INSTALLATION INSTRUCTION InvisiLED® Indoor

INSTALLATION INSTRUCTION
InvisiLED® Indoor Controller
LED-TC-CTR-MSD
KEY SPECIFICATIONS:
Overall dimensions: Min/max run length:
Power Supply:
Current: 3 11/16” x 2 1/4” x 1” (94mm x 57mm x25mm)
Under 24V 60W DC power supply, it can control 40ft of INVISILED® Palette.
24V DC power supply, Class II
4.2A Maximum
Application: Intended for indoor use, in dry or damp locations.
The recommended ambient environment temperature is −4ºF to 122ºF, and relative humidity up to 95%. Suggested for use with
refrigerated food or beverage cabinets; bar and counter accent; under cabinet task lighting; toe kick accent lighting; display cases
and windows; trade show booths; architectural coves; audio/visual accents.
CONTROLLER PUSH BUTTONS:
WAC Lighting
www.waclighting.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. June, 2014
INSTALLATION INSTRUCTION
InvisiLED® Indoor Controller
LED-TC-CTR-MSD
FUNCTION OF BUTTONS:
1. Brightness Adjustment Button: Push the (up) and  (down) buttons on the
column to adjust the total brightness
of the INVISILED® tape light. There are 10 steps for the brightness level; the dimming range is from 100% to 0.
Dim to 0 to turn power off.
2. Color Changing Speed Button: Push the (faster) and (slower) buttons on the * column to adjust the color transition
speed of the INVISILED® tape light. There are 10 steps for the color transition. When the speed reaches its maximum or
minimum level, these buttons are invalid.
3. Blue Indicator light: indicates button is functioning when pushed.
4. Pause and Play Button: Pushing the button fixes the color of the INVISILED® tape light
at any point during the color transition.
5. Color Button: Push the “COLOR” button to switch between RGB light and white light.
6. Red Indicator light: When lit, the 24V DC power supply is plugged in.
CONTROLLER PUSH BUTTONS:
SAMPLE LAYOUT
A EN-2460D-C-P
PLUG IN POWER SUPPLY
B LED-TC-CTR-MSD
INDOOR CONTROLLER
WITH DMX
C LED-TO24-WS
PALETTE WIRELESS
CONTROLLER
D LED-TC24-SW60
PALETTE SIGNAL WIRE
E LED-TC-X
X CONNECTOR
F LED-TC-Y
Y CONNECTOR
G LED-TC-IC72
6 FOOT JOINER CABLE
H LED-TC-1-RGB
1 FOOT PALETTE TAPE
SECTION
I LED- TC-5-RGB
5 FOOT PALETTE TAPE
SECTION
J LED-TC-EC
END CAP
WAC Lighting
www.waclighting.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. June, 2014
INSTALLATION INSTRUCTION
InvisiLED® Indoor Controller
LED-TC-CTR-MSD
MASTER CONTROLLER
Set switch on the controller to the Master location for the controller to be used as the Master Controller. The buttons will function
to adjust the tape light. To operate under remote control, please refer to the remote control instruction sheet.
Slave Controller
Set the switch to the Slave position for the controller to have slave function only; following the Master Controller.
The buttons on the box will have no function.
DMX CONTROLLER
Set the switch to DMX to run the controller under DMX control. Each controller box needs to be set to DMX. The buttons on the
box will have no function after connecting with DMX. The DMX system will start to work.
DMX ADDRESSING
When using a DMX controller, each box needs a DMX starting address in order to respond to the correct control signal coming
from the DMX controller. To allocate a DMX starting address, combine various dip switches that represent binary values.
Find the shortest path to the DMX value for correct address assignment.
Example:
DMX Address 001 = Dip Switch 1”ON”=Binary value 1
DMX Address 009 = Dip Switches 1and 4”ON”=Binary value 9
DMX Address 087 = Dip Switches 1, 2, 3, 5, 7”ON”=Binary value 87
Math 1+2+4+16+64=87
WAC Lighting
www.waclighting.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. June, 2014