kvm repeater - AV-iQ

REAR VIEW
Specifications
KVM
REPEATER
Function
RJ-45 Connector
Power
Link
LEDs
(From Local)
Link
(To Remote)
Video Resolution
Cable Distance
Power Adapter
Housing
Weight
Dimensions(LxWxH)
KVM-S1
2
1
1
1
1
2048×1536@60HZ
300 m (Max.)
DC 9V 600mA
Aluminum
235 g
130x83.5x29.5 mm
No
1
Component
Power Jack
Description
The power adaptor plugs here.
Installation
KVM-S1
Front View
Rear View
Hardware Requirements
Required specifications
1 x Highest resolution monitor.
Console 1 x PS/2 mouse.
1 x PS/2 keyboard.
1 x VGA, SVGA or Multisync card.
1 x 6-pin mini-DIN (PS/2) mouse port.
PC
1 x 6-pin mini-DIN (PS/2) keyboard port.
Cable 1 x 3-in-1 KVM cable or equivalent.
KVM-S1
USER MANUAL
FRONT VIEW
V1.1
1
Package Contents
z
KVM Repeater
x1
z
User manual
x1
z
Power adapter DC 9V/600mA x 1
If any thing missed, please contact with your vendor.
No
2
4
Component
1
CAT.5
Connector
2
Link LED
Features
3
Power LED
ƒ Provide KVM Extender extra transmission distance up
to 300 meter.
ƒ High VGA resolution up to 2048x1536.
4
Link LED
5
CAT.5
Connector
-1-
3
5
DC 9V
600mA
Adaptor
from
to
KVM-R-PRO
(Remote)
1. Power on KVM-S1.
2. Connect CAT5 cable to Local.
3. Check the LED status of “From Local”, on is link ok, off
is link fail.
4. Connect CAT5 cable to Remote.
5. Check the LED status of “To Remote”, on is link ok, off
is link fail.
Description
Plugs the CAT5 cable into this
connector from Local.
On: Local and KVM-S1 links ok.
Off: Local and KVM-S1 links fail.
Flash: when local user is using.
On: power on.
Off: power off.
On: Remote and KVM-S1 links ok.
Off: Remote and KVM-S1 links fail.
Flash: when remote user is using.
Plugs the CAT5 cable into this
connector to Remote.
-2-
KVM-L-PRO
(Local)
-3-
Operation
Configure Video quality on Remote Unit
If the length of cables is different just like below, the
Remote user can press ← or → keys after press “E” key
in command mode to adjust the value of video
equalization more precisely for better video quality.
KVM-R-PRO
(Remote)
KVM-S1
CAT5/E
( 300m)
CAT5/E
(50m)
Remote
User
PC
KVM-S1 is designed to be passive unit of KVM-Extender
to enlarge the transmission, so it doesn’t provide any
control interface directly. The user can use Remote unit to
adjustment all system’s video quality.
First, the remote user need to press hot key (default:
Scroll Lock) twice to enter the command mode, then
press “a” key to process automatic video adjustment and
setting the whole system.
After first automatic video adjustment, the remote user
can enter “command mode” and press below key to
select video adjustment function.
Local
User
KVM-L-PRO
(Local)
Troubleshooting
1. If the Power LED of Remote is not on, please make
sure power adapter is connected.
2. If no video signal is displayed on the monitor.
(1) Please check CAT5 cable is loosened or
disconnected.
(2) Power adapter is not connected.
3. If video signal is foggy or un-clear, please check VGA
connector, or low the VGA resolution for long cable.
Then press ↑ or ↓ key to adjust the value. When finished,
press “ESC” key to end adjust.
Key
A
N
E
R
G
B
D
Function
Adjust video quality Automatically
Adjust video Gain
Adjust video Equalization
Adjust Red skew time
Adjust Green skew time
Adjust Blue skew time
Set video and hot key to Default
NOTE: All the video parameters have 32 levels to adjust.
You can also press & hold ↑ or ↓ to continually adjust
video, and if you adjust it to the last level then there will
be a “long” beep sound.
-4-
© C&C TECHNIC TAIWAN CO., LTD. All rights reserved.
Trademarks:
All the companies, brand names, and product names
referred to this manual are the trademarks or registered
trademarks belonging to their respective companies.
-5-