into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally
by following the operating instructions.
Adjust only those controls that are covered
by the operating instructions as an improper
adjustment of other controls may result in
damage and will often require extensive
work by a qualified technician to restore the
apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in any way, and
F. When the apparatus exhibits a distinct
change in performance this indicates a need
for service.
Precautions
1. Recording Copyright—Unless it’s for personal
use only, recording copyrighted material is illegal without the permission of the copyright
holder.
2. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a
soft cloth dampened with a weak solution of
mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use
abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering.
3. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your
hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your
Onkyo dealer.
4. Do not use other AC adapters, car power adapters, or battery holders containing regular or
rechargeable batteries, as they may damage the
product.
For U.S. models
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES
WITH CANADIAN ICES-003.
Modèle canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE LA
CLASSE B EST CONFORME À LA NORME NMB-003 DU
CANADA.
For some models
Before use, connect the appropriate AC plug adapter
to the AC adapter.
The type of plug adapter depends on the place of
purchase.
Disconnect
Connect
FCC Information for User
CAUTION:
The user changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
Notch
For European Models
Declaration of Conformity
We, ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
3
Features
■ With the Onkyo ND-S1 Digital Media
Transport, you can easily play the music
stored on your iPod through your Onkyo
audio system and enjoy great sound.
■ The ND-S1 processes the digital audio signal directly from your iPod for high-quality
digital audio output (optical or coaxial).
■ The built-in USB audio interface allows
you to output the music stored on your PC
digitally (optical or coaxial).
■ Music stored on your PC can be output digitally even when the ND-S1 is powered by
only the USB bus.1
■ Easily sync your iPod with your iTunes
music library on your PC.
■ If your iPod supports TV out, connecting
the ND-S1’s VIDEO jack to your TV or AV
receiver allows to you to enjoy videos.
■ In addition to the included remote controller, you can also use your Onkyo amp or AV
receiver’s remote controller.2
■ The ND-S1 charges your iPod while you
enjoy your music.
1. When powered by only the USB bus, some iPod
functionality is not available and your iPod will not
be charged, so always use the included AC adapter
when possible.
2. Only
-capable Onkyo amp and AV receiver
remote controllers are supported.
If the remote controller supplied with your Onkyo
amp or AV receiver has separate POWER ON and
STANDBY buttons, operation is as follows:
• When the amp or AV receiver is set to Standby,
only the amp or AV receiver turns On.
• When the amp or AV receiver is already On, the
ND-S1 turns On.
So to turn on the ND-S1 when the amp or AV
receiver is set to Standby, on the remote controller
supplied with your amp or AV receiver, you must
press the [ON] button twice.
4
Recommended iPod Models
• iPod nano (2nd generation)
• iPod nano (3rd generation)
• iPod classic
• iPod touch
• iPod nano (4th generation)
• iPod touch (2nd generation)
iPod Models with Limited Support:
• iPod nano
• iPod (5th generation)
* iPod is a trademark of Apple Inc., registered in the
U.S. and other countries.
“Made for iPod” means that an electronic accessory
has been designed to connect specifically to iPod
and has been certified by the developer to meet
Apple performance standards.
Apple is not responsible for the operation of this
device or its compliance with safety and regulatory
standards.
Notes:
• On the 5th generation iPod and iPod nano,
the click wheel is disabled during playback.
Use the ND-S1’s [iPod] button to start and
stop playback and the remote controller to
control other iPod functions.
• Before using the ND-S1, update your iPod
with the latest software, available from the
Apple Web site at: www.apple.com
• The instructions in this manual apply to
iPod models as of June 2009 and may
change with future upgrades to the iPod
software.
• Several generations of some iPod models
have been sold. An iPod without “xxx generation” in its name indicates the first generation of that particular iPod.
• The AC adapter supplied with the ND-S1 is
designed exclusively for use with the
ND-S1. Do not use it with any another
device. Likewise, do not use any other AC
adapter with the ND-S1. Doing so may
damage the ND-S1.
Supplied Accessories
Make sure you have the following accessories.
• AC adapter
• Optical audio cable
• USB cable
• Remote controller
/ Y
N B
O D
N
TA
S
o
iP
d
/P
C
/
C C
N
Y N
S SY
N
U
PLAY
LIS
T
SH
UF
FLE
A
L
U
B
M
REP
T
EA
R
C
-7
55
E
• Video cable
•
cable
• Instruction Manual
* In catalogs and on packaging, the letter at the end
of the product name indicates the color. Specifications and operations are the same regardless of
color.
5
Getting to Know the ND-S1
sync has been cancelled. While the indicator
is flashing, you cannot operate any buttons
or start iPod playback. See page 12 for
details.
Front and Top
iP
od
P
C
U SY
N N
S C
Y /
N
C
Rear Panel
T
OR
SP
Y
DB
Y
DB
STAN
1
AN
od
iP
TR
AN
/ST
ON
1 23 4
7
6
5
1 ON/STANDBY button
Sets the ND-S1 to On or Standby.
2 Remote control sensor
Receives control signals from the remote
controller.
3 STANDBY indicator
Lights up when the ND-S1 is on Standby. If
your iPod is charging during Standby, it
flashes slowly.
4 iPod dock connector
Connects to your iPod.
5 iPod button/indicator
Press this button to use your iPod. Press
repeatedly to start and stop iPod playback.
The indicator lights up blue when your iPod
is selected.
6 PC button/indicator
With the ND-S1 connected to your PC via
USB, press this button to output the music
stored on your PC digitally from the ND-S1.
The indicator lights up green when your PC
is selected.
7 SYNC/UNSYNC button/indicator
With the ND-S1 connected to your PC via
USB, and your iPod inserted in the ND-S1,
press this button to sync your iPod with your
iTunes music library on your PC. The indicator lights up red while sync is in progress.
To cancel sync, press and hold this button
for at least 2 seconds. The indicator will flash
for a few moments and stop flashing when
6
1
23
4 5 6
REMOTE CONTROL jack
Connects to the
jack on another
capable Onkyo component for linked operation. This connection should not be used
with some components. See page 8 for
details.
2 OPTICAL AUDIO OUT jack
This optical digital audio output jack connects to an optical digital audio input on a
system component, amp, or AV receiver.
3 COAXIAL AUDIO OUT jack
This coaxial digital audio output jack connects to a coaxial digital audio input on a
system component, amp, or AV receiver.
4 USB port
Connects to a USB port on your PC for playing music stored on your PC and iTunes
sync.
5 VIDEO OUT jack
Connects to a composite video input on
your TV or AV receiver for video playback.
6 DC IN 5V 1A jack
Connect the included AC adapter here.
Using the Remote Controller
Aiming the Remote Controller
Replacing the Battery
The included remote controller uses a CR2025
type battery. Always use with the same type.
RC
-75
5E
1. To open the battery
compartment, press
the small hollow and
slide open the cover.
Remove the battery-protect tab before use.
Point the included remote controller toward
the ND-S1’s remote control sensor, as shown.
Remote control sensor
Y
DB
AN
/ST
ON
m
.5
rox t.)
p
Ap (16 f
ND-S1
Y
DB
AN
ST
iPod
PC
2. While pressing the
tab as shown, slide
out the old battery.
3. Slide the new battery
into the compartment with the positive (+) side facing up.
UNSSYN
YNCC/
30°
30°
4. Slide the cover shut.
STA ON/
NDB
Y
iPod
/PC
SYN
UNS
C/
YNC
PLAY
LIST
SHUF
FLE
ALB
UM
REPE
AT
RC-
755E
Notes:
• The remote controller may not work reliably
if the ND-S1 is subjected to bright light, such
as direct sunlight or inverter-type fluorescent lights. Keep this in mind when installing.
• If another remote controller of the same type
is used in the same room, or the ND-S1 is
installed close to equipment that uses infrared rays, the remote controller may not work
reliably.
• Don’t put anything on top of the remote controller, such as a book or magazine, because a
button may be pressed continuously,
thereby draining the battery.
• The remote controller may not work reliably
if the ND-S1 is installed in a rack behind colored glass doors. Keep this in mind when
installing.
• The remote controller will not work if there’s
an obstacle between it and the ND-S1’s
remote control sensor.
Notes:
• If the remote controller doesn’t work reliably,
try replacing the battery.
• If you intend not to use the remote controller
for a long time, remove the battery to prevent damage from leakage or corrosion.
• An expired battery should be removed as
soon as possible to prevent damage from
leakage or corrosion.
• Misuse of lithium batteries may cause a fire
or chemical burn. Always keep out of reach
of children. Never disassemble, charge, heat
above 100°C, or incinerate.
CAUTION:
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent type.
7
Connecting the ND-S1
Connecting an Amp or AV Receiver
Connect the ND-S1 to a digital audio input on
your Onkyo amp or AV receiver that can be
assigned to an input selector whose Input Display can be set to “DOCK.” Setup varies
depending on your particular amp or AV
receiver model. Refer to the Digital Input Setup
and Changing the Display sections of your amp
or AV receiver’s instruction manual for details.
TV
PC
1. Using the included optical audio cable,
connect the ND-S1’s OPTICAL AUDIO OUT
jack to an optical digital audio input jack
on your amp or AV receiver.
2. If your iPod supports TV out, use the
included video cable to connect the
ND-S1’s VIDEO OUT jack to a composite
video input on your TV or AV receiver.
3. Using the included
cable, connect the
ND-S1’s
REMOTE CONTROL jack to an
jack on your amp or AV receiver.
4. Connect the included AC adapter to the
ND-S1’s DC IN 5V 1A jack, and plug the AC
adapter into a suitable wall outlet.
VIDEO
INPUT
USB cable
ND-S1
Optical digital
audio cable
cable
AV receiver
8
Video
cable
To
wall
outlet
AC adapter
Notes:
• The ND-S1’s audio outputs are digital outputs. If the digital audio input on your amp or
AV receiver cannot be assigned to an input
selector whose Input Display can be set to
“DOCK,” do not connect the
cable, otherwise a malfunction may occur.
• Do not place the ND-S1 on top of a component that gets warm or one with has air vents
on top, as it may interfere with that component’s cooling or cause the component or
ND-S1 to overheat. Place it next to the component, use an audio rack, etc.
Inserting Your iPod into the ND-S1
Prepare the adapter that came with your iPod.
iP
od
P
C
U SY
N N
S C
Y /
N
C
1. Gently push down and slide open the dock
cover on the ND-S1.
T
OR
SP
AN
Y
DB
Y
DB
od
iP
STAN
TR
AN
/ST
ON
2. Insert the adapter supplied with your iPod,
then push your iPod firmly onto the
ND-S1’s dock connector.
■ Removing the iPod Adapter
To remove the iPod adapter from the ND-S1,
insert a small flathead screwdriver into the slot,
and lift it out, as shown below.
iP
od
PC
UN SY
SY NC
NC /
Adapter supplied
with iPod
Notes:
• If the [iPod] indicator does not light up after
you’ve inserted your iPod, this means that
your iPod is not properly seated on the dock
connector. Make sure your iPod is seated
properly on the dock connector.
• To prevent dock connector damage, don’t
twist your iPod when inserting or removing
it, and be careful not to knock your iPod
while it’s inserted.
• Don’t use your iPod with any other accessories, such as FM transmitters and microphones, because they may cause a
malfunction.
T
OR
SP
Y
NDB
STA
ON/
Y
NDB
STA
AN
d TR
iPo
Notes:
• If you use a case with your iPod, always
remove it before you insert it. Otherwise, it
may not connect properly and a malfunction
may occur.
• Do not insert your iPod into the ND-S1 without the adapter that came with it, as it may
put unnecessary strain on the iPod or
ND-S1’s dock connector, causing permanent
damage.
When you insert your iPod, the ND-S1 works as
follows depending on the status of your iPod.
• iPod not playing:
The ND-S1 starts charging your iPod and the
STANDBY indicator flashes slowly.
• iPod playing:
The ND-S1 turns on, the [iPod] indicator
lights up blue, and your iPod continues playing.
9
Playing the Music and Videos on Your iPod
Music and Video Playback
1. On your iPod, select the song or video you
want to play.
2. Insert your iPod into the ND-S1 (see page
9).
3. Press the remote controller’s Play/Pause
[L] button, or the ND-S1’s [iPod] button
to start playback.
See below for additional remote controller
operation and system functions.
Remote Controller Button Operation
You can use the following buttons to control
your iPod. Actual operation may vary depending on your iPod model, its generation, and
firmware version.
1
2
3
ON/
STANDBY
iPod/PC
SYNC/
UNSYNC
PLAYLIST
ALBUM
SHUFFLE
REPEAT
7
4
5
6
8
9
RC-755E
1 ON/STANDBY button
Sets the ND-S1 to On or Standby.
2 iPod/PC button
Press repeatedly to select your iPod or PC.
3 Previous/Next [t]/[Y] buttons
During playback or while playback is
paused, press the Next [Y] button to
10
select the next song. Press the Previous [t]
button to return to the beginning of the current song, press again to select previous
songs.
Press and hold to fast forward or rewind.
4 Play/Pause [L] button
Press to start playback on your iPod. Your
iPod will turn on automatically if it’s not
already on. Press the button again to pause
playback.
5 PLAYLIST Up/Down [B]/[N] buttons
If your iPod contains playlists, press the
PLAYLIST Up [B] button to select the previous playlist. Press the PLAYLIST Down [N]
button to select the next playlist on your
iPod.
6 SHUFFLE button
Press repeatedly to set the shuffle function
on your iPod (Song, Album, or Off ).
7 SYNC/UNSYNC button
Press to start or cancel iPod sync. The indicator shows the current status.
8 ALBUM Up/Down [B]/[N] buttons
Used to change albums.
To change album, start album or all song
playback, then press the ALBUM Up/Down
[B]/[N] buttons.
9 REPEAT button
Press repeatedly to set the repeat function
on your iPod (One, All, or Off ).
Some of the iPod functions that you can control
with this remote controller can also be controlled with the remote controller that came
with your amp or AV receiver. Refer to the
instruction manual that came with your amp or
AV receiver for details.
See pages 8 to 9 for connection information.
System Functions
You can use the following system functions:
■ System On
When you turn on your amp or AV receiver, the
ND-S1 and iPod turn on automatically. In addition, when the ND-S1 and iPod are on, some
amps and AV receivers can be turned on by
pressing the [ON/STANDBY] button.
■ System Off
When you turn off your amp or AV receiver, the
ND-S1 and iPod automatically go on Standby.
■ Timer Off
If you set your amp or AV receiver’s sleep timer,
the ND-S1 and iPod will automatically switch to
Standby at the specified sleep time.
■ Timer Play
If you set your amp or AV receiver’s play timer,
the ND-S1 and iPod will automatically turn on
and your iPod will start playback at the specified time.
■ Auto Power On
If you press the remote controller’s Play/Pause
[L] button while your amp or AV receiver is
on Standby, your amp or AV receiver will turn
on automatically, select your iPod as the input
source, and your iPod will start playback.
Notes:
• Linked operations do not work with video
playback or when the alarm is set to play a
sound.
• If you use your iPod with any other accessories, iPod playback detection may not work.
■ Operating Notes
• Use your amp or AV receiver’s volume control to adjust the playback volume.
• While your iPod is inserted in the ND-S1, its
volume control has no effect.
• If you do adjust the volume control on your
iPod while it’s inserted in the ND-S1, be
careful that it’s not set too loud before you
reconnect your earphones.
Note:
• On the 5th generation iPod and iPod nano,
the click wheel is disabled during playback.
Use the ND-S1’s [iPod] button to start and
stop playback and the remote controller to
control other iPod functions.
■ Direct Change
if you start iPod playback while listening to
another input source, your amp or AV receiver
will automatically switch to the input to which
the ND-S1 is connected.
■ Other Remote Controllers
You can use the remote controller that came
with your amp or AV receiver to control other
iPod functions. The available functionality
depends on your amp or AV receiver. See the
instruction manual that came with your amp or
AV receiver for details.
■ iPod Alarm
If you use the Alarm function on your iPod to
start playback, your amp or AV receiver will turn
on at the specified time and select your iPod as
the input source automatically.
11
Syncing Your iPod to Your PC
You can transfer songs and videos from your
iTunes music library on your PC to your iPod by
using sync. (Videos are restricted to iPod models that support video.)
1. Using the included USB cable, connect the
ND-S1’s USB port to a USB port on your PC.
2. Press the [SYNC/UNSYNC] button.
The indicator lights up red, iTunes opens on
your PC, and sync starts.
ND-S1
ON/
STANDBY
iP
od
PC
UN SY
SY NC
NC /
Remote controller
iPod/PC
SYNC/
UNSYNC
T
OR
SP
Y
NDB
STA
ON/
Y
NDB
STA
AN
d TR
iPo
SYNC/UNSYNC
button
SYNC/UNSYNC
button
Note:
• In the iTunes settings, if the “Automatically
sync when this iPod is connected” option is
not selected, iTunes will not open automatically and you’ll have to start iTunes manually.
Note:
Follow the steps below if you want to cancel
sync. Failure to follow these steps may result
in data loss or malfunction.
1. In iTunes, click the Eject button to eject
your iPod.
2. Press and hold the [SYNC/UNSYNC] button for at least 2 seconds.
After a few moments, the
[SYNC/UNSYNC] indicator flashes, indicating sync has been cancelled.
12
■ iTunes Restore Function
If iTunes detects any damaged data on your
iPod, it will attempt to restore it. When the
restore process is complete, the ND-S1’s sync
function may cancel automatically, in which
case you’ll need to press the [SYNC/UNSYNC]
button again to sync.
The following operating systems are supported: Windows XP, Windows Vista.
* iTunes is a trademark of Apple Inc., registered in the
U.S. and other countries.
* Windows and Windows Vista are either registered
trademarks or trademarks of Microsoft Corporation
in the United States and/or other countries.
Playing the Music on Your PC Through the ND-S1
By connecting the ND-S1 to a USB port on your
PC, you can play the music stored on your PC
through your Onkyo audio system.
1. Using the included USB cable, connect the
ND-S1’s USB port to a USB port on your PC.
2. Press the ND-S1’s [PC] button, or the
[iPod/PC] button on the included remote
controller to select PC.
The [PC] indicator lights up green.
Remote controller
ON/
STANDBY
iP
od
PC
UN SY
SY NC
NC /
ND-S1
iPod/PC
SYNC/
UNSYNC
T
OR
SP
NDB
STA
ON/
Y
Y
NDB
STA
AN
d TR
iPo
PC button
iPod/PC button
3. Start music playback on your PC.
Use your amp or AV receiver’s volume control to adjust the playback volume.
Note:
• If the ND-S1 is not recognized as a USB audio
device even after restarting your PC, in the
Control Panel, open “Sounds & Audio
Devices” and select “USB Audio DAC” as the
default sound playback device. For more
information, see the “Sound Troubleshooter”
in Windows Help.
13
Troubleshooting
No Sound or Video
• Make sure your iPod is connected properly.
• If there’s no video, make sure you iPod supports TV out.
• Make sure your iPod is playing.
• Make sure your amp or AV receiver is turned
on, the input to which the ND-S1 is connected is selected as the input source, and
the volume control is not set to minimum.
• Make sure all plugs are pushed in all the way.
• Make sure the ND-S1 is connected to the correct input jacks on your amp or AV receiver. If
there’s no video, check your video connections. Do not connect the ND-S1 to any jacks
on your amp or AV receiver labeled OUT.
• Make sure the AC adapter is properly connected to the ND-S1 and a suitable wall outlet.
• Try resetting your iPod.
• If you remove then re-insert your iPod, it may
not be recognized temporarily. In this case,
press and hold down the ND-S1’s [iPod] button for at least 2 seconds to reset the ND-S1.
If it’s still not recognized, disconnect the USB
cable and AC adapter, then reconnect them.
14
Remote Controller doesn’t work
• Make sure your iPod is seated properly on
the dock connector. If your iPod is in a case, it
may not connect properly, so always remove
the case before inserting your iPod into the
ND-S1.
• Your iPod cannot be controlled while it’s displaying the Apple logo.
• If your remote controller has Remote Mode
buttons, make sure the mode necessary to
control your iPod is selected.
• If you’re using the remote controller that
came with your amp or AV receiver, be sure
to point it toward your amp or AV receiver
when you want to control your iPod.
• An
cable connection is required with
some components, but not others. If you
connect it by mistake, remote control may
not work. See page 8 for details.
• Try resetting your iPod.
Others
• Before using one of the other components
connected to your amp or AV receiver, stop
playback on your iPod. If playback is not
stopped, the Direct Change function may
select your iPod as the input source by mistake at the transition between songs.
• Depending on the backlight setting on your
iPod, the display may become dim during
use. If the display is hard to see, change the
backlight setting on your iPod.
• Do not use Cover Flow while playing music
on your iPod, as it may stop iPod playback or
cause noise.
Specifications
Power supply:
100–240 V AC
adapter (5V/1A)
Power consumption:
3.5 W
USB consumption:
250 mA
Standby consumption: Less than 0.4 W
Dimensions (W x H x D): 8-1/16 x 1-3/8 x 6-7/8
inches
205 x 35 x 175 mm
Weight:
1.17 lbs. (530 g)
Jacks:
Optical digital audio
output, coaxial digital
audio output, composite video output,
USB port,
jack
■ PC System requirements
• Windows XP (SP2 or later) or Windows Vista
• 1 GHz or faster processor
• At least 512 MB of memory
• 200 MB of free hard drive space to install
iTunes (additional free space required to
store music and videos)
• DirectX 9.0 compatible graphics adapter
• At least 32 MB of video memory
• 1024 x 768 or higher display resolution
• Internet connection
Specifications and appearance are subject to change
without notice.
15