The JA-80N outdoor RFID card reader

The JA-80N outdoor RFID card reader
The JA-80N is a component of Jablotron’s Oasis
80 alarm system. It is designed to control access
(door lock) or to control a security system and
connects to the Oasis control panel via a WJ-80
interface.
Alternatively it can be connected to an AS-80 unit
as a part of a stand-alone access system.
Technical specifications
Power supply
10 to 16V DC
Stand-by consumption
typically 60mA
Enclosure protection (EN 60529)
IP65
Mechanical endurance (EN 50102)
IK08
Environmental (EN 50131-1)
class IV – outdoor general
Operational temperature range
-25 to +60°C
RFID card
Jablotron PC-01 or PC-02 (EM UNIQUE 125 kHz)
Dimensions
46 x 150.5 x 22.5mm
Length of the connection cable
1m
Complies with grade 2 (EN 50131-1, TS 50131-3)
Can be operated according to ERC REC 70-03
The keypad sends data in Wiegand 26b format.
Installation
Installation shall only be undertaken by technicians
holding a certificate issued by an authorized
distributor. It is usually placed near an entrance door
(equipped with an electronic lock). The reader can be
used outdoors (conforms to IP-65).
1. Open the rear cover by unscrewing the screw
2. Prepare a hole in the wall for the reader cable to pass
through, where the reader will be located.
3. Attach the rear cover to the desired location (the
tamper spring must be properly pressed)
4. Pull the reader cable through the wall hole and to the
interface unit’s box (WJ-80, AS-80)
5. Attach the reader to the rear cover and secure it using
the screw
6. Connecting and setting up the reader is described in
the WJ-80 or AS-80 manuals.
FCC ID VL6JA80N
Jablotron Ltd. hereby declares that the JA-80N is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC and complies
with part 15 of the FCC rules. Operation is subject to the following two conditions: 1.
This device may not cause harmful interference, and 2. This device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Changes or modifications no expressly approved by Jablotron could void the
user´s authority to operate the equipment. The original of the conformity assessment can
be found at www.jablotron.com, Technical Support section.
Note: Although this product does not contain any harmful materials
we suggest you return the product to the dealer or directly to the
producer after use.
cca 1 m
Cabling
wire
red
green
brown
white
grey
yellow
blue
pink
signal
+12V (power supply, 60mA)
D0 (Wiegand 26b data output)
D1 (Wiegand 26b data output)
TMP (normally closed tamper contact)
TMP (normally closed tamper contact)
BZR (input controlling reader’s sound – connecting to GND
generates a beep on the reader)
GND (common ground)
not connected
151,5
If the JA-80N reader is connected to an Oasis control panel and it does
not work as described in the manual, then it is not set to the correct
(factory default) operational mode. In such a case:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Switch the Oasis control panel to service mode
Disconnect the power from the control panel (mains and battery)
Get an RFID card ready (PC-01 or PC-02)
Disconnect the yellow and brown wires from the WJ-80 interface
terminals and connect the wires together
Power-up the control panel (reader starts beeping)
Disconnect the yellow and brown wires from each other (beeping will
terminate)
Use the RFID card 4 times (put it close to the reader and after a short beep
take it away) – then wait a moment until a few beeps sound (by this
procedure you enter “4” without pressing a key, as there are no keys to
press)
Now use the RFID card 3 times (put it close to the reader and after a short
beep take it away) – then wait a moment until a few beeps sound (by this
procedure you enter “3” without pressing a key, as there are no keys to
press)
Disconnect the power from the control panel, connect the yellow and brown
wires back up, power-up the control panel and check the proper functioning
of the JA-80H keypad
45
87,5
TAMPER
Configuring the reader for operation with the WJ-80
22,5
Note: The red LED is lit in normal operating mode. Using a card is confirmed
by a flash from the orange LED.
How to set up the JA-80N reader for the AS-80 access system is described in
the AS-80 manual.
The JA-80N outdoor RFID card reader
1
MKM51201