X-Ring Managed Industrial Switch

6 10/100/1000T + 2 10/100/1000T/
100/1000 SFP Combo
w/ X-Ring Managed Industrial Switch
SISGM1040-262D-LR
User Manual
33577 Rev B
November 2013
577
Transition Networks
SISGM1040-262D-LR User Guide
FCC Warning
This Equipment has been tested and found to comply with the limits for a Class-A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Record of Revisions
Rev. A. - Aug. 2009 - Initial document release.
Rev. B - Nov. 26, 2013 - Login security enhancements added at v 1.02_k5.03.12.
33577 Rev. B
www.transition.com
Page 2 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Content
Introduction ..................................................................................................................... 5
Benefits .......................................................................................................................... 5
Package Contents ......................................................................................................... 7
Hardware Description ..................................................................................................... 8
Physical Dimensions ..................................................................................................... 8
Front Panel .................................................................................................................... 8
Top View ........................................................................................................................ 9
LED Indicators ............................................................................................................... 9
Ports ............................................................................................................................ 11
Cabling ........................................................................................................................ 14
Wiring the Power Inputs .............................................................................................. 16
Wiring the Fault Alarm Contacts .................................................................................. 17
Installation ..................................................................................................................... 18
DIN-Rail Mounting ....................................................................................................... 18
Wall Mounting .............................................................................................................. 20
Installation Steps ......................................................................................................... 21
Network Application ..................................................................................................... 22
X-Ring Application ....................................................................................................... 22
Coupling Ring Application ........................................................................................... 23
Dual Homing Application ............................................................................................. 24
Console Management ................................................................................................... 25
RS-232 Console .......................................................................................................... 25
Login in the Console Interface ..................................................................................... 26
Command Set List ....................................................................................................... 28
Commands Level ................................................................................................... 28
Commands Set List ................................................................................................ 28
System Command Set ........................................................................................... 29
Port Command Set ................................................................................................. 31
Trunk Command Set .............................................................................................. 33
VLAN Command Set .............................................................................................. 34
Spanning Tree Command Set ................................................................................ 36
QOS Command Set ............................................................................................... 38
IGMP Command Set .............................................................................................. 39
MAC / Filter Table Command Set .......................................................................... 40
SNMP Command Set ............................................................................................. 41
Port Mirroring Command Set.................................................................................. 43
802.1x Command Set ............................................................................................. 44
TFTP Command Set .............................................................................................. 46
SystemLog, SMTP and Event Command Set ........................................................ 46
SNTP Command Set .............................................................................................. 48
X-ring Command Set .............................................................................................. 49
Web-Based Management ............................................................................................. 50
About Web-based Management.................................................................................. 50
Preparing for Web Management ................................................................................. 50
System Login ............................................................................................................... 51
Main Page ................................................................................................................... 52
System Information...................................................................................................... 53
IP Configuration ........................................................................................................... 54
DHCP Server – System configuration ......................................................................... 55
DHCP Server – Client Entries ..................................................................................... 56
DHCP Server - Port and IP Binding ............................................................................ 57
TFTP - Update Firmware ............................................................................................. 58
TFTP – Restore Configuration .................................................................................... 59
TFTP - Backup Configuration ...................................................................................... 60
System Event Log – Syslog Configuration .................................................................. 61
System Event Log - SMTP Configuration ................................................................... 62
System Event Log - Event Configuration .................................................................... 64
33577 Rev. B
www.transition.com
Page 3 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Fault Relay Alarm ........................................................................................................ 66
SNTP Configuration..................................................................................................... 67
IP Security ................................................................................................................... 70
User Authentication ..................................................................................................... 72
Port Statistics ............................................................................................................... 73
Port Control ................................................................................................................. 74
Port Trunk .................................................................................................................... 75
Aggregator setting .................................................................................................. 75
Aggregator Information ........................................................................................... 76
State Activity ........................................................................................................... 77
Port Mirroring ............................................................................................................... 78
Rate Limiting ................................................................................................................ 79
VLAN configuration...................................................................................................... 80
VLAN configuration - Port-based VLAN ................................................................. 81
802.1Q VLAN ......................................................................................................... 83
Rapid Spanning Tree .................................................................................................. 86
RSTP - System Configuration ................................................................................ 86
RSTP - Port Configuration...................................................................................... 87
SNMP Configuration .................................................................................................... 88
System Configuration ............................................................................................. 89
Trap Configuration .................................................................................................. 90
SNMPV3 Configuration .......................................................................................... 91
QoS Configuration ....................................................................................................... 94
QoS Policy and Priority Type ................................................................................. 94
Port Base Priority ................................................................................................... 96
COS Configuration ................................................................................................. 96
TOS Configuration .................................................................................................. 96
IGMP Configuration ..................................................................................................... 97
X-Ring .......................................................................................................................... 98
802.1X/Radius Configuration .................................................................................... 101
MAC Address Table ................................................................................................... 104
Factory Default .......................................................................................................... 106
Save Configuration .................................................................................................... 107
System Reboot .......................................................................................................... 107
Troubleshooting .......................................................................................................... 108
Technical Specifications ............................................................................................ 109
33577 Rev. B
www.transition.com
Page 4 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Introduction
The managed switch which can be easily managed through the Web GUI is a cost-effective
solution and meets the high reliability requirements demanded by industrial applications. Using
fiber port can extend the connection distance that increases the network elasticity and
performance. The switch also provides the X-Ring function that can prevent the network
connection failure.
Benefits

System Interface/Performance
 RJ-45 ports support auto MDI/MDI-X function
 SFP (Mini-GBIC) supports 100/1000 dual modes
 Store-and-Forward switching architecture
 Back-plane (Switching Fabric): 16Gbps
 1Mbits Packet Buffer
 8K-entry MAC address table

Power Supply
 Wide-range Redundant Power Design

VLAN

Port Based VLAN

Supports 802.1Q Tag VLAN

GVRP

Port Trunk with LACP

QoS (Quality of Service)


Supports IEEE 802.1p Class of Service

Per port provides 4 priority queues

Port Base, Tag Base and Type of Service Priority
Port Mirroring: Monitor traffic in switched networks

TX Packet only

RX Packet only

Both of TX and RX Packets
33577 Rev. B
www.transition.com
Page 5 of 112
Transition Networks









SISGM1040-262D-LR User Guide
Security

Port Security: MAC address entries/filter

IP Security: IP address security management to prevent unauthorized intruders

Login Security: IEEE 802.1X/RADIUS
IGMP

Query mode for Multi Media Application

Multicast filter supported
Case/Installation

IP-30 Protection

DIN Rail and Wall Mounting Design
Spanning Tree

Support IEEE 802.1d Spanning Tree

Support IEEE 802.1w Rapid Spanning Tree
X-ring

X-ring, Dual Homing, and Couple Ring Topology

Provide redundant backup feature and the recovery time below 20ms
Bandwidth Control

Ingress packet filter and egress rate limit

Broadcast/multicast packet filter control
System Event Log

System log server/client

SMTP e-mail alert

Relay alarm output for system events
SNMP Trap

Device cold start

Power status

Authentication failure

X-ring topology changed

Port link-up/link-down
TFTP firmware update and system configuration restoration/backup
33577 Rev. B
www.transition.com
Page 6 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Package Contents
Please refer to the package content list below to verify them against the checklist.

6 10/100/1000T + 2 10/100/1000T/ 100/1000 SFP Combo w/ X-Ring Managed Switch

Documentation Post Card

RS-232/RJ-45 cable

Pluggable Terminal Block

2 wall mount plates and 6 screws
Compare the contents of the package with the checklist above. If any item is damaged or
missing, please contact your local dealer for service.
33577 Rev. B
www.transition.com
Page 7 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Hardware Description
This section describes the Industrial switch’s dimensions, LED indicators, cabling information,
and wiring installation.
Physical Dimensions
The Managed Switch dimensions are 72mm x 152mm x 105mm (W x H x D).
Front Panel
The Managed Switch front panel is shown below.
Front Panel of the industrial switch
33577 Rev. B
www.transition.com
Page 8 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Top View
The Managed Switch top panel has one terminal block connector in which has two DC power
inputs and one relay alarm output.
Top Panel of the industrial switch
LED Indicators
The industrial switch has diagnostic LED indicators located on the front panel that provide realtime information of system and optional status. The following table provides descriptions of the
LED status and their meanings for the switch.
LED
Status
Description
Green
System power on
Off
No power input
PWR
Green
The industrial switch is the master of the X-Ring
group
R.M.
The industrial switch is not the ring master in the X-
Off
Ring group
Green
Power input 1 is active
Off
Power input 1 is inactive
Green
Power input 2 is active
Off
Power input 2 is inactive
PWR1
PWR2
33577 Rev. B
www.transition.com
Page 9 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Power input 1 or 2 is inactive or port link failure
Red
(depends on Fault Relay Alarm configuration)
Fault
Power input 1 and 2 are both active, or no power
Off
LNK/ACT
(for P7, P8 SFP)
inputs
Green
SFP port is linking
Blinking
Data is transmitting or receiving
Off
Not connected to network
upper
Green
Connected to network
Blinking
Networking is active
Off
No connected to network
Green
1000M
P1 ~ P8 (RJ-45)
lower
Off
33577 Rev. B
The port is disconnected or working at speed of
10/100M
www.transition.com
Page 10 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Ports

RJ-45 ports
The UTP/STP ports will automatically sense for Fast Ethernet (10Base-T/100Base-TX) or
Gigabit Ethernet (10Base-T/100Base-TX/1000Base-T) connection. Auto MDI/MDIX means that
the switch can connect to another switch or workstation without changing straight through or
crossover cabling. See the figures below for straight through and crossover cable schema.

10/100Base-TX Pinouts
Pin Number
Assignment
1
Tx+
2
Tx-
3
Rx+
6
Rx-
“+” and “-” signs represent the polarity of the wires that make up each
Note
wire pair.
The table below shows the 10Base-T/100Base-TX MDI and MDI-X port pinouts.
Pin Number
MDI-X Signal Name
MDI Signal Name
1
Receive Data plus (RD+)
Transmit Data plus (TD+)
2
Receive Data minus (RD-)
Transmit Data minus (TD-)
3
Transmit Data plus (TD+)
Receive Data plus (RD+)
6
Transmit Data minus (TD-)
Receive Data minus (RD-)
33577 Rev. B
www.transition.com
Page 11 of 112
Transition Networks

SISGM1040-262D-LR User Guide
10/100Base-TX Cable Schema
Straight Through Cable Schema
Crossover Cable Schema

10/100/1000Base-T Pinouts
The table below describes the gigabit Ethernet RJ-45 pinouts.
33577 Rev. B
Pin
Signal name
Description
1
BI_DA+
Bi-directional pair A+
2
BI_DA-
Bi-directional pair A-
3
BI_DB+
Bi-directional pair B+
4
BI_DC+
Bi-directional pair C+
5
BI_DC-
Bi-directional pair C-
6
BI_DB-
Bi-directional pair B-
7
BI_DD+
Bi-directional pair D+
8
BI_DD-
Bi-directional pair D-
www.transition.com
Page 12 of 112
Transition Networks

SISGM1040-262D-LR User Guide
10/100/1000Base-T Cable Schema
The following two figures illustrate the 10/100/1000Base-T cable schema.
Straight Through Cable Schema
Crossover Cable Schema
33577 Rev. B
www.transition.com
Page 13 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Cabling

Using four twisted-pair, Category 5e/above cabling for RJ-45 port connection. The cable
between the switch and the link partner (switch, hub, workstation, etc.) must be less than
100 meters (328 ft.) long.

Fiber segment using single-mode connector type must use 9/125 µm single-mode fiber
cable.

Fiber segment using multi-mode connector type must use 50 or 62.5/125 µm multi-mode
fiber cable.
To connect the transceiver and LC cable, please take the steps shown as follows:
First, insert the transceiver into the SFP slot. Notice that the triangle mark indicates the bottom
of the slot.
Transceiver to the SFP slot
Transceiver Inserted
33577 Rev. B
www.transition.com
Page 14 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Second, insert the fiber cable of LC connector into the transceiver.
LC connector to the transceiver
To remove the LC connector from the transceiver, please follow the steps shown below:
First, press the upper side of the LC connector from the transceiver and pull it out to release.
Remove LC connector
Second, push down the metal loop and pull the transceiver out by the plastic part.
Pull out from the SFP transceiver
33577 Rev. B
www.transition.com
Page 15 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Wiring the Power Inputs
Please follow the steps below to insert the power wires.
Insert the positive and negative wires into the V+ and V- contacts on the terminal block
connector.
Tighten the wire-clamp screws to prevent the wires from loosing.
33577 Rev. B
www.transition.com
Page 16 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Wiring the Fault Alarm Contacts
The fault alarm contacts are in the middle of the terminal block connector as the picture shown
below. Wire the contacts with warning devices like LEDs or buzzers to form an external loop.
Therefore, when the Ethernet port failure (managed industrial switch only) or power failure
occurs, the relay inside the switch changes its status which may cause the connected warning
devices to act for warning purposes.
Insert the wires into the fault alarm contacts.
Note
The wire gauge for the terminal block should be in the range
between 12~ 24 AWG.
33577 Rev. B
www.transition.com
Page 17 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Installation
DIN-Rail Mounting
Assembling the DIN-Rail Clip
The DIN-rail clip is screwed on the industrial switch when out of factory. If not, please
refer to the following steps to secure the DIN-rail clip on the switch.
1. Use the included screws to secure the DIN-rail clip on the industrial switch.
2. To remove the DIN-rail clip, reverse step 1.
DIN-Rail Clip
Rear Side of the Switch
33577 Rev. B
www.transition.com
Page 18 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Hanging the Industrial Switch
Follow the steps below to hang the industrial switch on the DIN rail.
1. Position the rear side of the switch directly in front of the DIN rail. Make sure the top of the
clip hooks over the top of the DIN rail.
2. Push the unit downward.
3. Check the DIN-Rail clip is tightly fixed on the DIN rail.
4. To remove the industrial switch from the track, reverse the steps above.
33577 Rev. B
www.transition.com
Page 19 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Wall Mounting
To hang the Ethernet switch on the wall, please follow the steps below.
1. Remove the DIN-rail clip.
2. Prepare the two wall-mount plates and six screws included.
3. Align the screw holes bewteen the wall-mount plates and the unit as the figure illustrated.
4. Secure the plates to the unit with the accompanying screws.
33577 Rev. B
www.transition.com
Page 20 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Installation Steps
1. Unpack the Industrial switch
2. Check if the DIN-rail clip is screwed on the Industrial switch or not. If the DIN-rail clip is not
screwed on the Industrial switch, please refer to the DIN-Rail Mounting section for DIN-rail
installation. If users want to wall-mount the Industrial switch, then please refer to Wall-Mount
Plate Mounting section for wall-mount plate installation.
3. To hang the Industrial switch on the DIN-rail or wall, please refer to the Mounting
Installation section.
4. Power on the Industrial switch. Please refer to the Wiring the Power Inputs section for
knowing the information about how to wire the power. The power LED on the Industrial
switch will light up. Please refer to the LED Indicators section for indication of LED lights.
5. Prepare the twisted-pair, straight through Category 5 cable for Ethernet connection.
6. Insert one side of RJ-45 cable (category 5) into the Industrial switch Ethernet port (RJ-45
port) and another side of RJ-45 cable (category 5) to the network device’s Ethernet port (RJ45 port), ex: Switch PC or Server. The UTP port (RJ-45) LED on the Industrial switch will
light up when the cable is connected with the network device. Please refer to the LED
Indicators section for LED light indication.
7. When all connections are set and LED lights all show in normal, the installation is complete.
33577 Rev. B
www.transition.com
Page 21 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Network Application
This chapter provides sample applications to give a better idea of possible switch applications.
X-Ring Application
The industrial switch supports the X-Ring protocol that can help the network system recover from
network connection failure within 10ms or less and make the network system more reliable. The
X-Ring algorithm is similar to Spanning Tree Protocol (STP) and Rapid STP (RSTP) algorithm
but its recovery time is less than STP/RSTP. The figure below is a sample of X-Ring application.
33577 Rev. B
www.transition.com
Page 22 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Coupling Ring Application
As the illustration shown below, users can use the X-Ring groups to form a coupling ring for
redundant backup. It can ensure the transmissions between X-Ring groups not to fail. The
following figure is a sample of coupling ring application.
33577 Rev. B
www.transition.com
Page 23 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Dual Homing Application
The Dual Homing function is to prevent the connection loss between the particular X-Ring group
and the upper level/core switch. Assign one port, and only one, to be the Dual Homing port that
is the backup port in each single X-Ring group. The Dual Homing function only works when the
X-Ring function is active.
Note
In Dual Homing application architecture, the upper level switches need to
enable their Rapid Spanning Tree protocol.
33577 Rev. B
www.transition.com
Page 24 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Console Management
RS-232 Console
One end of the supplied console cable is RS-232 connector and the other end is RJ-45
connector. Attach the RS-232 end to a PC/terminal and the RJ-45 end to the console port of the
Ethernet Switch. The connected terminal or PC must support the terminal emulation program.
Console cable
Pin Assignments
D-sub 9
Connector
33577 Rev. B
RJ-45 Connector
NC
1
Orange/White
2
2
Orange
3
3
Green/White
NC
4
Blue
5
5
Blue/White
NC
6
Green
NC
7
Brown/White
NC
8
Brown
www.transition.com
Page 25 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Login in the Console Interface
When the connection between Switch and PC is ready, turn on the PC and run a terminal
emulation program or Hyper Terminal and configure its communication parameters to match
the following default characteristics of the console port:
Baud Rate: 9600 bps
Data Bits: 8
Parity: none
Stop Bit: 1
Flow control: None
Communication Parameter Settings
After finishing the parameter settings, click ‘OK’. When a blank window shows up, press Enter to
bring out the login prompt. Key in the ‘root’ (default value) for both User name and Password
(press Enter to switch between); and then press Enter to have the console management appear.
Please see the figure as follows.
33577 Rev. B
www.transition.com
Page 26 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Console login interface
The system supports a command line interface management–CLI. After you have logged in the
system, you will see a command prompt. To enter CLI management interface, enter “enable”
command.
CLI command interface
33577 Rev. B
www.transition.com
Page 27 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Command Set List
Commands Level
The following table lists the CLI command levels and description.
Modes
Access
Method
Prompt
Exit
Method
About This Model
The user commands
available at the user level
are a subset of those
available at the privileged
level.
Use this mode to
• Perform basic tests.
• Displays system
information.
The privileged commands
are the advanced mode.
Use this mode to
• Display advance function
status
• Save configurations
User EXEC
Begin a session
with your switch.
switch>
Enter logout
or quit.
Privileged
EXEC
Enter the enable
command while
in user EXEC
mode.
switch#
Enter disable
to exit.
switch (config)#
To exit to
Privileged
EXEC mode,
enter exit or
end
Use this mode to configure
parameters to be applied
to your switch.
switch (vlan)#
To return to
User EXEC
mode, enter
exit.
Use this mode to configure
VLAN-specific parameters.
switch (configif)#
To return to
the previous
mode, enter
exit or end.
Use this mode to configure
parameters for the switch
and Ethernet ports.
Global
Configuration
VLAN database
Interface
configuration
Enter the
configure
command while
in privileged
EXEC mode.
Enter the vlan
database
command while
in privileged
EXEC mode.
Enter the
interface
command with a
specific interface
while in global
configuration
mode
Commands Set List
User EXEC
E
Privileged EXEC
P
Global configuration
G
VLAN database
V
Interface configuration
I
33577 Rev. B
www.transition.com
Page 28 of 112
Transition Networks
SISGM1040-262D-LR User Guide
System Command Set
Commands
Level
Description
Example
show config
E
Show switch configuration switch>show config
show terminal
P
Show console information
switch#show terminal
Save user configuration
write memory
P
into permanent memory
switch#write memory
(flash rom)
system name
[System Name]
system location
[System Location]
system description
[System Description]
system contact
[System Contact]
show system-info
G
G
G
G
E
ip address
[Ip-address] [Subnet-mask]
G
[Gateway]
ip dhcp
show ip
no ip dhcp
G
P
G
reload
G
default
G
admin username
[Username]
admin password
Set switch system location
string
Set switch system
description string
Set switch system contact
window string
Show system information
switch(config)#system name xxx
switch(config)#system location xxx
switch(config)#system description xxx
switch(config)#system contact xxx
switch>show system-info
Configure the IP address of switch(config)#ip address 192.168.16.1
switch
255.255.255.0 192.168.16.254
Enable DHCP client
switch(config)#ip dhcp
function of switch
Show IP info of switch
switch#show ip
Disable DHCP client
switch(config)#no ip dhcp
function of switch
Halt and perform a cold
restart
Restore to default
switch(config)#reload
switch(config)#default
Changes a login
G
username.
switch(config)#admin username xxxxxx
(maximum 10 words)
G
[Password]
show admin
Configure system name
Specifies a password
(maximum 10 words)
P
Show administrator
information
switch(config)#admin password xxxxxx
switch#show admin
dhcpserver enable
G
Enable DHCP Server
switch(config)#dhcpserver enable
Dhcpserver disable
G
Disable DHCP Server
switch(config)#no dhcpserver
dhcpserver lowip
G
Configure low IP address
switch(config)#dhcpserver lowip
33577 Rev. B
www.transition.com
Page 29 of 112
Transition Networks
SISGM1040-262D-LR User Guide
[Low IP]
dhcpserver highip
[High IP]
dhcpserver subnetmask
[Subnet mask]
dhcpserver gateway
[Gateway]
dhcpserver dnsip
[DNS IP]
dhcpserver leasetime
[Hours]
dhcpserver ipbinding
[IP address]
show dhcpserver
configuration
for IP pool
G
G
G
G
G
for IP pool
P
P
show dhcpserver ip-binding
P
no dhcpserver
G
security enable
G
security http
G
security telnet
G
192.168.1.200
Configure subnet mask for switch(config)#dhcpserver subnetmask
DHCP clients
255.255.255.0
Configure gateway for
switch(config)#dhcpserver gateway
DHCP clients
192.168.1.254
Configure DNS IP for
switch(config)#dhcpserver dnsip
DHCP clients
192.168.1.1
Configure lease time (in
hour)
clients by port
show dhcpserver clients
security ip
Configure high IP address switch(config)#dhcpserver highip
Set static IP for DHCP
I
192.168.1.100
Show configuration of
DHCP server
Show client entries of
DHCP server
Show IP-Binding info of
DHCP server
Disable DHCP server
function
switch(config)#dhcpserver leasetime 1
switch(config)#interface fastEthernet 2
switch(config)#dhcpserver ipbinding
192.168.1.1
switch#show dhcpserver configuration
switch#show dhcpserver clients
switch#show dhcpserver ip-binding
switch(config)#no dhcpserver
Enable IP security function switch(config)#security enable
Enable IP security of HTTP
server
Enable IP security of telnet
server
switch(config)#security http
switch(config)#security telnet
G
Set the IP security list
show security
P
Show the info of IP security switch#show security
no security
G
Disable IP security function switch(config)#no security
no security http
G
no security telnet
G
[Index(1..10)] [IP Address]
33577 Rev. B
Disable IP security of
HTTP server
Disable IP security of telnet
server
www.transition.com
switch(config)#security ip 1 192.168.1.55
switch(config)#no security http
switch(config)#no security telnet
Page 30 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Port Command Set
Commands
interface fastEthernet
Level
G
[Portid]
Choose the port for
modification.
Example
switch(config)#interface fastEthernet 2
Use the duplex
duplex
[full | half]
Description
I
configuration command to switch(config)#interface fastEthernet 2
specify the duplex mode of switch(config-if)#duplex full
operation for Fast Ethernet.
Use the speed
configuration command to
speed
[10|100|1000|auto]
specify the speed mode of
I
operation for Fast
Ethernet., the speed can’t
switch(config)#interface fastEthernet 2
switch(config-if)#speed 100
be set to 1000 if the port is
not a giga port.
no flowcontrol
I
security enable
I
no security
I
Disable flow control of
interface
Enable security of interface
I
interface
switch(config-if)#no security
frame type to ‘accept all
Set interface ingress limit
multicast-flooded-unicast
I
frame type to ‘accept
broadcast, multicast, and
flooded unicast frame’
Set interface ingress limit
bandwidth type broadcastmulticast
I
frame type to ‘accept
broadcast and multicast
frame’
bandwidth type broadcastonly
bandwidth in
[Value]
33577 Rev. B
I
switch(config)#interface fastEthernet 2
switch(config-if)#bandwidth type all
switch(config)#interface fastEthernet 2
switch(config-if)#bandwidth type
broadcast-multicast-flooded-unicast
switch(config)#interface fastEthernet 2
switch(config-if)#bandwidth type
broadcast-multicast
Set interface ingress limit
switch(config)#interface fastEthernet 2
frame type to ‘only accept
switch(config-if)#bandwidth type
broadcast frame’
broadcast-only
Set interface input
I
switch(config-if)#security enable
switch(config)#interface fastEthernet 2
frame’
bandwidth type broadcast-
switch(config)#interface fastEthernet 2
Disable security of
Set interface ingress limit
bandwidth type all
switch(config-if)#no flowcontrol
bandwidth. Rate Range is
from 100 kbps to 102400
www.transition.com
switch(config)#interface fastEthernet 2
switch(config-if)#bandwidth in 100
Page 31 of 112
Transition Networks
SISGM1040-262D-LR User Guide
kbps or to 256000 kbps for
giga ports,
and zero means no limit.
Set interface output
bandwidth. Rate Range is
bandwidth out
from 100 kbps to 102400
switch(config)#interface fastEthernet 2
[Value]
kbps or to 256000 kbps for switch(config-if)#bandwidth out 100
giga ports,
and zero means no limit.
show bandwidth
I
Show interfaces bandwidth switch(config)#interface fastEthernet 2
switch(config-if)#show bandwidth
control
Use the state interface
configuration command to
state
[Enable | Disable]
specify the state mode of
I
switch(config)#interface fastEthernet 2
operation for Ethernet
switch(config-if)#state Disable
ports. Use the disable form
of this command to disable
the port.
show interface configuration
I
show interface status
I
show interface accounting
I
no accounting
I
33577 Rev. B
switch(config)#interface fastEthernet 2
show interface
switch(config-if)#show interface
configuration status
configuration
show interface actual
status
switch(config-if)#show interface status
show interface statistic
counter
switch(config)#interface fastEthernet 2
switch(config)#interface fastEthernet 2
switch(config-if)#show interface accounting
Clear interface accounting switch(config)#interface fastEthernet 2
information
www.transition.com
switch(config-if)#no accounting
Page 32 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Trunk Command Set
Commands
aggregator priority
[1~65535]
Level
G
Description
Set port group system
priority
Example
switch(config)#aggregator priority 22
aggregator activityport
[Group ID]
G
Set activity port
switch(config)#aggregator activityport 2
[Port Numbers]
Assign a trunk group with
LACP active.
[GroupID] :1~4
[Port-list]:Member port list,
aggregator group
This parameter could be a
[GroupID] [Port-list]
port range(ex.1-4) or a port
lacp
G
list separate by a
workp
comma(ex.2, 3, 6)
[Workport]
[Workport]: The amount of
switch(config)#aggregator group 1 1-4
lacp workp 2
or
switch(config)#aggregator group 2 1,4,3
lacp workp 3
work ports, this value could
not be less than zero or be
large than the amount of
member ports.
Assign a static trunk group.
[GroupID] :1~4
aggregator group
[GroupID] [Port-list]
nolacp
[Port-list]:Member port list,
G
This parameter could be a
port range(ex.1-4) or a port
list separate by a
switch(config)#aggregator group 1 2-4
nolacp
or
switch(config)#aggregator group 1 3,1,2
nolacp
comma(ex.2, 3, 6)
switch#show aggregator 1
show aggregator
P
Show the information of
trunk group
or
switch#show aggregator 2
or
switch#show aggregator 3
no aggregator lacp
[GroupID]
no aggregator group
[GroupID]
33577 Rev. B
G
G
Disable the LACP function
of trunk group
Remove a trunk group
www.transition.com
switch(config)#no aggreator lacp 1
switch(config)#no aggreator group 2
Page 33 of 112
Transition Networks
SISGM1040-262D-LR User Guide
VLAN Command Set
Commands
Level
vlan database
P
Description
Enter VLAN configure
mode
Example
switch#vlan database
switch(vlan)#vlanmode portbase
or
Vlanmode
[portbase| 802.1q |
gvrp]
V
To set switch VLAN mode. switch(vlan)#vlanmode 802.1q
or
switch(vlan)#vlanmode gvrp
no vlan
V
No VLAN
Switch(vlan)#no vlan
Ported based VLAN configuration
vlan port-based grpname
switch(vlan)#vlan port-based grpname
[Group Name]
grpid
[GroupID]
test grpid 2 port 2-4
V
Add new port based VALN or
switch(vlan)#vlan port-based grpname
port
test grpid 2 port 2,3,4
[PortNumbers]
show vlan [GroupID]
or
show vlan
no vlan group
[GroupID]
V
Show VLAN information
switch(vlan)#show vlan 23
V
Delete port base group ID
switch(vlan)#no vlan group 2
IEEE 802.1Q VLAN
Change the name of VLAN
vlan 8021q name
[GroupName]
vid
[VID]
V
group, if the group didn’t
switch(vlan)#vlan 8021q name test vid
exist, this command can’t
22
be applied.
Assign a access link for
vlan 8021q port
[PortNumber]
access-link untag
[UntaggedVID]
VLAN by port, if the port
V
belong to a trunk group,
this command can’t be
switch(vlan)#vlan 8021q port 3 accesslink untag 33
applied.
vlan 8021q port
[PortNumber]
trunk-link tag
[TaggedVID List]
vlan 8021q port
[PortNumber]
hybrid-link untag
[UntaggedVID]
33577 Rev. B
V
V
Assign a trunk link for
switch(vlan)#vlan 8021q port 3 trunk-
VLAN by port, if the port
link tag 2,3,6,99
belong to a trunk group,
or
this command can’t be
switch(vlan)#vlan 8021q port 3 trunk-
applied.
link tag 3-20
Assign a hybrid link for
switch(vlan)#vlan 8021q port 3 hybrid-
VLAN by port, if the port
link untag 4 tag 3,6,8
www.transition.com
Page 34 of 112
Transition Networks
SISGM1040-262D-LR User Guide
tag
[TaggedVID List]
vlan 8021q trunk
[PortNumber]
access-link untag
[UntaggedVID]
V
belong to a trunk group,
or
this command can’t be
switch(vlan)#vlan 8021q port 3 hybrid-
applied.
link untag 5 tag 6-8
Assign a access link for
switch(vlan)#vlan 8021q trunk 3 access-
VLAN by trunk group
link untag 33
switch(vlan)#vlan 8021q trunk 3 trunk-
vlan 8021q trunk
[PortNumber]
trunk-link tag
V
Assign a trunk link for
VLAN by trunk group
[TaggedVID List]
link tag 2,3,6,99
or
switch(vlan)#vlan 8021q trunk 3 trunklink tag 3-20
vlan 8021q trunk
[PortNumber]
hybrid-link untag
[UntaggedVID]
tag
[TaggedVID List]
show vlan [GroupID]
or
show vlan
no vlan group
[GroupID]
33577 Rev. B
switch(vlan)#vlan 8021q trunk 3 hybrid-
V
Assign a hybrid link for
VLAN by trunk group
link untag 4 tag 3,6,8
or
switch(vlan)#vlan 8021q trunk 3 hybridlink untag 5 tag 6-8
V
Show VLAN information
V
Delete port base group ID
www.transition.com
switch(vlan)#show vlan 23
switch(vlan)#no vlan group 2
Page 35 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Spanning Tree Command Set
Commands
Level
spanning-tree enable
spanning-tree priority
[0~61440]
G
G
Description
Example
Enable spanning tree
switch(config)#spanning-tree enable
Configure spanning tree
switch(config)#spanning-tree priority
priority parameter
32767
Use the spanning-tree
max-age global
configuration command to
change the interval
between messages the
spanning tree receives
spanning-tree max-age
[seconds]
G
from the root switch. If a
switch does not receive a
switch(config)#spanning-tree max-age
15
bridge protocol data unit
(BPDU) message from the
root switch within this
interval, it recomputed the
Spanning Tree Protocol
(STP) topology.
Use the spanning-tree
hello-time global
spanning-tree
hello-time
[seconds]
configuration command to switch(config)#spanning-tree hello-time
G
specify the interval
3
between hello bridge
protocol data units
(BPDUs).
Use the spanning-tree
forward-time global
configuration command to
spanning-tree
forward-time
[seconds]
G
set the forwarding-time for switch(config)#spanning-tree forwardthe specified spanning-tree time 20
instances. The forwarding
time determines how long
each of the listening and
stp-path-cost
[1~200000000]
33577 Rev. B
I
learning states last before
the port begins forwarding.
Use the spanning-tree cost switch(config)#interface fastEthernet 2
interface configuration
www.transition.com
switch(config-if)#stp-path-cost 20
Page 36 of 112
Transition Networks
SISGM1040-262D-LR User Guide
command to set the path
cost for Spanning Tree
Protocol (STP)
calculations. In the event of
a loop, spanning tree
considers the path cost
when selecting
an interface to place into
the forwarding state.
Use the spanning-tree portpriority interface
stp-path-priority
[Port Priority]
configuration command to switch(config)#interface fastEthernet 2
I
configure a port priority that switch(config-if)#stp-path-priority 128
is used when two switches
tie for position as the root
switch.
stp-admin-p2p
[Auto|True|False]
stp-admin-edge
[True|False]
stp-admin-non-stp
[True|False]
show spanning-tree
no spanning-tree
33577 Rev. B
Admin P2P of STP priority switch(config)#interface fastEthernet 2
I
on this interface.
switch(config-if)#stp-admin-p2p Auto
Admin Edge of STP priority switch(config)#interface fastEthernet 2
I
on this interface.
Admin NonSTP of STP
I
priority on this interface.
E
G
switch(config-if)#stp-admin-edge True
switch(config)#interface fastEthernet 2
switch(config-if)#stp-admin-non-stp
False
Displays a summary of the switch>show spanning-tree
spanning-tree states.
Disable spanning-tree.
www.transition.com
switch(config)#no spanning-tree
Page 37 of 112
Transition Networks
SISGM1040-262D-LR User Guide
QOS Command Set
Commands
qos policy
[weighted-fair|strict]
Level
G
Description
Select QOS policy
scheduling
Example
switch(config)#qos policy weighted-fair
qos prioritytype
[port-based|cos-only|tos-
G
Set QOS priority type
switch(config)#qos prioritytype
Configure Port-based
switch(config)#qos priority portbased 1
Priority
low
G
Configure COS Priority
switch(config)#qos priority cos 0 middle
G
Configure TOS Priority
switch(config)#qos priority tos 3 high
only|cos-first|tos-first]
qos priority portbased
[Port]
[lowest|low|middle|high]
qos priority cos
[Priority][lowest|low|middle|h
igh]
qos priority tos
[Priority][lowest|low|middle|h
G
igh]
show qos
P
no qos
G
33577 Rev. B
Displays QoS configuration
info
Disable QoS function
www.transition.com
Switch#show qos
switch(config)#no qos
Page 38 of 112
Transition Networks
SISGM1040-262D-LR User Guide
IGMP Command Set
Commands
Level
igmp enable
G
Igmp-query auto
G
Igmp-query force
G
show igmp configuration
P
show igmp multi
P
no igmp
G
no igmp-query
G
33577 Rev. B
Description
Enable IGMP snooping
function
Set IGMP query to auto
mode
Set IGMP query to force
mode
Displays the details of an
IGMP configuration.
Displays the details of an
IGMP snooping entries.
Disable IGMP snooping
function
Disable IGMP query
www.transition.com
Example
switch(config)#igmp enable
switch(config)#Igmp-query auto
switch(config)#Igmp-query force
switch#show igmp configuration
switch#show igmp multi
switch(config)#no igmp
switch#no igmp-query
Page 39 of 112
Transition Networks
SISGM1040-262D-LR User Guide
MAC / Filter Table Command Set
Commands
Level
mac-address-table static
hwaddr
Configure MAC address
I
table of interface (static).
[MAC]
mac-address-table filter
hwaddr
G
[MAC]
show mac-address-table
show mac-address-table
static
show mac-address-table filter
P
P
P
no mac-address-table static
hwaddr
I
[MAC]
no mac-address-table filter
hwaddr
G
[MAC]
no mac-address-table
33577 Rev. B
Description
G
Example
switch(config)#interface fastEthernet 2
switch(config-if)#mac-address-table
static hwaddr 000012345678
Configure MAC address
switch(config)#mac-address-table filter
table(filter)
hwaddr 000012348678
Show all MAC address
table
Show static MAC address
table
Show filter MAC address
table.
switch#show mac-address-table
switch#show mac-address-table static
switch#show mac-address-table filter
Remove an entry of MAC
switch(config)#interface fastEthernet 2
address table of interface
switch(config-if)#no mac-address-table
(static)
static hwaddr 000012345678
Remove an entry of MAC
switch(config)#no mac-address-table
address table (filter)
filter hwaddr 000012348678
Remove dynamic entry of
MAC address table
www.transition.com
switch(config)#no mac-address-table
Page 40 of 112
Transition Networks
SISGM1040-262D-LR User Guide
SNMP Command Set
Commands
snmp system-name
[System Name]
snmp system-location
[System Location]
snmp system-contact
[System Contact]
snmp agent-mode
[v1v2c|v3|v1v2cv3]
Level
G
G
G
G
Description
Example
Set SNMP agent system
switch(config)#snmp system-name
name
l2switch
Set SNMP agent system
switch(config)#snmp system-location
location
lab
Set SNMP agent system
switch(config)#snmp system-contact
contact
where
Select the agent mode of
switch(config)#snmp agent-mode
SNMP
v1v2cv3
Add SNMP community
switch(config)#snmp community-strings
string.
public right rw
snmp community-strings
[Community]
right
G
[RO/RW]
switch(config)#snmp-server host
snmp-server host
192.168.1.50 community public trap-
[IP address]
Configure SNMP server
community
host information and
[Community-string]
G
community string
trap-version
[Context Name ]
(remove)
Switch(config)#
no snmp-server host
[v1|v2c]
snmpv3 context-name
version v1
192.168.1.50
G
Configure the context
switch(config)#snmpv3 context-name
name
Test
snmpv3 user
[User Name]
group
[Group Name]
Configure the userprofile
G
password
for SNMPV3 agent. Privacy
password could be empty.
switch(config)#snmpv3 user test01
group G1 password AuthPW PrivPW
[Authentication Password]
[Privacy Password]
snmpv3 access contextname [Context Name ]
group
[Group Name ]
security-level
switch(config)#snmpv3 access contextG
Configure the access table name Test group G1 security-level
of SNMPV3 agent
[NoAuthNoPriv|AuthNoPriv|A
AuthPriv
match-rule Exact views V1 V1 V1
uthPriv]
match-rule
33577 Rev. B
www.transition.com
Page 41 of 112
Transition Networks
SISGM1040-262D-LR User Guide
[Exact|Prifix]
views
[Read View Name] [Write
View Name] [Notify View
Name]
snmpv3 mibview view
[View Name]
type
[Excluded|Included]
G
Configure the mibview
switch(config)#snmpv3 mibview view V1
table of SNMPV3 agent
type Excluded sub-oid 1.3.6.1
sub-oid
[OID]
show snmp
no snmp community-strings
[Community]
no snmp-server host
[Host-address]
no snmpv3 user
[User Name]
P
G
G
G
Show SNMP configuration switch#show snmp
Remove the specified
switch(config)#no snmp community-
community.
strings public
Remove the SNMP server switch(config)#no snmp-server
host.
Remove specified user of
SNMPv3 agent.
192.168.1.50
switch(config)#no snmpv3 user Test
no snmpv3 access contextname [Context Name ]
group
[Group Name ]
security-level
switch(config)#no snmpv3 access
[NoAuthNoPriv|AuthNoPriv|A
uthPriv]
G
match-rule
Remove specified access
context-name Test group G1 security-
table of SNMPv3 agent.
level AuthPr
iv match-rule Exact views V1 V1 V1
[Exact|Prifix]
views
[Read View Name] [Write
View Name] [Notify View
Name]
no snmpv3 mibview view
[View Name]
type
[Excluded|Included]
G
Remove specified mibview switch(config)#no snmpv3 mibview view
table of SNMPV3 agent.
V1 type Excluded sub-oid 1.3.6.1
sub-oid
[OID]
33577 Rev. B
www.transition.com
Page 42 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Port Mirroring Command Set
Commands
Level
monitor rx
G
monitor tx
G
show monitor
P
monitor
[RX|TX|Both]
I
show monitor
I
no monitor
I
33577 Rev. B
Description
Set RX destination port of
monitor function
Set TX destination port of
monitor function
Show port monitor
information
Example
switch(config)#monitor rx
switch(config)#monitor tx
switch#show monitor
Configure source port of
switch(config)#interface fastEthernet 2
monitor function
switch(config-if)#monitor RX
Show port monitor
switch(config)#interface fastEthernet 2
information
switch(config-if)#show monitor
Disable source port of
switch(config)#interface fastEthernet 2
monitor function
switch(config-if)#no monitor
www.transition.com
Page 43 of 112
Transition Networks
SISGM1040-262D-LR User Guide
802.1x Command Set
Commands
Level
Description
Example
Use the 802.1x global
8021x enable
G
configuration command to
switch(config)# 8021x enable
enable 802.1x protocols.
Use the 802.1x system
8021x system radiusip
[IP address]
radius IP global
G
switch(config)# 8021x system radiusip
configuration command to 192.168.1.1
change the radius server
IP.
Use the 802.1x system
8021x system serverport
[port ID]
server port global
G
configuration command to
change the radius server
switch(config)# 8021x system serverport
1815
port
Use the 802.1x system
8021x system accountport
[port ID]
G
account port global
switch(config)# 8021x system
configuration command to accountport
1816
change the accounting port
Use the 802.1x system
8021x system sharekey
[ID]
share key global
G
switch(config)# 8021x system sharekey
configuration command to 123456
change the shared key
value.
Use the 802.1x system
8021x system nasid
[words]
G
nasid global configuration
switch(config)# 8021x system nasid
command to change the
test1
NAS ID
Use the 802.1x misc quiet
8021x misc quietperiod
[sec.]
period global configuration
G
command to specify the
quiet period value of the
switch(config)# 8021x misc quietperiod
10
switch.
Use the 802.1x misc TX
8021x misc txperiod
[sec.]
G
period global configuration switch(config)# 8021x misc txperiod 5
command to set the TX
period.
33577 Rev. B
www.transition.com
Page 44 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Use the 802.1x misc supp
8021x misc supportimeout
[sec.]
G
timeout global
switch(config)# 8021x misc
configuration command to supportimeout 20
set the supplicant timeout.
Use the 802.1x misc server
8021x misc servertimeout
[sec.]
G
timeout global
switch(config)#8021x misc
configuration command to servertimeout 20
set the server timeout.
Use the 802.1x misc max
8021x misc maxrequest
[number]
G
request global
switch(config)# 8021x misc maxrequest
configuration command to 3
set the MAX requests.
8021x misc
Use the 802.1x misc reauth
reauthperiod
[sec.]
G
period global configuration switch(config)# 8021x misc reauthperiod
command to set the reauth 3000
period.
8021x portstate
[disable | reject | accept |
authorize]
Use the 802.1x port state
I
interface configuration
switch(config)#interface fastethernet 3
command to set the state
switch(config-if)#8021x portstate accept
of the selected port.
Displays a summary of the
show 8021x
E
802.1x properties and also switch>show 8021x
the port sates.
no 8021x
33577 Rev. B
G
Disable 802.1x function
www.transition.com
switch(config)#no 8021x
Page 45 of 112
Transition Networks
SISGM1040-262D-LR User Guide
TFTP Command Set
Commands
Level
Description
Defaults Example
Save configuration to TFTP
backup flash:backup_cfg
G
and need to specify the IP of switch(config)#backup
flash:backup_cfg
TFTP server and the file
name of image.
Get configuration from TFTP
restore flash:restore_cfg
G
server and need to specify
switch(config)#restore
the IP of TFTP server and the flash:restore_cfg
file name of image.
Upgrade firmware by TFTP
upgrade flash:upgrade_fw
G
and need to specify the IP of switch(config)#upgrade
TFTP server and the file
lash:upgrade_fw
name of image.
SystemLog, SMTP and Event Command Set
Commands
Description
Example
Set System log server IP
switch(config)# systemlog ip
address.
192.168.1.100
G
Specified the log mode
switch(config)# systemlog mode both
show systemlog
E
Displays system log.
Switch>show systemlog
show systemlog
P
Show system log client &
switch#show systemlog
no systemlog
G
Disable systemlog functon switch(config)#no systemlog
smtp enable
G
Enable SMTP function
G
Configure SMTP server IP
systemlog ip
[IP address]
systemlog mode
[client|server|both]
smtp serverip
[IP address]
smtp authentication
smtp account
[account]
smtp password
[password]
smtp rcptemail
[Index] [Email address]
33577 Rev. B
Level
G
G
G
G
G
server information
Enable SMTP
authentication
Configure authentication
account
Configure authentication
password
switch(config)#smtp enable
switch(config)#smtp serverip
192.168.1.5
switch(config)#smtp authentication
switch(config)#smtp account User
switch(config)#smtp password
Configure Rcpt e-mail
switch(config)#smtp rcptemail 1
Address
Alert@test.com
www.transition.com
Page 46 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Show the information of
show smtp
P
no smtp
G
Disable SMTP function
G
Set cold start event type
event device-cold-start
[Systemlog|SMTP|Both]
event authentication-failure
[Systemlog|SMTP|Both]
G
event X-ring-topologychange
G
[Systemlog|SMTP|Both]
event systemlog
[Link-UP|Link-Down|Both]
event smtp
I
SMTP
switch#show smtp
switch(config)#no smtp
switch(config)#event device-cold-start
both
Set Authentication failure
switch(config)#event authentication-
event type
failure both
Set X-ring topology
switch(config)#event X-ring-topology-
changed event type
change both
Set port event for system
switch(config)#interface fastethernet 3
log
switch(config-if)#event systemlog both
switch(config)#interface fastethernet 3
I
Set port event for SMTP
show event
P
Show event selection
switch#show event
no event device-cold-start
G
Disable cold start event
switch(config)#no event device-cold-
type
start
Disable Authentication
switch(config)#no event authentication-
failure event typ
failure
Disable X-ring topology
switch(config)#no event X-ring-
changed event type
topology-change
Disable port event for
switch(config)#interface fastethernet 3
system log
switch(config-if)#no event systemlog
Disable port event for
switch(config)#interface fastethernet 3
SMTP
switch(config-if)#no event smtp
Show system log client &
switch#show systemlog
[Link-UP|Link-Down|Both]
no event authenticationfailure
no event X-ring-topologychange
G
G
no event systemlog
I
no event smtp
I
show systemlog
P
33577 Rev. B
switch(config-if)#event smtp both
server information
www.transition.com
Page 47 of 112
Transition Networks
SISGM1040-262D-LR User Guide
SNTP Command Set
Commands
sntp enable
Level
G
Description
Example
Enable SNTP function
switch(config)#sntp enable
Enable daylight saving
sntp daylight
G
time, if SNTP function is
inactive, this command
switch(config)#sntp daylight
can’t be applied.
Set period of daylight
saving time, if SNTP
sntp daylight-period
[Start time] [End time]
G
function is inactive, this
switch(config)# sntp daylight-period
command can’t be applied. 20060101-01:01 20060202-01-01
Parameter format:
[yyyymmdd-hh:mm]
Set offset of daylight
sntp daylight-offset
[Minute]
G
saving time, if SNTP
function is inactive, this
switch(config)#sntp daylight-offset 3
command can’t be applied.
Set SNTP server IP, if
sntp ip
[IP]
G
SNTP function is inactive,
this command can’t be
switch(config)#sntp ip 192.169.1.1
applied.
Set timezone index, use
sntp timezone
[Timezone]
‘show sntp timzezone’
G
command to get more
switch(config)#sntp timezone 22
information of index
number
show sntp
P
show sntp timezone
P
no sntp
G
no sntp daylight
G
33577 Rev. B
Show SNTP information
Show index number of time
zone list
Disable SNTP function
Disable daylight saving
time
www.transition.com
switch#show sntp
switch#show sntp timezone
switch(config)#no sntp
switch(config)#no sntp daylight
Page 48 of 112
Transition Networks
SISGM1040-262D-LR User Guide
X-ring Command Set
Commands
Level
Description
Example
ring enable
G
Enable X-ring
switch(config)#ring enable
ring master
G
Enable ring master
switch(config)#ring master
ring couplering
G
Enable couple ring
switch(config)#ring couplering
ring dualhoming
G
Enable dual homing
switch(config)#ring dualhoming
ring ringport
[1st Ring Port] [2nd Ring
G
Port]
ring couplingport
[Coupling Port]
ring controlport
[Control Port]
ring homingport
[Dual Homing Port]
Configure 1st/2nd Ring
Port
switch(config)#ring ringport 7 8
G
Configure Coupling Port
switch(config)#ring couplingport 1
G
Configure Control Port
switch(config)#ring controlport 2
G
Configure Dual Homing
Port
Show the information of X -
switch(config)#ring homingport 3
show ring
P
no ring
G
Disable X-ring
switch(config)#no ring
no ring master
G
Disable ring master
switch(config)# no ring master
no ring couplering
G
Disable couple ring
switch(config)# no ring couplering
no ring dualhoming
G
Disable dual homing
switch(config)# no ring dualhoming
33577 Rev. B
Ring
www.transition.com
switch#show ring
Page 49 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Web-Based Management
This section introduces the configuration and functions of the Web-Based management.
About Web-based Management
The switch has an embedded HTML “website” residing in flash memory, which offers advanced
management features and lets you manage the switch from anywhere on the network with a
standard browser such as Microsoft Internet Explorer.
The Web-Based Management supports Internet Explorer 6.0 or later version. And, it is applied
for Java Applets for reducing network bandwidth consumption, enhance access speed and
present an easy viewing screen.
Preparing for Web Management
Before using web management, install the industrial switch on the network and make sure that
any one of the PCs on the network can connect with the industrial switch through the web
browser. The switch default values are:

IP Address: 192.168.16.1

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.16.254

User Name: root

Password: root
33577 Rev. B
www.transition.com
Page 50 of 112
Transition Networks
SISGM1040-262D-LR User Guide
System Login
1.
Launch the Internet Explorer browser on the PC.
2.
Key in “http:// “+” the IP address of the switch”, and then Press “Enter”.
3.
The login screen will appear right after
4.
Key in the user name and password. The default user name and password are the same as
“root”
5.
Press “Enter” or ”OK”, and then the home screen of the Web-based management appears
as below:
Login screen
33577 Rev. B
www.transition.com
Page 51 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Main Page
In the main page, you can find the tree menu structure of the Ethernet switch in the left side.
Click the “+” symbol to unroll the hiding hyperlink, and click any one of the hyperlinks to open its
function page.
Main interface
33577 Rev. B
www.transition.com
Page 52 of 112
Transition Networks
SISGM1040-262D-LR User Guide
System Information
Here you can assign the system name, location and view the system information.

System Name: Assign the name of the switch. The maximum length is 64 bytes.

System Description: Displays the description of the switch. This is a read only field.

System Location: Add descriptions for the switch’s physical location. The maximum length
is 64 bytes.

System Contact: Enter the name of contact person or organization.

Firmware Version: Displays the switch’s firmware version.

Kernel Version: Displays the kernel software version.

MAC Address: Displays the unique MAC address assigned by manufacturer (default).
System information interface
33577 Rev. B
www.transition.com
Page 53 of 112
Transition Networks
SISGM1040-262D-LR User Guide
IP Configuration
Users can configure the IP Settings and DHCP client function.

DHCP Client: Enable or disable the DHCP Client function. When DHCP Client function is
enabled, the industrial switch will be assigned an IP address from the network DHCP
Server. The default IP address will be replaced with an IP address which is assigned by the
DHCP Server. After users click Apply, a pop-up dialog shows up to inform users that when
the DHCP Client is enabled, the current IP will lose and users should find the new IP on the
DHCP Server.

IP Address: When the DHCP Client is disabled, you can assign the IP address in this field.
If the DHCP Client function is enabled, users needn’t assign the IP address manually.
Instead, the network DHCP Server will assign the IP address for the industrial switch and
display it in this field. The default IP is 192.168.16.1.

Subnet Mask: Assign the subnet mask of the IP address. If DHCP client function is
enabled, and then user needn’t assign the subnet mask manually.

Gateway: Assign the network gateway for the industrial switch. The default gateway is
192.168.16.254.

DNS1: Assign the primary DNS IP address.

DNS2: Assign the secondary DNS IP address.

And then, click
Apply .
IP configuration interface
33577 Rev. B
www.transition.com
Page 54 of 112
Transition Networks
SISGM1040-262D-LR User Guide
DHCP Server – System configuration
The system provides the DHCP Server function. With the DHCP Server function enabled,
the switch system can be a DHCP server.

DHCP Server: Enable or Disable the DHCP Server function. When enabled, the
switch will be the DHCP server on your local network.

Low IP Address: The beginning of the dynamic IP assigning range. For example:
when the dynamic IP assigning range is designated as 192.168.1.100 ~
192.168.1.200. Then 192.168.1.100 is the Low IP address.

High IP Address: The end of the dynamic IP assigning range. For example,
dynamic IP assigning range is designated as 192.168.1.100 ~ 192.168.1.200.
Therefore, 192.168.1.200 is the High IP address.

Subnet Mask: The subnet mask for the dynamic IP assigning range.

Gateway: The gateway in your network.

DNS: Domain Name Server IP Address in your network.

Lease Time (sec): It is the time period after which the system will reset the dynamic
IP assignment to ensure that the dynamic IP won’t have been occupied for a long
time; otherwise the server won’t know that the dynamic IP is idle.

And then, click Apply .
DHCP Server Configuration interface
33577 Rev. B
www.transition.com
Page 55 of 112
Transition Networks
SISGM1040-262D-LR User Guide
DHCP Server – Client Entries
When the DHCP Server function is active, the system will collect the DHCP client
information displaying in this field.
DHCP Client Entries interface
33577 Rev. B
www.transition.com
Page 56 of 112
Transition Networks
SISGM1040-262D-LR User Guide
DHCP Server - Port and IP Binding
You can assign the specific IP address in the range of dynamic IP assigning to each port.
When the device is connected to the particular port and asks for a dynamic IP, the
system will assign the IP address configured here to the connected device.
Port and IP Bindings interface
33577 Rev. B
www.transition.com
Page 57 of 112
Transition Networks
SISGM1040-262D-LR User Guide
TFTP - Update Firmware
It provides the function allowing users to update the switch firmware. Before updating,
make sure you have your TFTP server ready and the firmware image is located on the
TFTP server.
1.
TFTP Server IP Address: Fill in your TFTP server IP.
2.
Firmware File Name: the name of firmware image.
3.
Click Apply .
Update Firmware interface
33577 Rev. B
www.transition.com
Page 58 of 112
Transition Networks
SISGM1040-262D-LR User Guide
TFTP – Restore Configuration
You can restore the contents of the flash ROM from the TFTP server. Make sure you
have put the image file on the TFTP server so the switch can download back the image
file.
1.
TFTP Server IP Address: Fill in the TFTP server IP.
2.
Restore File Name: Fill in the correct file name to be restored.
3.
Click Apply .
Restore Configuration interface
33577 Rev. B
www.transition.com
Page 59 of 112
Transition Networks
SISGM1040-262D-LR User Guide
TFTP - Backup Configuration
You can get the current contents of the flash ROM from the switch and save them as a
file to TFTP.
1.
TFTP Server IP Address: Fill in the TFTP server IP.
2.
Backup File Name: Fill the file name.
3.
Click Apply .
Backup Configuration interface
33577 Rev. B
www.transition.com
Page 60 of 112
Transition Networks
SISGM1040-262D-LR User Guide
System Event Log – Syslog Configuration
Configure the system event mode to collect system log.
1.
Syslog Client Mode: Select the system log mode – Client Only, Server Only, or
Both.
2.
System Log Server IP Address: Assign the system log server IP.
3.
When Syslog Client Mode is set as Client Only, the system event log will only be
reserved in the switch’s RAM until next reboot. When Syslog Client Mode is set as
Server Only, the system log will only be sent to the syslog server and you have to
type the IP address in the Sysylog Server IP Address column. If the Syslog Client
Mode is set as Both, the system log will be reserved in the switch’s RAM and sent
to server.
4.
Click Reload
to refresh the events log.
5.
Click Clear to clear all current events log.
6.
After configuring, click Apply .
Syslog Configuration interface
33577 Rev. B
www.transition.com
Page 61 of 112
Transition Networks
SISGM1040-262D-LR User Guide
System Event Log - SMTP Configuration
You can set up the mail server IP, mail account, password, and forwarded email account
for receiving the event alert.
1.
Email Alert: enable or disable the email alert function.
2.
SMTP Server IP: set up the mail server IP address (when Email Alert enabled, this
function will then be available).
3.
Sender: key in an alias of the switch in complete email address format, e.g.
switch101@123.com, which is used for identifying where the event log comes from.
4.
Authentication: mark the check box to enable and configure the email
account/password for authentication (when Email Alert enabled, this function will
then be available).
5.
Mail Account: set up the email account, e.g. johnadmin, to receive the alert. It must
be an existing email account on the mail server, which you had set up in SMTP
Server IP Address field.
6.
Password: type in the password to the email account.
7.
Confirm Password: type in the password again for confirmation.
8.
Rcpt e-mail Address 1 ~ 6: you can also assign up to 6 e-mail accounts to receive
the alert.
9.
Click Apply .
33577 Rev. B
www.transition.com
Page 62 of 112
Transition Networks
SISGM1040-262D-LR User Guide
SMTP Configuration interface
33577 Rev. B
www.transition.com
Page 63 of 112
Transition Networks
SISGM1040-262D-LR User Guide
System Event Log - Event Configuration
When the Syslog/SMTP checkbox is ticked, the event log will be sent to the system log
server/SMTP server. Also, the particular port log (link up, link down, and both) events
can be sent to the system log server/SMTP server with the respective checkbox ticked.
After configuring, click ‘Apply’ to have the setting take effect.

System event selection: 4 selections – Device cold start, Device warm start,
SNMP Authentication Failure, and X-ring topology change. Mark the checkbox to
select the event. When selected events occur, the system will issue the logs.

Device cold start: When the device executes cold start action, the system will
issue a log event.

Device warm start: When the device executes warm start, the system will
issue a log event.

Authentication Failure: When the SNMP authentication fails, the system will
issue a log event.

X-ring topology change: When the X-ring topology has changed, the system
will issue a log event.

Port event selection: To have the drop-down menu items be available, the Syslog
Client Mode item on the Syslog Configuration tab and the E-mail Alert item on the
SMTP Configuration tab must be enabled first. Those drop-down menu items have
3 options—Link UP, Link Down, and Link UP & Link Down. Disable means no event
will be sent to the system log server/SMTP server.

Link UP: the system will issue a log message when port connection is up only.

Link Down: the system will issue a log message when port connection is down
only.

Link UP & Link Down: the system will issue a log message when port
connection is up and down.
33577 Rev. B
www.transition.com
Page 64 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Event Configuration interface
33577 Rev. B
www.transition.com
Page 65 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Fault Relay Alarm

Power Failure: Tick the check box to enable the function for lighting up the FAULT
LED on the panel when power fails.

Port Link Down/Broken: Tick the check box to enable the function for lighting up
the FAULT LED on the panel when port link-down or broken failure occurs.
Fault Relay Alarm interface
33577 Rev. B
www.transition.com
Page 66 of 112
Transition Networks
SISGM1040-262D-LR User Guide
SNTP Configuration
You can configure the SNTP (Simple Network Time Protocol) settings which allow you to
synchronize switch clock with an Internet time server.
1.
SNTP Client: Enable/disable SNTP function to get the time from the SNTP server.
2.
Daylight Saving Time: Enable/disable the daylight saving time function. When
enabled, you need to configure Daylight Saving Period.
3.
UTC Timezone: Set the switch location time zone. The following table lists the
different location time zone for your reference.
Local Time Zone
Conversion from UTC
Time at 12:00 UTC
November Time Zone
- 1 hour
11am
Oscar Time Zone
-2 hours
10 am
ADT - Atlantic Daylight
-3 hours
9 am
-4 hours
8 am
-5 hours
7 am
-6 hours
6 am
-7 hours
5 am
-8 hours
4 am
ALA - Alaskan Standard
-9 hours
3 am
HAW - Hawaiian Standard
-10 hours
2 am
Nome, Alaska
-11 hours
1 am
AST - Atlantic Standard
EDT - Eastern Daylight
EST - Eastern Standard
CDT - Central Daylight
CST - Central Standard
MDT - Mountain Daylight
MST - Mountain Standard
PDT - Pacific Daylight
PST - Pacific Standard
ADT - Alaskan Daylight
33577 Rev. B
www.transition.com
Page 67 of 112
Transition Networks
SISGM1040-262D-LR User Guide
CET - Central European
FWT - French Winter
MET - Middle European
+1 hour
1 pm
+2 hours
2 pm
BT - Baghdad, USSR Zone 2
+3 hours
3 pm
ZP4 - USSR Zone 3
+4 hours
4 pm
ZP5 - USSR Zone 4
+5 hours
5 pm
ZP6 - USSR Zone 5
+6 hours
6 pm
+7 hours
7 pm
+8 hours
8 pm
+9 hours
9 pm
+10 hours
10 pm
+12 hours
Midnight
MEWT - Middle European Winter
SWT - Swedish Winter
EET - Eastern European, USSR
Zone 1
WAST - West Australian
Standard
CCT - China Coast, USSR Zone
7
JST - Japan Standard, USSR
Zone 8
EAST - East Australian Standard
GST
Guam Standard, USSR Zone 9
IDLE - International Date Line
NZST - New Zealand Standard
NZT - New Zealand
4.
SNTP Sever URL: Set the SNTP server IP address.
5.
Switch Timer: Displays current time of the switch.
6.
Daylight Saving Period: Set up the Daylight Saving beginning time and ending
time. Both will be different in every year.
7.
Daylight Saving Offset (mins): For non-US and European countries, specify the
amount of time for day light savings.
8.
Click Apply .
33577 Rev. B
www.transition.com
Page 68 of 112
Transition Networks
SISGM1040-262D-LR User Guide
SNTP Configuration interface
33577 Rev. B
www.transition.com
Page 69 of 112
Transition Networks
SISGM1040-262D-LR User Guide
IP Security
IP security function allows users to assign 10 specific IP addresses that have permission to
access the switch through the web browser for the securing switch management.

IP Security Mode: When this option is enabled, the Enable HTTP Server and Enable
Telnet Server check boxes will then be available.

Enable HTTP Server: When this check box is ticked, the IP addresses among Security IP1
~ IP10 will be allowed to access via HTTP service.

Enable Telnet Server: When ticked, the IP addresses among Security IP1 ~ IP10 will be
allowed to access via Telnet service.

Security IP 1 ~ 10: The system allows users to assign up to 10 specific IP addresses for
access security. Only these 10 IP addresses can access and manage the switch through
HTTP/Telnet services.

Click
Apply
to have the configuration take effect.
NOTE Remember to execute the “Save Configuration” action, otherwise the new configuration
will lose when switch powers off.
33577 Rev. B
www.transition.com
Page 70 of 112
Transition Networks
SISGM1040-262D-LR User Guide
IP Security interface
33577 Rev. B
www.transition.com
Page 71 of 112
Transition Networks
SISGM1040-262D-LR User Guide
User Authentication
Here you can change login user name and password for management security purposes.
1.
User name: Key in the new user name (The default is “root”)
2.
Password: Key in the new password (The default is “root”)
3.
Confirm password: Re-type the new password
4.
And then, click Apply .
User Authentication interface
33577 Rev. B
www.transition.com
Page 72 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Port Statistics
The following information provides the current port statistics information.

Port: Port number index.

Type: Displays the media type of the port.

Link: The status of linking—‘Up’ or ‘Down’.

State: It’s set by the Port Control interface. When the state is disabled, the port will not
transmit or receive any packets.

Tx Good Packet: The counts of transmitting good packets via this port.

Tx Bad Packet: The counts of transmitting bad packets (including undersize [less than 64
bytes], oversize, CRC Align errors, fragments and jabbers packets) via this port.

Rx Good Packet: The counts of receiving good packets via this port.

Rx Bad Packet: The counts of receiving bad packets (including undersize [less than 64
bytes], oversize, CRC error, fragments and jabbers) via this port.

Tx Abort Packet: The aborted packet while transmitting.

Packet Collision: The counts of collision packet.

Packet Dropped: The counts of dropped packet.

Rx Bcast Packet: The counts of broadcast packet.

Rx Mcast Packet: The counts of multicast packet.

Click Clea to clean all counts.
Port Statistics interface
33577 Rev. B
www.transition.com
Page 73 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Port Control
Select one port and click the pull-down menu to configure parameters that control the
transmitting/receiving packets.
1.
Port: select the port that you want to configure.
2.
State: Current port status. The port can be set to disable or enable mode. If the port
setting is set as ‘Disable’, it will not receive or transmit any packets.
3.
Negotiation: set auto negotiation status of port.
4.
Speed: set the port link speed.
5.
Duplex: set full-duplex or half-duplex mode of the port.
6.
Flow Control: set flow control function as Enable or Disable in Full Duplex mode.
The default value is Enable.
7.
Security: When its state is ‘On’ that means this port accepts only one MAC address
which was configured to be a static MAC address.
8.
Click Apply .
Port Control interface
33577 Rev. B
www.transition.com
Page 74 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Port Trunk
The Link Aggregation Control Protocol (LACP) provides a standardized means for exchanging
information between Partner Systems on a link to allow their Link Aggregation Control instances
to reach agreement on the identity of the Link Aggregation Group to which the link belongs,
move the link to that Link Aggregation Group, and enable its transmission and reception
functions in an orderly manner. Link aggregation lets you group up to 4 ports into one dedicated
connections. This feature can expand bandwidth to a device on the network. LACP operation
requires full-duplex mode, more detail information refers to IEEE 802.3ad.
Aggregator setting
1.
System Priority: A value used to identify the active LACP. The switch with the lowest value
has the highest priority and is selected as the active LACP.
2.
Group ID: There are three trunk groups to provide configure. Choose the "Group ID" and
click Select .
3.
LACP: If enable, the group is LACP static trunk group. If disable, the group is local static
trunk group. All ports support LACP dynamic trunk group. If connecting to the device that
also supports LACP, the LACP dynamic trunk group will be created automatically.
4.
Work ports: allow max four ports can be aggregated at the same time. With LACP static
trunk group, the exceed ports are standby and can be aggregated if work ports fail. If it is
local static trunk group, the number of ports must be the same as the group member ports.
5.
Select the ports to join the trunk group. Allow max four ports can be aggregated at the same
time. Click
Add
to add the port. To remove unwanted ports, select the port and click
Remove .
6.
If LACP enable, you can configure LACP Active/Passive status in each ports on State
Activity page.
7.
Click Apply .
8.
Use Delete
33577 Rev. B
to delete Trunk Group. Select the Group ID and click Delete .
www.transition.com
Page 75 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Port Trunk—Aggregator Setting interface
Aggregator Information
When you have set up the aggregator setting with LACP disabled, you will see the local
static trunk group information here.
Port Trunk – Aggregator Information interface
33577 Rev. B
www.transition.com
Page 76 of 112
Transition Networks
SISGM1040-262D-LR User Guide
State Activity
When you have setup the LACP aggregator, you can configure port state activity. You can mark
or un-mark the port. When you mark the port and click
Apply , the port state activity will
change to Active. Opposite is Passive.

Active: The port automatically sends LACP protocol packets.

Passive: The port does not automatically send LACP protocol packets, and responds only
if it receives LACP protocol packets from the opposite device.
[NOTE]
1. A link having either two active LACP ports or one active port can perform dynamic
LACP trunk.
2. A link has two passive LACP ports will not perform dynamic LACP trunk because both
ports are waiting for an LACP protocol packet from the opposite device.
3. If you are active LACP’s actor, after you have selected trunk port, the active status will
be created automatically.
Port Trunk – State Activity interface
33577 Rev. B
www.transition.com
Page 77 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Port Mirroring
The Port mirroring is a method for monitoring traffic in switched networks. Traffic through ports
can be monitored by one specific port. That means traffic goes in or out monitored (source) ports
will be duplicated into mirror (destination) port.

Destination Port: There is only one port can be selected to be destination (mirror) port for
monitoring both RX and TX traffic which come from source port. Or, use one of two ports for
monitoring RX traffic only and the other one for TX traffic only. User can connect mirror port
to LAN analyzer or Netxray

Source Port: The ports that user wants to monitor. All monitored port traffic will be copied
to mirror (destination) port. User can select multiple source ports by checking the RX or TX
check boxes to be monitored.

And then, click
Apply .
Port Trunk – Port Mirroring interface
33577 Rev. B
www.transition.com
Page 78 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Rate Limiting
You can set up every port’s bandwidth rate and frame limitation type.

Ingress Limit Frame type: Select the frame type that you want to filter. The frame types
have
4
options
for
selecting:
All,
Broadcast/Multicast/Flooded
Unicast,
Broadcast/Multicast and Broadcast only.
Broadcast/Multicast/Flooded Unicast, Broadcast/Multicast and Bbroadcast only types
are only for ingress frames. The egress rate only supports the type of ‘All’.
Rate Limiting interface

All the ports support port ingress and egress rate control. For example, assume port 1 is
10Mbps, users can set it’s effective egress rate as 1Mbps, ingress rate as 500Kbps. The
switch performs the ingress rate by packet counter to meet the specified rate
4.

Ingress: Enter the port effective ingress rate (The default value is “0”)

Egress: Enter the port effective egress rate (The default value is “0”)
And then, click
33577 Rev. B
Apply
to apply the settings.
www.transition.com
Page 79 of 112
Transition Networks
SISGM1040-262D-LR User Guide
VLAN configuration
A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain, which
would allow you to isolate network traffic, so only the members of the VLAN will receive traffic
from the same VLAN members. Basically, creating a VLAN from a switch is logically equivalent
to reconnecting a group of network devices to another Layer 2 switch. However, all the network
devices are still plugged into the same switch physically.
The industrial switch supports port-based and 802.1Q (tagged-based) VLAN. The default
configuration of VLAN operation mode is “Disable”.
VLAN Configuration interface
33577 Rev. B
www.transition.com
Page 80 of 112
Transition Networks
SISGM1040-262D-LR User Guide
VLAN configuration - Port-based VLAN
Packets can go among only members of the same VLAN group. Note all unselected ports are
treated as belonging to another single VLAN. If the port-based VLAN enabled, the VLAN-tagging
is ignored.
In order for an end station to send packets to different VLAN groups, it itself has to be either
capable of tagging packets it sends with VLAN tags or attached to a VLAN-aware bridge that is
capable of classifying and tagging the packet with different VLAN ID based on not only default
PVID but also other information about the packet, such as the protocol.
VLAN – Port Based interface

Click Add
to add a new VLAN group(The maximum VLAN group is up to 256 VLAN
groups)

Entering the VLAN name, group ID and grouping the members of VLAN group

And then, click
33577 Rev. B
Apply
www.transition.com
Page 81 of 112
Transition Networks
SISGM1040-262D-LR User Guide
VLAN—Port Based Add interface

You will see the VLAN displays.

Use

Use Edit
Delete
Note
to delete unwanted VLAN.
to modify existing VLAN group.
Remember to execute the ‘Save Configuration’ action, otherwise the new
configuration will lose when switch power off.
33577 Rev. B
www.transition.com
Page 82 of 112
Transition Networks
SISGM1040-262D-LR User Guide
802.1Q VLAN
Tag-based VLAN is an IEEE 802.1Q specification standard. Therefore, it is possible to create a
VLAN across devices from different switch venders. IEEE 802.1Q VLAN uses a technique to
insert a “tag” into the Ethernet frames. Tag contains a VLAN Identifier (VID) that indicates the
VLAN numbers.
You can create Tag-based VLAN, and enable or disable GVRP protocol. There are 256 VLAN
groups to provide configure. Enable 802.1Q VLAN, the all ports on the switch belong to default
VLAN, VID is 1. The default VLAN can’t be deleted.
GVRP allows automatic VLAN configuration between the switch and nodes. If the switch is
connected to a device with GVRP enabled, you can send a GVRP request using the VID of a
VLAN defined on the switch; the switch will automatically add that device to the existing VLAN.
802.1q VLAN interface
33577 Rev. B
www.transition.com
Page 83 of 112
Transition Networks
SISGM1040-262D-LR User Guide
802.1Q Configuration
1.
Enable GVRP Protocol: check the check box to enable GVRP protocol.
2.
Select the port that you want to configure.
3.
Link Type: There are 3 types of link type.

Access Link: Single switch only, allows user to group ports by setting the same VID to
those ports.

Trunk Link: The extended application of Access Link. While the ports are set in this
type, they can forward the packets with specified tag among the switches which are
included in the same VLAN group.

Hybrid Link: Both Access Link and Trunk Link are available.
4.
Untagged VID: assign the untagged frame VID.
5.
Tagged VID: assign the tagged frame VID.
6.
Click
7.
You can see each port setting in the below table on the screen.
Apply
Group Configuration
Edit the existing VLAN Group.
1.
Select the VLAN group in the table list.
2.
Click
33577 Rev. B
Edit
www.transition.com
Page 84 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Group Configuration interface
3.
You can Change the VLAN group name and VLAN ID.
4.
Click Apply .
Group Configuration interface
33577 Rev. B
www.transition.com
Page 85 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Rapid Spanning Tree
The Rapid Spanning Tree Protocol (RSTP) is an evolution of the Spanning Tree Protocol and
provides for faster spanning tree convergence after a topology change. The system also
supports STP and the system will auto detect the connected device that is running STP or RSTP
protocol.
RSTP - System Configuration

User can view spanning tree information about the Root Bridge.

User can modify RSTP state. After modification, click

Apply .
RSTP mode: User must enable or disable RSTP function before configure the related
parameters.

Priority (0-61440): A value used to identify the root bridge. The bridge with the lowest
value has the highest priority and is selected as the root. The value must be a multiple
of 4096 according to the protocol standard rule.

Max Age (6-40): The number of seconds a bridge waits without receiving Spanningtree Protocol configuration messages before attempting a reconfiguration. Enter a
value between 6 through 40.

Hello Time (1-10): The time that controls switch sends out the BPDU packet to check
RSTP current status. Enter a value between 1 through 10.

Forward Delay Time (4-30): The number of seconds a port waits before changing
from its Rapid Spanning-Tree Protocol learning and listening to STP states to the
forwarding state. Enter a value between 4 through 30.
Note
Follow the rule to configure the MAX Age, Hello Time, and Forward Delay Time.
2 x (Forward Delay Time value – 1) > = Max Age value >= 2 x (Hello Time
value +1)
33577 Rev. B
www.transition.com
Page 86 of 112
Transition Networks
SISGM1040-262D-LR User Guide
RSTP System Configuration interface
RSTP - Port Configuration
You can configure path cost and priority of every port.
1. Path Cost: The cost of the path to the other bridge from this transmitting bridge at the
specified port. Enter a number 1 through 200000000.
2. Priority: Decide which port should be blocked by priority in LAN. Enter a number 0 through
240. The value of priority must be the multiple of 16.
3. P2P: Some of the rapid state transactions that are possible within RSTP are dependent upon
whether the port concerned can only be connected to exactly one other bridge (i.e. it is
served by a point-to-point LAN segment), or can be connected to two or more bridges (i.e. it
is served by a shared medium LAN segment). This function allows the P2P status of the link
to be manipulated administratively. True is P2P enabling. False is P2P disabling.
4. Edge: The port directly connected to end stations cannot create bridging loop in the network.
To configure the port as an edge port, set the port to “True” status.
5. Non Stp: The port includes the STP mathematic calculation. True is not including STP
mathematic calculation. False is including the STP mathematic calculation.
6. Click Apply .
33577 Rev. B
www.transition.com
Page 87 of 112
Transition Networks
SISGM1040-262D-LR User Guide
RSTP Port Configuration interface
SNMP Configuration
Simple Network Management Protocol (SNMP) is the protocol developed to manage nodes
(servers, workstations, routers, switches and hubs etc.) on an IP network. SNMP enables
network administrators to manage network performance, find and solve network problems, and
plan for network growth. Network management systems learn of problems by receiving traps or
change notices from network devices implementing SNMP.
33577 Rev. B
www.transition.com
Page 88 of 112
Transition Networks
SISGM1040-262D-LR User Guide
System Configuration

Community Strings
You can define a new community string set or remove unwanted community string.
1.
String: Fill the name of string.
2.
RO: Read only. Enables requests accompanied by this string to display MIB-object information.
3.
RW: Read write. Enables requests accompanied by this string to display MIB-object information and
to set MIB objects.
1.
Click Add .
2.
To remove the community string, select the community string that you have defined and
click Remove . You cannot edit the name of the default community string set.

Agent Mode: Select the SNMP version that you want to use it. And then click Change to switch to
the selected SNMP version mode.
SNMP System Configuration interface
33577 Rev. B
www.transition.com
Page 89 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Trap Configuration
A trap manager is a management station that receives traps, the system alerts generated by the
switch. If no trap manager is defined, no traps will issue. Create a trap manager by entering the
IP address of the station and a community string. To define management stations as trap
manager and enter SNMP community strings and selects the SNMP version.
1. IP Address: Enter the IP address of trap manager.
2. Community: Enter the community string.
3. Trap Version: Select the SNMP trap version type—v1 or v2c.
4. Click Add .
5. To remove the community string, select the community string that you have defined and
click Remove . You cannot edit the name of the default community string set.
Trap Managers interface
33577 Rev. B
www.transition.com
Page 90 of 112
Transition Networks
SISGM1040-262D-LR User Guide
SNMPV3 Configuration
Configure the SNMP V3 function.
Context Table
Configure SNMP v3 context table. Assign the context name of context table. Click
context name. Click
Remove
to remove unwanted context name.
User Profile
Configure SNMP v3 user table..

User ID: Set up the user name.

Authentication Password: Set up the authentication password.

Privacy Password: Set up the private password.

Click

Click
Add
33577 Rev. B
to add context name.
Remove
to remove unwanted context name.
www.transition.com
Page 91 of 112
Add
to add
Transition Networks
SISGM1040-262D-LR User Guide
SNMP V3 configuration interface
33577 Rev. B
www.transition.com
Page 92 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Group Table
Configure SNMP v3 group table.

Security Name (User ID): Assign the user name that you have set up in user table.

Group Name: Set up the group name.

Click

Click
Add
to add context name.
Remove
to remove unwanted context name.
Access Table
Configure SNMP v3 access table.

Context Prefix: Set up the context name.

Group Name: Set up the group.

Security Level: Select the access level.

Context Match Rule: Select the context match rule.

Read View Name: Set up the read view.

Write View Name: Set up the write view.

Notify View Name: Set up the notify view.

Click

Click
Add
to add context name.
Remove
to remove unwanted context name.
MIBview Table
Configure MIB view table.

ViewName: Set up the name.

Sub-Oid Tree: Fill the Sub-OID.

Type: Select the type – exclude or included.

Click

Click
Add
33577 Rev. B
to add context name.
Remove
to remove unwanted context name.
www.transition.com
Page 93 of 112
Transition Networks
SISGM1040-262D-LR User Guide
QoS Configuration
You can configure Qos policy and priority setting, per port priority setting, COS and TOS setting.
QoS Policy and Priority Type

Qos Policy: select the Qos policy rule.

Using the 8,4,2,1 weight fair queue scheme: The switch will follow 8:4:2:1 rate to
process priority queue from High to lowest queue. For example, when the system
processes, 1 frame of the lowest queue, 2 frames of the low queue, 4 frames of the
middle queue, and 8 frames of the high queue will be processed at the same time in
accordance with the 8,4,2,1 policy rule.

Use the strict priority scheme: Always higher queue will be process first, except
higher queue is empty.

Priority Type: there are 5 priority type selections available. Disable means no priority type
is selected.

Port-base: the port priority will follow the Port-base that you have assigned – High, middle,
low, or lowest.


COS only: the port priority will only follow the COS priority that you have assigned.

TOS only: the port priority will only follow the TOS priority that you have assigned.

COS first: the port priority will follow the COS priority first, and then other priority rule.

TOS first: the port priority will follow the TOS priority first, and the other priority rule.
Click Apply .
33577 Rev. B
www.transition.com
Page 94 of 112
Transition Networks
SISGM1040-262D-LR User Guide
QoS Configuration interface
33577 Rev. B
www.transition.com
Page 95 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Port Base Priority
Configure per port priority level.

Port: Each port has 4 egress queues – High, Middle, Low, and Lowest.

Click Apply .
COS Configuration
Set up the COS priority level.

COS priority: Set up the COS priority level 0~7 with 4 egress queues: High, Middle, Low,
Lowest.

Click Apply .
TOS Configuration
Set up the TOS priority.

TOS priority: the system provides 0~63 TOS priority level. Each level has 4 types of
priority (egress queues) – high, middle, low, and lowest. The default value is “Lowest” priority for
each level. When the IP packet is received, the system will check the TOS level value in the IP
packet that has received. For example, user set the TOS level 25 as high, the system will check
the TOS value of the received IP packet. If the TOS value of received IP packet is 25(priority =
high), and then the packet priority will have highest priority.

Click Apply .
33577 Rev. B
www.transition.com
Page 96 of 112
Transition Networks
SISGM1040-262D-LR User Guide
IGMP Configuration
The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol
(IP) suite. IP manages multicast traffic by using switches, routers, and hosts that support IGMP.
Enabling IGMP allows the ports to detect IGMP queries and report packets and manage IP
multicast traffic through the switch. IGMP have three fundamental types of message as follows:
Message
Query
Description
A message sent from the querier (IGMP router or switch) asking for a
response from each host belonging to the multicast group.
A message sent by a host to the querier to indicate that the host wants to
Report
be or is a member of a given group indicated in the report message.
A message sent by a host to the querier to indicate that the host has quit
Leave Group
being a member of a specific multicast group.
The switch supports IP multicast. You can enable IGMP protocol via setting IGMP configuration
page to see the IGMP snooping information. IP multicast addresses are in the range of 224.0.0.0
through 239.255.255.255.

IGMP Protocol: Enable or disable the IGMP protocol.

IGMP Query: Select the IGMP query function as Enable or Auto to set the switch as a
querier for IGMP version 2 multicast network.

Click Apply .
33577 Rev. B
www.transition.com
Page 97 of 112
Transition Networks
SISGM1040-262D-LR User Guide
IGMP Configuration interface
X-Ring
X-Ring provides a faster redundant recovery than Spanning Tree topology. The action is similar
to STP or RSTP, but the algorithms are different.
In the X-Ring topology, every switch should enable X-Ring function and assign two member
ports for connecting to the ring. Only one switch in the X-Ring group would be set as the master
switch that one of the member ports would be blocked, called backup port, and another port is
called working port. Other switches in the X-Ring group are called working switches and their
two member ports are called working ports. When the failure of network connection occurs, the
backup port will automatically become a working port to recover from the failure.
The switch supports the function and interface for setting the switch as the ring master or slave
mode. The ring master can negotiate and place command to other switches in the X-Ring group.
If there are 2 or more switches in master mode, then software will select the switch with lowest
MAC address number as the ring master. The X-Ring master ring mode will be enabled by the
X-Ring configuration interface. Also, user can identify the switch as the ring master from the R.M.
LED panel of the LED panel on the switch.
The system also supports the coupling ring that can connect 2 or more X-Ring group for the
redundant backup function and dual homing function that prevent connection lose between XRing group and upper level/core switch.
33577 Rev. B
www.transition.com
Page 98 of 112
Transition Networks

SISGM1040-262D-LR User Guide
Enable X-Ring: To enable the X-Ring function. Marking the check box to enable the X-Ring
function.

Enable Ring Master: Mark the check box for enabling this machine to be a ring master.

1st & 2nd Ring Ports: Pull down the selection menu to assign two ports as the member
ports. The 1st Ring Port and 2nd Ring Port are basically assigned to be forwarding ports
except for the Ring Master switch. With the Ring Master switch, one of its two Ring Ports is
the blocking port and another one is the forwarding port. Once its forwarding port fails, the
system will automatically upgrade its blocking port to be the forwarding port of the Ring
Master switch.

Enable Coupling Ring: To enable the coupling ring function. Marking the check box to
enable the coupling ring function.

Coupling port: Assign the member port which is connected to the other ring group.

Control port: When Couple Ring check box is marked, you have to assign the control port
to form a couple-ring group between the two X-rings.

Enable Dual Homing: Set up one of the ports on the switch to be the Dual Homing port.
For a switch, there is only one Dual Homing port. Dual Homing only works while the X-Ring
function enabled.

And then, click
Apply
to apply the configuration.
X-ring Interface
33577 Rev. B
www.transition.com
Page 99 of 112
Transition Networks
Note
SISGM1040-262D-LR User Guide
When the X-Ring function enable, user must disable the RSTP. The X-Ring
function and RSTP function cannot exist in a switch at the same time.
Remember to execute the ‘Save Configuration’ action, otherwise the new
configuration will lose when switch power off.
33577 Rev. B
www.transition.com
Page 100 of 112
Transition Networks
SISGM1040-262D-LR User Guide
802.1X/Radius Configuration
802.1x is an IEEE authentication specification prevents the client from accessing the wireless
access point or wired switch until it provides authority, like the user name/password that are
verified by an authentication server.
System Configuration
After enabling the IEEE 802.1X function, you can configure the parameters of this function.
1.
IEEE 802.1x Protocol: Enable or disable 802.1x protocol.
2.
Radius Server IP: Set the Radius Server IP address.
3.
Server Port: Set the UDP destination port for authentication requests to the specified
Radius Server.
4.
Accounting Port: Set the UDP destination port for accounting requests to the specified
Radius Server.
5.
Shared Key: Set an encryption key for using during authentication sessions with the
specified radius server. This key must match the encryption key used on the Radius Server.
6.
NAS, Identifier: Set the identifier for the radius client.
7.
Click Apply .
802.1x System Configuration interface
33577 Rev. B
www.transition.com
Page 101 of 112
Transition Networks
SISGM1040-262D-LR User Guide
802.1x Port Configuration
You can configure 802.1x authentication state for each port. The State provides Disable, Accept,
Reject and Authorize.

Reject: The specified port is required to be held in the unauthorized state.

Accept: The specified port is required to be held in the Authorized state.

Authorized: The specified port is set to the Authorized or Unauthorized state in accordance
with the outcome of an authentication exchange between the Supplicant and the
authentication server.

Disable: When disabled, the specified port works without complying with 802.1x protocol.

Click Apply .
802.1x Per Port Setting interface
33577 Rev. B
www.transition.com
Page 102 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Misc Configuration
1.
Quiet Period: Set the period during which the port doesn’t try to acquire a supplicant.
2.
TX Period: Set the period the port wait for retransmit next EAPOL PDU during an
authentication session.
3.
Supplicant Timeout: Set the period of time the switch waits for a supplicant response to an
EAP request.
4.
Server Timeout: Set the period of time the switch waits for a server response to an
authentication request.
5.
Max Requests: Set the number of authentication that must time-out before authentication
fails and the authentication session ends.
6.
Reauth period: Set the period of time after which clients connected must be reauthenticated.
7.
Click Apply .
802.1x Misc Configuration interface
33577 Rev. B
www.transition.com
Page 103 of 112
Transition Networks
SISGM1040-262D-LR User Guide
MAC Address Table
Use the MAC address table to ensure the port security.
Static MAC Address
You can add a static MAC address; it remains in the switch's address table, regardless of
whether the device is physically connected to the switch. This saves the switch from having to
re-learn a device's MAC address when the disconnected or powered-off device is active on the
network again. You can add / modify / delete a static MAC address.

Add the Static MAC Address
You can add static MAC address in switch MAC table.
1.
MAC Address: Enter the MAC address of the port that should permanently forward traffic,
regardless of the device network activity.
2.
Port No.: Pull down the selection menu to select the port number.
3.
Click
4.
If you want to delete the MAC address from filtering table, select the MAC address and
Add
.
click Delete .
Static MAC Addresses interface
33577 Rev. B
www.transition.com
Page 104 of 112
Transition Networks
SISGM1040-262D-LR User Guide
MAC Filtering
By filtering MAC address, the switch can easily filter pre-configure MAC address and reduce the
un-safety. You can add and delete filtering MAC address.
MAC Filtering interface
1.
MAC Address: Enter the MAC address that you want to filter.
2.
Click
3.
If you want to delete the MAC address from filtering table, select the MAC address and
Add
.
click Delete .
All MAC Addresses
You can view the connected device’s MAC address and related devices’ MAC address to the
port.
1.
Select the port.
2.
The selected port of static MAC address information will be displayed here.
3.
Click
Clear MAC Table
to clear the current port static MAC address information on
screen.
33577 Rev. B
www.transition.com
Page 105 of 112
Transition Networks
SISGM1040-262D-LR User Guide
All MAC Address interface
Factory Default
Reset switch to default configuration. Click Reset
to reset all configurations to the default
value.
Factory Default interface
33577 Rev. B
www.transition.com
Page 106 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Save Configuration
Save all configurations that you have made in the system. To ensure the all configuration will be
saved. Click
Save
to save the all configuration to the flash memory.
Save Configuration interface
System Reboot
Reboot the switch in software reset. Click
Reboot
to reboot the system.
System Reboot interface
33577 Rev. B
www.transition.com
Page 107 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Troubleshooting

Verify that the switch is supplied with correct power input. Don’t use the power adapter with
DC output higher than power ratings of the equipment.

Select the proper UTP cable to construct user network. Please check that is using the right
cable. Use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45
connections: 100Ω Category 3, 4 or 5 cable for 10Mbps connections,
100Ω Category 5 cable for 100Mbps connections, or 100Ω Category 5e/6 cable for
1000Mbps connections. Also be sure that the length of any twisted-pair connection does
not exceed 100 meters (328 feet).

Diagnosing LED Indicators: The switch can be easily monitored through panel indicators,
which describes common problems users may encounter and where users can find possible
solutions.

If the power indicator does not light up when the power cord is plugged in, users may have
a problem with power cord. Then check for loose power connections, power losses or
surges at power outlet. If users still cannot resolve the problem, contact local dealer for
assistance.

If the Industrial switch LED indicators are normal and the connected cables are correct but
the packets still cannot transmit. Please check user system’s Ethernet devices’
configuration or status.
33577 Rev. B
www.transition.com
Page 108 of 112
Transition Networks
SISGM1040-262D-LR User Guide
Technical Specifications
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX
IEEE802.3ab 1000Base-T
IEEE802.3z Gigabit fiber
IEEE802.3x Flow Control and Back Pressure
Standard
IEEE802.3ad Port trunk with LACP
IEEE802.1d Spanning Tree
IEEE802.1w Rapid Spanning Tree
IEEE802.1p Class of Service
IEEE802.1Q VLAN Tag
IEEE 802.1x User Authentication (Radius)
IEEE802.1ab LLDP**
RFC 1215 Trap, RFC 1213 MIBII, RFC 1157 SNMP MIB, RFC 1493
SNMP MIB
Bridge MIB, RFC 2674 VLAN MIB, RFC 1643, RFC 1757, RSTP MIB,
Private MIB, LLDP MIB**
Back-Plane (Switching
Fabric)
Packet Throughput
Ability
Technology
16 Gbps
23.8Mpps at 64bytes
Store and forward switching architecture
14,880 pps for 10Base-T Ethernet port
Transfer Rate
148,800 pps for 100Base-TX/FX Fast Ethernet port
1,488,000 pps for Gigabit Ethernet port
Packet Buffer
1Mbits
MAC Address
8K MAC entries
Flash ROM
4Mbytes
33577 Rev. B
www.transition.com
Page 109 of 112
Transition Networks
DRAM
SISGM1040-262D-LR User Guide
32Mbytes
10/100/1000TX: 6 ports RJ-45 with Auto MDI/MDI-X function
Connector
10/100/1000T/Mini-GBIC Combo: 2 x RJ-45 + 2 x 100/1000 SFP sockets
RS-232 interface: RJ-45 type
10/100/1000Base-T:
2-pair UTP/STP Cat. 5e/6 cable EIA/TIA-568 100-ohm (100m)
Network Cable
SFP (Mini-GBIC):
Multi-mode: 50/125μm~62.5/125μm
Single-mode: 9/125μm
Protocol
CSMA/CD
RJ-45: Link/Activity (Green), Speed 1000M (Green)
LED
SFP (Mini-GBIC): Link/Activity (Green)
System: Power (Green), Power 1 (Green), Power 2 (Green), Fault (Red),
Master (Green)
Power Supply
Power Consumption
Relay Alarm
12 ~48 VDC
Redundant power and removable terminal block
18 Watts
One relay output for port breakdown and power fail
Alarm Relay current carry ability: 1A @ DC24V
Installation
DIN-rail and wall mountings
Operating Temp.
-10ºC to 60ºC (14ºF to 140ºF)
Operating Humidity
5% to 95% (Non-condensing)
Storage Temperature
-40ºC to 85ºC
Case Dimensions
IP-30, 72 mm (W) x 152mm (H) x 105 mm (D)
33577 Rev. B
www.transition.com
Page 110 of 112
Transition Networks
SISGM1040-262D-LR User Guide
FCC Class A
CE EN61000-4-2 (ESD)
CE EN61000-4-3 (RS)
CE EN61000-4-4 (EFT)
CE EN61000-4-5 (Surge)
EMI
CE EN61000-4-6 (CS)
CE EN61000-4-8
CE EN61000-4-11
CE EN61000-4-12
CE EN61000-6-2
CE-EN61000-6-4
Safety
UL, cUL, CE/EN60950-1
(suitable for use in Class I / Division 2 locations)
IEC60068-2-32 (Free fall)
Stability testing
IEC60068-2-27 (Shock)
IEC60068-2-6 (Vibration)
Supports X-Ring, Dual Homing, and Couple Ring
X-Ring
Provides redundant backup feature and recovery time from failure less than
20ms
Port based VLAN
VLAN
IEEE802.1Q Tag VLAN (256 entries)/VLAN ID (up to 4 K, VLAN ID can be
assigned from 1 to 4096)
GVRP (256 Groups)
Port Trunk with LACP
Class of Service
Quality of Service
Spanning Tree
Port Mirroring
IGMP
33577 Rev. B
LACP Port Trunk: 4 Trunk groups/Maximum 4 trunk members
IEEE802.1p class of service
Per port provides 4 priority queues.
The QoS determined by port, tag, and IPv4 Type of Service, IPv4 Different
Service
IEEE802.1d spanning tree
IEEE802.1w rapid spanning tree.
TX packet only, RX packet only, Both of TX and RX packet
IGMP snooping v1, v2
Up to 256 multicast groups and IGMP query
www.transition.com
Page 111 of 112
Transition Networks
SISGM1040-262D-LR User Guide

Ingress packets filter and egress packet limit.

The egress rate control supports all of packet types and the limit rate
ranging fromf 100 kbps to 250Mbps
Bandwidth Control

Ingress filter packet type combination rules for
Broadcast/Multicast/Flooded Unicast packet, Broadcast/Multicast
packet, Broadcast packet only and all of packet.

IP Security
Login Security
SNTP
The ingress packet filter rate ranging fromf 100 kbps to 250Mbps
Supports 10 IP addresses that have permission to access the switch
management and to prevent unauthorized intruder
Supports IEEE802.1X Authentication/RADIUS
Supports Simple Network Time Protocol to synchronize system clock in
Internet.
Up to 3 Trap stations
Cold start
Port link up
Port link down
SNMP Trap
Authentication Failure
Private Trap for power status
Port Alarm configuration
Fault alarm
X-Ring topology change
DHCP Client
Provide DHCP Client/ DHCP Server/IP Relay functions
Firmware Update
TFTP firmware update
Configuration
Upload/Download
33577 Rev. B
Supports binary configuration file for system quick installation
www.transition.com
Page 112 of 112