VANDAL RESISTANT
BACK-LIT WEATHERPROOF
ACCESS CONTROL KEYPAD
lin
on
ry
t
en
or
Do
td
eL
K301A
User Manual (MK-II)
FOR ELECTRIC LOCK, INTER-LOCK
AND SECURITY SYSTEM INSTALLATIONS
TABLE OF CONTENTS
INTRODUCTION
························································································································· 5
FEATURES
·································································································································· 5
OPTIONAL DEVICES FOR SYSTEM EXPANSION ····································································· 5
SPECIFICATIONS ······················································································································· 6
··························································································································· 7
t
en
or
Do
INSTALLATION
Precautions ································································································································ 7
CONNECTION TERMINALS ·································································································· 8-10
OTHER FACILITIES
··················································································································· 11
On-Board LED Indicators ·········································································································· 11
Pacifier Tone & The LED Signals ······························································································· 11
Jumper for Back-Lit Selection ···································································································· 11
PREPARATION FOR PROGRAMMING ······················································································ 12
A) Criteria for Codes ················································································································· 12
B) Security Level of The Operation Media
················································································· 12
PROGRAMMING AND OPERATION ····················································································· 13-42
Power Up The Keypad ·············································································································· 13
Set Keypad into Programming Mode with Master Code
Master Code
ry
···························································· 13
Direct Access to Programming Mode with The “DAP” Code – 2 8 2 8 ··········································· 14
System Refreshing with “Refreshing Code” --- 9 9 9 9 ······························································ 14
The Default Values after Refreshing ·························································································· 15
on
····························································································································· 16
Super User Code ······················································································································· 16
Operation and Functions of The Super User Code ··························································· 17-18
User Codes For Output 1 & 2 ···································································································· 19
Examples – Programming And Operation ············································································ 20-21
Visitor Codes (For Output 1 Only)
······················································································ 22-23
lin
Duress Codes (For Outputs 1 & 2 ) ····················································································· 24-25
Operation And Function of The Duress Code ········································································ 25
Output Modes & Timing for Output 1 and 2 ·············································································· 26
System Real-Time-Clock ············································································································ 27
Start & Stop Times For Daily Inhibition of Output 1 ····························································· 28-29
User Code Entry Mode - Auto or Manual
······················································································ 30
eL
Personal Safety And System Lock-Out
··················································································· 31
Pacifier Tones On-Off Selection ································································································· 31
Output Operation Announcer ··································································································· 32
Status LED Flashing On-Off during Standby ·············································································· 32
Door Forced Open Warning & Timing
Intelligent Egress Button – An Unique Feature of A Contemporary Keypad
Where And Why “Going Out” Needs Attention
Egress Delay , Warning And Alarm
td
······················································································· 33
Door Propped-Up Warning & The Delay Time ············································································33
·······························34
······························································· 34-35
······················································································ 36-37
TABLE OF CONTENTS
Operation Modes ························································································································· 38
Close The Programming Mode ···································································································· 38
Programming - General Users·······································································································39
t
en
or
Do
Programming Summary Chart ····························································································· 40-41
Application Examples ·········································································································· 42-43
Stand alone Door Lock ············································································································· 42
Inter Lock System Using Two Keypads ···················································································· 43
lin
on
ry
td
eL
INTRODUCTION
K301A is a self-contained two output relay, vandal resistant and weatherproof keypad. It has been
designed for full feature stand alone access control applications
The keypad is ideally for door strike and alarm arm-disarm controls. It is also a programmable
industrial timer (from 1 second to over 24 hours) for automatic operator system.
t
en
or
Do
K301A (Standard Version):
Output Relay 1 – 5A Rating N.C. & N.O. Contacts for Door Lock Actuation Control
Output Relay 2 – 1A Rating N.C. & N.O. Contacts for Auxiliary Device Control
ry
on
FEATURES
A member of the Tri-Tech series keypads compatible with the optional controllers & reader keypads
for system expansion
Loaded with the K301A MK-II operation software
lin
Built-in with all the logics for stand alone, split-decoded and multi-station operations
Controls “Going in” with User Codes and “Going out” with feature programmable egress button
Independent control for the two output relays with programming timer
eL
Total 1,100 User Codes for controlling of the two outputs
Indoor or outdoor installation with IP-66 all weather ingress protection
Stainless steel faceplate combines with die-casting metal back-lit key buttons
Vandal resistant die-casting metal housing for surface or gooseneck mounting
td
Package Contents
•
•
•
•
One
One
One
One
K301A Keypad
Pack of Mounting Screws
Centre Pin Torx Screw Wrench
User Manual
5
SPECIFICATIONS
Operating Voltage:
12V-24V AC/DC, Auto adjusting
Operating Current:
20mA (quiescent) to 90mA@12VDC
10mA (quiescent) to 45mA@24VDC
t
en
or
Do
Storage and Operation Temperature:
-20 C to +70 C
Storage and Operation Humidity:
5-95% relative humidity non-condensing
Working Environment & Ingress Protection:
All weather, IP-66
Number of Users:
Output 1 – 1,000 (User Codes) + 50 Duress Codes
Output 2 – 100 (User Codes) + 10 Duress Codes
Number of Visitor Codes:
50, programmable for one time or with time limit
Timings for Code Entry:
10 seconds waiting for next digit entry
The Timers:
Egress Button:
ry
1-99,999 Seconds (Over 24 Hours possible) Independent Programmable Timers for O/P 1 & 2
Programmable for Instant, Delay with Warning
Momentary or Holding Contact for Exit Delay
on
Input Sensing Terminals:
a) Door position, b) Egress, c) O/P 1 inhibit
Output Control Terminals:
lin
Transistor Open Collector 24VDC/100mA sink Max for the following outputs
a) Duress, b) Key Active, c) Inter-lock
Output Contact Ratings:
Output Relay 1 – N.C. & N.O. dry contacts, 5A/24VDC Max.
Output Relay 2 – N.C. & N.O. dry contacts, 1A/24VDC Max.
Tamper Switch – N.C. dry contact, 50mA/24VDC Max.
eL
Dimensions:
125(H) X 79(W) X 46/54(D)mm
Weight:
510g net
td
Housing:
Die-Cast Aluminum, Powder-paint coating
Faceplate Material:
1.5mm stainless steel
6
INSTALLATION
ASSEMBLY
on
ry
t
en
or
Do
PRECAUTIONS
In previous experience, most of the damages caused in the installation are accidental touching of the
components on circuit board with the wires carrying power. Please be patient to study the manual to
become familiar with the specifications of the system before starting the installations.
lin
Do not apply power to the system while it is in installation.
Check carefully all the wirings are correct before applying power to the system for testing.
td
eL
7
CONNECTION TERMINALS
t
en
or
Do
BACK-LIT JUMPER
CONNECTION
TERMINALS
on
ry
1 - 2 : 12 - 24V AC/DC (Power Input Terminal)
Connect to 12-24V AC or DC power supply. The (-) supply and (-) GND (terminals 2
& 12) are the common grounding points of the keypad system. No selection jumper
is required for the full input voltage range. Connect DC power with the (+) and (-)
polarity indicated; and there is no polarity discrimination for AC power input.
lin
3 - 4 - 5 : OUTPUT 1 (Output Relay 1)
5 Amp relay dry contact controlled by the Group 1 User Codes, recommended for
door strike. Terminal 3 is Normally Closed (N.C.), terminal 5 is Normally Open (N.O.)
and terminal 4 is the common point of the two contacts. Use N.C. output for Fail-safe
locking device; and N.O. output for Fail-secure locking device. The relay is
programmable for Start/Stop (toggle) mode or Momentary timing mode. See
programming Location 51 for the details.
eL
6 - 7 - 8: OUTPUT 2 (Output Relay 2)
1 Amp relay dry contact with N.C. and N.O. outputs. Terminal 6 is the N.C.(Normally
Closed). terminal 8 is N.O. (Normally Open) and terminal 7 is the common point of
the two contacts, which is prepared for actuating auxiliary device controlled by the
keypad; or external door chime actuation controlled by the bell button. The
maximum rating of the relay contacts is 24 VDC/1A.
td
K301A - Standard Version
The Output relay 2 in K301A is controlled by the Group 2 User Codes. It is
programmable for Start/Stop (toggle) mode or Momentary Timer mode. See
programming Location 52 for the details.
8
9: EG IN ( Egress Input)
t
en
or
Do
A Normally Open (N.O.) input terminal referring to (-) ground. With the help of connecting a normally
open button to activate Output 1 for door opening like using Codes.
Egress button is usually put inside the house near the door. More than one egress buttons can be
connected in parallel to this terminal. Leave this terminal open if not used.
See Programming Locations 90 for more information about the Egress Button with programmable
features.
10: KEY ACT O/P (Keypad Active Output)
An NPN transistor open collector output with maximum power rating of 24VDC/100mA sink. It is
equivalent to an N.O. (Normally Open) terminal referring to ground. It can be used to drive small
power device, such as a relay or a low power control point for other equipment.
11: DU OUT (Duress Output)
An NPN transistor open collector output with maximum power rating of 24VDC/100mA sink. It is
equivalent to an N.O. (Normally Open) terminal switching to (-) ground after the Duress Code is
entered. Use it to trigger an alarm zone of a security system, or turn on a buzzer to notify a guard.
12: (-) GND (Common Ground)
A grounding point of the keypad that is common to terminal 2.
ry
13: DOOR SENS N.C. (Door Position Sensing Input -- Normally Close)
A Normally Closed (N.C.) sensing point referring to (-) ground, with the help of a normally closed
magnetic contact monitors the open or close status of the door. It initiates the following functions for
the system. Connect it with jumper to (-) Ground if not used.
on
a) Door Auto Re-lock
The system immediately re-locks the door after it is re-closed before the end of the programmed time
for output 1. It prevents unwanted “tailgate” entry.
lin
eL
b) Door Forced Open Warning
The keypad generates “door forced open” warning instantly once the door is forced to open without
a valid user Code or egress button. The warning lasts as long as the time programmed (1-999 sec).
It can be stopped with an User Code for output 1 at anytime. See programming Location 80 for the
details.
c) Door Propped-up Warning
The keypad generates propped-up warning beeps while the door is left open longer than the
allowable time programmed. The warning will last as long as the door is open until re-closed. See
programming Location 81 for the details.
td
d) Inter-lock Control
The inter-lock control output always goes to (-) while the door is open, which gives signal to disable
the partner keypad in an inter-lock system. See the Inter-lock terminal 15 description for more
information.
9
14: O/P 1 INHIBIT N.O. (Output 1 Inhibit Control Input – Normally Open)
A Normally Open (N.O.) sensing input point for controlling the Output 1, with this terminal connecting
to (-) ground, the Egress Button, the group of User PINs for Output 1 are all disabled. It is
prepared mainly for the cross wire connection with the “Inter-lock O/P” point of the partner keypad in
an Inter-lock system.
t
en
or
Do
NOTE: The inhibit function does not govern the Duress Codes and the Super User Codes. They are
always valid
15: INTER-LOCK O/P (Inter-lock Control Output)
An NPN transistor open collector output with maximum power rating of 24VDC/100mA sink. It is OFF
at normal condition and it switches to (-) ground immediately for the first 5 seconds after keying in a
valid User Code to operate Output 1, then, it will keep tying to (-) ground during the Door Position
Sensor is open circuit due to door opening. Use this output point to make cross wire connection with
the partner keypad’s “O/P 1 Inhibit” point in an Inter-lock system to prevent both doors can be opened
at the same time.
An Inter-lock System:
An inter-lock system is a two-door system that always allows only one of the doors to open during the
operation. While one of the doors is opened, the other door keeps close until the open door is re-closed.
It prevents the unauthorized people dashing into a protected area while the doors are in use.
An inter-lock system needs two keypads and two door position sensing switches for the two doors.
on
ry
16 - 17: TAMPER N.C. (Tamper Switch Normally Closed Contact)
A normally closed dry contact while the keypad is secured on its box. It is open while keypad is
separated from the box. Connect this N.C. terminal to the 24 hour protection zone of an alarm system
if necessary.
lin
18: DATA I/O PORT (Data Communication Bus)
Data I/O port is prepared for setting up a data bus for the connection of the auxiliary reader-keypads
and the split-decoder in system expansion. See the examples in “Application Expansions” section for the
details.
td
eL
10
OTHER FACILITIES
ON-BOARD LED INDICATORS
RED / GREEN (Right) --AMBER (Centre) ---------
t
en
or
Do
----------
It lights up in Green for Output 1 activation; Red for Output 1 inhibited
and flashing during inhibition paused.
It flashes in Standby. It shows the system status in synchronization
with the beep tones. The standby flashing can be OFF with
programming. See Location 73 for the details.
It lights up in Red for output 2 activation.
RED (Left)
PACIFIER TONES & THE LED SIGNALS
The buzzer and the amber LED indicator give following tones and signals respectively for system
status:
TONES *
11) Real -time-clock stopped after
power failure
AMBER LED
----1 Beep
2 Beeps
5 Beeps
Continuous Beeps
1 Second Long Beep
--------1 Long Beep
Continuous 1 Beep/5 secs
Continuous 3 Fast Beeps
/5 secs
ry
STATUS
1) In Programming Mode
2) Successful Key Entry
3) Successful Code Entry
4) Unsuccessful Code Entry
5) Power Up Delay
6) Output Relay Activation **
7) In Standby ***
8) System Refreshing
9) Code Already Stored in System
10) Keypad link-up with Decoder Failed
ON
1 Flash
2 Flashes
5 Flashes
Continuous Flashes
----1 Flash in 1 Second Interval
Fast Flashes for 2.5 Minutes
-------------
on
lin
NOTE:
All Pacifier Tones can be ON or OFF through the programming option at Location 71
*
* * The Output Relay Activation beep can be selected through the programming option at
Location 72
* * * The Standby flashing can be ON or OFF through the programming option at Location 73
JUMPER FOR BACK-LIT SELECTION
2) Auto Back-lit ---
The backlit is OFF in standby. It turns to
full backlit when a key button is pressed,
then back to OFF 10 seconds after the last
key button is pressed.
3) OFF
---
td
The keypad gives dim backlit in standby. It
turns to full backlit when a key button is
pressed, then back to dim backlit 10
seconds after the last key button is
pressed.
eL
1) Full Back-lit ---
BACK-LIT
JUMPER
Back-lit function disabled.
11
PREPARATION FOR PROGRAMMING
A) CRITERIA FOR CODES
t
en
or
Do
Prime Codes
a) User Codes
b) Master Code
c) Super User Code
d) Visitor Codes
All these codes MUST be unique. It is not allowed to repeat a prime code for second function.
All the codes in this system can be 4-8 digits for Manual Entry Mode. The codes must be in the same
digit length with the Master Codes for Auto Entry Mode. See Location 70 for the details.
NOTE:
The keypad will reject repeated use of prime code in programming and give one long beep
indication.
B) LIST OF USER INFORMATION
ry
The keypad can accommodate up to 1,000 users for door control and 100 users for auxiliary control.
To avoid confusion and for programming convenience, it is suggested to make a list recording of the
user information. It helps the owner to program the user codes smoothly and to trace them
afterwards in the future. Here is a suggested format of the list.
List of Users (See page 19-21 for reference)
Name
Location
John
May
Tom
Tracy
Bill
10
10
10
10
20
User ID
001
002
003
004
001
Code
3456
1234
24680
13579
5678
lin
Remark
Output 1
Output 1
Output 1
Output 1
Output 2
td
eL
User
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
--
on
Example:
1,000
12
PROGRAMMING & OPERATION
POWER-UP THE KEYPAD
The keypad gives power-up delay of 1 minute after power has been applied. It is the time frame
designed for setting the keypad to programming mode with DAP code. See the details of “DAP
CODE – 2 8 2 8” below.
1) The keypad gives continuous beeps for 1 minute after power-up.
t
en
or
Do
2) The power-up delay can be stopped instantly with 12#
if the delay beep is found annoying
and setting the keypad to programming mode with DAP code is not required.
POWER-UP DELAY STOP
VALIDATION
12
#
3) The keypad will set itself to Normal Operation Mode automatically after the 1 minute power-up
delay expired or it is stopped with 12#
.
ry
SET KEYPAD IN PROGRAMMING MODE WITH MASTER CODE
on
It is always necessary to set the keypad in programming mode for feature programming
The keypad is in normal operation after power-up delay. Set it in programming mode with Master
Code and validate it with
lin
MASTER CODE
VALIDATION
eL
NOTE:
a) For the owner’s convenience in programming at the first time, a Master Code 0 0 0 0 has been
put into the keypad before exit-factory. It is NOT a default code. For security reason, owner
should program a personal Master Code to replace it after the keypad is owned.
td
b) The Mains LED (amber) is ON after the keypad confirms it in programming mode with 2 beeps.
d) DO NOT turn off power while the keypad is in programming mode. Otherwise, it may cause error
to the data in memory.
13
DIRECT ACCESS TO PROGRAMMING MODE WITH “DAP” CODE -- 2 8 2 8
In case the Master Code is forgotten, apply the following procedures precisely to set keypad
into programming mode with DAP code:
1) Switch OFF all the power for 1 minute to ensure that the keypad is fully discharged.
t
en
or
Do
2) Switch ON power again. The keypad is in Power-up Mode for 1 minute. The buzzer gives
continuous beeps and the Status LED is flashing. This is the only time frame to accept the DAP
code.
3) Press the Egress Button (the button connecting accross EG IN, (Terminal 9) and (-)GND,
(Terminal 15) once to enable the keypad for accepting DAP code. The power-up beep stops after
the Egress Button is pressed.
. .
4) Key in the DAP code
and validate it with
(or
). The Status LED is
ON and the keypad is in programming mode like using Master Code. It is ready to accept new
programming data as long as you like until exit programming mode.
EGRESS BUTTON
DAP CODE
VALIDATION
PRESS ONCE
5) To program a new Master Code to replace the old one. See “Record A Master Code” stated at
“Location 01” for the details.
ry
lin
on
NOTE:
The keypad will set itself to normal operation mode 1 minute after power-up if the Egress Button is
not pressed and the DAP code is not keyed in. To set keypad back to power-up mode, repeat
procedures 1-4.
SYSTEM REFRESHING WITH “REFRESHING CODE” --- 9 9 9 9
The keypad can be refreshed by cleaning all the programmed old data and set it back to default
values except the Master Code.
eL
REFRESHING CODE
VALIDATION
td
NOTE:
a) Make sure that system refreshing is really required before entering the refreshing code.
b) Refreshing takes few minutes. The status LED (amber) keeps flashing during refreshing.
c) The keypad is back to its default value after refreshing. Re-program of the desired values are
necessary.
14
THE DEFAULT VALUES AFTER REFRESHING
80
81
90
PARAMETERS
Master Code
Common User Code 2
User Codes for O/P 1
User Codes for O/P 2
Visitor Codes
Duress Code for O/P 1
Duress Code for O/P 2
O/P Mode of The O/P 1
O/P Mode of The O/P 2
System Real-Time-Clock
Start & Stop Time
Personal Safety & Lock-out
User Code Entry Mode
Pacifier Tones ON-OFF Selection
O/P Operation Announcer
Status LED Standby Flashing ONOFF
Door Forced Open Warning & Timing
Door Propped-up Warning & Delay
Egress Delay & Warning
94
Operation Modes
DEFAULT FUNCTIONS & VALUES
0 0 0 0 Factory Set, Not a default value *
Nil ----- User Program Required
Nil ----- User Program Required
Nil ----- User Program Required
Nil ----- User Program Required
Nil ----- User Program Required
Nil ----- User Program Required
Time = 5 Sec, Momentary
Time = 5 Sec, Momentary
Nil ----- User Program Required
Nil ----- User Program Required
Code = 1, 10 False Code Lock-out 60 Sec
Code = 2, Manual Entry Mode
Code = 1, Pacifier Tone ON
Code = 1 Sec, Notification Beep ON
Code = 1, Flashing Enabled
Code = 0, Warning Disabled
Code = 0, Warning Disabled
Code 1 = 0, Instant, No Delay
Code 2 = 1, Momentary Contact without Warning
Code = 0 , Keypad Mode
ry
t
en
or
Do
LOCATION
01
04
10
20
40
41
42
51
52
55
56
60
70
71
72
73
lin
on
NOTE:
The DAP Code 2 8 2 8 and the Refreshing Code 9 9 9 9 are fixed in the operating system program.
It can not be changed in any ways.
td
eL
15
MASTER CODE
(Location 01)
LOCATION
MASTER CODE
01
VALIDATION
#
4 to 8 Digits
(1)
(2)
(3)
(1) LOCATION
01
t
en
or
Do
Key in Location
(2) MASTER CODE
Master Code is the authorization code for setting the system to programming mode. It is NOT
an User Code operating the output relays.
The Master Code can be 4 to 8 digits.
When a new master code is keyed in and confirmed, the old master code is replaced.
The master code is also the Link-up Code between the keypad and the optional decoder in
Split-decoded operation.
(3) VALIDATION
Press
key once. Two-beeps confirms the entry.
Example:
Set a Master Code “2 2 3 3” ----
ry
SUPER USER CODE
(Location 02)
LOCATION
on
The Super User Code has TWO functions. It is prepared to operate the three outputs and make
operation of inhibit enable / disable to those outputs.
SUPER USER CODE
VALIDATION
4 to 8 Digits
#
02
(2)
(1) LOCATION
Key in Location
02
(3)
lin
(1)
eL
(2) SUPER USER CODE
The Super User Code can be 4 to 8 digits.
When a new Super User Code is keyed in and confirmed, the old one is replaced.
Pressing
#
td
(3) VALIDATION
key to confirm code entry.
Example:
a) Set a Super User Code “2 5 8 0” ----
b) Deleted a Super User Code from memory: Key in the Location number and #. ----
16
OPERATION AND FUNCTIONS OF THE SUPER USER CODE
1) Operate Output 1 and 2
The operation of the Super User Code is just like a normal User Code. Simply key-in the Code
with a specific output number for the desired Output. The Super User Code can also be used to
reset an operating output timer instantly.
---------- Output 1 Activates or Resets
SUPER USER CODE
---------- Output 2 Activates or Resets
t
en
or
Do
SUPER USER CODE
Optional Functions Controlled by Super User Code for Output 1
Apart from controlling of the two outputs 1 and 2; the Super User Code can also be used to
enable the optional functions controlling Output 1 for user convenience or security enhancement.
Super User Code and Egress Button are excluded from any system inhibition and lockup
functions; they are valid for door open at anytime for safety.
2) Override The Door Lock Controlled by Output 1 (Keep Door Un-locked)
The Output 1 is usually for door lock control. In some situations, the door may require un-locked
for a period of time to allow door opening without User Code for entry / exit convenience. This
function Starts / Stops in toggle with the following code entry.
NOTE :
---------- The Door is Un-locked, Start / Stop in Toggle
on
ry
SUPER USER CODE
The door is un-locked while the function is enabled. The “Output 1” LED (Green) turns ON.
Do not forget to stop this function after use because the door is un-locked. Also, the system
refuses the optional functions (3) & (4) while Override function comes into effect.
This feature is good for all the “Fail-safe electric locks”.
lin
“Fail-secure electric lock” requires power to keep in un-locked condition. It takes high current all the
time while the function comes into effect and may cause damage to it. This function is not
recommended for Fail-secure electric lock.
td
SUPER USER CODE
eL
3) Pause The Scheduled Daily Inhibition for Output 1 (Temporarily Disable The Inhibition)
The scheduled inhibition can be programmed and applied to Output 1 with daily start and stop
times. It can be stopped temporarily if required; such as the staff work overtime after office
hours going into the inhibition period. This function Starts / Stops in toggle with the following
code entry. It can be done before or during the inhibition period.
---------- Door Lock Operation Resumes, Start / Stop in Toggle
NOTE :
• The “INHIBIT” LED (Red) is ON in inhibition and turns to Flashing while pause is into effect.
• See Programming Locations 55 & 56 for more information Daily Inhibition.
17
4) Inhibit All The User Codes for Output 1 (Disable Access Control Manually)
To enhance the security of the access control keypad, the owner can stop the keypad after office hour
or while the house is nobody inside. Once the Output 1 (for door lock control) is inhibited, all the User
Codes for it become invalid and those people holding the User Code are refused. This function Starts
/ Stops in toggle with the following code entry.
SUPER USER CODE
------ Door Lock Operation Inhibited, Start / Stop in Toggle
t
en
or
Do
NOTE :
• The door is locked during Output 1 inhibited and the “INHIBIT” LED (Red) is ON.
• Inhibition applies to all User Codes for Output 1 only. Output 2 is not affected.
lin
on
ry
td
eL
18
USER CODES FOR OUTPUT 1 & 2
LOCATIONS
MEDIA
(Locations 10 & 20)
USER ID
USER CODE
VALIDATION
OR
(1)
(2)
(3)
(4)
(5)
t
en
or
Do
(1) LOCATIONS (User Groups)
10 – Group 1 – 1,000 User Codes for controlling Output 1
20 – Group 2 – 100 User Codes for controlling Output 2
(2) MEDIA (Operation Media)
2 – User Codes – 4-8 Digits
5 – Delete User Codes from
0999
the selected User ID – Delete a user code by keying in
its ID.
– Group Clearing. Clear all the User Codes of the selected User Group Location.
Clearing takes few seconds to a minute.
ry
(3) USER ID (The IDs of The User Codes)
(4) USER CODE
Key in User Code into each assigned User ID.
(5) VALIDATION
key once. Two-beep confirms the entry.
td
eL
Press the
lin
on
000 – 999 – 1,000 User IDs for the User Codes in User Group 1 (Output 1)
001 – 100 – 100 User IDs for the User Codes in User Group 2 (Output 2)
19
EXAMPLES – PROGRAMMING AND OPERATION
1) Example 1 -- User Code for Output 1 :
i) Programming :
t
en
or
Do
(a)
(b)
(c)
(d)
(e)
(a) The User Code is programmed for Output 1
(b) Record a User Code
(c) Take ID number 001 in Group 1 to store the User Code, which is one of the IDs in 000-999
(d) Key in the User Code "2 4 6 8" into the storage location
(e) Press # to store the “User Code” into memory, two-beep confirms a valid entry
ii) Operation : (while the system is back to operation mode)
(a)
(b)
(a) Key in the User Code “2 4 6 8”
(b) Confirm it with the # key. Output 1 activates
2) Example 2 -- User Code for Output 2 :
(a)
(b)
(c)
ry
i) Programming :
(d)
(e)
on
(a) The User Code is programmed for Output 2
(b) Record a User Code
(c) Take ID number 001 in Group 2 to store the User Code, which is one of the IDs in 001-100
(d) Key in User Code “1 2 3 4” into the storage location
(e) Press # to confirm and store the “User Code” into memory, two-beep confirms a valid entry
td
eL
(a)
(b)
(a) Key in the Private User Code “1 2 3 4”
(b) Confirm it with the # key. Output 2 activates
lin
ii)Operation : (while the system is back to operation mode)
20
3) Example 3 -- Delete a User Code (for O/P 1, 2) :
i) Delete A User Code
User ID
(a)
(b)
(c)
(d)
t
en
or
Do
a) Key in the User Group that the User ID belongs to. “10” for the Group 1, “20” for the Group 2
b) Key in “5” that is the Command Code for making a deletion here
c) Key in the User ID that stored the User Code
d) Press the # key. Two-beep confirms a valid entry and the User Code in that User ID is cleared
4) Example 4 – Clear The Whole Group of Users :
Whole group of users can be cleared with the following command.
(a)
(b)
(c)
a) The User Group 1 – “10” is selected to be cleared. “20” for Group 2
b) Key in the Group Deletion Command, 0 9 9 9
c) Confirm the deletion with #. All the User Codes in the Group 1 are cleared. It takes a few
seconds to a minute to complete depending on the data stored.
lin
on
ry
td
eL
21
VISITOR CODES (FOR OUTPUT 1 ONLY)
(Location 40)
The Visitor Codes are temporary user codes for Output 1 (mainly for door strike in access control).
They can be programmed as “One Time Codes” or “Codes with Time Limit”. The Visitor Codes
will be cleared automatically after use if they are one time codes, or, when the allowed time
expires.
LOCATION
VISITOR ID
01
-
50
00
or
01
t
en
or
Do
40
VALID PERIOD
(1)
(2)
-
(3)
99
VISITOR CODE
VALIDATION
#
4-8 DIGITS
(4)
(5)
(1) LOCATION
Key in Location 40
(2) VISITOR ID
-
--- 50 Visitor IDs for the 50 visitor codes. They are Two-digit numbers
--- Clear all the Visitor Codes in Location 40. Please see the Programming
example below for the details.
(3) VALID PERIOD
The codes in this box MUST be two digits and they represent the time of operation.
ry
--- One Time Code
One Time Code has no time limit but it can only be used for ONCE. It is cleared after use.
on
--- Time Limit in Hour(s)
The Visitor Code can be set with the valid time limit of 1 Hour to 99 Hours with a two-digit
number of 01 to 99. The visitor code is cleared when the time limit reaches.
lin
(4) VISITOR CODES
eL
The Visitor Codes can be 4-8 digits for Manual Mode code entry.
The Visitor Codes MUST be in the same digit length with the Master Code for Auto Mode code entry.
The Visitor Codes can not reset Duress Output.
When a new Visitor Code is put in the same Code box, the old code is replaced.
NOTE: All Visitor Codes will be cleared after power down to prevent extension/confusion of
their valid time limit.
22
td
(5) VALIDATION
Press
key once. Two-beeps confirms the entry.
EXAMPLES:
Example 1: Set a “One Time Visitor Code” with the number of “1 2 6 8” for the Output 1
(b)
(c)
(d)
t
en
or
Do
(a)
(e)
(a) Visitor Code Programming, (b) The Visitor ID, (c) An One Time Code, (d) The Visitor Code, (e)
Entry Confirmation
Example 2: Set a “Visitor Code” with the number of “1 3 7 8” that is valid for three hours
(a)
(b)
(c)
(d)
(e)
(a) Visitor Code Programming, (b) The Visitor ID, (c) Valid for 3 Hours, (d) The Visitor Code, (e)
Entry Confirmation
Example 3: Delete a “Visitor Code” from Vistor ID 02 in the memory
(a)
(b)
(c)
(a) Visitor Code Programming, (b) The Visitor ID, (c) Delete Confirmation
ry
Example 4: Clear all “Visitor Codes” in Location 40
(b)
(c)
on
(a)
(a) Visitor Code Location, (b) The Deletion Command Code, (c) Confirmation, all Visitor Codes are
cleared
lin
td
eL
23
DURESS CODES (FOR OUTPUTS 1 & 2)
(Locations 41 & 42)
Duress Codes are prepared for those Important Persons in case of DURESS while he is operating
the access control keypad. The duress code operates like a normal User Code for Output 1 or 2, and
at the same time activates the Duress Output without any indication. The user may use it to report
an emergency and ask for help silently when he is forced to operate the keypad if the Duress
Output is connected with a security system (for example, an Auto-dialer).
t
en
or
Do
NOTE: The Duress Codes are always valid. They are not governed by any inhibit or lockup function
in the system.
LOCATIONS
-
41
(1)
42
CODE ID
01
-
(2)
50
DURESS CODE
VALIDATION
4-8 DIGITS
#
(3)
(4)
(1) LOCATIONS
– Duress Codes for Output 1
– Duress Codes for Output 2
(2) DURESS CODE IDs
50 Duress Code IDs for The Output 1
-
10 Duress Code IDs for The Output 2
Clear all the Duress Codes from the selected Location group.
Please see the programming example below for the details.
on
0999 =
ry
-
lin
(3) THE DURESS CODES
50 and 10 Duress Codes can be programmed for Output 1 and 2 respectively. They are stored in
their two-digit Code ID box. When a new Code is put into the same Code ID box, the old code is
replaced.
(4) VALIDATION
Press
key once. Two-beeps confirms the entry.
24
td
eL
The Duress Codes are 4-8 digits for Manual Mode code entry.
The Duress Codes MUST be in the same digit length with the Master Code for Auto Mode
code entry.
Always set a Duress Code that is easy to remember in Panic Situation. Only one number
different from the daily used User Code is highly recommended.
Example: User Code is 1 3 6 9, then 3 3 6 9 or 1 3 6 0 might be a good choice for the
Duress Code.
EXAMPLES:
Example 1: Set a “Duress Code” with the number of “3 3 6 9” for Output 1
(a)
(b)
(c)
(d)
(a) Duress Code for Output 1, (b) Duress Code ID, (c) The Duress Code, (e) Entry Confirmation
t
en
or
Do
Example 2: Set a “Duress Code” with the number of “2 3 9 8 0” for Output 2
(a)
(b)
(c)
(d)
(a) Duress Code for Output 2, (b) Duress Code ID, (c) The Duress Code, (e) Entry Confirmation
Example 3: Delete an Output 1 “Duress Code” from Duress Code ID
(a)
(b)
01 in the memory
(c)
(a) Duress Code for Output 1, (b) The Duress Code ID, (c) Delete Confirmation
Example 4: Clear The Whole Group of Duress Codes from Location
(a) Group Location
in Location
(b)
(c)
ry
(a)
41 :
, (b) The Group Deletion Command, (c) Confirmation, all Duress Codes
are cleared.
on
OPERATION AND FUNCTION OF THE DURESS CODE
lin
eL
The Duress Code(s) has double actions when it is keyed in. It activates the Duress Output (for duress
alarm) and at the same time activates the specific Relay Output 1, 2 or 3 just like a normal User Code.
The Duress Code always activates the Relay Output in its group, but, does not de-activate (stop) the
Duress Output. ONLY a normal User Code in anyone of the user groups, or a Super User Code
can reset (de-activate) the Duress Output.
For Example:
Key in The Duress Code 3 3 6 9 of the Group 1 (for Output 1) To Command The Duress Function :
----- Duress Output activates (switches to (-) ground) & Output 1 activates.
td
Key in The Duress Code 3 3 6 9 in Group 1 (for Output 1) Again :
----- Duress Output keeps activating and no change in its state (keeps to (-)
ground) & Output 1 activates again.
Key in A Normal User Code to Reset Duress (For Example: 1369 is An User Code for Output 1):
----- Duress Output resets (back to OFF state) but does not activate Output 1.
25
OUTPUT MODE & TIMING FOR OUTPUT 1 and 2
(Locations 51 & 52)
The two relay outputs are programmable for Start/Stop or Timing modes. Apart from door access
control, alarm arm-disarm control, they are also universal timers for automatic operators in
industry with their 99,999 seconds (over 24 hours) programmable timer.
LOCATIONS
51
-
52
OUTPUT MODE & TIME
0
1 - 99999
t
en
or
Do
(1)
or
VALIDATION
#
(2)
(3)
(1) LOCATIONS
-- Location for Output 1
-- Location for Output 2
(2) OUTPUT MODE & TIMING
Start /Stop Mode (Toggle)
The number 0 sets the output to Start / Stop mode. The output Starts when an User Code is
entered; the output Stops when an User Code is entered again.
-- Seconds Momentary --- (Default -- Momentary 5 Seconds)
ry
The output can be set in Momentary Mode with the time of 1 second to 99,999 seconds. The
output will reset automatically when the time expires.
Press
on
(3) VALIDATION
key once. Two-beeps confirms the entry.
lin
RESET OUTPUT TIMER WITH SUPER USER CODE
The Output Timer can be RESET manually at anytime with the Super User Code that operates
the desired output before the end of the time.
eL
Example:
Reset Output 1 Timer --
SUPER USER CODE
------------- Output 1 stops
Reset Output 2 Timer --
SUPER USER CODE
------------- Output 2 stops
td
26
SYSTEM REAL-TIME-CLOCK
(Location 55)
This 24 hour real-time-clock provides the daily time base for starting and stopping the function of
inhibition to relay output 1 (mainly for electric door lock strike).
No real-time-clock setting is required if daily start-stop inhibition at Location 56 is not
enabled.
LOCATION
CURRENT REAL TIME
t
en
or
Do
55
(1)
(1) LOCATION
Key in Location
HH
VALIDATION
MM
HOURS
#
(3)
MINUTES
(2)
55
(2) CURRENT REAL TIME
H HM M
– The current time in Hour and Minute. The allowed time figure is 00:00 – 23:59
The time setting is based on 24 hours daily with the first two digits for hours and the last two digits
for minutes. The time in second always starts at 0 0.
(3) VALIDATION
Press
#
key once.
Programming Examples:
ry
Two-beep confirms the setting and the clock starts to count in 24 hour basis from the programmed
current time.
55 1030 #
b) Set the current time of “6:45” (PM) to the keypad ------ 55 1845 #
lin
on
a) Set the current time of “10:30” (AM) to the keypad ----
eL
IMPORTANT NOTE:
1) The real-time-clock stops after power failure, which makes the real-time inhibition loses
its time base. It is necessary to re-program the system’s real-time-clock unless the
keypad is back up with UPS.
2) The keypad gives warning beeps of 3 fast beeps / 5 seconds continuously after
power failure until the real-time-clock is re-programmed.
td
3) No “after power failure warning beep” will be given if Location 56 is not programmed
with Start/Stop times.
4) Suggest to program the clock every 3-6 months to keep time accuracy; or when time
deviation is found.
27
START & STOP TIMES FOR DAILY INHIBITION OF OUTPUT 1
(Location 56)
Setting with start and stop times into the keypad, the real-time inhibition period for output 1 will
recycle daily until the time settings are cleared.
This function works with the real-time-clock. Set up the real-time at Location 55 is necessary.
For safety reason, the Egress Button is designed always valid. The door lock (controlled by output
1) can be opened with it at anytime during inhibition.
t
en
or
Do
LOCATION
HH
56
(1)
(1) LOCATION
Key in Location
STOP TIME
START TIME
HOURS
MM
MINUTES
(2)
HH
HOURS
VALIDATION
MM
#
(4)
MINUTES
(3)
56
(2) START TIME
HH MM
– Set the real-time inhibition starting time in Hour and Minute. The allowed time
figure is 00:00 – 23:59
(3) STOP TIME
HH MM
on
ry
The starting time is based on 24 hours daily with the first two digits for hours and the last two digits
for minutes. The time in second always starts at 0 0.
– Set the real-time inhibition stopping time in Hour and Minute. The allowed time
figure is 00:00 – 23:59
lin
The stopping time is based on 24 hours daily with the first two digits for hours and the last two digits
for minutes. The time in second always starts at 0 0.
(4) VALIDATION
#
key once.
eL
Press
Two-beep confirms the setting.
td
28
Programming and Operation Examples:
(i) Set the starting and stopping time for the real-time inhibition period
a) Set Inhibition Period from 12:30 PM (today) – 1:30 PM (same day) for lunch time:
56 1230 1330 #
b) Set Inhibition Period from 6:30 PM (today) – 8:15 AM (next day) for office close:
t
en
or
Do
56 1830 0815 #
NOTE:
1) The start and stop time figures are 24 hours basis. They are 4-digit figures from the smallest
00:00 to the largest 23:59.
2) Entry of the two figure values from Small (Start) to Large (Stop) for the period of inhibition; the
inhibition will start and stop in the same day. See example (a).
3) Entry of the two figure values from Large (Start) to Small (Stop) for the period of inhibition; the
inhibition will start at the time of the day; thus stop in the next day. See example (b).
4) The keypad does not accept the “Start” and “Stop” times with same value. The two time figures
must be different.
ry
(ii) Clear the function of inhibition
Clear the time settings to stop the function of inhibition:
on
56 #
(iii) Pause the real-time inhibition manually
lin
The real-time inhibition can be stopped temporarily if require; such as the staff work overtime in
office. The inhibition can be paused manually with Super User Code before or during the
inhibition period. The pause is toggle and does not affect the real time period counting.
#8
---- Inhibition paused [Inhibit LED(Red) Flashing]
Super User Code
#8
---- Inhibition resumes [Inhibit LED(Red) ON]
eL
Super User Code
NOTE:
The “INHIBIT” LED(Red) is flashing during the paused period; and it is ON after inhibition resumes.
td
(iv) Open door lock with Super User Code at anytime
The Super User code is valid all the time even in the inhibition period. This function does not
affect the real time period counting.
Super User Code
#1
---- The door is open
29
PERSONAL SAFETY AND SYSTEM LOCK-UP
LOCATION
60
(Location 60)
LOCK-UP OPTIONS
VALIDATION
#
1 to 2 Digits
(1)
(2)
(3)
(1) LOCATION
60
t
en
or
Do
Key in Location
(2) LOCK-UP OPTIONS
The Options are represented by the following Numbers. They are described below:
1 --- After 10 successive false User Code trials, the keypad locks during 60 seconds.
-- (Default)
2
--- After 10 successive false User Code trials, activates the Duress output to switch to (-)
ground.The Duress Output can be released with any user Code in the User Group 1 or Super
User Code.
5
-
10
---
Selection of after 5 to 10 successive User Code trials, the keypad locks during
15 minutes. The keypad can be reset to release the lock-up with the “Super User
Code” in the following way.
30
SUPER USER CODE
ry
Example: Release the lock-up --
00 --- Disappearance of all the above lock-up securities.
Press
on
(3) VALIDATION
key once . Two-beeps confirms the entry
lin
td
eL
30
USER CODE ENTRY MODE – Auto or Manual
(Location 70)
LOCATION
70
(1) LOCATION
Key in Location
ENTRY MODES
70
1
(1)
or
(2)
VALIDATION
2
#
(3)
t
en
or
Do
(2) USER CODE ENTRY MODES
Two modes 1 and 2 are available for User Code entry options.
1 --- Auto Entry Mode
Auto Entry Mode requires no pressing of the # key after code entry for code checking.
In the Auto Entry Mode, the User Codes MUST be set in the same digit length of the Master
Code (For example, if the Master Code is 5 digits, then all User Codes must be in 5 digits as well.
All other User Codes not in 5 digits become invalid). When the number of digits reaches, the system
will check the User Code automatically. Good for high traffic access control.
2 --- Manual Entry Mode – (Default)
Manual Entry Mode always requires the # key following the User Code for code checking. The User
Codes can be 4-8 digits arbitrary and they are NOT required to be in the same digit length of the
Master Code. Manual Entry increases the level of security in code trial by the unauthorized people.
on
ry
(3) VALIDATION
key once . Two-beeps confirms the entry
Press
PACIFIER TONES ON-OFF SELECTION
LOCATION
71
71
1
(1)
or
(2)
0
VALIDATION
#
(3)
lin
(1) LOCATION
Key in Location
FUNCTION MODES
(Location 71)
eL
(2) FUNCTION MODES FOR PACIFIER TONES
Pacifier Tone is the Beep Tones from the keypad, which include the tones of Successful Key entry
(1 beep) and the Unsuccessful User Code entry (5 beeps).
NOTE:
The beeps for the Warning and the Power-up Delay do not belong to pacifier tones and can not be
OFF.
1 --- Pacifier Tone ON – (Default)
td
All the Pacifier Tones available from the keypad are enabled. They are the response tones
indicating the operation status of the keypad after a User Code is entered.
0 --- Pacifier Tone OFF
All the Pacifier Tones are OFF. Good for place needs for a silent environment.
(3) VALIDATION
Press
key once. Two-beeps confirms the entry
31
OUTPUT OPERATION ANNOUNCER
(Location 72)
LOCATION
(1) LOCATION
Key in Location
FUNCTION MODES
72
72
1
(1)
VALIDATION
0
or
(2)
#
(3)
t
en
or
Do
(2) FUNCTION MODES FOR OUTPUT ANNOUNCER
Output announcer gives notification beep on the operation status of the outputs. There are two
notification modes available for the selection.The notification is also OFF while the Pacifier Tone OFF
mode in the Location 71 is selected.
NOTE:
In multi-station operation, the output announcer only goes to the keypad that has been operated but
not all the keypads in the system.
--- No Notification
The output operation notification is OFF but does note affect the normal pacifier tones.
--- 1 Second Long Notification -- (Default)
1 second notification beep is given when the output relay activates. It is prepared to notify the
person outside the door when the lock is released and the door can be opened. It is good for door
lock that gives no sound when it activates, such as a magnetic lock.
2
ry
--- 2 Short Beeps Notification
2 short beeps notification is given when the output relay activates.
(3) VALIDATION
key once . Two-beeps confirms the entry
Press
on
STATUS LED FLASHING ON-OFF DURING STANDBY
(1) LOCATION
Key in Location 73
FUNCTION MODES
VALIDATION
lin
LOCATION
(Location 73)
73
1
(1)
or
(2)
0
#
(3)
eL
(2) FUNCTION MODES FOR STANDBY FLASHING LIGHT
Some people find the flashing light of the status LED (the amber LED) is annoying during standby,
especially at the night time. The standby flashing can be ON-OFF with the setting here.
1 --- Standby Flashing ON -- (Default)
0
--- Standby Flashing OFF
The Standby Flashing is OFF but it does not affect the system status indications.
(3) VALIDATION
key once . Two-beeps confirms the entry
Press
32
td
The Status LED gives Standby Flashing all the time. It also gives the light indications showing the
operation status of the system.
DOOR FORCED OPEN WARNING & TIMING
(Location 80)
LOCATION
80
(1) LOCATION
Key in Location
FUNCTION MODES
0
(1)
or
1
(2)
VALIDATION
999
#
(3)
80
t
en
or
Do
(2) FUNCTION MODES FOR DOOR FORCED OPEN WARNING
The Door Forced Open Warning function works with a Door Position Sensing switch equipped on the
door (usually a magnetic contact). Once a Timing Figure is put into the Function Mode box, the
warning mode is enabled.
0 --- Door Forced Open Warning OFF – (Default)
1 - 999 --- Door Forced Open Warning & Timing
The Timing Figure for the Warning can be 1-999 seconds. The keypad generates the door forced
open warning beeps instantly if the door is forced to open without a valid User Code or pressing of
Egress Button. The beeps will last as long as the time set on the timer and it can be stopped at
anytime with an User Code in Group 1 before the end of the time.
The Manner of The Door Forced Open Warning:
a) The door is forced to open (without using Code or Egress Button) – Warning
b) The door is opened with Code – No Warning
c) The door is opened with Egress Button – No Warning
Press
ry
(3) VALIDATION
key once . Two-beeps confirms the entry
on
DOOR PROPPED-UP WARNING & THE DELAY TIME
LOCATION
(1)
(1) LOCATION
Key in Location
0
81
or
1
-
999
VALIDATION
lin
81
FUNCTION MODES
(Location 81)
(2)
#
(3)
0 --- Door Propped-up Warning OFF – (Default)
1 - 999 --- Door Propped-up Warning ON & The Delay Time
td
eL
(2) FUNCTION MODES FOR DOOR PROPPED-UP WARNING
If somebody opened the door and left it open longer than the allowable delay time, the keypad will
generate door propped-up warning until the door is re-closed. There is warning beeps from the
keypad only but it does not activate the alarm output. This function works with a door position
sensing switch equipped on the door.
The Delay Time can be 1 to 999 seconds. It is the allowed time for door open without starting
warning.
(3) VALIDATION
Press
key once . Two-beeps confirms the entry
33
INTELLIGENT EGRESS BUTTON – AN UNIQUE FEATURE OF THE KEYPAD
INTRODUCTION
t
en
or
Do
Most of the keypads for access control are just for controlling “Going In” from outside. It is not
enough for today’s access control systems. In fact, controlling “Going Out” is also very important in
some public passage areas those are not allowed to use locks or digital keypads for stopping of
“Going Out” due to safety reasons. Such as hospitals, kindergartens, elderly homes, convenient
stores, emergency exits etc.. The wardens, teachers, shopkeepers and the guards are always
required to keep an eye on people to prevent unattended leaving, shoplifting, and unauthorized use
of the emergency exits.
The Intelligent Egress Button can be programmed to do something to get attention from the person
on duty before the door is opened. The button offers programmable egress delay, delay with
warning, holding button for the delay, momentary button contact with warning for the delay and
even gives alarm when a controlled door is opened.
Locations 90 is the place for setting the desired functions for the Egress Button.
The functions programmed to the Egress Button do not affect the normal operation of the keypad.
The operation of the keypad with Code is always in the first priority to give instant action to the
output relay 1 for door strike.
It is NOT required to program the Egress Button with the special function in normal use. Just leave
it on its default values.
Hospital:
ry
WHERE AND WHY “GOING OUT” NEEDS ATTENTION
Examples for some areas may need an Intelligent Egress Button:
lin
Kindergarten:
on
Some of the patients are not allowed to leave the ward without doctor’s permission. An egress
button with exit delay and warning beeps will help the nurse or warden to get attention to the door
when the egress button is pressed. Further setting of the egress button with holding contact delay
even gives higher level of security to a controlled door.
eL
Young children are always active. Some of them may be willing to go out to explore their ways of
playing. For safety reason, teachers have to watch all of them in the attended area. Leaving school
alone without the companion of parents or teacher is dangerous to young children. An egress button
with delay and warning beeps will be helpful to prevent the children trying to go out without getting
the attention of the teacher.
Elderly Home:
The elderly needs constant attention and care. Some old people have poor memory. They may forget
the way to come back if they leave home alone. An egress button with delay and warning beep will
easily get the attention of the warden before the door is open.
td
Convenient Store:
Most of the convenient stores have just only one or two shopkeepers on duty. They are usually the
cashier. Shoplifting may easily happen while the shopkeeper is busily serving customers at the
cashier desk. A holding contact egress button with delay and warning beeps may help to stop most
of the shoplifting. As the thief knows that he is gotten attention by the shopkeeper before the door
is open.
34
High Traffic Passage:
A short buffer time may be necessary for opening a door outward after pressing the egress
button for those exits open to a high traffic passage. An egress button with short delay and
warning beeps helps the user to pay attention to the people passing by to prevent hitting them
when the door is pushed outward.
t
en
or
Do
Emergency Exit:
Emergency Exit is not open to the public for daily use. It is for emergency case only. It is usually
closed and watched by guards. The egress button of this keypad can be programmed to offer
exit delay with warning beeps and even gives alarm output to trigger an alarm system when the
door is forced to open or the door is open after the exit delay expired. It is an useful tool to get
attention of the person on duty.
WARNING
Do not enable Egress Delay if instant door open for leaving is the main
concern in your area.
Make sure the Egress Delay does not affect the safety in your service
area before enabling the function in Location 90.
ry
The default setting of the system is NO DELAY.
lin
on
td
eL
35
EGRESS DELAY , WARNING AND ALARM
LOCATION
CONFIGURATIONS
90
1
(1)
(2)
DELAY TIME
5
0
or
1
(3)
99
VALIDATION
#
(4)
90
t
en
or
Do
(1) LOCATION
Key in Location
(Location 90)
(2) CONFIGURATIONS OF THE EGRESS WARNING
Key in the number to enable 1 of the 6 configurations described below:
1 --- Momentary Contact Mode without Warning -- (Default)
Press the Button once. No warning or alarm is given during Egress Delay.
Good for silent area. The people have to wait for the door open until the delay time reaches.
2 --- Momentary Contact Mode with Warning Beep
Press the Button once. The system gives Warning Beeps during the Egress Delay.
Good for the place required attention. The keypad beeps during the people are waiting for the
door open.
4 --- Holding Contact Mode without Warning
on
ry
Press and hold the Button. No warning or alarm is given during the Egress Delay.
Good for the silent area. The people require to press & hold the button until the delay time
reaches for the door open.
5 --- Holding Contact Mode with Warning Beep
Press and hold the Button. The system gives Warning Beeps during Egress Delay.
Good for the place required attention. The keypad beeps while the button is kept pressed during
the people are waiting for the door open.
lin
(3) EGRESS DELAY TIMER
0 --- No Delay – (Default)
eL
Output 1 activates instantly (the door is released instantly) when the Egress Button is pressed.
1 – 99 --- Egress Delay Timing
Put a number of 1 to 99 into the box to enable the Egress Delay. The number is the time in second, which
starts to count when the Egress Button is pressed. Output 1 activates (the door is released) when the delay
time reaches.
td
36
NOTE:
1) Momentary Contact -- The Egress Delay starts to count when the egress button is momentarily
pressed. Output 1 activates automatically (door is released) when the delay time reaches.
2) Holding Contact -- The user MUST hold the egress button in contact for the whole period of the
Egress Delay time until Output 1 activates. If the egress button is released before the end of the
Egress Delay, the timer will stop to count and reset.
t
en
or
Do
For safety, it is necessary to put a sticker next to the egress button telling how to open the
door if “Holding Contact” is enabled.
Example: A sticker for an egress button that is programmed with “Holding Contact” of 5 seconds.
Press & Hold The Button
5 Seconds Minimum
Until The Door Is Open
3) The Egress Delay does not affect the operation of the User Codes for Output 1. The User
Codes always give INSTANT action.
(4) VALIDATION
Press
key once . Two-beeps confirms the entry
ry
EXAMPLES:
Example 1: Set Egress Button in Momentary contact of 5 seconds with delay & warning beep
(b)
(c)
(d)
on
(a)
(a) Egress function programming, (b) Momentary contact with warning, (c) Delay time of 5 seconds
to release door, (d) Entry confirmation
(a)
(b)
lin
Example 2: Set Egress Button in Holding contact of 10 seconds with warning beep
(c)
(d)
eL
(a) Egress function programming, (b) Holding contact mode with warning, (c) Holding time of 10
seconds to release door, (d) Entry confirmation
Example 3: Set Egress Button in Momentary contact without delay (This is the default setting)
(a)
(b)
(c)
(d)
td
(a) Egress function programming, (b) Momentary contact without delay, (c) Release door instantly,
(d) Entry confirmation
37
OPERATION MODES
(Location 94)
The keypad is programmable for keypad mode to work stand-alone for door control directly or for
server mode to work with a split-decoder for high security access control.
LOCATION
OPERATION MODES
94
VALIDATION
0 or 1
(1)
#
(3)
t
en
or
Do
(2)
(1) LOCATION
Key in Location 94
(2) OPERATION MODES
– Keypad Mode (Default)
Keypad Mode sets the keypad for stand-alone operation to provide its available functions. It is
compatible with the auxiliary readers/keypads for multi-station expansion.
– Server Mode
Server Mode sets the keypad to compatible with both the decoder for split-decoded operation and
the auxiliary readers/keypads for multi-station expansion. A split decoded keypad system uses the
keypad(s) for human interface outside and the internal decoder for door lock control to prevent
sabotage.
ry
(3) VALIDATION
Press
key once. Two-beep confirms the entry
lin
on
CLOSE PROGRAMMING MODE
(**)
Always close programming mode with * * to set system back to normal Operation after
programming.
eL
VALIDATION
------------------------------- System is back to normal operation mode
td
38
PROGRAMMING MAKE SIMPLE – For General Users
This is a multi purpose keypad. It has many functions for user’s selection. For those general users
taking the keypad for door strike only, most of the features can be kept in their Default values. Only
the User Codes and a private Master Code are required to program.
PROGRAMMING
t
en
or
Do
NOTE:
a) Wait 1 minute until the end of power up delay, or keyin
instantly and set the keypad to normal operation.
12#
to stop the power-up delay
1) Set System in Programming Mode with The Factory Set Master Code 0 0 0 0
0000
**
---- 2 beeps, system is in Programming Mode
Note: If the Master Code is forgotten, use the DAP Code to set the system into programming mode.
See DAP CODE 2828 in page 14 for the details.
2) Change The Factory Set Master Code to Owner’s Private Master Code for Security Reason
01
3289
#
---- 2 beeps, 3 2 8 9 is a Master Code for example here only.
It replaces the old master code 0000.
ry
3) Set an “User Code” to Operate The Output 1 for Door Open
(a)
2 001
(b)
(c)
8321
(d)
#
on
10
(e)
lin
(a) 10 = Programming Location for Output 1
(b) 2 = Programming option for User Code only
(c) 001 = One of the 1,000 User IDs for the User Code from 000-999
(d) 8321 = The User Code for door open. It is for example here only
(e) # = Confirm the User Code, 2 beeps
eL
REMARK:
If more User Codes are required for Output 1, repeat the procedures (3) above with other User IDs,
such as 002, 003, 004 --- 999 etc. Total 1,000 users are allowed. See Programming Location 10 for
the details.
4) Close The Programming Mode
td
---- 2 beeps
The programming mode is closed. The keypad is back to normal operation mode
OPERATION
5) Open The Door with User Code
--- 2 beeps, the door is open
39
PROGRAMMING SUMMARY CHART
LOCATION
FUNCTION
ENTRY LIMITS & CODE
OPTIONS
01
Master Code
4-8 Digits
02
Super User Code
4-8 Digits
01
02
t
en
or
Do
CODE 1 - MEDIA:
2---Private User Code
5---Deletion of User Code
10
User Codes for O/P 1
FACTORY
DEFAULT
CODE ENTRY
#
MASTER CODE
NIL
#
SUPER USER CODE
NIL
10
CODE1
CODE2
CODE3
#
NIL
20
CODE1
CODE2
CODE3
#
NIL
40
CODE1
CODE2
CODE3
#
NIL
CODE 2 - USER ID:
000-999---Group 1(10)
001-100---Group 2(20)
20
User Codes for O/P 2
CODE 3 - USER CODES:
4-8 Digits
CODE 1 - VISITOR ID:
01-50
40
Visitor Codes
CODE 2 - VALID PERIOD:
00---One Time
01-99 Hours
41
Duress Code for O/P 1
ry
CODE 3 - VISITOR CODE:
4-8 Digits
CODE ID - O/P 1: 01-50
41
CODE ID DURESS CODE
#
NIL
#
NIL
CODE ID - O/P 2: 01-10
on
42
Duress Code for O/P 2
DURESS CODE: 4-8 Digits
42
51
O/P Mode for O/P 1
51
O/P MODE & TIME
#
5 Seconds
52
O/P Mode for O/P 2
OUTPUT MODE & TIME:
0--- Start / Stop
1---99999 Seconds
52
O/P MODE & TIME
#
5 Seconds
55
Real-Time-Clock
56
Start & Stop Times
for Inhibition
56
STOP TIME:
00:00-23:59
LOCK-UP CODE:
1---10 Trial, Lock-Up 60 Sec.
2---10 Trial, Activates Duress
5-10---5-10 Trial, Lock-Up 15
Minutes
00---No Lock-Up
ENTRY MODE:
1---Auto Mode
2---Manual Mode
40
#
CURRENT TIME
START TIME
STOP TIME
NIL
#
NIL
60
LOCK-UP CODE
70
ENTRY MODE
#
#
Code = 1,
10 Trials,
Lock-Up 60
Seconds
td
Code Entry Mode
55
eL
70
START TIME:
00:00-23:59
lin
60
Personal Safety &
Lock-Up
CURRENT REAL TIME:
00:00-23:59
CODE ID DURESS CODE
Mode =
2, Manual
Mode
Pacifier Tone ON-OFF
71
72
Output Announcer
73
Standby LED Flashing
FUNCTION MODE:
0---OFF
1---ON
71
81
Propped-up Warning &
Time
90
Egress Delay Warning
#
Mode = 1,
Pacifier Tone
ON
FUNCTION MODE:
0---NO Notification
1---1 Second Long Beep
2---2 Short Beeps
72
FUNCTION MODE
#
Mode = 1
1 Second
Long Beep
FUNCTION MODE:
0---OFF
1---ON
73
FUNCTION MODE
#
Mode = 1,
Flashing ON
#
Mode = 0,
Door Forced
Open
Warning OFF
#
Mode = 0,
Propped-up
Warning OFF
#
Mode = 1
Momentary,
No warning
TIME = 0
No Delay
t
en
or
Do
80
Door Forced Open
Warning & Time
FUNCTION MODE
FUNCTION MODE / TIME:
0---OFF
1-999 Seconds
CODE 1 - FUNCTION
MODE:
1---Momentary, No warning
2---Momentary, with
warning
4---Hold Contact, No
warning
5---Hold Contact, with
warning
80
FUNCTION / TIME
81
FUNCTION / TIME
90
CODE 1
CODE 2
CODE 2 - DELAY TIME:
0---No Delay
1-99 Seconds
1---Server Mode
FUNCTION
CODE ENTRY
Factory Set Master Code for User to set
system in programming Mode at the first
time.
OR
THIS IS NOT A PERMANENT SYSTEM
NEW MASTER CODE
CODE & IT IS CHANGED IF A NEW
MASTER CODE IS PROGRAMMED.
9999 #
2828
DAP CODE-- Direct access to
programming mode. Valid only in the
power-up delay period
2828 #
LOCATIONS:
10--- User Group 1
20--- User Group 2
40--- Vistor Group
41--- Duress Group 1
42--- Duress Group 2
Exit Programming Code
LOCATION NO.
**
41
All programmed
data are cleared
and back to the
default values
except the Master
Code
System in
Programming Mode
0999 #
td
USER Codes whole group clearing Code
for the selected Location
**
System in
Programming Mode
eL
REFRESH CODE -- Refresh the system
and set all its function back to default
values.
**
RESULTS
0000 * *
9999
0999
Mode = 0
Keypad
Mode
MODE#
lin
0000
94
on
SYSTEM
CODES
ry
Operation Mode
94
FUNCTION MODE:
0---Keypad Mode
Whole group
of users in the
selected location
are cleared
The system back
to normal opration
after programming
APPLICATION EXAMPLES
1) STAND ALONE DOOR LOCK
t
en
or
Do
K301A
ELECTRIC LOCK
NOTE:
Connect the 1N4004 as close as possible to the lock in parallel with the lock power terminals of the
lock to absorb the back EMF to prevent it from damaging the keypad. The 1N4004 is not required
if the electric lock is AC operated.
To avoid Electro-Static-Discharge from interfering with the operation of the keypad, always ground
the (-) terminal of the keypad to earth.
ry
Always connect DOOR SENSOR terminal to (-) ground if not used.
1
3
4
5
6
7
8
9
on
DK-2851
2
(+) (–)
12-24V
OUTPUT 1
OUTPUT 2
EG
N.C. COM N.O. N.C. COM N.O. IN
lin
td
eL
42
2) INTER-LOCK SYSTEM USING TWO KEYPADS
K301A
t
en
or
Do
K301A
An inter-lock system needs two door controllers. This application example uses two keypads with
simple cross wire connection on their "Output 1 Inhibit" and "Inter-lock Control Output" terminals.
It is necessary to link up the "(-) GND" terminals of the two keypads as common ground to achieve
the inter-lock logical functions.
lin
on
ry
Use keypad to open the door from outside
Press egress button to open the door from inside
Connect the door magnetic sensors on the doors to monitor their positions
While door 1 is open, then, door 2 is forced to keep close, or vice versa
Use N.O. Relay output for fail-secure lock; and N.C. output for fail-safe lock
Please also see the "NOTE" stated in the Application Example (1)
eL
K301A
K301A
td
EGRESS
BUTTON
(OPEN DOOR
1 FROM
43