ENGAGING SPOT LOCK
1. Press the Spot Lock button on the remote.
2. The Memory Location icon will flash on the remote
LCD for three seconds, allowing you to choose a
memory location by pressing the Speed Up or Speed
Down buttons. Pressing the Spot Lock button again or
waiting for three seconds accepts the memory location.
DISENGAGING SPOT LOCK
1. To disengage Spot Lock press any of these buttons:
Prop On/Off, Steer Right, Steer Left, Speed Up,
Speed Down or Spot Lock.
RE-ENGAGE A SAVED SPOT
LOCK LOCATION
1. Manually navigate the boat to within a quarter mile of
the saved Spot Lock location. Due to safety reasons,
i-Pilot will not re-engage a saved Spot Lock location
greater than a quarter mile away.
2Press the Spot Lock Recall button on the remote.
3. The Memory Location icon will flash on the remote
LCD for three seconds allowing you to choose a
memory location by pressing the Speed Up or Speed
Down buttons. Pressing the Spot Lock Recall button
again or waiting for three seconds accepts the
memory location.
SPOT LOCK ESCAPE
1. If the Spot Lock button is accidentally hit, press the
Record Pause/Escape button or any manual navigation
button within three seconds to cancel the command.
Engaging Cruise Control
1.Press the Cruise Control button on the remote.
2. The current GPS speed will flash, displaying your
current speed as the target GPS speed on the remote
LCD for three seconds.
3.Press the Speed Up or Speed Down buttons to
increase or decrease the target speed or press the
Cruise Control button again to engage Cruise
Control immediately.
Disengage Cruise Control
1.Pressing the Cruise Control button will disengage
Cruise Control.
Adjusting Target Speed with
Cruise Control Engaged
1.With Cruise Control engaged press the Speed Up
or Speed Down buttons to adjust the target speed
by 0.1 MPH increments.
Engaging Advanced
AutoPilot and AutoPilot
1. To engage Advanced AutoPilot, press the AutoPilot
button once. To engage AutoPilot, press and hold the
AutoPilot button for two seconds.
2. The Advanced AutoPilot or AutoPilot icon will be
displayed on the remote LCD.
3. To adjust desired heading, manually steer motor to new
heading. i-Pilot will lock onto new heading.
Recording a Track
1.Press the Record button on the remote.
2. The Memory Location icon will flash on the remote
LCD for three seconds, allowing you to choose a
memory location by pressing the Speed Up or
Speed Down buttons. Pressing the Record button
again or waiting for three seconds accepts the
memory location.
3. The REC icon will be displayed on the remote LCD.
Remember this will be the start point on the track.
4. Navigate the boat along the desired path or course.
AutoPilot and/or Cruise Control can be used while
recording a track.
5.Press the Record button on the remote again to stop
the recording. The recording will end automatically if
the two-mile distance limit is reached for the track or
if one of the following buttons are pressed: Spot Lock,
Spot Lock Recall, Track to End or Track to Start.
Pause and Resume a Recording
1. While recording a track press the Record
Pause/Escape button.
2. The record icon will flash on the remote LCD.
3. i-Pilot has now paused the recording of the track.
4. If the boat moves farther than a quarter mile from
where the Record Pause/Escape button was pressed,
the recorded track will be ended and saved to the
memory location previously selected.
5. When ready to resume recording, navigate the
boat just ahead of where the Record Pause/Escape
button was pushed. Failure to do this may cause erratic
play back of a track.
6.Push the Record Pause/Escape button.
7. The record icon will stop flashing on the remote LCD.
8. i-Pilot is now recording again and adding to the
track that was paused.
Replaying a Track
(Track to Start / Track to End)
1. Manually navigate the boat to within a quarter mile
of the saved track. Due to safety reasons, i-Pilot will
not re-engage a saved track greater than a quarter
mile away.
2.Press the Track to Start or Track to End button on
the remote.
3. The Memory Location icon will flash on the remote
LCD for three seconds, allowing you to choose a
memory location by pressing the Speed Up or
Speed Down button. Pressing the button pressed
in step 2 again or waiting for three seconds accepts
the memory location.
4. Adjust motor speed to desired setting to engage and
navigate track automatically.
Record, Track to End and Track
to Start Escape
1. If the Record, Track to Start or Track to End
button is accidentally hit, press Record Pause/Escape
button within three seconds on the remote to cancel
the command.