Keypad - dorma

DORMA
Installation Manual
Keypad
blank page
Keypad-DP1/DCW
Table of Contents
Table of Contents
1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3 Keypad connections . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3.1 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.2 Correct use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.4 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.3 Safety instructions and warnings . . . . . . . . . . . . . 5
2.4.1 DIP switch on the power supply board . . . . . . . . . 10
1.4 Further Source of Information . . . . . . . . . . . . . . . 6
2.4.2 DCW mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.5 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4.3 DP1 mode (RS485) . . . . . . . . . . . . . . . . . . . . . . 11
1.6 Functional principle of the keypad . . . . . . . . . . . . . . 6
3 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.7 Interfaces and protocol variants . . . . . . . . . . . . . . . 6
3.1 Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.8 Components supplied . . . . . . . . . . . . . . . . . . . . . . . 7
3.1.1 Key functions of the keypad unit . . . . . . . . . . . . 12
1.9 Design of the keypad . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Visual displays . . . . . . . . . . . . . . . . . . . . . . . . . 12
2 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.2.1 LED displays in the keypad unit . . . . . . . . . . . . . 12
2.1 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3 Acoustic signals . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1.1 Installation regulations for the switch boxes . . . . . . 8
EU Declaration of conformity . . . . . . . . . . . . . . . . . . . 13
2.1.2 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.2 Final assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Keypad-DP1/DCW
1. General information
The information provided in this installation guide may be
modified without prior notification. All previous versions
cease to be valid with the publication of this mounting
guide.
The information in these assembly instructions has been
compiled to the best of our knowledge and in good faith.
DORMA Time + Access GmbH accepts no liability for the
correctness or completeness of the information provided.
In particular, DORMA Time + Access GmbH cannot accept
liability for any consequential damage due to incorrect or
incomplete information.
DORMA Time + Access GmbH accepts no liability for the
perfect functioning of the keypad in environments outside
the system.
Despite every effort to prevent mistakes, they can never
be completely avoided. Therefore, we would be grateful to
receive notification of any errors or omissions.
DORMA Time + Access GmbH accepts no liability for the
information included in this document being free of protected third-party rights.
DORMA Time + Access GmbH does not provide any licences
to its own or to third party patents or other protected rights
with this document.
The recommendations for installation provided in this manual are based on favourable basic conditions being present.
It is not permissible to print, reproduce or pass this manual, or parts thereof, to third parties, other than for your own use,
without the approval of DORMA Time + Access GmbH.
All rights reserved.
DORMA Time + Access GmbH
PO box 21 01 85
53156 Bonn, Germany
http://www.dorma-time-access.de
E-mail: info@dorma-time-access.de
© Copyright 2007 by DORMA Time + Access GmbH
drawing no.: 1059G-00-B1
as at: 01/11 V1.05
Keypad-DP1/DCW
1. General information
1.1 Preface
This installation manual is intended to assist you in connecting and commissioning the keypad. Information or drawings
going beyond the content of this manual are available on
request.
1.2 Correct use
This device is intended exclusively for use in time recording
and access control systems. Further details are described
in chapter 1.4. Any use other than that indicated is not
permitted!
1.3 Safety instructions and warnings
This unit has been constructed and tested in accordance
with the relevant current technical regulations. It left the
factory in perfect condition in terms of safety and reliability.
To maintain this condition and to ensure risk-free operation,
the instructions and warnings given in this installation guide
must be observed by the user.
• The device may only be used for the purpose intended by
the manufacturer.
• Fitting and installation of electrical equipment may only
be carried out by an electrician.
• Before opening the unit, always switch off the power supply and check that it is inactive by measuring.
• During mounting, please ensure that the requirements
laid down in the relevant equipment safety standard for
the unit are adhered to since violating them could affect
the safety of the device.
• Before switching on, ensure that the operating and control voltages connected do not exceed the permissible
values, in accordance with the technical data.
• This unit conforms to EN 60950-1 protection class III
Electromagnetic compatibility:
• The unit is designed for use in residential, business and
commercial areas and conforms to EN 61000-6-2 and
61000-6-3.
• The PCB can be damaged by static electricity discharge,
so the relevant precautionary measures must be observed
(grounding etc.).
Caution
• These units may only be operated when mounted.
• The locking screws on unassigned connection terminals
must be screwed in as far as they will go.
• If it must be assumed that danger-free operation is no
longer possible, take the unit out of operation and secure
it against accidental use.
• If there is a possible danger to people or animals or of
damage to operating equipment due to the failure or
malfunction of the unit, this must be prevented by taking
additional safety measures (limit switches, safeguards
etc.).
General Installation Guidelines
see manual 1006G-B0
Keypad-DP1/DCW
1. General information
1.4 Further Sources of Information
Planner Manual
Examples of cross-system solutions
Further documents are available on request.
General Installation Guidelines
Specifications for planning attendance recording and
access control systems with our wired components.
Catalogues
1.5 Disposal
Information for EU Countries
European Directive 2002/96 EC applies to this device.
This means that this product must not be disposed of with
normal household waste. We, the manufacturer, will take
back our electric and electronic products and dispose of
them for you free of charge. Correct disposal of your old
equipment protects people and the environment from
possible harmful consequences.
ST102
The device was manufactured using recyclable materials and
components.
When disposing of the device and the packaging, please
ensure environmentally friendly recycling.
1.6 Functional principle
The keypad is offered for use in DCW mode in two electronically different versions.
Either as a simple PIN keypad or as a PIN keypad with an
integrated contactless reader for the secure identification of
persons.
The difference can be recognised by the description on the
name plate.
In the DP1 model there is always a reader.
KP-D-6-XX-PX10-DC-0-0--24V
20V-28VDC,max.0,96W XX
XXXXXXXX-XXXXX-XXX XX
KP-D-6-XX-00-DC-020V-28VDC,max.0,
XXXXXXXX-XXXXX-
with reader
Depending on the model, persons
are identified by simply
KP-D-6-XX-PX10-DC-0-0--24V
20V-28VDC,max.0,96W
entering a PIN number or by holding
an ID card in front XX
as well. The electronics evaluate theXXXXXXXX-XXXXX-XXX
data and send it to a XX
superordinate control unit.
with reader
The keys of the keypad are illuminated in the dark. A light
sensor controls the background illumination.
without reade
KP-D-6-XX-00-DC-0-0--24V
20V-28VDC,max.0,96W XX
XXXXXXXX-XXXXX-XXX XX
5P9EN2N1
without reader
1.7 Interfaces and protocol variants
Depending on the firmware employed, the keypad always
supports only one interface with a particular protocol.
The interface and protocol supported can be seen from the
type code on the nameplate.
Code
Schnittstelle
Protokoll
DC
P1
DCW
RS485
DCW
DP1
KP-D-6-XX-XX-##-0-0--24V
16V-6VDC,max.1,2W XX
XXXXXXXX-XXXXX-XXX XX
1. General information
Keypad-DP1/DCW
1.8 Components supplied
A 1x keypad
B 1x manual
A
B
DORMA
Installation Manual
Keypad
1.9 Design of the keypad
The keypad consists of a keypad unit and the power supply
unit.
Power supply unit
The power supply unit consists of an assembly board and a
power supply board. The assembly board is for securing the
unit in the switch terminal box. It holds the power supply
board. The power supply board creates the voltage required
internally from the power supply and provides the connection to the DP1/DCW bus.
The keypad unit includes the keys with background illumination and the complete control system. It is mounted
on the power supply unit. The electric connection is made
through a knock-out section in the mounting board to a plug
on the power supply board.
The device is delivered without a combination frame.
In this way, users can use a frame from the respective range
of switches suiting their own series.
Keypad unit
Keypad-DP1/DCW
2. Installation
2.1 Preparation
The keypad must be mounted in a sheltered environment,
i.e. within a closed room.
Because of the contactless ID card reading process, there
must not be any metallic objects within a square area measuring 120 mm x 120 mm and with a depth of 30 mm.
Appropriate distances must be ensured when planning and
installing. The reading range will be reduced if it is not possible to comply with these distances.
To prevent interference from both sides, two readers may
not be installed closer to each other than the minimum
specified distance.
This minimum distance depends on local conditions.
It should always be greater than 50 cm.
The wiring for the connections should be made in advance.
2.1.1 Installation regulations for the switch boxes
Flush-fit switch boxes must not lie more than 4 mm
beneath the surface of the wall or the plaster and must be
positioned vertically in the wall. The front edge must be
parallel to the wall surface or only deviate by a maximum
of 1.5 mm. Flush-fit boxes that are not correctly mounted
must be removed and re-mounted.
28
min. 40
2.1.2 Wiring
Due to the connection terminals, only lines with a max.
cross-section of 1 mm² can be connected.
Twisted pair cables with a characteristic impedance of
120 Ω are to be used for the data lines.
Detailed information about types and lengths of the cables
as well as further information about planning access control
systems with our components are contained in the
General Installation Instructions Series 6.
(Part no. 1900004912336)
2.2 Final assembly
The keypad is delivered fully assembled. To connect it, first
remove the keypad unit by simply pulling it off.
Before installing the power supply unit, please connect the
two DP1/DCW plug connectors ST101 and ST104 to the
power supply board (see page 8).
After positioning correctly, the power supply unit can be
inserted into the box and fixed in place with the screws.
The combination frame is positioned between the fitted
power supply unit and the keypad unit. Then connect the
keypad unit. Please make sure that the plug connection has
been made correctly.
Please note: Before taking into operation for the first time,
you must configure the address before connecting the keypad unit.
Please note: The keypad has no built-in tamper detection.
Instead, the software monitors the online status and detects whether the keypad unit has
been removed.
Keypad-DP1/DCW
2. Installation
2.3 Keypad connections
1
3
4
10
ST
A
B
10
4
A
B
W
1/
DC
B
W
DP
3
1
DC
1/
System current = Sum of all currents drawn from the
power supply unit or super ordinate control unit.
A
DP
1)
CW
DP
1/
D
1
3
ST
1
10
CW
ST
3
1
B
A
D
1/
DP
Warning: Ensure that the system current1) is not higher
than the admissible total current of the power supply unit
employed.
ST
10
1
2.3.1 Power supply
The power supply to the keypad is connected to terminal 1
and terminal 3 of the ST101. ST104 serves as the connection for other bus devices.
The pin assignment of ST101 is identical to ST104.
The voltage must lie in the range of 16 V to 36 VDC.
2.3.2 Communication interfaces
The function of the communication interface depends on
the firmware employed (see section 1.5).
DCW bus
The DCW bus line is connected to the connection terminals
ST101 and ST104, signals A and B.
4
0V
3
B
0V
B
W
DC
s
bu
B
us
V
24
V
A
24
A
0V
V
24
B
rb
he
Ot
us
rb
he
Ot
A
A
1
24
V
3
0V
A1
B
B
BA
A
A
1
1ST
10
4
10
ST
11
1100
SSTT
33
B
RS485 bus (DP1)
The RS485 connection is identical with the DCW connection.
/
P1
D
W
s
bu
DC
/
P1
D
2. Installation
Keypad-DP1/DCW
gelichtschranke
2.4 Settings
Preface: The settings, operation and displays are dependent on the configuration in the access control system. The
status conditions described here reflect the normal status of
the access control system on delivery.
2.4.1 DIP switch on the power supply board
The DP1/DCW bus address can be set with the 2-pin DIP
switch (accessible from the front of the power supply unit).
Please note: If the keypad is already connected, the keypad unit can be raised slightly with a screwdriver or similar object and pulled off.
ST101
SW101
2.4.2 DCW mode
Switch 101
1
2
Bus adress
Functionality
3
4
Not used
5
6
Reading process
7
8
Bus connection
resistor
1)
Default
off
off
on
off
off
off
off
off
adjustable


x



x
x
00
off
off
01
on
off
02
off
on
03
on
on
Address
(decimal)
Switch 101
10
1)
Reading process only with DCW reader
Reading variants
4
5
6
Keypad
off
off
off
Combined (Hitag1, Hitag2, EM4102, EM4450)
off
off
on
not permitted
off
on
off
Hitag2
off
on
on
EM4450
on
off
off
Hitag1
on
off
on
EM4102
2. Installation
Keypad-DP1/DCW
2.4.3 DP1 mode (RS485)
Switch 101
Function in RS485 mode
1
2
Functionality
3
4
5
Bus address
6
Not used
7
8
Bus connection
resistor
Default
on
off
off
off
off
off
off
off
adjustable





x


00
off
off
off
off
off
01
on
off
off
off
off
02
off
on
off
off
off
03
on
on
off
off
off
04
off
off
on
off
off
05
on
off
on
off
off
06
off
on
on
off
off
07
on
on
on
off
off
08
off
off
off
on
off
09
on
off
off
on
off
10
off
on
off
on
off
11
on
on
off
on
off
12
off
off
on
on
off
13
on
off
on
on
off
14
off
on
on
on
off
15
on
on
on
on
off
16
off
off
off
off
on
17
on
off
off
off
on
18
off
on
off
off
on
19
on
on
off
off
on
20
off
off
on
off
on
21
on
off
on
off
on
22
off
on
on
off
on
23
on
on
on
off
on
24
off
off
off
on
on
25
on
off
off
on
on
26
off
on
off
on
on
27
on
on
off
on
on
28
off
off
on
on
on
29
on
off
on
on
on
30
off
on
on
on
on
31
on
on
on
on
on
Address
(decimal)
11
Keypad-DP1/DCW
3. Commissioning
3.1 Keypad
3.1.1 Key functions of the keypad unit (only DCW)
The keys are only used for entering a PIN (max. 8 digits).
Incorrect entries can be deleted with the * key (complete
entry). After completing the entry, the number can be transmitted to the access control system with the # key.
If neither of the two keys is pressed within 5 seconds,
the complete entry is deleted and a short acoustic signal
sounds.
ID card identification
Status LED
In DP1 mode - no restriction to 8 digits. * and # keys can
be allocated freely by the system.
3.2 Visual displays
3.2.1 LED displays in the keypad unit
The yellow status LED, on the left in the keyboard unit, is lit
while the keypad is online. It goes out if it is not polled for
longer than 7 seconds (DP1) or 15 seconds (DCW).
The right bicolour LED shows the access identification. It
a) flashes briefly in orange when an ID card is read. This
function is independent of the communication with an
access control system.
b) lights green if the authorisation is identified.
c) flashes green for 10 seconds if a PIN is demanded in
addition to the ID card identification. The PIN must be
entered within this time.
d) lights red for 1 second if an ID card is read and identified as unauthorised.
Points b) to d) can be changed in DP1 mode
3.3 Acoustic signals
a) A short key click sounds when a key is pressed in the
keypad unit.
b) The buzzer sounds for 1 second with a continuous tone
when the authorisation is identified.
c) The buzzer sounds intermittently for 1 second if access
authorisation is not granted.
(Points b) and c) can be changed in DP1 mode).
12
Light sensor
Keypad-DP1/DCW
EG Konformitätserklärung
EC Declaration of Conformity
CE Déclaration de conformité
13
Keypad-DP1/DCW
4. Technical data
Technische Daten
Versorgungsspannung
16 V bis 36 V DC (SELV)
Lagertemperatur
–20°C bis +70°C
Leistungsaufnahme
max. 40 mA bei 24 V, max. 0,96 W
Allgemeine Auslegung
EN 60 950-1, Schutzklasse III
Leseabstand
max. 6 cm
(bei Geräte mit integriertem Leser)
Schutzart
IP 30
Sende-Frequenz
HITAG: 125,00 kHz
Schnittstellen
DCW-Bus oder
RS485-Bus (DP1)
Anzeigeelemente
1x LED (online)
1x LED (read, Status PIN-Eingabe)
1x Akkustischer Signalgebe
Störfestigkeit
EN 301 489-3
Störaussendung
EN 300 330
EN 301 489-1, -3
Abmessung
B71 x H71 x T24
Gewicht
68 g
Betriebstemperatur
–20°C bis +50°C
(keine Betauung zulässig)
Technische Änderungen und Verbesserungen, die dem Fortschritt unserer Geräte dienen, behalten wir uns vor.
DORMA Time + Access GmbH
Postfach 21 01 85 • D-53156 Bonn • Mainzer Straße 36-52 • D-53179 Bonn
Tel. +49 (0) 2 28/85 54-0 • Fax +49 (0) 2 28/85 84-1 75 • www.dorma-time-access.de
DORMA GmbH + Co. KG
Postfach 40 09 • D-58247 Ennepetal • DORMA Platz 1 • D-58256 Ennepetal
Tel. +49 (0) 23 33 / 793-0 • Fax +49 (0) 23 33 / 79 34 95 • www.dorma.com
14
Keypad-DP1/DCW
Notice
15