Rock-Ola Wall-Rock-PV™ Installation Instructions

Installation Instructions
Rock-Ola® Wall-Rock-PV™
Credit Card Reader Kit #26677521
This kit contains the parts and instruction to install a swipe card reader to your Rock-Ola WallRock-PV.
Tools Required
#2 Phillips Head Screwdriver
5/16 nut driver
Parts Included with this Kit
Item #
1
2
3
4
5
6
7
Part Number
40970701
40970601
22185303
28277902
87842300
22000215
22207602
Description
Quantity
Bracket - Base Credit Card Reader
1
Bracket - Mounting Credit Card Reader
1
Card Reader - Swipe
1
Screw - M3 x 10 PPAN
2
Nut, KEPS #6-32 HEX
2
These Instructions
1
Label - Credit Card Reader
1
Instructions
Note: If you are installing this kit along with the AMI Conversion Kit, skip ahead to step 4.
1. Turn the jukebox power OFF, unplug the Power Cord from the wall, and open the
jukebox door.
2. The Credit Card Reader will be installed at this location. See Figure 1.
Location of the Credit
Card Reader
Credit Card Reader
Blockout Plate
Figure 1
Page 1 of 6
22000215
REV. B
3. Remove the Credit Card Reader Blockout Plate and the Credit Card Reader Blockout
Bracket. See Figure 2
Note: You may want to remove the Coin Box and the Mars Bill Box for easier installation.
A. Remove the two nuts from the Credit Card Reader Blockout Plate, and remove it.
B. Remove the two screws from the Credit Card Reader Blockout Bracket (Keep the
screws). See Figure 2.
Mars Bill Box
remove
Remove
screws
screws
Remove
remove
nuts
Credit Card Reader
Blockout Bracket
Coin
Box
Figure 2
4. Fasten the Swipe Card Reader (Item #3) to the Credit Card Reader Mounting Bracket
using the two M3 x 10 Pan Head Screws (Item #4). See Figure 3.
Note: Orient the Swipe Card Reader so the USB Cable feeds through the cutout on the
Credit Card Reader Mounting Bracket (Item #2). See Figure 3.
USB cord
Credit Card Reader
Mounting Bracket
Swipe Card
Reader
Install
install two
screws
Figure 3
Page 2 of 6
22000215
REV. B
5. Install the Credit Card Reader Label (Item #7).
A. Install the Credit Card Reader Label over the existing Rock-Ola Credit Card
Reader Label as shown in Figure 4 and Figure 5.
Rock-Ola
Credit Card
Reader Label
New Credit
Card Reader
Label
Figure 4
Figure 5
6. Install the Base Credit Card Reader Bracket (Item #1) to the two Bosses on the Door
(See Figure 6), using the two screws that were removed in step 3B of this manual. See
Figure 7.
Note: The rectangular cutout on the bracket must be toward the top of the Door.
Rectangular
Cutout
Base Credit
Card Reader
Bracket
Mounting
mounting
Bosses
bosses on
on
door
door
Figure 6
Install two
Install two
screws
screws
Figure 7
Page 3 of 6
22000215
REV. B
7. Install the Credit Card Reader Mounting Bracket with the Swipe Card Reader
attached.
A. From the outside of the Door, feed the USB Cable from the Swipe Card Reader,
through the rectangular cutout on the Base Credit Card Reader Bracket. See
Figure 8.
B. Push the two studs on the Credit Card Reader Mounting Bracket through the two
holes on the Base Credit Card Reader Bracket. See Figure 8.
C. Fasten the brackets together using the two 6-32 HEX Nuts (Item #5). See
Figure 8.
D. The Swipe Card Reader is now installed. See Figure 9.
Install two 8-32
hex nutshex nuts
USB Cord
Figure 8
Figure 9
Note: If you removed the Coin Box and Mars Bill Box, re-install them at this time.
Page 4 of 6
22000215
REV. B
8. Route the USB Cable from the Door into the Cabinet through the Cable Clamps and
over to the Rowe CPU Assembly. Plug the USB Cable into the USB Jack closest to
the rear of the Cabinet (You may need to temporarily remove the Ethernet cable to
make the installation easier). See Figure 10.
USB Cord plugged into the
USB jack closest to the back
wall
Ethernet
Cable
Rowe CPU
Assembly
Figure 10
9. Power Up and Operational Check
Note: The jukebox must have software Version V2.3.0 or higher and have a Broadband
connection to the server for credit card acceptance to function.
Power ON the jukebox and wait for the User Interface (Selection Screen) to come up.
Swipe a valid credit card through the Card Reader. If the Card Reader is connected
properly, the jukebox screen will display a pop-up window as shown here.
Figure 11
Touch the Cancel Button to close the window and cancel the credit transaction.
10. Change the Attract Loop to Highlight Credit Card Acceptance
Enter the Service Mode by pushing service on the Rowelink Controller. Touch
“Location/System Setup” then touch “Attract Mode”. Touch “Default Loop with
Credit Card” from the list to select it.
Page 5 of 6
22000215
REV. B
Page 6 of 6
22000215
REV. B