12
6
20
5 15 16 9
2
>>I
REL
MODE
R
E
II
M
RD
ON
5
AV IN-OUT
T
AS
S
RP
PT
Y
IXB
6
AF
STOP
SUBW
2
3
TA
2Z
4
>
E N G L I S H
3
OSD-SET UP
AS-FS
I>>
MUTE
13 1
14
4
21
BAND
19
MCD 775
17 10
4x 75W
8
DISP-MENU
7
18
11
1. MUTE / POWER
2. EJECT
3. PANEL RELEASE
4. AUDIO MENU BUTTON / CD, DVD OK. BUTTON
5. MODE
6. ENCODER VOLUME
7. 3,5MM A/V IN JACK
8. SUBWOOFER / TUNER AF
9. 2 ZONE / TUNER TA
10. 1X-BASS / TUNER PTY
11.TUNER PS AS / CD SET-UP / DVD OSD SET-UP
12.TUNER M1 MEMORY 1 / CD PAUSE PLAY / DVD PAUSE PLAY
13.TUNER M2 MEMORY 2 / CD STOP / DVD STOP
14.TUNER M3 MEMORY 3 / CD REPEAT OFF, REPEAT TRACK, REPEAT
DISC / DVD REPEAT OFF, REPEAT CHAPTER, REPEAT TITLE
15.TUNER M4 MEMORY 4 / CD RANDOM FOLDER / DVD SHORT
PRESS M4 --> DVD MENU
16.TUNER M5 MEMORY 5
17.TUNER M6 MEMORY 6 / DVD AUDIO
18. DISPLAY MENU
19.TUNER BAND
20.TUNER SEEK UP TUNE UP / CD FILE/TRACK UP FAST FORWARD /
DVD NEXT FAST FORWARD
21.TUNER SEEK DOWN,TUNE DOWN / CD FILE/TRACK DOWN
FAST BACKWARD / DVD BACK FAST BACKWARD
1
S P E C I F I C AT I O N S
RADIO SECTION
GENERAL
Power Supply
Polarity
Speaker impedance
Power Output
DVD / CD PLAYER
Usable disc
DC 11 -14,4V
Negative Ground
4 ohms
4 x 75W
FM
Frequency Range
Usable Sensitivity
Stereo Separation
S/N Ratio
87.5-108 Mhz
Better than 15dB at S/N 30 dB
25 dB at 1KHz
50 dB
DVD+/-R, DVD+/-RW, CD, CD-R,
CD-RW, USB, SD
AM / MW
Frequency Range
Usable Sensitivity
S/N Ratio
522-1620 Khz
Better than 40dB
40 dB
Sampling frequency
No of quantization bits
Frequency
20-20,000Hz
Number of channels
2 stereo
S/N Ratio
90dB
REMARK :
Specifications subject to change without notice.
E N G L I S H
D I S C P L AY
2
PRECAUTIONS
• Use only in a 12-volt DC negative-ground electrical system.
• Disconnect the vehicle's negative battery terminal while mounting and connecting the unit.
• When replacing the fuse, be sure to use one with an identical amperage rating.
• Using a fuse with a higher amperage rating may cause serious damage to the unit.
• DO NOT attempt to disassemble the unit. Laser beams from the optical pickup are dangerous to the eyes.
• Make sure that pins or other objects do not get inside the unit; they may cause malfunctions, or create safety
hazards such as electrical shock or laser beam exposure.
• If you have parked the car for a long time in hot or cold weather, wait until the
temperature in the car become normal before operating the unit.
• Keep the volume at a level at which you can hear outside warning sounds (horns
sirens, etc.).
CD NOTES
• Playing a defective or dusty CD can cause dropouts in sound.
• Hold CDs as illustrated.
• DO NOT touch the unlabeled side.
• DO NOT attach any seal, label or data protection sheet to either side of a disc.
• DO NOT expose a CD to direct sunlight or excessive heat.
• Wipe a dirty CD from the center outward with a cleaning cloth.
• Never use solvents such as benzine or alcohol.
• This unit cannot play 3-inch ( 8cm ) CDs.
• NEVER insert a 3-inch CD contained in the adapter or an irregularly shaped CD.
• The unit may not be able to eject it, resulting in a malfunction.
BEFORE OPERATION
• DO NOT raise the volume level too much, as this will block outside sounds, making
driving dangerous.
• Stop the car before performing any complicated operation.
CAUTION
DO NOT open covers and do not repair by yourself. Consult the dealer or an experienced technician for help.
INSTALLATION PROCEDURES
First complete the electrical connections, and then check them for correctness.
ANTI-THEFT SYSTEM
This unit is equipped with a detachable
panel.
Removing this panel makes the radio
totally inoperable.
REMOVING THE PANEL
1. Switch off the power of the unit.
2. Remove the detachable panel (REL
button).
3. Gently press the button of the case
and open the cover. Place the panel
into the case and take it with you
when you leave the car.
INSTALL DETACHABLE PANEL
1.Fix right part of face plate in the right
part of panel slot of the unit.
2.Press down the left side of the face
plate until it clicks into the panel slot
of the unit.
REMOVE THE UNIT
Switch of the power of the unit.
1. Remove the panel and the trim plate.
2. Insert both T-Keys into hole in front of
the set until they lock.
3. Pull out the unit.
1. Insert mounting bracket into the
dashboard, and bend the mounting
tabs out with a screwdriver. (Make
sure that lock lever is flush with
the mounting bracket. Not
projecting outward)
2. Secure the rear of the unit After
fixing mounting bolt and power
connector, fix the rear of the unit
to the car body by rubber cushion.
3. Insert trimplate
WIRING
DIAGRAM-AUDIO/VIDEO
CONNECTIONS
3
E N G L I S H
4
WIRING DIAGRAM-POWER/SPEAKERS
(ISO + SMALL CONNECTOR)
PA N E L O P E N / C L O S E O P E R AT I O N
This unit is equipped with the most advanced full logic motorized slide down system.You can enjoy this advance
technology with just a single press of the “OPEN” button Please read carefully the following operation instruction
before operating the unit.
OPEN / CLOSE THE PANEL
Press the Open button to slide down (open) a closed panel or to slide up (close) an opened panel.
LOADING A CD
When the panel is in the slide down position, the disc slot becomes accessible. Insert a CD through the disc slot, the
CD will be automatically loaded and the panel will also close automatically & playback will begin. If no CD is inserted,
press Open button again to slide up(close) the panel.
EJECTING A CD
Press Open button to slide down the panel, if a CD is loaded, it will be ejected automatically. No further key press is
needed. If the ejected CD is not being removed, after 10 seconds it will be reloaded automatically. And the panel will
automatically slide up after disc has been reloaded.Warning : If the ejected disc remains in the slot, the Open button
will not function, so closing the panel by using Open button is prevented unless the disc is removed or reloaded.
CAUTION
A) Please always use the “OPEN” button to slide up/ down the front panel. Please never try to slide up or down the
front panel manually, this will cause serious & permanent damage to the slide down mechanism, and this will void the
warranty.
B) Please do not try to detach / remove the front panel ( by pressing the detach button ) or attach the front panel
when the panel is in the slide down position.This may cause serious & permanent damage to the unit & panel. Only
attach or detach the front panel when the panel is in the slide up position.
5
3
12
6
20
PA N E L
FUNCTION
REMOTE
5 15 16 9
FUNCTIONS
2
>>I
REL
MODE
R
E
ON
>
II
RD
M
5
AV IN-OUT
AS
S
T
RP
PT
Y
6
IXB
3
AF
SUBW
2
TA
2Z
4
STOP
E N G L I S H
CONTROL
OSD-SET UP
AS-FS
6
I>>
MUTE
13 1
14
4
21
BAND
19
MCD 775
17 10
8
4x 75W
DISP-MENU
7
18
7
11
E N G L I S H
B A S I C O P E R AT I O N S
3) PANEL RELEASE BUTTON (REL)
Press this button to remove the control panel.
1) POWER ON/OFF BUTTON
Long press the POWER button or Short Press any other button on the front of the unit (except the Open/Eject) to
turn On the unit. Long press the POWER button to turn Off the unit.
1) MUTE BUTTON
Short Press the MUTE button to mute the audio output, and “Mute” will appear on the display. Press the mute button
again to restore the audio output to the previous level.
Please refer to the related description in “Audio Operation of Sub-woofer” for details operation of the
Subwoofer control !
The Subwoofer Level and Low Pass Filter control will only appear in the Audio Menu only if the Subwoofer
function is currently activated 'On”.
8
8) SUB-WOOFER (SUB-W)
Long Press the SUB-W button to activate the Sub-woofer function On, and “Sub-woofer” will appear on the LCD
display for 3 seconds. press the SUB-W button again to turn off the Sub-woofer function.
10) iX-BASS BUTTON (iX-Bass )
Long Press the iX-Bass button to turn on the IX-Bass function, and “iX-Bass” will appear in the LCD display for 3
seconds. Press the iX-Bass button again to turn off the IX-Bass function
Please refer to the related description in “Audio Operation of iX-Bass” for details operation of iX-Bass
control
The IX-Bass Boost Level control will only appear in the Audio Menu only if the iX-Bass function is currently
activated 'On”.
5) MODE BUTTON (MODE)
Short Press the MODE button to select a different mode of operation as indicated on the display panel. Available modes
include Tuner, DVD, Card(SD/MMC Card), USB, AV IN-1 and AV IN -2
6) ENCODER VOLUME BUTTON
To increase the volume, rotate the volume control knob clockwise.To decrease the volume, rotate the volume control
knob counter clockwise.When the volume is adjusted, the volume level is shown on the display panel as a number
ranging from 00 (lowest) to 46 (highest).
FRONT PANEL A/V IN JACK
The unit is allowed to connect with external Audio / Video system such
like Digital Camera or Game Console.You can connect the external A/V
system through the A/V in jack on front panel. After connect with
external A/V system, pressing mode to “A/V In” to enjoy this external
A/V system on this unit.
AV IN-OUT
OSD-SET UP
AS-FS
DISP-MENU
The unit only supports the 3.5mm A/V Jack Pin Assignment shown as the diagram.
The unit supports A/V out thrue the A/V Jack on front panel. For more details of
operation, please refer to “Menu operation-AV Jack”.
9
E N G L I S H
10
DISPLAY / MENU BUTTON
This DISPLAY inter-change button can be used to interchange between the 2 types of DISPLAY INTERFACE, the 'Image
Display Interface” & 'Big Font Display interface'.This is useful when playing a CD or MP3 or WMA or other music disc
and if user prefers to see the CD Track no / MP3 File number and elapse time with bigger numerical fonts, the Big Font
Display offers a better read out for the numerical display. User can press the DISP button to inter-change from Image
Display
DATE SET
Once in Date Set mode, User can use the Encoder Vol Knob to adjust the Date / Month / Year. Short press the AUDIO
button to confirm the entry and move to the next entry.
CLOCK
The time of the clock is set to 12:00 by default. User can adjust the time by rotate the Encoder Vol knob clockwise to
adjust the minute and rotate the Encoder Vol knob anticlockwise
to adjust the hour.
If the unit is equipped with the OPTIONAL RDS Function, the clock will be automatically updated by the RDS
roadcasting, provided if the RDS broadcast does include the clock information ( RDS CT FUNCTION )
TIME FORM
"12H" is the default setting. User can use the Encoder Vol Knob to choose the Time Format between “12 Hours” & “24
Hours”
Image Display Interface
Big Font Display Interface
Caution:
In some countries, it's unlawful to operate a vehicle while video is displayed in the driver's viewing area. Please always
switch the unit's display to "Big Font Type Display" mode by pressing the DISP/MENU button while driving. For safety
reason, the driver should only enjoy / watch the video while the car is in parking mode.
- RESET
After releasing the front panel, use a pencil or any non-metallic object to press & hold the reset button for five
seconds to reset the main unit and the unit will return to the factory default settings.
AV JACK
The panel AV Jack is default as “AV In” source. User can use the Encoder Vol Knob to select “OUT”. Once “OUT” is
selected, the panel AV jack is changed as an AV OUTPUT ( AV OUT ) of the Audio / Video Signal of this unit's Built-in
DVD player.
This AV Out selection is useful for user by simply plug and connect to any external TFT system without any
extra installation.
CAMERA
“OFF” is set as default. If user connected a back up camera system to this unit, user should choose Camera “ON” mode.
Once “ON” is selected, & the vehicle is in Reverse Gear ( Backup mode ), the front in-dash TFT display will automatically
switch to Back Up Camera Video signal regardless whatever mode is currently displayed on the front in-dash TFT.
If connected to a back up camera system but this option is selected to “OFF” mode, User still can press the
mode button to switch “AV In 1” to display the Back Up Camera Video on the front in-dash TFT.
- TO RESET THE DVD SETTING
Press SET UP button on remote control or long press AS/PS button to bring up the SET UP
Menu, select RATING then select DEFAULT, the DVD Setting will resume to factory default
value .
M E N U O P E R AT I O N S
MENU FUNCTION LIST (MENU)
Press & hold the DISPLAY/ MENU button for more than 3 seconds to access into the menu. User can navigate thru the
menu items by pressing the DISPLAY/ MENU button repeatedly, or by pressing the Tuning Up or Tuning Down Buttons
to move to the next or previous menu item. Once the desired menu item appears on the display, user can adjust that
option by using the Encoder Vol Knob within 5 seconds.The menu items can be adjusted as described below:
ANGLE
The panel viewing angle of the display can be adjusted by rotating the encoder vol knob to select the most appropriate
viewing angle.This is useful for user to adjust & obtain the optimum viewing angle inside the vehicle.
CONTRAST
The contrast level of the TFT display is set at "CONTRAST 10" by default. User can use the Encoder Vol Knob to adjust
the contrast level from 00 to 50.
BRIGHT
The brightness level of the TFT display is set at "BRIGHT 20" by default. User can use the Encoder Vol Knob to adjust
the brightness level from 00 to 50.
COLOR
The color level of the TFT display is set at "COLOR 30" by default. User can use the Encoder Vol Knob to adjust the
color level from 00 to 50.
TUNER SET
User can use the Encoder Vol Knob to select between Local or Distance mode.This feature is used to designate the
strength of the signals at which the radio will stop during automatic tuning. "Distance" is the default setting, allowing the
radio to stop at a broader range of signals.To set the unit to select only strong local stations during automatic tuning,
rotate the Encoder Vol Knob button until "Local" appears on the display.
TUNER AREA
User can use the Encoder Vol Knob to select the frequency spacing which is most appropriate for the area this unit is
used in, U.S.A. South America, Europe or Oirt. (Russia Band)
BEEP TONE
The beep tone feature allows the selection of an audible beep tone when a button is pressed. "BEEP TONE On" is the
default setting. Rotate the Encoder Vol Knob to select the "BEEP TONE Off" option
PROGRAMMABLE TURN-ON VOLUME (VOL PGM)
This option allows the adjustment of the volume level of the radio will automatically assume when turning on. "VOL
PGM 12" is the default setting.To program a specific turn on volume level, use the Encoder Vol Knob to select
"VOLUME LEVEL” within 5 seconds.
REAR SPEAKER ON/OFF (REAR SPK)
Rear speaker is set to 'ON' by default. If OFF is selected, the rear speaker's audio output will be TURNED OFF.This
function is useful while listening with the HEADPHONE and user doesn't need Rear Speakers sounds output through
rear speakers. Select “ON” to reactivate the rear speakers sound output
:When the Rear Speaker is 'OFF', the Audio Function, 'FADER', will not be functional
INTER AMPLIFIER ON/OFF(INTER AMP)
This is a option selection for user to turn the unit's built-in Amplifier system on or off. “OFF” is the default setting.This
option is useful for user if connected to an external Amplifier & the user does not want audio output of the built-in
amplifier system.
11
E N G L I S H
D UA L Z O N E O P E R AT I O N
12
“2-ZONE” DUAL A/V ZONE MULTI ENTERTAINMENT OPERATION:
This unit is equipped with the most advanced “Dual A/V Zone” feature.This function is useful if the user would like to select
different modes of the Audio and Video (AV) output source for Front and Rear Speakers and TFT Screens. For example, user
can select to listen to Tuner music for front speakers and rear speaker for DVD movie.And if the user has One or more
TFT screens installed in the rear seat or inside the Car, the Dual A/V Zone function allow the users to enjoy TWO different
Video sources. For example, on the front in-dash Built-In TFT screen can display the video from the Game Console and the
other screen in the rear seat can display video from DVD Movie or other A/V source.The detail operation as follow:
ON/OFF OPERATION
- “Off” is the default setting.
- Long press the “2-Zone” button on the control panel or remote control to switch between Dual Zone On or Off.The
“2-Zone” will appear on the LCD after Dual Zone is selected “on”.
TO SELECT FRONT / REAR AV SOURCES
- Once “ON” is selected, Short Press the “AUDIO” button repeatedly to change between the F-Zone (Front ) and the RZone (Rear) sources.
- If Front Zone “F-Zone” is selected, user have 10 seconds to use the Volume UP / DOWN button to navigate through
different modes:Tuner > DVD > AV - In are available for selection for Front AV Output.
- If Rear Zone “R-Zone” is selected, user have 10 seconds to use the Volume UP / DOWN button to navigate through
different modes:Tuner > DVD > AV - In are available for selection for Rear AV Output
- If no selection is being made within 5 seconds, the unit will resume to the previous mode.
Sub-woofer Low Pass Filter (LPF)
User has 5 seconds to use the encoder volume knob to select the 4 different Low Pass filter Flat, 80Hz, 120Hz or 160Hz.
The Sub-woofer LPF control is only applicable if the unit is equipped with the optional subwoofer line out, and only
if the unit is connected to an optional sub-woofer speaker.
The Sub-woofer LPF option will only appear in the Audio Menu if the “Sub-woofer” function is activated by pressing
the “Sub-w” button on control panel.
X-BASS
User has 5 seconds to use the encoder volume knob to select the 3 different Bass Boost level: Low, Mid, or High.
BASS
BASS LEVEL(Level)
User has 5 seconds to use the encoder volume knob to adjust the desired Bass level range from -6 to +6.
BASS -CFQ (C.Frq).
User has 5 seconds to use the encoder volume knob to adjust the desired Bass Center Frequency to 60Hz, 80Hz, 100Hz,
or 200Hz.
BASS-Q: (BassQ)
User has 5 seconds to use the encoder volume knob to adjust the desired Bass Quality Factor to 2N, 1N, 1W or 2W.
Figure 1 shows the Bass Quality factor (Curve characteristics) of each step.
TO OPERATE FUNCTION OF FRONT / REAR SOURCES
- The Front Panel & Remote control, is defaulted to control the FRONT source's function / operation.
- When DUAL ZONE is turned “ON”, the Mode button is used to change between the Front Source & Rear Source.
Press the mode button repeatedly to change between Front and Rear
- The LCD will display the Rear Source mode for 10 seconds. User has 10 seconds to make the desired operation on the
Rear Source's function on the Front Panel or Remote The LCD will automatically switch back to the Front Source after
10 seconds.And the Front Panel and Remote now is resumed to operate for Front Source's function again.
THE DEFAULT SETTING WHEN DUAL ZONE IS “ON”
- When DUAL ZONE is turned on, the audio output will be muted for about 1 second.
- The default source / mode for Front ZONE is Tuner & for Rear ZONE is “DVD”
- The default Volume level is “12” for both Front & Rear ZONE audio output. (or the Volume Level set as VOL PGM Level
set in the Menu)
- The LCD display is defaulted to display the Front Mode.
- When Dual Zone is “ON”, the audio functions Bass / Treble / Middle / Balance / Fader / Sub-woofer / iX-bass will not be
available.
THE DEFAULT SETTING WHEN DUAL ZONE IS IN “OFF” MODE
- The default audio output reverts to what the user selected for the FRONT Zone source when DUAL ZONE IS “OFF”.
For example:When the DUAL Zone is “ON “, user has selected DVD for Front ZONE & Tuner for Rear ZONE. Once
DUAL ZONE is turned “OFF”,Audio Output for all 4 speakers becomes “DVD” mode.
AU D I O O P E R AT I O N
AUDIO MENU
Short Press “AUDIO“ button to access the Audio Menu. User can navigate thru the Audio Menu items by pressing the /
“AUDIO” button repeatedly, or by pressing the Tuning Up or Tuning Down Button. Once the desired menu item appears on
the display, adjust that option by using the encoder volume knob within 5 seconds.The following menu items can be adjusted
as described above.The unit will automatically exit the Audio Menu after five seconds of inactivity.
SUBWOOFER
Sub-woofer (Level)
User has 5 seconds to use the encoder volume knob to adjust the Sub-woofer lever from '00' to
The Sub-woofer level control is only applicable if the unit is equipped with the optional subwoofer
line out, and only if the unit is connected to an optional sub-woofer speaker.
The Sub-woofer level control option will only appear in the Audio Menu if the “Sub-woofer”
function is activated “ON” by pressing the “Sub-w” button on control panel.
MIDDLE
MIDDLE (LEVEL)
User has 5 seconds to use the encoder volume knob to adjust the desired Middle level range from -6 to +6.
MIDDLE-CFQ (C.FRQ)
User has 5 seconds to use the encoder volume knob to adjust the desired Middle Range Center Frequency to 500Hz,
1KHz, 1.5KHz, or 2.5KHz.
MIDDLE-Q (MID-Q)
User has 5 seconds to use the encoder volume knob to adjust the desired Middle Quality Factor to 2N, 1N, 1W or 2W.
Figure 2 shows the middle Quality factor (Curve characteristics) of each step.
13
E N G L I S H
TREBLE
TREBLE (LEVEL)
User has 5 seconds to use the encoder volume knob to adjust the desired Treble level range from -6 to +6.
TREBLE CFQ (FREQ)
User has 5 seconds to use the encoder volume knob to adjust the desired Treble center frequency to 10KHz, 12.5KHz,
15KHz, or 17.5KHz.
BALANCE
User has 5 seconds to use the encoder volume knob to adjust the Balance between the right and left speakers from
R12 (full right) to L12 (full left). “C00” represents an equal balance between the right and left speakers.
FA D E R
User has 5 seconds to use encoder volume knob to adjust the Fader between the front and rear speakers from R12
(full rear) to F12 (full front). “C00” represents an equal balance between the front and rear speakers.
3. PTY FUNCTION
Pressing PTY(TA) button more than 3 seconds to go into PTY select mode.The user now has 5 seconds to select the
desired PTY item by using encoder volume knob. Once selected the PTY item, user have 5 seconds to press
AUDIO/CENTER” or “TUNE UP (>>)or TUNE DOWN” (<<) buttons < 3 seconds to seek for the selected PTY item.
The LCD will display “PTY SEEK”. If no station with the selected PTY broadcast can be received, the LCD will display
“No Match PTY” for 5 seconds then returns to the previous mode.
User can store his favorite PTY into the preset memory M1 to M6. After selected a PTY item, long press any one of the
preset memory button can store the selected PTY.To recall the stored PTY item switch on PTY mode then press
preset memory < 3 seconds, the unit will automatically search the stored PTY station in the preset memory
T U N E R O P E R AT I O N
14
2.TA FUNCTION
By pressing TA button < 3 seconds, to switch on TA standby mode.The TA icon will light up on the LCD. In the stand by
mode, when a traffic announcement broadcast starts, the traffic announcement broadcast will be received as top priority
regardless of the function mode.When a traffic announcement starts,“TRAFFIC INFO” will show on the LCD, press the TA
button can cancelled the broadcast reception while a traffic announcement broadcast is being received.The unit will go back
to the previous mode and TA goes into stand by mode again.When the TP icon is not light up for 60 seconds.A beep Alarm
tone is heard and the LCD will show “Lost TP,TA”.TA seek will automatic activate and searches to another TA station.
19)BAND BUTTON (BAND)
Press BAND to change between FM bands and AM(MW) bands.
20&21)TUNING UP/DOWN BUTTON (
MANUAL TUNING
Press the Up Tuning(
) or Down Tuning (
up or down by one step.
AUTO SEEK TUNING
Press the Up Tuning (
)or Down Tuning (
/
15
)
)button for more than 3 seconds to move the radio frequency number
)button for less than 3 seconds to move to next station automatically.
12~17)PRESET STATIONS BUTTONS
Six numbered preset buttons store and recall stations for each band.
11)AUTOMATICALLY STORE / PRESET SCAN (AS/PS)
Automatically select 6 strong stations and store them in the current band. Select a band (if needed). Press AS/PS button
for more than three seconds.The new stations replace stations already stored in that band.
PRESET SCAN
Scan stations stored in the current band. Select a band (if needed). Press AS/PS button for less than 3 seconds.The unit will
pause for ten seconds at each preset station. Press AS/PS button again to stop scanning when the desired station is reached.
STEREO
The unit will automatically pick up a stereo signal when available.When in stereo mode, the ST icon appears in the display.
When no stereo signal is available, the unit will automatically revert to mono operation, and no icon will be displayed.
R D S O P E R AT I O N
RDS FUNCTIONS
The unit is equipped with the following RDS function:
- AF Alternative Frequencies
- CT Clock Time
- EON Enchanced other Network
- PI Program identifications
- PS Program service name
- PTY Program Type
- REG Regional Change
- TA Traffic Announcement
- TP Traffic program
1. AF FUNCTION
By pressing AF button < 3 seconds to select AF ON/OFF.‘AF’ icon will light up on the LCD. Under AF “On” mode, if the
tuned in station signal is getting weak, the unit will automatically switches to a different frequency on the same network with
stronger signal.
Factory Default setting is “AF ON”
Factory default stored for PTY preset memory:
M1/News, M2/Information, M3/Pop Music, M4/Sports, M5/Classics, M6/Finance.
C D O P E R AT I O N
AUDIO CD OPERATION - TFT MONITOR
When a Audio CD is inserted into the player and the following picture will appear on the TFT monitor.
E N G L I S H
AUDIO CD OPERATION - REMOTE CONTROL
To operates CD function through the following keys on the remote control.
17.
18.
14.
15.
8~9
19~29
32.
10~13
16.
7.
PAUSE / PLAY BUTTON
STOP
NEXT
BACK
FAST FORWARD & FAST BACKWARD
NUMERIC BUTTONS
REPEAT
UP/DOWN/LEFT/RIGHT BUTTON
OK BUTTON
RANDOM BUTTON
16)OK BUTTON
Use this button to confirm the selection.
7) RANDOM BUTTON
RANDOM button less than 3 seconds is “random play” all songs on the disc.To disable all file “ random play”, press
RANDOM button less than 3 seconds.
AU D I O C D O P E R AT I O N - C O N T RO L PA N E L
The following functions are available operated through the control panel.
12
15
>>I
REL
MODE
II
>
E
ON
M
RD
5
8~9) FAST FORWARD& FAST BACKWARD(
or
)
1. Press FAST FORWARD to fast forward through the disc. Each time the button is pressed,a new speed (2X, 4X, 8X or
20X) is selected.
2. Press PLAY to resume normal playback.
3. Press FAST BACKWARD to fast reverse through the disc. Each time the button is pressed, a new speed (2X, 4X, 8X
or 20X) is selected.
4. Press PLAY to resume normal playback.
The fast forward/backward speed may differ depending upon the disc.
19~29) NUMERIC BUTTONS
1.When playback CD/MP3/WMA use for track number or File number direct access and use when function need
numeric Selection or Input, like in the Goto function,etc.
Y
15) BACK(
)
Press BACK to skip backward to the beginning of the previous chapter.
AS
S
T
RP
14) NEXT(
)
Press NEXT to skip forward to the beginning of the next chapter.
OSD-SET UP
AS-FS
I>>
MUTE
18) STOP( )
1. Press STOP to stop playback and show the logo screen.The player memorizes the location where playback is stopped.
2. Press PLAY to resume playback from the location where playback is stopped (DVD,VCD 1.1,VCD 2.0 and audio CD).
3. Pressing STOP twice is resume playback from the beginning of the disc.
AV IN-OUT
PT
6
IXB
3
AF
STOP
17) PAUSE/ PLAY BUTTON (
/ M1)
1. Press PAUSE to pause playback (still mode).The sound from the disc is muted during still mode.
2. Press PLAY to resume normal playback.
SUBW
2
17
TA
2Z
16
R
4
13
BAND
MCD 775
4x 75W
DISP-MENU
14
TRACK SELECT
Press the TRACK UP (
) or TRACK DOWN (
) button for less than one second to advance to the next track on the
CD,The selected track number will appear on the display. Press and Hold TRACK UP (
) or TRACK DOWN (
)
button for more than one second to fast forward or fast reverse through the disc. CD play starts when the button is
released.
When the last track playback completed, the unit will automatically enter into ‘STOP’ mode. User can press
play button to start the CD playback again when in the ‘STOP’ mode.
12) PAUSE/ PLAY BUTTON (1
)
1. Press PAUSE to pause playback (still mode).The sound from the disc is muted during still mode.
2. Press PLAY to resume normal playback.
13)STOP BUTTON (2 STOP)
1. Press STOP to stop playback and show the logo screen.The player memorizes the location where playback is stopped.
2. Press PLAY to resume playback from the location where playback is stopped (DVD,VCD 1.1,VCD 2.0 and audio CD).
3. Pressing STOP twice is resume playback from the beginning of the disc.
2. Use when playback DVD which need numeric Selection or Input, like in the Goto function,etc
14)REPEAT BUTTON (3 RPT)
Press REPEAT button less than 3 seconds to “repeat play” the current song And keep on repeat Playing the current song
until the “repeat play” is disabled.To disable current song“repeat play”, press REPEAT button less than 3 seconds
32)REPEAT
Press REPEAT button less than 3 seconds to “repeat play” the current song.And keep on repeat Playing the current song
until the “repeat play” is disabled.To disable current song “repeat play”, press REPEAT button less than 3 seconds
15)RANDOM BUTTON (4 RDM)
Press RANDOM button less than 3 seconds is “random play” all songs on the disc.To disable all songs “ random play”,
press RANDOM button less than 3 seconds.
10~13)UP/DOWN/LEFT/RIGHT BUTTON (
Use to move cursor up/down/left/right.
/
/
/
)
MP3/WMA Operation-TFT Monitor
When a MP3/WMA disc is inserted into the player and the following picture will appear on the TFT monitor.
15) BACK(
)
Press BACK to skip backward to the beginning of the previous chapter.
8~9) FAST FORWARD& FAST BACKWARD(
/
)
1. Press FAST FORWARD to fast forward through the disc. Each time the button is pressed, a new speed (2X, 4X, 8X
or 20X) is selected.
2. Press PLAY to resume normal playback.
3. Press FAST BACKWARD to fast reverse through the disc. Each time the button is pressed, a new speed (2X, 4X, 8X
or 20X) is selected.
4. Press PLAY to resume normal playback.
The fast forward/backward speed may differ depending upon the disc.
The player automatically plays the first track.The elapsed time within the track is displayed on the right side of the top
line.When the track is finished, the second track will begin playing, and the track number on the top line will be
updated. Press STOP to stop playback of the current file
17.
18.
14.
15.
8~9
19~29
32.
10~13
16.
7.
PAUSE / PLAY BUTTON
STOP
NEXT
BACK
FAST FORWARD & FAST BACKWARD
NUMERIC BUTTONS
REPEAT
UP/DOWN/LEFT/RIGHT BUTTON
OK BUTTON
RANDOM BUTTON
19~29) NUMERIC BUTTONS
1.When playback CD/MP3/WMA used for track number or File number direct access and used when function need
numeric Selection or Input, like in the Goto function, etc.
2. Use when playback DVD which need numeric Selection or Input, like in the Goto function,etc
32)REPEAT
Press REPEAT button less than 3 seconds to “repeat play” the current file. And keep on repeat Playing the current file
until the “repeat play” is disabled.To disable current file “repeat play”, press REPEAT button less than 3 seconds
10~13)UP/DOWN/LEFT/RIGHT BUTTON (
Use to move cursor up/down/left/right.
/
/
/
)
16)OK BUTTON
Use this button to confirm the selection.
7) RANDOM BUTTON
Press RANDOM button less than 3 seconds is “random play” all files on the disc.To disable all file “ random play”, press
RANDOM button less than 3 seconds.
M P 3 / W M A O P E R AT I O N - C O N T RO L PA N E L
The following functions are available, operated through the control panel.
12
20
15 16
MP3/WMA OPERATION - REMOTE CONTROL
To operates CD function through the following keys on the remote control.
>>I
REL
MODE
E
M
RD
ON
AV IN-OUT
S
T
OSD-SET UP
Y
AS
RP
PT
IXB
6
AF
SUBW
5
3
TA
2Z
2
AS-FS
MUTE
17) PAUSE/ PLAY BUTTON (
/ M1)
1. Press PAUSE to pause playback (still mode).The sound from the disc is muted during still mode.
2. Press PLAY to resume normal playback.
13
18)STOP( )
1. Press STOP to stop playback and show the logo screen.The player memorizes the location where playback is stopped.
2. Press PLAY to resume playback from the location where playback is stopped (DVD,VCD 1.1,VCD 2.0 and audio CD).
3. Pressing STOP twice is resume playback from the beginning of the disc.
R
4
STOP
SELECTING A TRACK TO PLAY
1. Use the UP/DOWN/LEFT/RIGHT direction buttons to move to different file numbers.
2. Press the RIGHT direction button when the highlighted file is in the column on the far right, and up to five more file
in the current directory will be displayed.
3. Press the LEFT direction button when the highlighted file is in the column to the far left, and the previous five file will
be displayed.
4. Press OK on a file number, and that file will begin to play, or by direct numeric input,
5. Enter a file number with the numeric buttons (0-9) and +10 button to play the input Files Number.
>
18
14) NEXT(
)
Press NEXT to skip forward to the beginning of the next chapter.
II
E N G L I S H
M P 3 / W M A O P E R AT I O N
14
I>>
21
BAND
MCD 775
17
4x 75W
DISP-MENU
19
E N G L I S H
20
FILE SELECT
Press the TRACK UP (20) or TRACK DOWN (21) button for less than one second to advance to the next file on the CD,
The selected track number will appear on the display. Press and Hold TRACK UP (20) or TRACK DOWN (21) button for
more than one second to fast forward or fast reverse through the disc. CD play starts when the button is released.
DV D O P E R AT I O N
DVD OPERATION - REMOTE CONTROL
When MP3/WMA is playback, the M5 (16 ) use as RIGHT direction button and M6 (17 ) use as LEFT direction.
This is useful as navigate thru the LEFT page or RIGHT page which the MP3/WMA interface displayed on the
TFT monitor.
When the last file playback completed, the unit will automatically enter into ‘STOP’ mode. User can press play
button to start the DISC playback again when in the ‘STOP’ mode.
12) PAUSE/ PLAY BUTTON (1
)
1. Press PAUSE to pause playback (still mode).The sound from the disc is muted during still mode.
2. Press PLAY to resume normal playback.
13)STOP BUTTON (2 STOP)
1. Press STOP to stop playback and show the logo screen.The player memorizes the location where playback is stopped.
2. Press PLAY to resume playback from the location where playback is stopped (DVD,VCD 1.1,VCD 2.0 and audio CD).
3. Pressing STOP twice is resume playback from the beginning of the disc.
14)REPEAT BUTTON (3 RPT)
Press REPEAT button less than 3 seconds to “repeat play” the current song and keep on repeat Playing the current song
until the “repeat play” is disabled.To disable current song“repeat play”, press REPEAT button less than 3 seconds
15)RANDOM BUTTON (4 RDM)
Press RANDOM button less than 3 seconds is “random play” all songs on the disc.To disable all songs “ random play”,
press RANDOM button less than 3 seconds.
J P E G C D O P E R AT I O N
21
2) EJECT BUTTON ( )
Press the EJECT button to eject the disc or loading the disc.
17)PLAY/PAUSE (
)
1. Press PAUSE to pause playback.
2. Press PAUSE to single step forward to the next picture in the video (DVD and VCD only).
3. Press PLAY to resume normal playback.
18) STOP( )
1. Press STOP to stop playback and show the logo screen.The player memorizes the location where playback is stopped.
2. Press PLAY to resume playback from the location where playback is stopped (DVD,VCD 1.1,VCD 2.0 and audio CD).
3. Pressing STOP twice is resume playback from the beginning of the disc.
8&9) FAST FORWARD& FAST BACK FORWARD(
or
)
1. Press FAST FORWARD to fast forward through the disc. Each time the button is pressed, a new speed (2X, 4X, 8X
or 20X) is selected.
2. Press PLAY to resume normal playback.
3. Press FAST BACKWARD to fast reverse through the disc. Each time the button is pressed, a new speed (2X, 4X, 8X
or 20X) is selected.
4. Press PLAY to resume normal playback.
The fast forward/backward speed may differ depending upon the disc.
LOADING AND DEFAULT PLAYBACK
After inserting the DISC the player searches for and counts the files with appropriate formats (currently only JPG, MP3
and WMA are supported).
OSD will show the message: “Searching for files… .” CD-R media and the number of files found will appear over the
logo background.
When the player has finished searching, it will automatically start Slideshow mode from the first picture; all pictures will
be displayed in their file/folder order. Default Slideshow interval between pictures is five seconds. PAUSE, NEXT, BACK,
and NUMERIC selection and navigation keys work the same as in other operations.
THUMBNAIL VIEW
1. Press the TITLE key to get a thumbnail view. Nine pictures (3x3) will be displayed on the screen, beginning with the last
viewed picture on the upper left part of the screen.The first thumbnail image will be highlighted with a blue border.
2. Use the direction keys (LEFT/RIGHT/UP/DOWN) to select another thumbnail.
3. Use the NEXT/BACK keys to move to another thumbnails page.
4. Use the OK key to switch to the playback mode to start the image last highlighted in the thumbnail view.
14) NEXT(
)
Press NEXT to skip forward to the beginning of the next chapter.
15) BACK(
)
Press BACK to skip backward to the beginning of the previous chapter.
32)REPEAT
Press REPEAT button less than 3 seconds to “repeat play” the current file. And keep on repeat playing the current file
until the “repeat play” is disabled.To disable current file “repeat play”, press REPEAT button less than 3 seconds
10~13) UP/DOWN/LEFT/RIGHT BUTTON
Use these buttons to move cursor up/down/left/right.
16) OK
Use this button to confirm the selection.
E N G L I S H
22
19 ~29) NUMERIC BUTTONS
1.When playback CD/MP3/WMA use for track number or File number direct access and use when function need
numeric Selection or Input, like in the Goto function,etc.
2.When playback DVD use when function need numeric Selection or Input, like in the Goto function,etc
- Select "Title/Chapter" to jump to the beginning of a specific chapter within a specified title (DVD only) and enter the
title and chapter numbers with the number pad and LEFT/RIGHT direction buttons, as follows:
30A) DVD MENU
1. Press DVD MENU to invoke the menu screen included on the DVD disc (DVD only).
2. Press direction buttons to highlight a selected menu entry.
3. Press OK or PLAY to select the highlighted entry. If the highlighted entry indicates a chapter or title, the disc will play
from the selected spot.
- Select "Track" to jump to the beginning of a specific track within a non-DVD disc and enter the track number with the
number pad, as follows:
30B). PBC (PLAY BACK CONTROL) (FOR VCD DISC ONLY)
1. Press DVD MENU to enable/disable PBC functionality with VCD 2.0 discs. PBC must be enabled for menu navigation.
2. Press a number on the number pad to select a track to play(VCD 2.0 only).
3. Press OK to make the selection.
4. Press DVD MENU for the main menu.
33) ZOOM BUTTON
1. Press ZOOM during normal, slow, or still playback.
2. Pressing the ZOOM button repeatedly increases the magnification
level.Three magnification levels are supported. On each press of
ZOOM, the OSD will flash the following:
34)OSD BUTTON
1. Press OSD button once to display the amount of time played and time remaining to be played on the disc. For
example, the OSD may display:
23
2. Press OSD button a second time to additionally display the disc type, current chapter (DVD) or track (VCD, audio
CD), and total number of chapters or tracks. Also displayed (for DVD only) is the current title, total number of titles,
audio language/type/# of channels, subtitle language, and angle selection. For example, the OSD may display:
3. Pressing the direction buttons causes the zoom point to shift, allowing the zoomed image to be panned
1) Some discs may not respond to the zoom feature.
2) Zooming does not work on subtitles or menu screens included on DVDs.
3) The magnification level and number of available levels vary, depending on the TV TYPE selection in the
Setup Menu.
37) TITLE
1. Press TITLE to invoke Title Menu (DVD only, dependent on authoring of disc).
2. Press direction buttons to highlight selected Title Menu entry.
3. Press OK or PLAY to select the highlighted entry. If the highlighted entry indicates a title, that title will play from
Chapter 1.
3. Press OSD button a third time to make the OSD disappear.
36) SUBTITLE
Press SUBTITLE during playback to turn on/off subtitles and to change the subtitles (DVD only).The OSD indicates the
current setting, giving the subtitle track number and the language selected, for example:
Press OSD button in MPEG4 file will display the file name, version, file size and frame rate.
35) GOTO BUTTON
Using GOTO to Jump to a Specific Time, Chapter/Track, or Title 1. Press GOTO to enable the GOTO Menu.The OSD
will display the following:
2. Press the UP/DOWN direction buttons to select the type of search: time search or Chapter/track/title search.
- Select “Time” to jump to a spot on the disc and enter the time in units of hours, minutes, and seconds (hh:mm:ss):
1) The first press will show the current subtitle setting selected; subsequent presses toggle to the next subtitle
setting.
2) Some DVDs display subtitles automatically and cannot be turned Off, even if the subtitle function is set to Off.
3) During some scenes, the subtitles may not appear immediately.
4) Some DVDs allow subtitle selections and turn subtitles on or off only via the disc menu.
5) When a disc is replaced, the Set Up returns to the default setting.
E N G L I S H
38)DVD AUDIO
Press DVD AUDIO during playback to change the audio language when playback a DVD disc.The OSD indicates the
current setting by giving the audio track number, language, audio type, and number of channels. For example:
13.STOP (2 STOP)
1. Press STOP to stop playback and show the logo screen.The player memorizes the location where playback is stopped.
2. Press PLAY to resume playback from the location where playback is stopped (DVD,VCD 1.1,VCD 2.0 and audio CD).
3. Pressing STOP twice is resume playback from the beginning of the disc.
20. NEXT(
)
Press NEXT to skip forward to the beginning of the next chapter.
1) The first press shows the current language selected; subsequent presses toggle The next audio language
2) Some DVDs allow audio selection change only via the disc menu.
3) When a disc replaced, the Set Up returns to the default setting.
39) ANGLE
Press ANGLE while playing a scene recorded with multiple angles to change the angle (DVD only).The OSD indicates the
current angle selected and the total available angles to select, for example:
24
21. BACK(
)
Press BACK to skip backward to the beginning of the previous chapter.
20/21. FAST FORWARD & FAST BACK FORWARD (
or
)
1. Long press FAST FORWARD to fast forward through the disc. Each time the button is pressed, a new speed (2X, 4X,
8X or 20X) is selected.
2. Press PLAY to resume normal playback.
3. Long press FAST BACKWARD to fast reverse through the disc. Each time the button is pressed, a new speed (2X,
4X, 8X or 20X) is selected.
4. Press PLAY to resume normal playback.
14.REPEAT (3 RPT)
Press REPEAT button less than 3 seconds to “repeat play” the current file. And keep on repeat Playing the current file
until the “repeat play” is disabled.To disable current file “repeat play”, press REPEAT button less than 3 seconds
1) The first press will show the current angle selected. Subsequent presses toggle to the next angle.
2) The TFT monitor will light its angle icon when angle changes are available.
3) Some DVDs allow angle changes only via the disc menu.
4) When a disc is replaced, the Set Up returns to the default angle.
DV D O P E R AT I O N - C O N T RO L PA N E L
12
20
15
15. DVD MENU (4 RDM)
Press DVD MENU button less than 3 seconds to invoke the DVD MENU or ROOT on the DVD disc.
Under the DVD MENU or ROOT or TITLE is display on the TFT Monitor.The button of
Track up / down (20 / 21) use as LEFT / RIGHT direction button, Encoder Volume
Knob ( 6 ) as UP / DOWN direction button, and Audio button ( 4 ) as OK button.
17.DVD AUDIO (6 <)
Long press DVD AUDIO button during playback to change the audio language (DVD only).The OSD indicates the
current setting by giving the audio track number, language, audio type, and number of channels. For example:
>>I
REL
MODE
R
AV IN-OUT
IXB
A
OSD-SET UP
Y
>
T
SS
RP
PT
II
SUBW
STOP
5
AF
M
RD
6
E
ON
3
2
TA
2Z
4
AS-FS
I>>
MUTE
13
14
21
BAND
MCD 775
17
4x 75W
DISP-MENU
11
Once a DVD disc is inserted into the unit, the unit will automatically start the playback from the beginning of the disc, and
then the DVD MENU or ROOT or TITLE in the DVD disc will appear on the TFT monitor and “ROOT” will be displayed on
the TFT of the unit.
Under the DVD MENU or ROOT or TITLE is display on the TFT Monitor.The buttons of Track up / down (20 /
21) use as LEFT / RIGHT direction button, Encoder Volume Knob (6) as UP / DOWN direction button, and
Audio (4) as OK button.
12.PLAY/PAUSE (1
)
1. Press PAUSE to pause playback.
2. Press PAUSE to single step forward to the next picture in the video (DVD and VCD only).
3. Press PLAY to resume normal playback.
- The first press shows the current language selected; subsequent presses toggle the next audio language
- Some DVDs allow audio selection change only via the disc menu.
- When a disc replaced, the Set Up returns to the default setting.
11.OSD (AS/PS)
1. Press AS/PS once to display the amount of time played and time remaining to be played on the disc. For example, the
OSD may display:
2. Press AS/PS a second time to additionally display the disc type, current chapter (DVD) or track (VCD/SVCD, audio
CD), and total number of chapters or tracks. Also displayed (for DVD only) is the current title, total number of titles,
audio language/ type/# of channels, subtitle language, and angle selection. For example, the OSD may display:
The AS/PS in MPEG4 file will display the file name, version, file size and frame rate.
25
E N G L I S H
11.SET UP (AS/PS)
While the DVD disc is being played or under stop mode, the “SET UP” (AS/PS) button on the control panel serve the
following function:
Long Press “SET UP” (AS/PS) button to bring up the System Setup Menu
U S B O P E R AT I O N
The unit can support playback MP3 / WMA / JPEG / MPEG4 format which are stored on the
Memory Stick (Max. 1000 tracks). Please read carefully the below instruction before you start the operation of USB
Function.
Please refer to the related description in “system Set Up” for details operation of “Set Up” !
After pressing the “Set Up” button, the LCD will display “Set Up” and keep on blinking. User can use the
following buttons to adjust the “Set Up” items shown on the TFT monitor as follow:
- Encoder Volume Knob as Cursor to navigate thru the Set Up Items shown on the TFT Monitor.
- Track Up / Down ( 20 / 21 ) buttons as Cursor Left / Right to navigate thru the Set Up items shown on the
TFT Monitor.
- AUDIO button as ENTER to confirm the selected item shown on the TFT Monitor
AV IN-OUT
OSD-SET UP
AS-FS
DISP-MENU
Short Press “Set Up” button again or “Play” button to resume the DVD playback .
26
M E M O RY C A R D O P E R AT I O N
The unit can support playback MP3 / WMA / JPEG and MPEG4 format which are stored into SD and MMC Memory
Card (Max 2GB, max 1000 tracks). Pls read below before you start the operation of Memory Card
Mode change to USB HOST
Under any other mode while inserting a USB stick into the USB connector, the unit will automatically switch from
the current mode to USB mode.
Once the unit reads the USB stick successfully, the first audio music file on the USB stick will automatically start
playing. Press the MODE button repeatedly to change to another mode or switch back to USB mode.
Inserting and Removing a SD or MMC card on the main unit
WARNING
Before removing the USB stick from the USB connector. Please always remember to switch off the unit's power or
switch to other mode then remove out the USB Stick. Never try removing the USB Stick while playing music file on
the USB stick. It may damage the USB Stick and sometimes will cause the unit system to lock up.
NOTE
• The unit can support playback Music Player which have USB Interface. However due to the fast changing decoder
technology and different kind of hardware interface, this unit may or may not be compatible to all the Music Player
and USB Stick especially those USB Stick / Player which require to install a program driver.
• About Music Flash Player with USB Interface, usually, the unit takes longer time to read this kind of player than
normal USB Stick. Especially, if the Flash Player with built-in power battery sometimes takes 20-30 seconds to start
up the playback.
• This unit is not compatible with any Portable type of Hard disk.
File Playback Operation
All the USB playback operation function is same as the operation on CD/MP3/WMA. Pls refer
to 'CD/MP3/WMA Operation' for more details.
MODE CHANGE TO MEMORY CARD
After a SD or MMC card was inserted into the main unit card slot Press Mode button to select card mode.The unit will
starts playing the files contained on the Memory Card. Once the unit read the Memory Card successfully, the first file on the
Memory Card will automatically start playback. Press Mode button repeatedly is allowing changing to other modes or switch
back to card mode.
If no any Memory Card is inserted into the main unit card slot. Press mode button will Automatically skip card mode.
FILE PLAYBACK OPERATION
All the SD or MMC Memory Card playback operation function is same as the operation on CD/MP3/WMA. Pls refer to
'CD/MP3/WMA Operation' for more details.
27
E N G L I S H
28
M U LT I - F O R M AT D I S C
S YS T E M S E T U P M E N U
FILTER FUNCTION
The System Menu allows the user to configure the player's behavior to work in harmony with components to which the
player is connected. Press the SET UP on the remote control or Long press “AS/PS” button on the front panel to invoke
the Setup Menu. Pressing the System Menu button during the Setup, Menu will be displayed and the setup menu will be
turned off. Setup menu can be opened during playback.
When the setup Menu is invoked, the OSD will display the following “buttons:”
If a DISC or USB or MEMORY CARD contains various categories of files.This “Filter” function
can hide the files and not allow selection during the File/Folder searching.
1.The selection is done among the 3 categories: a.Audio, b. Photo, c.Video
2. Use right arrow keys to go the “ Filter” field, press “OK” key to open the selection box.
Use up/down keys to navigate through the categories that need to be hidden.
Then press “OK” key to confirm, Use left key to exit the filter function.
M P E G 4 O P E R AT I O N
29
1.The ‘Up/ Down’ buttons can be used to select the category of settings which need to be changed.The page of setting
for that category will be displayed instantly once selected the category.
2.When the category changes are set, press ‘Up/ Down’ repeatedly to return to the text buttons. Selecting the
appropriate button and pressing ‘OK’ can change settings in a different category.
The unit is support playback MPEG4 files , the details operation is exactly the same as CD/MP3/ WMA operation.The
following are special functions pertaining to the playback of MPEG4 File:
LANGUAGE SETTINGS
1. Using the Up/Down buttons, move to the Language button.The player's Language settings
will appear:
EXTERNAL SUBTITLE
External Subtitle setting is used for choosing the language domain, (only for MPEG4). After selecting one language
domain (alphabet), when playback a MPEG4 with external subtitle, the subtitle display will use this language alphabet. If
the displaying subtitle “alphabet” isn’t correct, please make sure to select the correct external subtitle language domain.
2. Use the Right buttons to select the setting.
3. Use the Up/ Down direction buttons to select the setting to be changed.
4. Press Ok to cycle through each possible option or display a list of the available options.
When a list of options appears, press the Up/Down buttons to move among the displayed options.
5. Press Ok again to choose the option and change the setting.
6. Press Ok (after cycling through the options) to change the displayed value of the next
available option and change the setting.
The following language domains are available:
Turkish
= Albanian, Danish, Dutch, English, Finnish, French, Gaelic, German, Italian, Kurdish (Latin),
Norwegian, Portuguese, Spanish, Swedish and Turkish.
Central_European
=Albanian, Croat, Czech, Dutch, English, German, Hungarian,Irish, Polish, Romanian, Slovak,
Slovene and Sorbian.
Cyrillic
=Bulgarian, Belorussian, English, Macedonian, Moldavian, Russian, Serbian and Ukrainian.
Western European
=Albanian, Breton, Catalan, Danish, Dutch, English, Faroese, Finnish, French, Gaelic, German,
Icelandic, Irish, Italian, Norwegian, Portuguese, Spanish and Swedish.
The MPEG4 Subtitle selection appears in the ‘SET UP” menu > language > MPEG4 subtitle
E N G L I S H
30
OSD Language
Selecting the OSD setting allows the user to select a preferred language for the OSD menu
and messages.The following options are available:
The following subsections explain the available options for each of the Video settings.
TV Aspect Ratio
Selecting the TV Aspect setting allows the user to select the aspect ratio of the TV (DVD and
VCD only).The following options are available:
4:3 = Aspect ratio of TV is 4:3.
16:9 = Aspect ratio of TV is 16:9. Both widescreen and 4:3 contents will fill
the entire screen.
Most widescreen DVDs will not allow pan & scan conversion. If 4:3 PS is
selected on these DVDs, letterboxing will be used instead.
If 16:9 is selected and a 4:3 TV is connected, 16:9 content will appear distorted
during playback (objects look thin).
TV System (NTSC or PAL)
The Video setting allows the user to select the TV standard (DVD and VCD/SVCD only).The
following options are available:
English = Menu/OSD is in English (factory default)
Français = Menu/OSD is in French
Español = Menu/OSD is in Spanish
Deutsch = Menu/OSD is in German
Italiano = Menu/OSD is in Italian
Portugués = Menu/OSD is in Portuguese
Turkçe = Menu/OSD is in Turkish
Russian = Menu/OSD is in Russian
31
Some DVDs may not include the pre-selected language. In this case, the unit will automatically display menus in
the disc’s initial language setting.
VIDEO SETTINGS
1. Using the Up/Down buttons, move to the Video.The Player's Video settings will appear:
NTSC
PAL
AUTO
= TV is NTSC. PAL content is played at NTSC resolution and frame
rate (factory default).
= TV is PAL. NTSC content is played at PAL resolution and frame rate.
= If the content is PAL, the output is PAL. If the content is NTSC, the
output is NTSC.
Playing PAL DVDs with TV SYS set to NTSC is not allowed.
The OSD will indicate:(OSD) PAL to NTSC error.
RATING SETTINGS
1. Using the Up/Down buttons, move to “Rating”, the Rating settings will appear:
2. Use the Right buttons to select the setting.
3. Use the Up/Down buttons to select the setting to be changed.
4. Press Ok to cycle through each possible option or display a list of the options.When a list
of options appears, press the Up/Down buttons to move among the displayed options.
5. Press Ok again to choose the option and change the setting.
6.Press Ok (after cycling through the options) to change the displayed value of the next
available opions and change the setting.
2. Use the Right buttons to select the setting.
3. Use the Up/Down buttons to select the setting to be changed.
The following subsections explain how to change each of the player's Rating settings.
E N G L I S H
32
Parental Control Rating Selection
The Rating allows the user to have parental control feature of the player. Press the “OK” button the below window will
appear on the screen, to allow user to enter the password, will pop up a window let user set password:
If incorrect password is entered, the below “Incorrect Password” window will appear.
The factory default password is 8888
Parental control functions only available if the DVD title is encoded in its program.
Parental control does not work for VCD/SVCD/CVD or CD audio.
Set password setting
User can set new password in the Set password setting. Go to “set”, press Ok to pop up the “Enter Password” window,
enter the old password. Press Ok twice, then the “Enter New Password” window will pop up, Enter the new password,
press Ok to confirm.
Once entered the correct password, press “OK” the “correct password” message will appear.
33
MISC
1. Using the Up/Down buttons, move to the Misc. the Misc Rating settings will appear:
Press Ok to to cycle through the available options.The following options are available:
2. Use the Right buttons to select the setting.
3. Use the Up/Down buttons to select the setting to be changed.
4.Press Ok for each setting to cycle through the options and change the settings.
The following subsections will explain the available options for each of the Misc settings.
Use Default Settings
Press Ok, pop up window “ Use Default Setting”, there are two selections:Yes/No.
No = Close Setup menu
Yes = Return to Use Default Setting
Kid Safe
G
PG
PG-13
PG-R
R
NC-17
Adult
= Only titles with a parental control setting
= Only titles with a parental control setting
= Only titles with a parental control setting
= Only titles with a parental control setting
= Only titles with a parental control setting
= Only titles with a parental control setting
= Only titles with a parental control setting
= Allow any title to play (factory default).
of 1 are allowed to play
of 2 or less are allowed to play
of 3 or less are allowed to play
of 4 or less are allowed to Play
of 5 or less are allowed to play
of 6 or less are allowed to play
of 7 or less are allowed to play
E N G L I S H
34
S P E C I F I C AT I O N
T RO U B L E S H O OT I N G
TFT SCREEN SECTION
Screen Size: 3.5"(Measured Diagonally)
Screen Type:TFT Liquid Crystal Display active matrix
Resolution: 960 (W) x 324 (H)
Before going through the check list, check wiring connection. If any of the problems persist
after check list has been made, consult your nearest service dealer.
DVD / CD SECTION
Compatible Disc/Format
Signal to Noise Ratio
Dynamic Range
Frequency Response
See “ Disc Note” for more details description
> 90 dB
> 90 dB
20Hz to 20Khz +/-3dB
VIDEO SECTION
Color System
Video Output
Video Input
NTSC / PAL
Composite 1.0 Vp-p (+/- 0.2) 75 - ohm
Composite 1.0 Vp-p (+/- 0.2) 75 - ohm
AUDIO SECTION
Line out level
Line out Impedance
2 Volt
200 ohm
AUXILIARY INPUT SECTION
Input Maximum Voltage
Input Impedance
1200 mV
4.7k ohm
GENERAL
Fuse
Operating Temperature
15-Amp Mini ATM Type
0-C to 50-C
Unit Mounting Angle
< 30
o
35