Vi1416VPD - Vigitron

Vi1416VPD
16-Channel Powered VPD Combiner
Features
• Supports up to 16 cameras by providing video, class II
power and data on a single Category 5 cable per camera
• 16 isolated camera power individually selectable 24
or 28 VAC at 1 A max per channel, 12 A aggregated
• A glass fuse per channel, accessible from front panel
• Use with the Vi1053VPD transceiver at the camera
• Power present and fault indicator LEDs for each camera
• 1U high wall or rack mountable
• Designed for structured wiring applications
• Limited lifetime warranty
Power Distance Chart
Power Supply Voltage 12 VDC 24 VAC 28 VAC
Voltage at the camera 10.8 VDC 21.6 VAC 21.6 VAC
Applications
100 mA Camera
• Security and surveillance
• Department store security
• Casino security
• Hospitals and airports
• Structured wiring applications
300 mA Camera
1 Amp Camera
Dual 24 AWG
Dual 23 AWG
Dual 24 AWG
Dual 23 AWG
Dual 24 AWG
Dual 23 AWG
448 ft.
137 m
564 ft.
172 m
896 ft.
273 m
1,130 ft.
345 m
2,388 ft.
728 m
3,010 ft.
918 m
150 ft.
46 m
190 ft.
58 m
46 ft.
14 m
58 ft.
18 m
300 ft.
92 m
378 ft.
115 m
90 ft.
28 m
114 ft.
35 m
796 ft.
243 m
1,004 ft.
306 m
240 ft.
73 m
300 ft.
92 m
Cat-5 : 24 AWG, Cat-6 : 23 AWG
The Vi1416VPD is an advanced device that combines video, PTZ data, and camera power over a single 4-pair UTP cable to simplify
CCTV installations in a structured wiring environment. It supports up to 16 cameras and is designed to be placed at a location between
the cameras and control room to extend the video up to 3,000 ft. (915 m). The Vi1416VPD has a 16-channel fully isolated class II built-in
28/24 VAC power supply. Each camera power output is equipped with a glass fuse for extra protection. All fuses are easily accessible
from front.
At the camera end the Vi1053VPD video balun/combiner provides video, power and data on separate outputs. The Vi1416VPD can be
installed at the "head end" or “mid-span”. The video signals are cnnected through 4 RJ45 and Category-5 cables to passive or active UTP
receivers at the control room. The data connections to the DVR are through 4-pair RJ-45 cables. There is a separate data connection for
each camera. All equipment follows industry-standard EIA/TIA 568B pinouts. The Vi1416VPD is an ideal CCTV component for structured
cabling environments.
Application Diagram
Cat-5
1053VPD
Vi1416VPD; 16-Ch Powered VPD Combiner
Cat-5
Video
Data
Video
Data
Vi6116; 16-Ch Active Receiver
Camera # 2
1053VPD
Power
Data
110 V AC
Analog
Matrix
Switch
Camera # 1
Power
Data
Cat-5
Camera # 3
1053VPD
Data
Local Power
RoHS
The smart choice for quality video
www.vigitron.com
DSVi1416VPD_0212
Technical Specification*
Ordering Information
Electrical
Description
8-Ch Powered VPD Combiner
16-Ch Powered VPD Combiner
PART No.
Vi1408VPD
Vi1416VPD
Input Voltage
Input Current
Camera Power
110 VAC or 220 VAC, externally switch selectable
4.8 A (110 VAC) / 2.4 A (220 VAC)
Voltage: Isolated class II, switch selectable
24 VAC, off, or 28 VAC
Current: 1 A maximum per camera, 12 A maximum aggregated
Total power: 340 VA
Fault Protection
2 A glass fuse (front access) per camera
Twisted Pair (UTP) 100 Ohms +/- 20%, 24 AWG minimum, Category 2-7
Diagnostics LEDs No load or shut down: 16 red LEDs, one per channel
Power present: 16 green LEDs, one per channel
Connectors
Camera connection: RJ-45 connector
Data: RJ-45 connector
Control room video: RJ-45 connector
Transient Immunity per ANSI 587 C62.41
System Configuration
Environmental
Humidity
Temperature
Vi1416VPD
0 to 95%, non-condensing
Operating: -20°C to +50°C
Storage: -30°C to +70°C
5 cft./min
1300 BTU/hour
Minimum Airflow
Heat
Mechanical
Dimensions
Weight
Material
750 ft.
228 m
1.75x17x12 in., 4.3x43x30.5 cm (HxWxL)
22 lb, 10 kg
Steel sheet metal
1
4
8
16
32
Mounting brackets for front, rear or wall installations
Rubber feet for desk applications
Moulded IEC 7-ft. (200 cm) power cord
*Specifications are subject to change without notice.
VB1001F/M
VB1007M
Vi1001F/M/P
Vi1003M
Vi1006M
Vi1004
Vi1008
Vi1016
Vi1032
1
4
8
16
32
Control Room Data Connections:
Camera Connections:
Pin#
1
2
3
4
5
6
7
8
VPD
Video +
Video
Data +
Power
Power +
Data
Power +
Power
Camera 1-4 Camera 5-8
Data-1
Data-1
Data-2
Data-3
Data-3
Data-2
Data-4
Data-4
+
+
+
+
-
Data-5 +
Data-5 Data-6 +
Data-7 Data-7 +
Data-6 Data-8 +
Data-8 -
Pin#
1
2
3
4
5
6
7
8
Camera 9-12 Camera 13-16
Data-9 +
Data-9 Data-10 +
Data-11 Data-11 +
Data-10 Data-12 +
Data-12 -
Data-13 +
Data-13 Data-14 +
Data-15 Data-15 +
Data-14 Data-16 +
Data-16 -
3,000 ft.
915 m
Active Receivers
Model
Channels
Passive Transceivers
Channels Model
Included Accessories
Pin#
1
2
3
4
5
6
7
8
Maximum Cable
Distance
Vi6100VR/Vi6200VR
Vi6104/Vi6204
Vi6108/Vi6208/Vi6308
Vi6116/Vi6216/Vi6316
Vi6132/Vi6232/Vi6332
2,000 ft. (610 m) for Vi6200 series
Control Room Video Connections:
Camera 1-4 Camera 5-8
Video-1+
Video-1 Video-2 +
Video-3 Video-3+
Video-2 Video-4 +
Video-4 -
Video-5+
Video-5 Video-6 +
Video-7 Video-7+
Video-6 Video-8 +
Video-8 -
Camera 9-12 Camera 13-16
Video-9 +
Video-9 Video-10 +
Video-11Video-11+
Video-10 Video-12 +
Video-12 -
Video-13 +
Video-13 Video-14 +
Video-15 Video-15+
Video-14 Video-16 +
Video-16 -
1.75"
Camera -1
Camera -2
Camera -9
Camera -10
24 V
28 V
24 V
28 V
28 V
24 V
24 V
28 V
28 V
24 V
24 V
Camera -3
Camera -4
Camera -11
Camera -12
28 V
28 V
24 V
24 V
28 V
28 V
24 V
24 V
Camera -5
Camera -6
Camera -13 Camera -14
28 V
28 V
24 V
24 V
28 V
28 V
24 V
24 V
Camera -7
Camera -8
28 V
24 V
Camera -15 Camera -16
28 V
24 V
Video 1-4
Video 5-8
Video 9-12
Video 13-16
Control Room Data
28 V
Control Room Video
19"
Data 1-4
Data 5-8
Data 9-12
Data 13-16
Vi1416VPD
16-Ch Powered
VPD Combiner
Power Out:
24/28 VAC,1A Max/CH
12A Max Total
Rear View
POWER
Vi1416VPD
Front View
Wire and Cable Recommendations
The Vigitron products are designed to be used with unshielded twisted pair (UTP) wiring. The UTP wire must be 24AWG - 12AWG or Category 2-7 cable.
Multi pair cable with an overall shield is acceptable, however individually shielded pairs should be avoided. Multiple UTP video feeds can be operated in
the same communication cable along with telephone, computer, control signals and low power voltages. While UTP video may be routed through
punch-down block terminals, any resistive, capacitive or inductive devices (such as T-taps or MOV's) must not be used. Please contact Vigitron for more
specific information regarding wire types and proper installation techniques.
TEL (+1) 858 - 484 - 5209 • FAX (+1) 858 - 484 - 1205
7810 Trade Street, Suite 100, San Diego, CA 92121, USA • support@vigitron.com • www.vigitron.com
© Copyright 2012 Vigitron, Inc.