FOXEER 700TVL Instruction manual

3. Long press top button, you can setup user name, OSD info enable or
disable separately, besides, you can also setup font, S1/S2/S3, default is
S2, and you can reset to default setup, press EXIT to save.
4. Long press bottom button, voltage flicker, you can move voltage
position, after setup, press center button, you can adjust voltage if the
OSD voltage is not same as real power, after setup, press center button,
voltage stop flicker
1. Lens
This function is used to adjust the
brightness of the screen.
1. MANUAL: For use with a manual iris
lens.
600TVL/700TVL CCD Mini FPV Camera
Instruction Manual
2. DC: For use with a DC drive auto iris
lens.
3. VIDEO: For use with a video drive
auto iris lens.
WARNING: Read the ENTIRE instruction manual to become familiar
with the features of the product before operating. Failure to operate
the product correctly can result in damage to the product, personal
property and cause serious injury.
Age Recommendation:
Not for children under 14 years. This is
not a toy.
SUPPORT: Visit www.foxeer.com/support to get more information.
1.SHUTTER- Condition and speed control
Auto: Shutter speed is controlled
automatically according to the
brightness of the scene.
FLK: Select when flickering occurs
due to imbalance between
illumination and frequency. PAL
Mode: 1/100, NTSC Mode: 1/120.
2. BRIGHTNESS- Adjust brightness from
0-255
3. AGC- Depending on lightness of
surroundings select HIGH, MID, LOW
or OFF.
CAMERA-OSD SWITCH CONNECTION
4 Pin To Video Transmitter
2 Pin To OSD
Switch board
Voltage Senser
connect with battery directly
VSEN
GND
OSD
AUD
VID
GND
VCC
MINI FPV CAM
Camera Back
DC 5-35V in (Red)
Ground Wire(Black)
Video out(Yellow)
Audio out(Green)
OSD (White)
Ground Wire(Black)
Voltage Senser(Blue)
OSD SwitchFront
CAMERA-VIDEO TRANSMITTER CONNECTION
To connect the camera directly to the video transmitter, plug the 4 pin wiring
harness from the video transmitter into the camera leaving the OSD pin open.
OSD MENU
MENU: Push MENU (center button) to go to the main menu.
Use when there is a strong backlight
behind the object, clear images of the
background as well as the object can
still be obtained.
2. HLC
Adjust level from 0~255. There are
two options: night only, all day.
SETUP
LENS
EXPOSURE
BACKLIGHT
WHITE BAL
DAY&NIGHT
SPECIAL
IMAGE ADJ
DPC
LANGUAGE
RESET
EXIT
MANUAL
OFF
ATW1
AUTO
ENGLIST
EXPOSURE
SHUTTER
BRIGHTENESS
AGC
DWDR
RETURN
AUTO
050
---OFF
RET
1. ATW (Auto Tracking White Balance)Ideal for color temps from
1800ºK~10500ºK ( fluorescent light,
outdoor, sodium vapor lamp, etc.)
Red 0~255
Left/Right: Modify the menu parameters.
Blue 0~255
FPV OSD Setup
SETUP
LENS
EXPOSURE
BACKLIGHT
WHITE BAL
DAY&NIGHT
SPECIAL
IMAGE ADJ
DPC
LANGUAGE
RESET
EXIT
MANUAL
OFF
ATW1
AUTO
ENGLIST
4 WHITE BAL (WHITE BALANCE)
2. MANUAL- Select ATW and change to
Manual mode.
UP/DOWN: Move up and down through the menu.
2. Long press right button, time flicker,
you can move time position, after setup,
press center button to save, time stop
flicker
ENGLIST
4. DWDR- Depending on lightness of
surroundings turn OFF or ON (Adjust
brightness from 0-63).
1. BLC ( Backlight Compensation)
CAUTION: If you are using ESC’s with active braking, we recommend
powering the camera system through a BEC or voltage regulator.
1. Long press left button, user name info
will flicker, you can move user name
position now, after setup, press center
button to save, user name stop flicker
OFF
ATW1
AUTO
3. BACKLIGHT
7 Pin Harness
VCC
GND
VID
AUD
OSD
GND
VSEN
MANUAL
2. EXPOSURE
FIXED: Select shutter speeds from
1/50 to 1/100000.
NOTICE: This product is only intended for use with unmanned, hobbygrade, remote-controlled vehicles and aircraft. FOXEER disclaims all
liability outside of the intended purpose and will not provide
warranty service related thereto.
SETUP
LENS
EXPOSURE
BACKLIGHT
WHITE BAL
DAY&NIGHT
SPECIAL
IMAGE ADJ
DPC
LANGUAGE
RESET
EXIT
SETUP
LENS
EXPOSURE
BACKLIGHT
WHITE BAL
DAY&NIGHT
SPECIAL
IMAGE ADJ
DPC
LANGUAGE
RESET
EXIT
MANUAL
OFF
ATW1
AUTO
ENGLIST
Select RETURN when finished.
5.Day & Night
FOXEER
0123456789
ABCDEFGHIJKLMOP
QRSTUVWXYZ():.<>/FONT
:
NAME :
TIME
:
POWER :
DEFAULT :
EXIT
:
S2
ON
ON
ON
Day & Night switch is specially designed for different occasions. There are
four kinds of modes.
• Auto mode
• Color mode
• B/W mode
• External switch
8. DPC
1. Color to B/W
When in External Control this can’t be adjusted. This is color to B/W
accumulated light intensity, when it reach “alternating light” state,
camera could be damaged by frequent switch. It might cause to not
correct judgment of image and reduction of span life of the device.
Set the black point and white point as
auto-completion-point numbers.
2. B/W TO COLOR
When in External Control this can’t be
adjusted. This is B/W to color
accumulated light intensity, when it
reach “alternating light” state, camera
could be damaged by frequent
switch. It might cause to not correct
judgment of image and reduction of
span life of the device.
SETUP
LENS
EXPOSURE
BACKLIGHT
WHITE BAL
DAY&NIGHT
SPECIAL
IMAGE ADJ
DPC
LANGUAGE
RESET
EXIT
MANUAL
OFF
ATW1
AUTO
ENGLISH/CHINESE
ENGLIST
Delay before color state begins to alternate.
6. SPECIAL
2. MOITON - Motion detection
Choose the area and press ENTER to
confirm. The color of the chosen
area will change. Repeat to choose
other areas. After 1 second of
inactivity it will move to the next
menu item.
SETUP
LENS
EXPOSURE
BACKLIGHT
WHITE BAL
DAY&NIGHT
SPECIAL
IMAGE ADJ
DPC
LANGUAGE
RESET
EXIT
MANUAL
OFF
ATW1
AUTO
1. FACTORY
Return to camera’s initial setting.
ENGLIST
3. PRIVACY - Conceal the areas(OFF/ON)
(1) AREA SEL: Set 4 privacy areas.
(2) AREA STATE: Select AREA STATE ON to conceal AREA selected. OFF
to disable Privacy.
Save all settings and exit to Main Menu.
(4) COLOR: Select the color of each privacy area by slider.
(5) RETRUN: Return to previous menu.
4. PARK LINE - OFF/ON
(1) CAM ID: Set camera ID from
0~255
(2) BAUD RATE: Set camera
communication speed from 2400
to 38400
VOLTAGE DISPLAY
COMM ADJ
CAMID
BAUDRATE
PROTOCOL
DISPLAYID
IDPOS
RETURN
001
4800
PELCO-D
OFF
RET
(3) PROTOCOL
(4) DISPLAY ID: OFF/ON
(5) ID POS
6. VERSION
7. IMAGE ADJ
(1) Lens sharp: OFF/ON, adjust from
0~255
(2) 2DNR: OFF/ON
(3) Mirror: OFF/ON
(4) FONT COLOR: Adjusted from 0 to 51
(5) CONTRASR: Adjusted from 0 to 255
(6) SHARPNESS: Adjusted from 0 to 255
(7) DISPLAY CRT/LCD
SETUP
LENS
EXPOSURE
BACKLIGHT
WHITE BAL
DAY&NIGHT
SPECIAL
IMAGE ADJ
DPC
LANGUAGE
RESET
EXIT
(8) NEG IMAGE: OFF/ON
TM and © 2016 FOXEER ALL rights reserved.
www.foxeer.com
MANUAL
OFF
ATW1
AUTO
ENGLIST
ENGLIST
SETUP
LENS
EXPOSURE
BACKLIGHT
WHITE BAL
DAY&NIGHT
SPECIAL
IMAGE ADJ
DPC
LANGUAGE
RESET
EXIT
MANUAL
OFF
ATW1
AUTO
ENGLIST
SETUP
LENS
EXPOSURE
BACKLIGHT
WHITE BAL
DAY&NIGHT
SPECIAL
IMAGE ADJ
DPC
LANGUAGE
RESET
EXIT
MANUAL
OFF
ATW1
AUTO
ENGLIST
11. EXIT
(3) LEFT/RIGHT/TOP/BOTTOM: Set the dimension of each privacy area
by slider.
5. COMM ADJ
OFF
ATW1
AUTO
10. RESET
2. RETURN
Conceal the areas where you don’t wish to appear on the screen.
MANUAL
9. LANGUAGE
3. DELAY TIME
1. CAM Title - Set the title background
SETUP
LENS
EXPOSURE
BACKLIGHT
WHITE BAL
DAY&NIGHT
SPECIAL
IMAGE ADJ
DPC
LANGUAGE
RESET
EXIT
CAM IN
GND
VIDEO
AUDIO
OSD
GND
VSEN connect with battery directly
SETUP
LENS
EXPOSURE
BACKLIGHT
WHITE BAL
DAY&NIGHT
SPECIAL
IMAGE ADJ
DPC
LANGUAGE
RESET
EXIT
MANUAL
OFF
ATW1
AUTO
ENGLIST