Sapper Monitor Arm Collection Double Monitor Arm Kit (Standard

Sapper Monitor Arm Collection
Double Monitor Arm Kit
(Standard and Sapper 50 Arms)
Installation Instructions
10/22/2014
ii_front_2_d
SMA-DK
Step 1: Attach Mount to Work Surface, Slat wall or Wall
Two-Piece Table Clamp,
Heavy Duty Table Clamp and
Deep Table Clamp Mounts
Tools Needed
Allen wrenches (in inches)
• Clamp lower to upper jaw – 5/32” (B)
• Clamp to mast – 5/16” (H)
• Clamp compression screws – 1/4” (A)
For installation on a work surface positioned
against a wall or panel:
For installation on open edge of work surface:
1. Remove clamp lower jaw (C), by removing both clamping
screws (A) and both lower jaw mounting screws (B).
1. Assemble mast (E) to clamp (G), by inserting the pin (F) on
clamp (G) into hole in bottom of mast (E). Secure mast
(E), to clamp (G), with screw (H). Tighten securely.
2. Assemble mast (E) to clamp upper jaw (G), by inserting the
pin (F) on clamp (G) into hole in bottom of mast (E). Secure
mast (E), to clamp (G), with screw (H). Tighten securely.
Slide upper jaw (G) down along edge of desk surface.
3. Beneath work surface, replace lower jaw (C), by reinstalling
(2) mounting screws (B), (2) clamping screws (A) and (2)
pressure discs (D). Tighten both clamping screws (A) with
pressure discs (D) in place on top of clamping screws (A).
Remove Lower Jaw
Do not over-tighten as this may damage the table surface.
2. Slide table clamp (G) onto edge of desk surface. With
pressure discs (D) in place on top of clamping screws
(A), tighten both clamp screws (A). Do not over-tighten
as this may damage the table surface. If clamp
opening needs adjustment to accommodate thicker
or thinner desk top, follow instructions to the left.
Note: T
he Deep Table Clamp (Fig. 1) is one piece and can only be
mounted on open edge of worksurface as described above .
D
G
Deep Table Clamp
B
Fig. 1
C
A
Deep and Heavy Duty Table Clamp Mounts
sapclmpdp
E
E
F
F
G
Two-Piece and Heavy Duty
Table Clamps
G
work surface
E
work surface
G
D
A
H
H
Mast to Clamp
2
Mast to Clamp
Clamp to Work Surface
Clamp to Work Surface
Clamp, Edge Mounting
Grommet Mount
Fixed Table Mount
Tools Needed
Tools Needed
• 3/4” open end wrench (C)
• 3/4” open end wrench (C)
• Drill
1. Choose the orientation of grommet mount plate (A) on the
work surface. Remove grommet cover and any moveable
grommet liner.
1. Establish desired mounting location. Drill a 17/32” diameter
hole, through the table surface/desk top. Assemble
disc (A), lock washer (B) and nut (C), onto stud (D).
2. Place the grommet mount plate (A) over the grommet hole, with
½” hole for the threaded connection stud (F) inside the
grommet hole. Adjust placement of the grommet mount plate
(A) so it equally overhangs the grommet hole.
2. From beneath the desk, push top of stud (D), up through
hole. Slide second disc (A) over stud (D). Thread mast
(E) onto stud using all available threads in mast (E).
3. Thread the threaded connection stud (F) into the bottom of the
mast (E) using all available threads. Pass the threaded
connection stud (F) though the ½” hole in grommet mount plate
(A) and through the grommet hole.
3. Orient the mast (E), with the top of the slope facing
the user (see illustration). Tighten nut (C). Do not overtighten as this may damage the table surface.
4. Beneath the desk, slide the mounting bar (B) and washer (D)
onto the threaded connection stud (F). Thread nut (C) onto
threaded connection stud (F). Orient the mast with the top of
the slope (H) facing the user. Tighten nut (C) using a wrench.
Do not over-tighten as this may damage the table surface.
H
F
E
E
A
A
work surface
B
F
work surface
D
A
B
D
C
Grommet Mount
ii_grommet.eps
C
Fixed Table Mount
3
Step 1: Attach Mount to Work Surface, Slat wall or Wall
Crinion Open Table Center Channel Mount
Dividends Horizon Benching Mount
Tools Needed
Tools Needed
Allen Wrenches (in inches and mm’s)
Allen wrenches (in inches)
• C
rinion Open Table (COT) Center Channel Mount to
Mast – 5/16” (E)
• Mount to mast - 5/16” (H)
• Compression Screws - 1/4” (A)
• C
rinion Open Table (COT) Center Channel Mount to
Flex-Link Nuts – (5mm) (C)
1. Assemble mast (D) to COT Center Channel Mount (B), by
inserting the pin (F) on the COT Center Channel Mount (B) into
the hole in the bottom of the mast (D). Secure mast (D) to COT
Center Channel Mount (B) with screw (E). Tighten securely.
2. Insert (2) flex-link nuts (A) into top center channel of COT by
pushing one side (long edge) down into the channel until the
following edge/side drops into the channel.
3. Slide flex-link nuts (A) to desired mounting location. Assemble
COT Center Channel Mount (B) to flex-link nuts (A) with screws
(C), tighten securely.
1. Remove both Dividends Horizon Benching Mount lower jaws
(C), by removing both clamping screws (A) and both lower jaw
mounting screws (B).
2. Assemble mast (E) to Dividends Horizon Benching Mount (G),
by inserting the pin (F) on Dividends Horizon Benching Mount
(G) into hole in bottom of mast (E). Secure mast (E), to
Dividends Horizon Benching Mount (G), with screw (H). Tighten
securely. Slide Dividends Horizon Benching Mount (G) down
along edge of desk surface.
3. Beneath work surface, replace both lower jaws (C), by
reinstalling (2) mounting screws (B), (2) clamping screws (A) and
(2) pressure discs (D). Tighten both clamping screws (A) with
pressure discs (D) in place on top of clamping screws (A). Do
not over-tighten as this may damage the table surface.
E
A
D
F
D
G
C
C
F
H
B
C
B
E
A
A
4
Crinion Open Table Center Channel Mount
Antenna Table Center Beam Center Mount
Antenna Table Center Beam Side Mount
Tools Needed
Tools Needed
Allen wrenches (in inches and mm’s)
Allen wrenches (in inches and mm’s)
• Antenna Table Center Beam Center Mount to Mast – 5/16” (E)
• Antenna Table Center Beam Side Mount to Mast – 1/4” (E)
• A
ntenna Table Center Beam Center Mount to
Flex-Link Nuts – (5mm) (C)
• A
ntenna Table Center Beam Side Mount to
Flex-Link Nuts – Phillips Screwdriver (C)
1. Assemble mast (D) to Antenna Table Center Beam Center
Mount (B), by inserting the pin (F) on the Antenna Table Center
Beam Mount (B) into the hole in the bottom of the mast (D).
Secure mast (D) to Antenna Table Center Beam Center Mount
(B) with screw (E). Tighten securely.
1.Assemble mast (D) to Antenna Table Center Beam Side Mount
(B), by inserting the curved ribs (F) of Center Beam Side Mount
(B) into voids of mast (D). Secure mast to Antenna Table
Center Beam Side Mount (B) with screw (E). Tighten securely.
2. Insert (2) flex-link nuts (A) into top center beam of Antenna Big
Table by pushing one side (long edge) down into the beam until
the following edge/side drops into the channel.
3. Slide flex-link nuts (A) to desired mounting location. Assemble
Antenna Table Center Beam Center Mount (B) to flex-link nuts
(A) with screws (C), tighten securely.
2.Insert (2) flex-link nuts (A) into side channel of beam of Antenna
Big Table by pushing one side (long edge) down into the
channel until the following edge/side drops into the channel.
3.Slide flex-link nuts (A) to desired mounting location. Assemble
Antenna Table Center Beam Side Mount (B) by dropping
bracket on side flange of beam (G) and securing with screws
(C). Tighten securely.
D
D
C
G
A
F
F
B
B
A
C
E
E
A
A
5
Antenna Table Side Beam Mount
Slat Wall Mast Mount
Wall Mast Mount
(for Architectural Walls Only)
Tools Needed
Tools Needed
Allen wrenches (in inches)
Allen wrenches (in inches)
• Slat wall Mounted Mast Bracket to Mast - 5/16” (K)
• Wall Mounted Mast Bracket to Mast - 5/16” (K)
• Slat wall to strap – 5/32” (C)
• Wall anti-dislodgement – 1/16” (G)
• Slat wall anti-dislodgement – 1/16” (G)
1. Insert the mounting strap (A) into desired slatwall slot, with
holes closer to top edge. Hang slat wall bracket (B), in desired
slot aligning strap (A) holes with appropriate hole in bracket (B).
2. Install and tighten (2) screws (C). Hang mast mount
bracket (D) on slat wall bracket (B), by engaging hanger
strap (E) with top hook of hanger casting (F). Seat mast
mount bracket (D) down, fully onto hanger casting (F).
1. Mark the locations for four mounting screws customer
supplied (A) on the wall at the desired location, using the
outer holes on the mounting plate (B) as a template, making
sure the bracket is level. Drill pilot holes in each location.
2. Pass the mounting screws through the outer holes on
the mounting plate (B) and screw them into the wall.
3. Hang arm mount bracket (D) on wall mount plate
(B), by engaging hanger strap (E) with top hook
of hanger casting (F). Seat mast mount bracket
(D) down, fully onto hanger casting (F).
3. Secure bracket (D) to casting (F), with screw (G).
Insert mast (H) into bracket (D) positioning mast (H)
with top of slope (J) facing the user. Seat mast (H)
fully into bracket (D) and secure with screw (K).
4. Secure bracket (D) to casting (F), with screw (G).
5. Insert mast (H) into bracket (D), positioning mast (H)
with top of slope (J) facing the user. Seat mast (H)
fully into bracket (D) and secure with screw (K).
J
J
H
Customer
supplied
D
C
E
H
D
E
A
F
F
B
B
A
G
G
G
K
G
K
Slat Wall Mast Mount
Front Screw
Slat Wall Mast Mount
6
Wall Mast Mount
Front screw
Wall Mast Mount
Step 2: Attach Monitor Plate (Movement Joint Included) to the Monitors or Television
Attaching the Monitor to the Arm (Movement Joint Including) to Monitor Plate
Tools Needed
• Screwdriver or Allen wrench
1. Remove monitor base and hardware from the monitor. Retain
all hardware.
2. Place movement joint (A) against back of monitor or television,
with Knoll logo toward top of monitor and attach the VESA
plate (B) using appropriate hardware. VESA plate can
accommodate 75 mm or 100 mm hole patterns.
3. Attach movement joint (A) to arm (E) by connecting them
together, then inserting fast release pin (D).
Note: Each standard Sapper movement joint can hold up to
20 lbs. Each Sapper 50 movement joint can hold up to
30 lbs. Weight limit for mounting option specified may
be less.
Note: Check VESA compliancy and hole pattern on monitor or
television as Knoll monitor solutions are designed to work
with VESA compliant monitors only. The Knoll VESA
plate can accommodate 75mm or 100mm hole patterns.
Knoll movement joints do not ship with screws and are
designed to accept an M4 or M5 screw; length is
dependent on the specific monitor or television and
screw should be tested prior to installation to ensure
correct length; Knoll is not responsible for use of
incorrect screws. If monitor has recessed VESA mounting
surface, spacers (C) may be required between movement
joint (A) and monitor. Spacers must be requested
through Knoll Customer Service.
A VESA plate adaptor may be necessary for larger
monitors and televisions and can be ordered separately
in the sizes of 100 mm x 200mm (M5 screws), 200mm x
200mm (M6 screws), 300mm x 300mm (M8 screws) and
400mm x 400mm/400mm x 600mm (M8 screws).
Adaptors ship with separate installation instructions and
may require spacers. Knoll VESA plate adaptors ship
with screws to attach the adaptor to the Knoll VESA
plate but do not ship with screws to attach the adaptor
to the monitor or television (see screw sizes listed above,
English size equivalents may be needed instead); screw
length is dependent on the specific monitor or television
and screw should be tested prior to installation to ensure
correct length, Knoll is not responsible for use of
incorrect screws.
A
D
Customer
supplied C
B
E
A
Customer
supplied
VESA Compliant Monitor Mounting
ii_attach_monitor.eps
7
Step 3: Attach Arms with Monitors to Mast
Tools Needed
Allen wrenches (in inches)
• Top plate – 5/32” (I)
• Mast anti-dislodgement – 5/64” (D)
• Rotation braket – 3/16” (K)
1. Remove the top plate (G) and top bushing (H)
using a 5/32” Allen wrench, on screws (I).
2. Slide arm and monitor assembly (F) onto each post (J)
of the double-monitor bracket assembly (E). Reconnect
top plate (G) and top bushing (H), ensuring that each arm
assembly has full rotational movement. Reinstall screw (I).
3. Remove the mast top cap (E) and stop screw (D). Rotate
the adjustment knob (A) to the desired height. (Note:
Knoll logo, on adjustment knob should be face up).
4. Place the double monitor arm assembly (C) onto the mast
(B). With the double monitor arm assembly in place, tighten
screw (K), reinstall the stop screw (D) and top cap (E).
G
E
H
C
F
F
J
E
I
D
B
A
K
Step One
Step Two
8
Double Arm Bracket
Step Three
Features: Cable Management and Fast Release
Cable Management Gates and Clip(s)
Fast Release
To manage cables under the arm, open inboard gates (A) and (B),
by slightly moving gate up to overcome the snap detent. Feed
wires into the hollow under both arms. Snap both gates closed.
1. Fast release functionality allows rapid removal of monitor and
movement joint. Remove the fast release pin (A) from the
arm assembly (B), disconnecting the movement joint (C).
Manage cables down mast (C) and install cables management
clips (D), by snapping clip (D) over cables and onto mast (C).
Please note there will be one clip for 8” masts and two clips for all
masts 12” and longer.
2. To reinstall, position movement joint on monitor arm and insert
fast release pin (A). When fully seated, pin should be flush.
Arm Cable Management
A
A
A
B
B
Gates
C
A
C
B
D
Clips
Mast Cable Management
Cable Management
Fast Release_b
ii_fast_release_b.eps
9
Features: Friction Adjustment and Anti-Dislodgement
Tilt Friction, Rotation Friction and
Anti-Dislodgement and Theft Deterrence
Independent Monitor Movement Adjustments
Tools Needed
Tools Needed
Allen wrenches (in inches)
Allen wrenches (in inches)
• Tilt friction – 3/16”
(Included on Monitor Plate)
• Anti-theft – 1/16” (A)
• Rotation friction – 3/16” (C)
(Included on Monitor Plate)
1. Sapper monitor arms have anti-theft features. A small
set screw (A) resides inside the lower end of the fast
release pin (B). To activate anti-theft feature, use a 1/16”
Allen wrench and back set screw (A) partially out of fast
release pin (B). This prevents fast release function.
Tilt friction:
To increase friction, insert Allen wrench (included on each monitor
plate) (A) into screw (B) and turn clockwise. To reduce tilt friction,
turn screw (B) counterclockwise. Adjust in very small increments.
Rotation friction:
To increase friction, insert Allen wrench (A) (included on each
monitor plate) into screw (C) and turn clockwise. Adjust in very
small increments.
2. Also, the stop screw (C) at the top of the mast (D)
prevents monitor arm from being removed.
Movement Joint Anti-Theft
Independent monitor movement:
To tighten and increase independent monitor movement, insert
Allen wrench (included on each monitor plate) (A) into screw (D)
and turn clockwise. Adjust in very small increments.
B
A
B
B
A
A
Tilt friction
B
set screw
B
A
Friction
Adjustment
Tilt Tilt
Friction
Adjustment
A
C
Rotation friction
A
Rotation Friction Adjustment
C
D
D
Independent Monitor Movement Adjustment
10
Independent Monitor Movement Adjustment
ii_inde_moni.eps
Mast Anti-Theft
Anti-Theft
ii_anti_theft.eps