Bird-X BXP-PRO-2 Bird Xpeller Pro Sonic Bird Repellent Manual

HIGH will increase sound output.
CAUTION: Take care when turning the dial since the unit may be in
an inactive state when the dial is rotated. It could then reactivate at
a very high level of sound which could be painful to your ears.
POWER SWITCH (NT/EXT, SPKR)
The power switch enables the unit to operate.
Slide the switch to the INT/EXT. SPKR (ON)
position to start the unit. This will operate the unit,
and generate sound out of the unit AND out of an
optional extension speaker at the same time. If
you wish to operate ONLY a remote extension
speaker (optional), then move the switch to the
EXT. SPKR ONLY position.
If you turn the unit OFF, be sure to leave it off
for about 30 seconds before turning it back on to
allow the electronics to properly reset. To fully
disconnect the unit, unplug the power adapter from
the electrical outlet or disconnect the battery cable
from the 12-volt battery.
IRQUBLESHOOTING —
PROBLEM | SOLUTION
« Check volume settings
Unit is on, * Check time of operation settings.
* Check that at least one bird is
selected to play.
but no sound is heard
Unit is on, but plays the
same bird over and over,
regardless of settings
* Reset the unil by turning it off for
30 seconds and then back on.
* Double check Mode switch
settings
Unit is not operating » Make sure photocell is not
properly in the obstructed.
DAY or NIGHT mode » Make sure the photocell is not
affected by bright lights in either
the front or the back of the unit.
; : « Check battery condition
Unit does not function Y 3
* Turn power switch on the unit to
properly when connected the OFF position. Reconnect the
battery, wait 30 seconds, then
to a 12 volt battery switch the unit back on
Limited Warranty
This BirdXPeller Pro Unit is warranted against
defects in material and workmanship for six months
from date of purchase (extended warranty available).
Bird-X will replace or repair, provided defect occurs
under normal use. Returns accepted only authoriza-
tion from our Chicago office.
Successful Long-Term Behavior Modification
Product success takes time to build. Bird and pest habits
may take several days or weeks to break. Follow all
suggestions for maximum efficacy. "Instant" tests do not
replicate natural conditions and give no indication of the
unit's success with the infestation.
Prepare for Successful Bird Control
Bird-X, Inc. has been recognized worldwide as the bird
control x-perts for 40 years. We have become experts
through extensive experience and research. As a
result, we are happy to analyze problems and make
reommendations based on each customer's specific
situation and needs. In addition, we provide the following
recommendations for greatest success, even before
activating the repeller.
Remove inducements. Clean the area of all evidence
of birds: nests, fledglings, droppings, dead birds, and
the residential scent. Because birds and their droppings
can carry many diseases, use extreme caution when
removing them. Do not breathe or come into direct
contact with them. If you have questions about how to
do this safely, consult an expert. (Adult birds are likely
to return to their young in order to protect them or to
assist them in leaving the area.) Remove food spillage,
garbage, nesting material and other appealing items.
Survey the birds to determine flight and time patterns,
entries and exits, and nesting, feeding and roosting
habits. This will suggest the unit placement, speaker
direction and time of operation you should choose. Make
educated guesses as to where the birds will go when they
are repelled from their current infestation, and consider
additional units to cover these alternative areas.
Maintain a clean and changing environment. Periodically
clean the area of nests and droppings, relocate or
reposition the unit, vary the output, or turn off the unit for
a short time.
Install early, before "bird season” begins, as it is easier to
keep the birds away than to rout them out once they have
established a living pattern.
Use products synergistically. Two or more different
kinds of devices (this repeller plus a visual scare product
and/or a roost inhibiting device) will produce a synergistic
effect -- i.e., in combination, the products will yield much
greater effectiveness than the one alone. Contact us for
information on “companion” products.
BIRDI0» E
Bird-X, Inc.
300 N. Oakley Blvd.
Chicago, IL 60612
312.226.2473 + solutions Qbird-x.com
EPA Est. No. 075130-0R-001
C € BirdXPeller Pro 2 Instructions P/N 655-0050-00 (BXP#2) rev. ©
Digital Bird Repeller
INSTALLATION
Important safety-related information:
a) Do not install the device during rain or snow
conditions.
b) Installation shall be made in such a way that a
power supply and the internal part of the control unit
never be subjected to water or snow.
c) Note that the power supply is intended for dry
location use only.
1)
2)
3)
Point the unit toward the
bird infestation. Expect a
maximum coverage area
of approximately 1 acre ina
long dispersion pattern. Set
the unit on a flat surface or
mount it to a wooden post
using the mounting bracket
and screws (included).
Plug one end of the AC adapter into the POWER
jack (located on the back of the unit). Plug the
adapter into any standard electrical outlet. An
optional battery cable may be used to connect the
control unit to a 12-volt battery. If this is done, first
connect the black battery clip to the negative terminal
on the battery and then connect the red battery clip
to the positive terminal. Both the connection to the
electrical outlet (or battery) and the connection of the
power cable inside the control unit must be protected
from dripping or splashing water. Do not set an
object filled with liquids on the control unit.
Set the DIP switches located on the front metal
faceplate of the unit, (see Switch Array #1 and
Switch Array #2) to the desired settings. See the
section “Programming your BirdXPeller PRO” for
specific programming information.
4) Turn the volume switch to LOW (Minimum).
5) Turn the power switch (located in the upper right
hand corner of the faceplate) to INT/EXT. SPKR (ON
position). (NOTE: The unit may take a couple of
seconds before starting).
6) Adjust the volume to the desired level.
7) After turning the unit OFF, be certain to wait AT
LEAST 60 SECONDS before turning it back on.
8) Close the cover and latch shut. Ensure that the
cover is properly latched closed and do not open
the cover during rain or other conditions that would
expose the inside of the control unit to water.
PROGRAMMING YOUR BIRDXPELLER
RECORDING | TO program your
Switches (1-8)
BirdXPeller PRO unit you
will need a small screw-
driver, toothpick, or other
pointed, rigid object to
move the switches in the
switch array (see FIG.
1). The switch arrays
are the switch banks
located in the bottom right-hand corner on the
faceplate (inside the clear front cover). A switch
is ON if the switch is moved to the right-hand
side. The switch is OFF if the switch is moved
to the left-hand side.
The Bird Recording —
Switches are the first Swiiched (1:8)
eight switches (FIG. 2) | тете: еж
in Switch Array #1. Each | necomomo4
switch has a recording | mew)
number to the left of it | ==>
that corresponds withthe |“...
bird descriptions listed
on the foil label inside the cover on the front the
unit, they are as follows:
FIG. 2
1 Blackbird 5 Raven
2 Crow 6 Bird Predator |
3 Grackle 7 Bird Predator ||
4 Cormorant 8 Bird Predator Ill
For best results, choose a combination of both
predator calls AND bird distress recordings to
create the most natural scenario.
S
The Mode Setting Switches are the last five
switches (FIG. 3) in Switch Array #2. These
set the various modes of operation: such as the
amount of time between Pr bird distress
calls, when the unit will recono || кан
operate (day only, night 3,
only, or 24-hours), and
whether the unit will
operate in the random > pode sena
mode or normal mode.
Switch Mode or Function
1 Sets the Time-Off Period
2 Sets the Time-Off Period
3 Sets the Time the unit plays
4 Sets the Time the unit plays
5 Turns Random Mode On or Off
DELAY SWITCHES
The two "Delay" or Time- renee |
Off Switches are located mor (ED)
just below the Recording PAN | |
Switches (1-8) in the switch |
array (FIG. 4). The unit will
delay a number of seconds or minutes between
recorded sounds when the unit is set to one
of the various Time-Off Modes. The TEST
setting is appropriate for testing, but is NOT
recommended for long-term success. Please
note that the unit will play all of the selected
recordings (either sequentially or non-sequentially,
depending on the Random Mode), then it will go
into a delay. The time the unit stays off depends
on the Time-Off and the Random Mode Settings.
If the unit is operating in Random Mode, the unit
will delay anywhere from the minimum value to
the maximum value for that Time-Off setting. If
the unit is not in Random Mode, it will delay only
the minimum value.
To set the Time-Off period (or delay interval), use
the following settings on switches 1 and 2 in the
Mode Function Settings.
Switch 1 Switch 2 Time Off Period
ON OFF Test (17-50 sec.)
OFF ON Medium (1-4 min.)
ON ON Long (5-10 min.)
OFF OFF X Long (10-30 min.)
The two Time of Operation switches are located
just under the Time-Off "E FTE
Switches in the switch ore | | =m:
array (FIG. 5). The unit permanent (ES)
will operate day only, night |
only, or continuously (24-
hours). However, the photocell that senses the
sunlight is susceptible to bright lights. Take care
not to have bright lights shining toward the front
of the unit since this can prevent the unit from
operating properly. To set the time period for the
unit to operate set switches 3 and 4 in the Mode
Function settings to the following:
Switch 3 Switch 4 Mode
ON OFF Day Only
OFF ON 24-Hour
ON ON Night Only
OFF OFF Night Only
BANDOM OPERATION SWITCH
The Random Operation Switch is the bottom
switch in the switch array (FIG. 8). 19 unit will
randomly play the selected
recordings in non-sequential
order when operating in
Random Mode. When the
unit is not operating in the Random Mode, the unit
will play the selected recordings in a sequential
order. The Random Mode is recommended to
keep birds from adapting to a preset pattern of
sounds. To operate the unit in Random Mode, set
switch 5 as follows:
Switch 5 Mode
ON Random mode ON
OFF Random mode OFF
PROGRAMMING EXAMPLE
Bird Recording Switches: Results:
1, 3, 5 and 6 to “ON” position Plays Birds 1, 3,5 & 6
Mode Switches:
1 = “OFF” position
2 = “ON” position (Medium), every 1 to 4 minutes
3 = "ON" position
4 = “OFF” position Operates during daylight hours only
5="0ON" position In random, non-sequential order
VOLUME CONTROL
The unit has a volume control dial on the front
panel of the unit. Turning the dial toward LOW will
reduce sound output and rotating the dial toward