PACSystems* RX3i CPU IC695CRU320

GE Fanuc Automation
Operator Interface Products
QuickPanel™ View &
QuickPanel Control
PCMCIA Adapter
IC754PCMCIA001-A
Hardware User’s Guide, GFK-2368
June 2005
GFK-2368
PCMCIA Host Adapter
GFL-002
Warnings, Cautions, and Notes as Used in this Publication
Warning
Warning notices are used in this publication to emphasize that hazardous voltages,
currents, temperatures, or other conditions that could cause personal injury exist in
this equipment or may be associated with its use. In situations where inattention
could cause either personal injury or damage to equipment, a Warning notice is used.
Caution
Caution notices are used where equipment might be damaged if care is not taken.
Note: Notes merely call attention to information that is especially significant to understanding
and operating the equipment.
This document is based on information available at the time of its publication. While efforts
have been made to be accurate, the information contained herein does not purport to cover
all details or variations in hardware or software, nor to provide for every possible contingency
in connection with installation, operation, or maintenance. Features may be described herein
which are not present in all hardware and software systems. GE Fanuc Automation assumes
no obligation of notice to holders of this document with respect to changes subsequently
made.
GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory
with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency,
or usefulness of the information contained herein. No warranties of merchantability or fitness
for purpose shall apply.
QuickPanel is a trademark of GE Fanuc Automation. Any other trademarks referenced
herein are used solely for purposes of identifying compatibility with the products of GE Fanuc
Automation.
©Copyright 2005 GE Fanuc Automation North America, Inc.
All Rights Reserved.
The PCMCIA Adapter has been tested and found to meet or exceed the requirements of
U.S. (47 CFR 15), Canadian (ICES-003), Australian (AS/NZS 3548) and European
(EN55022) regulations for Class A digital devices when installed in accordance with
guidelines noted in this manual.
Note: This Class A digital apparatus complies with Canadian ICES-003.
Note: This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
Note: Any changes or modifications to the product or installation that are not expressly
approved by GE Fanuc Automation could void the user's authority to operate the
equipment under FCC rules.
GFK-2368
PCMCIA Host Adapter
UL Hazardous Locations Information
The following information is for products bearing the UL marking for Hazardous Locations:
WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY
IMPAIR SUITABILITY FOR CLASS I, DIV. 2.
WARNING - EXPLOSION HAZARD - WHEN IN HAZARDOUS LOCATIONS, TURN
OFF POWER BEFORE REPLACING OR WIRING MODULES.
WARNING - EXPLOSION HAZARD - DO NOT CONNECT OR DISCONNECT
EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS
KNOWN TO BE NONHAZARDOUS.
Power, input and output (I/O) wiring must be in accordance with Class I, Div. 2 wiring
methods, Article 501 4(b) of the National Electrical Code, NFPA 70 and in
accordance with the authority having jurisdiction.
For additional agency qualifications, see page 12.
Table of Contents
Table of Contents.................................................................. 4
Introduction ........................................................................... 5
PCMCIA Card Compatibility ................................................. 6
Installing the PCMCIA Adapter ............................................ 9
Agency Qualifications ........................................................ 12
5
Introduction
The PCMCIA Adapter Interface Card can be installed in a GE Fanuc
QuickPanel View or QuickPanel Control operator interface to provide
support for a single Type I, Type II, or Type III PCMCIA card.
The Adapter can be used with GE Fanuc Intermediate and Loaded
QuickPanel View & Control products. The Intermediate and Loaded
QuickPanel models have a built-in expansion connector.
QuickPanel View and QuickPanel Control operating system version
1.04.0047 (and later) includes support for the PCMCIA adapter card.
Operating system versions 1.03.046 (and earlier) must load an updated
driver in order to use the PCMCIA adapter. The updated driver and
installation instructions are available at the GE Fanuc support website
http://globalcare.gefanuc.com/.
GFK-2368
PCMCIA Host Adapter
6
PCMCIA Card Compatibility
The Adapter supports the following types of PCMCIA cards:
-
I/O mapped only cards
-
Memory mapped cards that do not require more than 60KB of
address space.
PCMCIA memory cards used with the PCMCIA Adapter do not require
additional software. However, other types of 3rd party cards may require
card specific drivers to be loaded into the QuickPanel Control or
QuickPanel View. Such required drivers are supplied by the
manufacturers of the PCMCIA card and must be suitable for use with
Windows CE.NET v4.1 and the ARM processor type.
The address mapping or device naming for I/O cards inserted into the
PCMCIA adapter is determined by the manufacturer of the I/O card and
the device driver supplied for the card. For example, a PCMCIA fourport serial expansion card may have the four connectors labeled “1”, “2”,
“3” and “4”. However, on a QuickPanel with a single serial port (COM1),
"1" may be mapped to COM5 on the QuickPanel by the card driver.
7
Device naming for memory cards inserted into the PCMCIA adapter is
determined by the Windows operating system and is insertion-order
dependant. For example, upon inserting a Compact Flash memory card
then inserting a PCMCIA memory card, the Compact Flash card would
be named “PCFlash Storage” and the PCMCIA memory card would be
named “PCFlash Storage2”. If the order of insertion is reversed, the
names will be reversed.
Note:
PCMCIA cards inserted into the adapter may affect overall
system performance of the QuickPanel due to the electrical
requirements of PCMCIA cards and their slower speed
compared to the QuickPanel’s system bus. Computational
intensive applications, continuous 100Mbit Ethernet traffic, or
high COMM data rates may be adversely affected. The extent
of any effect is application dependant and users of the
PCMCIA card are responsible for verifying the suitability of the
card in the QuickPanel with their specific applications.
The PCMCIA adapter supports 5V and 3.3V PCMCIA cards. A PCMCIA
Memory or I/O card can consume up to 3 watts. PCMCIA cards can be
installed and removed with power applied.
GFK-2368
PCMCIA Host Adapter
8
Examples of Compatible PCMCIA Card Types
-
Four-port serial cards
-
Modem
-
ATA (Advanced Technology Attachment) flash cards
-
LAN cards etc.
-
3.3V/5V VCC to PC-Card
The following types of cards are not supported:
-
SRAM cards above 64KB.
-
Linear addressable flash ROM cards above 64KB
-
Old flash ROM cards that require 12V VPP.
-
DMA memory cards.
For a current list of 3rd party cards that have been tested in the
QuickPanel View/Control and found to be compatible, refer to
QuickPanel View, QuickPanel Control, Display-PAC XScale V1.x Third
Party Compatibility, which can be found on
http://globalcare.gefanuc.com.
9
Installing the PCMCIA Adapter
Caution:
Always use anti-static precautions when accessing
the mating connector or the interior of the unit.
Remove power from the QuickPanel before opening
the back cover.
Nylon Screw
GFK-2368
PCMCIA Host Adapter
10
Note:
The 6” QuickPanel is shown. Other models are similar.
Note:
The Adapter consumes 1.041 watts at 24VDC and supports PCMCIA
cards with maximum power consumption of 3 watts. You should verify
that the 24VDC power supply for the QuickPanel product can provide
an additional 5 watts of power to support the power consumption of the
Adapter and PCMCIA card.
1.
Disconnect the DC input power terminal block connector from your
QuickPanel Control unit before installing the Adapter.
2.
3.
Open the back cover of the QuickPanel.
4.
To secure the Adapter in the unit, install the four provided screws
as shown in the figure on page 9.
Attach the PCMCIA Adapter to the unit by plugging the module into
the expansion connectors on the back of the unit.
Caution:
Be sure to properly align pins in the dual connector
upon insertion to avoid damage to the Adapter or the
QuickPanel Control unit.
5.
Tighten the screws until tight and then 1/4 turn of the screw. Do not
over tighten the screws to avoid breaking the screw or board.
Caution:
To avoid damaging a PCMCIA card, install the nylon
screw in the hole between the ejector rails as shown
in the figure on page 9.
6.
Close the cover.
11
General Specifications
Environmental Conditions
Temperature
Operation
Storage
0°C to 60°C
-40°C to 85°C
Humidity
5 to 95% relative humidity (non-condensing)
Vibration (Operating)
(IEC 60068-2-6, JISC0911)
10 - 57Hz, 0.012" peak-peak displacement
57 - 500Hz, 1.0g acceleration
Shock (Operating)
(IEC 60068-2-27, JISC0912)
15g, 11ms (sine wave)
Power consumption
Adapter
PCMCIA Memory or
I/O card
GFK-2368
1.041 watt
3 watts maximum
Note:
The 24 VDC power supply for the
QuickPanel must be able to provide an
additional 5 watts to support the power
consumption of the Adapter and PCMCIA
card.
PCMCIA Host Adapter
12
Agency Qualifications
Description
N.A. Safety for Industrial Control
Equipment
Agency
Standard or
Marking
UL508/C-UL
N.A. Safety for Hazardous Locations
Class I, Div. 2, Groups A, B, C, D
UL1604/C-UL
Explosive Atmospheres Directive
European Safety for Hazardous
Locations
Equipment Group II, Category 3
ATEX
Electromagnetic Compatibility
Directive
European EMC for Industrial Control
Equipment
CE
Comments
Certification by Underwriter's
Laboratories to UL standard
and equivalent CSA standard
Certification by Underwriter's
Laboratories to UL standard
and equivalent CSA standard
Certification in accordance
with European Directives;
Refer to Declaration of
Conformity and Independent
rd
3 Party Assessment
Certificate
Certification by Competent
Body in accordance with
European Directives; Refer to
Declaration of Conformity