Turntable

Turntable
Cher Client,
Merci d’avoir choisi la platine Elipson.
Prenez le temps de lire attentivement ce mode d’emploi avant d’installer votre platine.
Il contient des conseils pour en tirer le meilleur profit et des instructions pour l’utiliser sans risque.
Nous vous recommandons vivement de conserver l’emballage et ce mode d’emploi
pour d’éventuels usages ultérieurs.
MODÈLES :
UK
WARNING
YOUR TURNTABLE IS NOT READY
FOR IMMEDIATE USE.
YOU MUST FOLLOW THESE INSTRUCTIONS
OF INSTALLATION BEFORE ANY USE.
12
I. UNPACKING
Place the cardboard
in a clear and
unobstructed area.
Identify the direction of
the opening of the box.
Open the box carefully
and remove the
protective foam.
Remove the lid of the carton, take out the turntable
and place it on a flat and clear surface.
II. CONTENT
Before use, confirm that the following items are included :
Turntable
RCA cable
User manual
Belt
Power source
adaptator
Felt
13
Centralizer
UK
III. DESCRIPTION
2
3
1
6
4
5
1. Lid
2. Pulley
3. Belt
4. Tonearm
5. Plate
6. Chassis
14
8
9
7
13
7. 33 rpm / off / 45 rpm Switch
8. Felt
9. Anti-skating trackwheel
10. Counterweight
11. Tonearm support
12. Cartridge-holder
13. Cartridge
15
12
UK
IV. SET UP
1. PREPARATION
During transport, the removable lid and the various elements of the turntable are stranded
by wedges.
• Position the lid above the plate, and adjust the two hinges in the appropriate spaces.
Carefully check the orientation of the hinges and the proper fit of the lid on the plate. Press
firmly to ensure good holding of the lid.
• Carefully remove the protective foams of the plate (x2), the tonearm (x2), and the motor
pulley (x1). Then gently remove the foam wedge located under the pulley.
• Setting up the belt :
- with the left hand, gently hold the belt in the slot of the pulley
- with the right hand, tension the belt from the pulley to the plate avoiding stretching
- carefully wrap the belt around the plate avoiding folds.
Check out our video tutorial on Youtube : https://youtu.be/PtjOU4I1WAU
16
• Place the felt on the plate.
• Check the level of evenness of the plate, adjust it using the adjustable feet if necessary.
2. COUNTERWEIGHT SETTING
YOUR ELIPSON TURNTABLE WAS SET IN FACTORY TO ENSURE OPTIMUM UTILIZATION.
THESE ADJUSTMENTS ARE FOR ADVISED USERS ONLY.
The counterweight balances the tonearm depending on the weight of the cartridge. Each
cartridge model having a different weight, you should set the weight accordingly.
In case of disruption, or if you changed the cartridge, it may be necessary to reset the
counterweight again.
• Cut out the paper template on page 23 of this user manual, then put the counterweight on
high stop and adjust the weight according to the template, depending on the cartridge used.
9,5 mm
7,5 mm
17
UK
3. OPTIONAL SET UP
YOUR ELIPSON TURNTABLE WAS SET IN FACTORY TO ENSURE OPTIMUM UTILIZATION.
THESE ADJUSTMENTS ARE FOR ADVISED USERS ONLY.
Anti-skating
When the turntable is operating, the friction of the diamond in the vinyl furrow creates a force
that pulls the tonearm towards the center of the turntable. The anti-skating compensates this
attraction to reduce the distorsion it generates. Ideally, the set up of the anti-skating is done
on a blank disc (not provided). The force of the anti-skating can be manually adjusted by the
trackwheel on the tonearm. When the cartridge is placed on the disc, it should not move,
either inwards or outwards the disc.
• Switch on the turntable.
• Place the cartridge in the middle of the blank disc.
• If the cartridge moves inside the vinyl, the anti-skating is too low :
you must increase the force by turning the trackwheel counterclockwise.
• If the cartridge moves outside the vinyl, the anti-skating is too strong :
you must decrease the force by turning the trackwheel clockwise.
Orientation of the cartridge
In case of change of the cartridge, or if the turntable has been moved, it may be necessary to
adjust the orientation of the cartridge. The cartridge holder includes two screws to adjust the
angle of the cartridge according to the type of vinyl (33 rpm or 45 rpm).
18
4. ANALOG CONNECTION
Requires Hi-Fi amplifier with phono input or external RIAA module.
• Connect the turntable to the phono input of the amplifier using the provided RCA cable
respecting the polarity
(right) and
(left).
• Connect the ground wire in the input
shown on the turntable and the amplifier.
ALL THE SET UP OPERATIONS OF YOUR TURNTABLE ARE DONE.
YOU CAN NOW LISTEN TO YOUR FIRST VINYL DISC
ON ELIPSON’S TURNTABLE.
FOR THE RUNNING-IN PHASE OF YOUR HI-FI DEVICES,
ELIPSON DEVELOPED A DISC SUITABLE TO YOUR SYSTEM.
CONTACT US FOR MORE INFORMATIONS.
IF IN DOUBT, PLEASE CONTACT AN ELIPSON PROFESSIONAL.
19
UK
SPECIFICATIONS
Crosstalk >60dB
Dimensions (W x H x D) : 450 x 120 x 380 mm
Net weight : Alpha : 5 kg
Omega : 5,8 kg
WARNING
Packaging
The packaging (box and packing) was designed for effective protection of your ELIPSON
electronics during transportation and shipping. Please save them for later use. Protect
the environment : if you wish to dispose of the packaging, please do so in the most
environmentally responsible manner possible according to available measures (for example,
sorted recycling). At the end of its life, this device should not be disposed of the same way as
household refuse. It should be returned to a center for the recycling of electronic equipment.
This symbol on the product indicates that it has been designed so that it can
be recycled according to specific procedures. You will therefore be making a
significant contribution to the protection of the environment. This device respects
the RoHS European directive. This means that it does not emit polluting substances
when it is recycled (such as lead, mercury, cadmium, hexavalent chromium,
polybromobiphenyles, polybromdiphenylethers).
Precautions for proper use
This product was designed according to rigorous norms and complies with safety standards.
It should only be used under normal conditions as described below. Verify the electrical
voltage before connecting it to a power source. This electronic device was designed to
work in numerous countries. We advise you to hook it up completely before connecting it to
the AC power source. Take care when unplugging the power cord. When you unplug the
power cord from the power source, do so by pulling on the head of the plug rather than on
the cable. If you do not expect to use this device for a prolonged period
of time, you are advised to unplug it from the power source. Do not open
the case. This device contains no parts that can be exchanged by the
user. Accessing the inside of this device’s case can lead to electric shock.
Any modification to the product will nullify the guarantee. If a foreign
object or liquid falls into the case, contact your retailer to arrange for a
technician to remove it from the device safely.
WARRANTY
Elipson turntable has been designed and manufactured to the highest quality standards.
If something goes wrong with your product, Elipson or its authorized distributor / dealer will
handle the service and repair under these limited warranty terms. This limited warranty is
valid for a 2-year period from original purchase date from an authorized Elipson dealer.
Terms of limited warranty
The warranty is limited to equipment repair. Neither transportation, nor any other costs, nor
any risk for removal, transportation and installation of products is covered by this warranty.
The warranty is only valid for the original purchaser and is not transferable. The warranty
will not apply in cases other than defects in materials and / or workmanship at the date of
purchase and will not be applicable in the following cases :
- Damages caused by wrong or incorrect installation or connection.
- Damages caused by incorrect use, other use than the one described in the owner’s
20
manual, negligence, unauthorized modification or use of parts or of accessories that are
not authorized by Elipson.
- Damages caused by unauthorized, unsuitable or faulty ancillary equipment.
- Damages caused by accidents, lightning, water, fire, heat or any other disturbance that
would not be under Elipson control or responsibility.
- For products, which serial number has been altered, deleted, removed or made illegible.
- In case of repair and service executed by an unauthorized service person.
This warranty complements any national/federal/regional law obligations of local
distributors/dealers and does not affect your statutory rights as a customer.
To claim repair under warranty
To claim repair or service under warranty you simply have to contact your local Elipson
dealer, from whom your equipment has been purchased. To ensure that you will be able to
ship your damaged product in correct manner, always retain the original packaging of your
Elipson equipment. If you cannot contact your original dealer, or if you are using your Elipson
product outside the purchase country, you should contact Elipson national distributor in the
residence country, who will advise where the equipment can be serviced.
You can also visit our web site to check our contact information :
www.elipson.com
To validate your warranty, you need to produce, as a proof of purchase, your original
purchase invoice specifying the date of purchase and stamped by your dealer.
© Elipson 2015
Elipson is a registered trademark of AV Industry.
21
DÉCOUPEZ CI-CONTRE LE GABARIT DE RÉGLAGE
DU CONTRE-POIDS
CUT OUT THE SETTING TEMPLATE
OF THE COUNTERWEIGHT
22
23
9,5mm
7,5mm
OM10
OM10
09/05/2016
www.elipson.com