Rack Mount Instructions

Installing the Rack Mount
ET 350 Monitor (Model 350R), ET 3170 Terminal, and ET 3200 Series Computers
Intended Use
CAUTION
When properly installed using the materials provided, and
according to these instructions, the rack mount is intended
to mount the 3M DynaproTM ET 350 monitor, the ET 3170
terminal, and ET 3200 series computers for use in a
standard 19-inch EIA rack.
To reduce the risks associated with fire which, if not
avoided, may result in minor or moderate injury or cause
property damage.
!
Installation of the ET unit in a rack should be such that the
amount of air flow required for safe operation of the unit is not
compromised.
Product safety information
Equipment
Read and understand all safety information in this
document before installing and using the rack mount.
Materials supplied
The Rack Mount Kit comes with the following items:
WARNING
!
To reduce the risks associated with fire and explosion
which, if not avoided, could result in death or serious injury
and/or property damage.
!
1 rack adapter (the example illustrated below is the
adapter for the ET 3170 terminal or ET 3210
computer)
Use the materials provided so that installation of the ET unit will
not result in a hazardous condition due to uneven mechanical
loading.
WARNING
To reduce the risks associated with electrical shock or fire
which, if not avoided, may result in death or serious injury
and/or property damage:
!
Follow all product and accessory installation instructions.
WARNING
73145_a
To reduce the risks associated with electrical shock or fire
which, if not avoided, could result in death or serious injury
and/or property damage:
!
!
Reliable earthing of rack-mounted equipment should be
maintained. Particular attention should be given to supply
connections other than direct connections to the branch circuit
(e.g., use of power strips).
Consideration should be given to the connection of the ET unit to
the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
!
8 clip nuts
!
12 Phillips #10-32 x ½ inch panhead machine screws
!
12 flat washers
!
12 lock washers
!
8 slotted #10-32 x 5/8 inch countersunk machine
screws
!
8 cup washers
Tools Required
!
No. 2 Phillips screwdriver
!
Large flat-blade screwdriver
3M Touch Systems Proprietary Information
1
Installing the Rack Mount
Mounting steps
4.
On each of the twelve #10-32 panhead machine
screws, first put on a lock washer and then put on a
flat washer.
5.
Using a No. 2. Phillips screwdriver, attach each screw
(with lock washer and flat washer) through the holes
in the rack adapter and into the back of the bezel of
the ET unit.
6.
Tighten each screw to a torque of 12 inch-pounds.
7.
If your unit requires security screws (available as an
option from 3M Touch Systems), insert them.
8.
Pick up the rack adapter with the ET unit attached and
fit it to the rack. Position it to match the locations of
the clips installed earlier.
9.
Fasten the adapter/ET unit to the clip nuts in the rack
with the eight slotted #10-32 x 5/8-inch countersunk
machine screws with a cup washer on each screw.
Important
If installed in a closed or multi-unit rack assembly, the operating
ambient temperature of the rack environment may be greater
than room ambient temperature. Therefore, consideration should
be given to installing the equipment in an environment
compatible with the manufacturer’s maximum rated ambient
temperature.
To install the rack adapter in the 19-inch rack, follow
these steps:
1.
To determine where to attach the clip nuts to the rack,
hold the rack adapter in the rack where you want to
mount the ET unit. Fasten the clip nuts on the rack so
that they match the locations of the slots in the sides
of the rack adapter.
The clip nuts will “clip” to the rack. Screws and
washers are not required.
2.
Place the ET unit face down on a padded bench or
other protected surface.
3.
Fit the rack adapter over the back of the ET unit,
against the back of the bezel.
10. Connect data and power cables.
3M Touch Systems Proprietary Information
2
Copyright
This manual is © 3M 2002. All rights reserved.
Reproduction of the contents of this copyrighted manual in
whole or in part, by any means, electronic or mechanical,
for any purpose, without written permission of 3M Touch
Systems, a subsidiary of 3M, is prohibited.
Notice
Given the variety of factors that can affect the use and
performance of a 3M Touch Systems Product (the
“Product”), including that solid state equipment has
operation characteristics different from electromechanical
equipment, some of which factors are uniquely within
User’s knowledge and control, it is essential that User
evaluate the 3M Touch Systems Product and software to
determine whether it is suitable for User’s particular
purpose and suitable for User’s method of application. 3M
Touch Systems’ statements, engineering/technical
information, and recommendations are provided for User’s
convenience, but their accuracy or completeness is not
warranted. 3M Touch Systems products and software are
not specifically designed for use in medical devices as
defined by United States federal law. 3M Touch Systems
products and software should not be used in such
applications without 3M Touch Systems’ express written
consent. User should contact its sales representative if
User’s opportunity involves a medical device application.
Important notice to purchaser
Specifications are subject to change without notice. These
3M Touch Systems’ Products and software are warranted
to meet their published specifications from the date of
shipment and for the period stated in the specification.
3M Touch Systems
3M Optical Systems Division
800 Carleton Court
Annacis Island
New Westminster, BC
Canada V3M 6L3
www.3Mtouch.com
3M Touch Systems makes no additional warranties,
express or implied, including but not limited to any
implied warranties of merchantability or fitness for a
particular purpose.
User is responsible for determining whether the 3M Touch
Systems Products and software are fit for User’s particular
purpose and suitable for its method of production,
including intellectual property liability for User's
application. If the Product, software or software media is
proven not to have met 3M Touch Systems’ warranty, then
3M Touch Systems’ sole obligation and User’s and
Purchaser’s exclusive remedy, will be, at 3M Touch
Systems’ option, to repair or replace that Product quantity
or software media or to refund its purchase price. 3M
Touch Systems has no obligation under 3M Touch
Systems’ warranty for any Product, software or software
media that has been modified or damaged through misuse,
accident, neglect, or subsequent manufacturing operations
or assemblies by anyone other than 3M Touch Systems.
3M Touch Systems shall not be liable in any action
against it in any way related to the Products or software
for any loss or damages, whether non-specified direct,
indirect, special, incidental or consequential (including
downtime, loss of profits or goodwill) regardless of the
legal theory asserted.
Edition
Second edition: October 2002
Document Number: 19916 (Rev. 1.0)
(Supersedes 80-0453)
Trademark
3M Dynapro is a trademark of 3M.
For more information on 3M touch products, visit
3Mtouch.com or call toll-free 1-800-667-0374.
Worldwide Manufacturing Plants
Methuen, Massachusetts
Milwaukee, Wisconsin
Vancouver, BC, Canada
© 3M 2002
19916 (Rev. 1.0)