Webcam Imaging with Small Telescopes

Webcam Imaging with Small Telescopes
Erwin Matys, Karoline Mrazek
With webcams and freeware like Registax readily available, many owners of small telescopes have
been trying to image celestial objects. The Moon, the Sun, bright planets like Jupiter or Saturn and
double stars are the favourite targets. Most of the times, the enthusiastic beginning
astrophotographer is deeply disappointed. Images of lunar craters lack detail, Jupiter is a mere
bright blob showing nothing more than perhaps
one or two belts at best and Mars’ polar caps are
hardly discernible. The reason for these lowresolution results surely isn’t bad image
processing software. For example, Registax is a
highly sophisticated piece of software that
operates nearly automatically. Neither can the
optics be blamed. Most amateur telescopes in
the 4-inch class are fitted with high-quality optics
that allow diffraction-limited imaging. So why
does it seem to be so hard to obtain high-quality webcam images with small telescopes? The
answer is simple: Most casual imagers pay way too little attention to the imaging process itself.
Tune your imaging process: When it comes to astronomical imaging, a simple rule applies - what
the source lacks cannot be processed into the result. With webcam imaging, the source is the
video file you capture with your telescope/webcam setup in the field. The consequence is: There is
every reason to make sure that this webcam video file has the highest possible quality. The
following hints may give you a clue how to reach the turning point in your solar system imaging.
Wait for good seeing: There is a myth that webcams overcome bad seeing conditions. This is only
partially true. Although it is correct that even
under bad seeing conditions your video file will
include some good frames, you’d better go for a
large amount of good frames. This is only
possible when seeing conditions are excellent.
Even under good seeing conditions, an object
elevation above horizon of at least 30 degrees is
necessary to get a satisfying result. Only on some
very special nights with exceptional seeing
conditions this value may be a little lower. In any
case, always image the object at the highest
possible elevation above the horizon. If this
means to wait, then wait. Also remember, after
midnight the seeing often calms down. In most
nights the second half of the night is the best period for imaging planets or lunar detail. If you have
to capture your video in the evening or morning (e.g. when imaging Venus or Mercury), shoot
within one hour of sunset or sunrise.
Let your telescope cool down: Small telescopes are not as much plagued by tube seeing as larger
scopes are. Nevertheless, also small scopes have to cool down to ambient temperature to perform
satisfactorily. The simple rule is, bring your instrument outdoors in time, especially if you are using
© Erwin Matys, Karoline Mrazek
a Newtonian design. Even for telescopes in the 4-inch class a cool-down time of at least one hour
is strongly recommended.
Focus carefully: One of the most critical factors for capturing high-resolution webcam videos is to
image at the correct focus. The authors have seen amateurs focusing by
simply sliding the webcam in and out of the focuser drawtube. This is
surely not the way to focus for a high-resolution planetary image. Some
simple math shows that at f/25 a webcam chip with a pixel size of
around 5µm must be placed within 0.1mm of the telescope’s focal
plane. Consequently, a lot of effort must be taken to find the best focus.
We recommend taking several minutes for this task, focusing, defocusing and focusing again, until the best possible image is steadily
visible on the computer’s monitor. Very small bright features like a
Jovian moon or a lunar crater peak can be useful for this important step. Remember that your
stacked result strongly depends on how crisp the individual frames of your webcam video are.
Use an IR/UV cut filter: Your webcam is sensitive to wavelengths in the ultraviolet and infrared
part of the spectrum. These wavelengths tend to blur all channels (red, green and blue) of your
webcam video. Therefore, an IR/UV cut filter should be used to block these wavelengths. IR/UV
cut filters are available from most telescope dealers. If you bought your webcam from a telescope
dealer, chances are that your webcam already came with a 1.25” IR/UV cut filter.
Collimate your scope: Even short-focus instruments like an f/4 Newtonian are capable of imaging
the planets, however, they are quite sensitive to collimation errors. Many amateurs with shortfocus instruments believe that their telescopes are not usable for planetary work. In most cases,
the optics are quite fine, they are just out of collimation. The best way to find out whether your
scope is in collimation is the star test.
Refer to your instrument’s manual or
to web resources to find out how to
star test and how to collimate your
short-focus instrument.
Adjust your focal length: Optimum
angular resolution can only be
resolvable detail covers two by two
of the webcam’s pixels or more. With
most small telescopes and webcams,
this is the case when the focal ratio is
around f/20. To estimate the needed
focal length, simply multiply your
telescope’s aperture with 20.
Consider eyepiece projection: Most
webcam imagers use Barlow lenses
to extend the focal length to the desired value. With short-focus instruments a 2x or 3x Barlow
may not be enough. In this case, eyepiece projection is a valid alternative. Especially if you already
own a high-quality planetary eyepiece this method boosts your effective focal length at no extra
© Erwin Matys, Karoline Mrazek
cost. You only have to find a way to mount your webcam several centimetres behind the eyepiece.
We wouldn’t recommend duct tape, but for testing your configuration this will work.
Use a high-quality Barlow: Even if your telescope is no short-focus instrument, the standard focal
length will not be enough to capture the smallest possible details. In this case, a high-quality
Barlow lens will work best. Low-cost Barlow
lenses suffer from chromatic aberration, which
becomes visible as coloured fringes around
bright objects. They also introduce ghost images
and reduce contrast noticeably. For webcam
imaging, always use the best Barlow available.
Try special filters: As mentioned above, colour
images gain contrast when exposed through an
IR/UV cut filter. For special applications, other
filters are worth a try. Our Sun, for example, is
best imaged with a combination of a full
aperture solar filter and a so-called solar
continuum filter. Both are sold by Baader
atmosphere, a violet filter can be helpful. And the other planets respond well to an infrared pass
filter, if the luminosity channel is to be recorded separately from the RGB channels.
Use flatfields: Especially when imaging solar or lunar detail, proper image calibration with a
flatfield is necessary. Otherwise the inevitable dust specks on the webcam chip will show up
prominently. With webcams it is quite easy to produce flatfields. Simply point your scope at
something uniformly bright, like the early evening sky. Set your webcam to auto-exposure and
capture a video of several hundred frames. Use this video file in programs such as Registax to
generate a flatfield, which you later apply in your stacking process.
Switch to polar mode: Today, computer-aided telescopes with GoTo functions are quite popular,
even amongst beginners. If you own such a scope, you are
probably using it in the standard alt-azimuth mode of
operation. For webcam imaging, it is a better choice to
switch your GoTo telescope to the equatorial (or polar)
mode. In this mode, the telescope’s mount needs to use
only one axis for tracking. Therefore it will be much more
reliable in following your imaging target. Refer to your
telescope’s manual on how to operate it in polar mode.
Polar align carefully: Whether you are using a GoTo or a
conventional equatorial mount, always polar align carefully.
If the hour axis of your telescope is too far off the celestial
pole, object tracking won’t perform satisfactorily and your target will drift out quite fast of the
webcam’s small field of view. This makes focusing and recording videos an almost impossible task.
Set the correct exposure value: When trying to record a well saturated source, many beginning
webcam photographers have the tendency to overexpose their video files. Overexposure means
that there are regions in the image that have brightness values of 255. Within such regions, no
© Erwin Matys, Karoline Mrazek
object information will be recorded. When processing a planetary image with such overexposed
areas, the result always looks unnatural. To avoid overexposure, make test shots to find the
correct exposure for your object.
Collect enough frames: To obtain a good signal-to-noise ratio, a simple rule applies: The more
frames, the better. For a high-quality planetary image, one or two hundred frames won’t be
enough. Videos with one or two thousand frames have a
much better chance to contain the information you want to
record. Thin low-contrast bands on Jupiter, tiny lunar rilles
and subtle shadings on Mars are the kind of details the
Registax Wavelets will bring out if you provide a video file
with a sufficient number of frames.
Use the highest possible frame rate: When imaging a
planet, the time span for recording your video is limited by
the planet’s rotation. For example, webcam videos of Jupiter
made with a small telescope should not exceed three
minutes. If you record longer, planetary rotation will smear
the details in the resulting image. Therefore, it is necessary to use the highest possible frame rate.
This way you will be able to record the largest number of frames possible within a given time
period. 30 fps (frames per second) is a typical value that will be working fine with most computers.
The frame rate can be set manually in the video driver of your webcam.
The authors Karoline Mrazek and Erwin Matys are founding members of the astrophotography
group project nightflight. Check out their images, tests and tools at
© Erwin Matys, Karoline Mrazek
Download PDF
Similar pages