DVD-1080P9
DVD-1080PR
DVD Player
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register your
product at
www.samsung.com/global/register
AK68-01750K(01)
Precautions
1. Setting up
- Refer to the identification label located on the
rear of your player for its proper operating
voltage.
- Install your player in a cabinet with adequate
ventilation holes. (7~10cm) Do not block
ventilation holes on any of the components
for air circulation.
- Do not push the disc tray in by hand.
- Do not stack components.
- Be sure to turn all components off before
moving the player.
- Before connecting other components to this
player, be sure to turn them off.
- Be sure to remove the disc and turn off the
player after use, especially if you are not
going to use it for a long time.
- The mains plug is used as a disconnect
device and shall stay readily operable at
any time.
2. For your safety
- This product utilizes a laser. Use of controls
or adjustments or performance of procedures
other than those specified herein may result
in hazardous radiation exposure.
- Do not open covers and do not repair yourself.
Refer servicing to qualified personal.
3. Caution
- Your player is not intended for industrial use
but for domestic purposes. Use of this
product is for personal use only.
- Apparatus shall not be exposed to dripping
or splashing and no objects filled with liquids,
such as vases, shall be placed on the
apparatus.
- Exterior influences such as lightning and
static electricity can affect normal operation
of this player. If this occurs, turn the player
off and on again with the POWER button,
or disconnect and then reconnect the AC
power cord to the AC power outlet. The
player will operate normally.
- When condensation forms inside the player
due to sharp changes in temperature, the
2_ Precautions
player may not operate correctly. If this
occurs, leave the player at room temperature
until the inside of the player becomes dry
and operational.
4. Disc
- Do not clean disc using record-cleaning
sprays, benzene, thinner, or other volatile
solvents that may cause damage to the disc
surface.
- Do not touch the disc’s signal surface. Hold
by the edges or by one edge and the hole
in the center.
- Wipe the dirt away gently; never wipe a
cloth back and forth over the disc.
5. Environmental info
- The battery used in this product contains
chemicals that are harmful to the environment.
- So, dispose of batteries in the proper man
ner, according to federal, state, and local
regulations.
The product unit accompanying this user manual
is licenced under certain intellectual property rights
of certain third parties. This licence is limited to
private non-commercial use by end-user consumers
for licenced contents. No rights are granted for
commercial use. The licence does not cover any
product unit other than this product unit and the
licence does not extend to any unlicenced product
unit or process conforming to ISO/OUR 11172-3 or
ISO/OUR 13818-3 used or sold in combination with
this product unit. The licence only covers the use of
this product unit to encode and/or decode audio files
conforming to the ISO/OUR 11172-3 or ISO/OUR
13818-3. No rights are granted under this licence for
product features or functions that do not conform to
the ISO/OUR 11172-3 or ISO/OUR 13818-3.
CAUTION: USE OF ANY CONTROLS,
ADJUSTMENTS, OR PROCEDURES OTHER
THAN SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
Before you start Table of contents
Accessories
Check for the supplied accessories below.
Remote Control
User’s Manual
Batteries for Remote
Control (AAA Size)
Video/Audio
Cable
The accessories which do not suplied.
• Scart Cable
• HDMI-HDMI Cable
• Component Cable
• HDMI-DVI Cable
• Coaxial Cable
Install Batteries in the Remote
control
1. Open the battery cover on the back of the remote
control.
2. Insert two AAA batteries. Make sure that the
polarities (+ and -) are aligned correctly.
3. Replace the battery cover.
If remote control doesn’t operate
properly:
- Check the polarity + - of the batteries (Dry-Cell)
- Check if the batteries are drained.
- Check if remote control sensor is blocked by
obstacles.
- Check if there is any fluorescent lighting nearby.
- The rechargeable battery incorporated in this
product is not user replaceable.
- For information on its replacement, please
contact your service provider.
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Setup
General Features . . . . . . . . . . . . . . . . . . . . . . . . . .4
Disc Type and Characteristics . . . . . . . . . . . . . . . .5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Tour of the Remote Control . . . . . . . . . . . . . . . . . . .8
Connections
Choosing a Connection . . . . . . . . . . . . . . . . . . . . .9
Basic Functions
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Using the Search and Skip Functions . . . . . . . . .16
Using the Display Function . . . . . . . . . . . . . . . . .17
Using the Disc and Title Menu . . . . . . . . . . . . . . .17
Using the Function Menu . . . . . . . . . . . . . . . . . . .18
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Advanced Functions
Adjusting the Aspect Ratio (EZ View) . . . . . . . . . .19
Selecting the Audio Language . . . . . . . . . . . . . . .19
Selecting the Subtitle Language . . . . . . . . . . . . . .20
Changing the Camera Angle . . . . . . . . . . . . . . . . .20
Using the Bookmark Function . . . . . . . . . . . . . . . .20
Using the Zoom Function . . . . . . . . . . . . . . . . . . .21
Clips Menu for MP3/WMA/JPEG/MPEG4/
CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . .22
MP3/WMA/CD Audio Playback . . . . . . . . . . . . . . .22
MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . .23
Playing Media Files using the USB HOST
feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
CD Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Picture CD Playback . . . . . . . . . . . . . . . . . . . . . . .25
Picture CD Playback for HD-JPEG . . . . . . . . . . . .26
Changing Setup Menu
Using the Setup Menu. . . . . . . . . . . . . . . . . . . . . .27
Setting Up the Language Features . . . . . . . . . . . .27
Setting Up the Audio Options . . . . . . . . . . . . . . . .28
Setting Up the Display Options . . . . . . . . . . . . . . .29
Setting Up the Parental Control . . . . . . . . . . . . . .32
Setting Up the Anynet+(HDMI-CEC) . . . . . . . . . . .33
Reference
Firmware Upgrade. . . . . . . . . . . . . . . . . . . . . . . . .34
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
English _3
Setup
General Features
Excellent Sound
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound reproduction.
Screen
Both regular and widescreen(16:9) pictures can be
viewed.
Slow Motion
An important scene can be viewed in slow motion.
1080p Playback
This player upconverts regular DVDs for playback
on 1080p TVs.
Parental Control (DVD)
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
Progressive Scan
Progressive scanning creates an improved picture
with double the scan lines of a conventional interlaced picture.
EZ VIEW (DVD)
Easy View enables picture adjustment to match
your TV's screen size (16:9 or 4:3).
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
MP3/WMA
This unit can play discs created from MP3/WMA
files.
MPEG4
This unit can play MPEG4 formats within an avi file.
HDMI (High Definition Multimedia
Interface)
HDMI reduces picture noise by allowing a pure
digital video/audio signal path from the player to
your TV.
CD Ripping
This feature lets you to copy audio files from disc to
USB device into MP3 format. (Only Audio CD (CD DA))
4_ Setup
Note
- Discs which cannot be played with this player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
• CDI
• CVD
• CDGs play audio only, not graphics.
- Ability to play back may depend on recording
conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW (V mode)
- The unit may not play certain CD-R, CD-RW
and DVD-R due to the disc type or recording
conditions.
COPY PROTECTION
Many DVD discs are encoded with copy protection.
Because of this, you should only connect your DVD
player directly to your TV, not to a VCR. Connecting
to a VCR results in a distorted picture from copyprotected DVD discs.
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be auzthorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
PROGRESSIVE SCAN OUTPUTS
(576p,720p,1080p)
“CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE
FULLY COMPATIBLE WITH THIS PRODUCT
AND MAY CAUSE ARTIFACTS TO BE
DISPLAYED IN THE PICTURE, IN CASE OF
576, 720, 1080 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE
USER SWITCH THE CONNECTION TO THE
‘STANDARD DEFINITION’ OUTPUT. IF THERE
ARE QUESTIONS REGARDING YOUR TV SET
COMPATIBILITY WITH THIS MODEL 576p,
720p, 1080p DVD PLAYER, PLEASE CONTACT
SAMSUNG'S CUSTOMER SERVICE CENTER.”
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos:
Disc Types (Logos)
Recording Types
Audio
+
Video
AUDIO-CD
Max. Playing Time
12 Cm
Single-sided 240 min.
Double-sided 480 min.
- DVD contains excellent sound and
video due to Dolby Digital and MPEG2 system.
8 Cm
Single-sided 80 min.
Double-sided 160 min.
- Various screen and audio functions
can be easily selected through the onscreen menu.
12 Cm
74 min.
8 Cm
20 min.
Audio
Characteristics
- CD is recorded as a Digital Signal
with better audio quality, less distortion and less deterioration of audio
quality over time.
Disc Markings
Region Number
~
PAL
Play Region Number
PAL broadcast system in U.K, France,
Germany, etc.
Dolby Digital disc
STEREO
DIGITAL
SOUND
Stereo disc
Digital Audio disc
Both the DVD player and the discs are coded
by region. These regional codes must match
in order for the disc to play. If the codes do not
match, the disc will not play.
The Region Number for this player is
described on the rear panel of the player.
DTS disc
MP3 disc
You must only insert one DVD disc at a time
or you may cause damage to the DVD player.
DivX Certification
DivX, DivX Certified,
and associated logos are trademarks of
DivXNetworks, Inc and are used under
license
English _5
● SETUP
DVD
Disc Size
Setup
Description
Front Panel Controls
8 7
9
1.
DISC TRAY
Place the disc here.
6.
STOP ( )
Stops disc play.
2.
OPEN/CLOSE ( )
Press to open and close the disc tray.
7.
SKIP ( ) / SEARCH
Use to reverse skip a scene or music.
3.
DISPLAY
Operation indicators are displayed here.
8.
4.
PLAY/PAUSE ( )
Begin or pause disc play.
USB HOST
Connect digital still camera, MP3 player, memory stick,
Card reader other removable storage devices.
9.
5.
SKIP ( ) / SEARCH
Use to forward skip a scene or music.
POWER ON/OFF (
)
Turn on/off and the player is turned on/off.
Front Panel Display
DVD
CD
USB
RW
HDMI
1080iP720P
7
1.
In Disc Indicator : DVD Video, Audio
6.
CD, CD-R/RW, DVD-R/RW/RAM,
DVD+R/RW
2.
DVD VIEW indicator
3.
CD indicator
4.
USB indicator
5.
Disc Media indicator : DVD-R, DVDRW, DVD+R, DVD+RW
6_ Setup
7.
HDMI indicator :
HDMI 480P ➔ “HDMI”,
HDMI 720P ➔ “HDMI + 720P”,
HDMI 1080i ➔ “HDMI + 1080i”,
HDMI 1080P ➔ “HDMI + 1080P”
Displays the Total playing time and
various messages concerning
operations such as PLAY, STOP,
LOAD ...
noDISC: No disc loaded.
OPEN: The disc tray is open.
LOAD: Player is loading disc information.
Rear Panel
● SETUP
- If P-SCAN Video Output is selected in Setup Menu,
progressive scan mode will work.
- If I-SCAN Video Output is selected in Setup Menu,
interlaced scan mode will work.
1.
SCART JACK
- Connect to a TV scart input jack
2.
AUDIO OUT JACKS
- Connect to the Audio input jacks of your television or
audio/video receiver.
5.
DIGITAL AUDIO JACKS
- Use either an coaxial digital cable to connect to a
compatible Dolby Digital receiver.
- Use either an coaxial digital cable to connect to an
A/V Amplifier that contains a Dolby Digital, MPEG2 or
DTS decoder.
HDMI OUT JACK
- Use the HDMI cable to connect this jack to the HDMI
jack on your television for the best quality picture.
- If an HDMI cable is connected to an HDMI-compatible TV, HDMI will be output automatically within 10
seconds.
6.
VIDEO OUT JACK
- Use a video cable to connect to the Video input jack
on your television.
3.
4.
COMPONENT VIDEO OUT JACKS
- Use these jacks if you have a TV with Component
Video in jacks. These jacks provide PR, PB and Y
video.
Note
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN).
If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in
the TV’s menu system.
- The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conversion adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input.
- There may be no image output if the DVD player is connected to a TV or display that is not compatible
with the above format.
- Refer to the TV's instruction manual for detailed information regarding the HDMI terminal.
- See pages 29 ~ 31 to get more information on how to use the setup menu.
English _7
Setup
Tour of the Remote Control
8.
9.
1
17
18
2
19
20
21
22
23
3
4
5
6
7
8
9
10
24
11
27
10.
11.
12.
13.
14.
25
15.
26
16.
12
17.
18.
13
28
14
29
15
30
16
31
19.
20.
21.
22.
23.
24.
1.
2.
3.
4.
5.
6.
7.
DVD POWER Button
Turns the power on or off.
NUMBER Buttons
SUBTITLE (Number 4) Button
TITLE MENU (Number 7) Button
Brings up the Title Menu.
ZOOM/-/-- Button
Enlarges the DVD Picture. Use this button to select the
channel TV program by inserted the channel (TV mode).
TV VOL (+, -) Buttons
Control volume.
SEARCH Buttons (k/K)
Allow you to search forward/backward through a disc.
8_ Setup
25.
26.
27.
28.
29.
30.
31.
VIDEO SEL. Button
Selects video output formats.
SKIP Buttons (|k/K|)
Use to skip the title, chapter or track.
STOP Button (■)
MENU Button
Brings up the DVD player’s menu.
ENTER/π/†,√/® Buttons
This button functions as a toggle switch.
INFO Button
Displays the current disc mode.
DISC MENU Button
Brings up the Disc menu.
OPEN/CLOSE (
) Button
To open and close the disc tray.
HDMI SEL. Button
HDMI Output resolution setup.
DVD Button
This button when you use a DVD player.
TV Button
This button when you use a Samsung TV.
EZ VIEW (Number 6) Button
The aspect ratio of a picture can easily be adjusted
according to the screen size of your TV (16:9 or 4:3).
AUDIO (Number 5) Button
Use this button to access various audio functions on a disc.
BOOKMARK (Number 9) Button
REPEAT A-B (Number 8) Button
Allows you to repeat play A-B on a disc.
STEP/TV SOURCE Button
Advances play one frame at a time. Use this button to
select an available TV source (mode TV)
TV CH (P, Q) Buttons
Channel selection.
PAUSE Button (∏∏)
Pause disc play.
PLAY Button ()
Begin disc play.
RETURN Button
Returns to a previous menu.
EXIT Button
Exit the on-screen menu.
CANCEL Button
Use to remove menus or status displays from the screen.
USB Button
REPEAT Button
Allows you to repeat play a title, chapter, track, or disc.
Connections
Choosing a Connection
The following shows examples of connections commonly used to connect the DVD player with a TV and
other components.
- Refer to the user’s manual of the additional components you are connecting for more information on those
particular components.
Connecting to a TV (VIDEO CVBS)
1
Using video/audio cables, connect the VIDEO (yellow)/
AUDIO (red and white) OUT terminals on the rear of the
DVD player to the VIDEO (yellow)/AUDIO (red and white)
IN terminals of TV.
2
WHITE
Turn on the DVD player and TV.
RED
YELLOW
Audio
Cable
RED
Video Cable
WHITE
YELLOW
3
Press the input selector on your TV remote control until
the Video signal from the DVD player appears on the TV
screen.
Note
- Noise may be generated if the audio cable is too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 14 to 15)
- The number and position of terminals can vary depending on your TV set. Please refer to the user's
manual of the TV.
- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the
DVD player.
- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video
Output mode changes in the following sequence: (I-SCAN ➝ P-SCAN ➝ SCART-RGB ➝ SCART-CVBS)
English _9
● CONNECTIONS
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
Connections
Connection to a TV (Interlace)
- Connecting to your TV using Component video cables.
- You will enjoy high quality and accurate colour reproduction images. Component video separates the
picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images.
(Audio signals are delivered through the audio output.)
1
Using component video cables, connect the
COMPONENT VIDEO OUT terminal on the rear of the
DVD player to the COMPONENT IN terminal of TV.
2
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of TV. Turn on the
DVD player and TV.
WHITE
BLUE
GREEN
RED
RED
Audio
Cable
Component Cable
RED
WHITE
RED BLUE
GREEN
3
Press the input selector on your TV remote control until the
Component signal from the DVD player appears on the TV
screen.
Do not use the connection Scart and
Component Video (Y, Pb, Pr) simultaneously.
4
Set the Video Output to I-SCAN in the Display Setup
menu. (See pages 29 to 31)
You can use the VIDEO SEL. button to change the Video
Output mode. (See page 9)
Note
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 14 to 15)
- The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “PR, PB, Y”
depending on the manufacturer. The number and position of terminals can vary depending on the TV set.
Please refer to the user's manual of the TV.
- There is no Component video displayed when "Scart RGB" selected by pressing video select button on
remote control.
10_ Connections
Connection to a TV (Progressive)
1
Using component video cables, connect the
COMPONENT VIDEO OUT terminal on the rear of the
DVD player to the COMPONENT IN terminal of TV.
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of TV. Turn on the
DVD player and TV.
WHITE
BLUE
GREEN
RED
RED
Audio
Cable
Component Cable
RED
WHITE
RED BLUE
GREEN
3
Press the input selector on your TV remote control until the
Component signal from the DVD player appears on the TV
screen.
Do not use the connection Scart and
Component Video (Y, Pb, Pr) simultaneously.
4
Set the Video Output to P-SCAN in the Display Setup
menu. (See pages 29 to 31)
You can use the VIDEO SEL. button to change the Video
Output mode. (See page 9)
To see the progressive video output,
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive
Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s
menu system.
- Depending on your TV, the connection method may differ from the illustration above.
Note
- What is "Progressive Scan"?
Progressive scan has twice as many scanning lines as the interlace output method. Progressive
scanning method can provide better and clearer picture quality.
- There is no Component video displayed when "Scart RGB" selected by pressing video select button on
remote control.
English _11
● CONNECTIONS
2
Connections
Connecting to a TV (SCART)
1
Using scart cable, connect to SCART terminal on the rear of
the DVD player to the SCART IN terminals of TV.
2
Turn on the DVD player and TV.
Scart Cable
Do not use the connection Scart and
3
Press the input selector on your TV remote control until
the Video signal from the DVD player appears on the TV
screen.
Component Video (Y, Pb, Pr) simultaneously.
Note
- Noise may be generated if the audio cable is too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 14 to 15)
- The number and position of terminals can vary depending on your TV set. Please refer to the user's
manual of the TV.
- Please do not connect Scart and Component Video (Y, Pb, Pr) output simultaneously, as they may interfere and degrade both video output quality.
12_ Connections
Connecting to a TV with DVI Jack
1
Using the HDMI-DVI cable , connect the HDMI OUT terminal on the rear of the DVD player to the DVI IN terminal
of your TV.
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of your TV. Turn on
the DVD player and TV.
● CONNECTIONS
2
WHITE
RED
RED
Audio Cable
WHITE
HDMI-DVI cable
3
Press the input selector on your TV remote control until
the DVI signal from the DVD player appears on your TV
screen.
Connecting to a TV with HDMI Jack
1
Using the HDMI-HDMI cable connect the HDMI OUT terminal on the rear of the DVD player to the HDMI IN terminal
of your TV.
2
Press the input selector on your TV remote control until
the HDMI signal from the DVD player appears on your TV
screen.
HDMI cable
HDMI VIDEO Specifications
When you press the HDMI SEL. button, 480p, 576p, 720p, 1080p, 1080i are selected in order.
The first press of the HDMI SEL. button brings up the current resolution.
The second press allows you to change the HDMI output resolution.
- Certain HDMI output resolutions may not work, depending on your TV.
- Please refer to the user's manual of your TV.
- If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI within 10
seconds.
- If you set the HDMI output resolution 720p,1080p or 1080i, HDMI output provides better picture
quality.
- If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this DVD player
using your TV remote control. This is only available with Samsung TVs that support Anynet+(HDMI-CEC).
(See page 33).
- If your TV has an
logo, then it will
Supports the Anynet+ Function.
English _13
Connections
• HDMI (High Definition Multimedia Interface)
HDMI is an interface to enable the digital transmission
of video and audio data with just a single connector.
Using HDMI, the DVD player transmits a digital video
and audio signal and displays a vivid picture on a TV
having an HDMI input jack.
• HDMI connection description
HDMI connector - Both uncompressed video data and
digital audio data (LPCM or Bit Stream data).
- Though the player uses a HDMI cable, the player
outputs only a pure digital signal to the TV.
- If TV does not support HDCP (High-bandwidth
Digital content protection), snow noise appears on
the screen.
• Why does Samsung use HDMI?
Analog TVs require an analog video/audio signal.
However, when playing a DVD, the data transmitted
to a TV is digital. Therefore either a digital-to-analog
converter (in the DVD player) or an analog-to-digital
converter (in the TV) is required. During this conversion, the picture quality is degraded due to noise and
signal loss. DVI technology is superior because it
requires no D/A conversion and is a pure digital signal from the player to your TV.
• What is the HDCP?
HDCP (High-bandwidth Digital Content Protection)
is a system for protecting DVD content outputted via
DVI from being copied. It provides a secure digital link
between a video source (PC, DVD. etc) and a display
device (TV, projector . etc). Content is encrypted at
the source device to prevent unauthorized
Connection to an Audio System (2 Channel Amplifier)
1
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO or
COMPONENT OUT terminals on the rear of the DVD
player to the VIDEO or COMPONENT IN terminal of your
TV as described on pages 9 to 14.
WHITE
RED
3
Audio Cable
RED
WHITE
Turn on the DVD player, TV, and Amplifier.
2-Channel stereo
ampilfier
4
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your hearing.
- Please set the audio in the menu screen according to the Amplifier. (See pages 28-29)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
14_ Connections
Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)
1
If using a coaxial cable, connect the DIGITAL AUDIO OUT
(COAXIAL) terminal on the rear of the DVD player to the
DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.
● CONNECTIONS
2
Using the video signal cable(s), connect the VIDEO,
COMPONENT or HDMI OUT terminals on the rear of the
DVD player to the VIDEO, COMPONENT or DVI IN terminals of your TV as described on pages 9 to 14.
Coaxial Cable
3
Dolby digital or
DTS amplifier
Turn on the DVD player, TV, and Amplifier.
4
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Refer to your Amplifier's user manual to set the Amplifier's
audio input.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your hearing.
- Please set the audio in the menu screen according to the Amplifier. (See pages 28 to 29)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
English _15
Basic functions
Playing a Disc
Before Play
- Turn on your TV and set it to the correct Video
Input by pressing TV/VIDEO button on the TV
remote control.
- If you connected an external Audio System, turn
on your Audio System and set it to the correct
Audio Input.
After plugging in the player, the first time you press the DVD
POWER button, this screen comes up: If you want to select
a language, press a NUMBER button. (This screen will only
appear when you plug in the player for the first time.)
If the language for the startup screen is not set, the settings may change whenever you turn the power on or off.
Therefore, make sure that you select the language you want
to use.
Once you select a menu language, you can change it by
button on the front panel of the unit for
pressing the
more than 5 seconds with no disc in the unit. Then the
SELECT MENU LANGUAGE window appears again where
you can reset your preferred language.
Press
1
for English
Touche
2
pour Français
Drücken Sie
3
für Deutsch
Pulsar
4
para Español
Premere
5
per Italiano
Druk op
6
voor Nederlands
7. Step Motion Play (Except CD)
Press the STEP button on the remote control during play.
- Each time the button is pressed, a new frame will
appear.
- No sound is heard during STEP mode.
- Press the PLAY () button to resume normal play.
- You can only perform step motion play in the
forward direction.
8. Slow Motion Play
Press the SEARCH (k/K) button to choose the play
speed between 1/2, 1/4 and 1/8 of normal during PAUSE
or STEP mode.
- No sound is heard during slow mode.
- Press the PLAY () button to resume normal play.
Note
- If the player is left in the stop mode for more
than one minute without any user interaction, a
screen saver will be activated. Press the PLAY
() button to resume normal play.
- If the player is left in the stop mode for more than
about 30 minutes, the power will automatically
shut off.(Automatic Power-Off Function)
- If the player is left for about 5 minutes in pause
mode, it will stop.
- This ( ) icon indicates an invalid button press.
Playback
1. Press the OPEN/CLOSE ( ) button and the tray opens.
2. Place a disc gently into the tray with the disc’s label
facing up.
3. Press the PLAY () button or OPEN/ CLOSE ( )
button to close the disc tray.
- When you stop disc play, the player remembers
where you stopped, so when you press PLAY ()
button again, it will pick up where you left off.
4. Stopping Play
Press the STOP (■) button during play.
5. Removing Disc
Press the OPEN/CLOSE (
) button.
6. Pausing Play
Press the PAUSE (∏∏) or STEP button on the remote
control during play.
- Screen stops, no sound.
To resume, press the PLAY () button once again.
16_ Basic functions
Using the Search and Skip
Functions
During play, you can search quickly through a chapter or
track, and use the skip function to jump to the next selection.
Searching through a Chapter or
Track
During play, press the SEARCH (k or K) button on the
remote control for more than 1 second.
DVD
2X, 4X, 64X, 128X
CD
2X, 4X, 8X
Note
- The speed marked in this function may be
different from the actual playback speed.
- No sound is hearing during search mode
(Except CD).
Skipping Tracks
Using the Disc Menu
1. During the playback of a DVD disc, press the MENU button
on the remote control.
2. Press the π/† buttons to select Disc Menu, then press the
® or ENTER button.
Press ENTER key
for Disc Menu
Using the Display Function
When Playing a DVD/MPEG4
1. During play, press the INFO button on the remote control.
- You can select Info in the function menu by pressing
the MENU button.
2. Press the π/† buttons to select the desired item.
3. Press the √/® buttons to make the desired setup and then
press the ENTER button.
- You may use the number buttons of the remote control
to directly access a title, chapter or to start the play
back from a desired time.
4. To make the screen disappear, press the INFO button again.
Note
Title
To access the desired title when there is
more than one in the disc. For example, if
there is more than one movie on a DVD,
each movie will be identified.
Chapter
Most DVD discs are recorded in chapters so
that you can quickly find a specific passage.
Time
Allows playback of the film from a desired
time. You must enter the starting time as a
reference.The time search function does not
operate on some disc.
Audio
Subtitle
Refers to the language of the film soundtrack.
In the example, the soundtrack is played in
English 5.1CH. A DVD disc can have up to
eight different soundtracks.
Enter
Return
Menu
Note
- The Disc Menu may not work. Depending on the
disc.
- You can also use the Disc Menu, using the
DISC MENU button on the remote control.
Using the Title Menu
1. During the playback of a DVD disc, press the MENU button
on the remote control.
2. Press the π/† buttons to select Title Menu, then press the
® or ENTER button.
Press ENTER key
for Title Menu
Enter
Return
Menu
Note
- The Title Menu may not work. Depending on the
disc.
- Title Menu will only be displayed if there are at
least two titles in the disc.
Refers to the subtitle languages available
in the disc. You will be able to choose the
subtitle languages or, if you prefer, turn them
off from the screen. A DVD disc can have up
to 32 different subtitles.
English _17
● BASIC FUNCTIONS
During play, press the SKIP (|k or K|) button.
- When playing a DVD, if you press the SKIP (K|) button,
it moves to the next chapter. If you press the SKIP (|k)
button, it moves to the beginning of the chapter. One
more press makes it move to the beginning of the previous
chapter.
- When playing a CD in Menu Off mode, if you press the
SKIP (K|) button, it moves to the next track. If you press
the SKIP (|k) button, it moves to the beginning of the
track. One more press makes it move to the beginning of
the previous track.
Using the Disc and Title
Menu
Basic functions
Using the Function Menu
Using the Function Menu (DVD)
1. Press the MENU button during playback.
2. Press the π/† buttons to select Function, then press the
® or ENTER button.
- Info (See pages 17)
- Zoom (See page 21)
- Bookmark (See pages 20 to 21)
- EZ View (See pages 19)
- Angle (See pages 20)
Using the A-B Repeat function
1. Press the REPEAT A-B button at the point where you
want repeat play to start (A).
2. Press the REPEAT A-B button at the point where you
want the repeat play to stop (B).
2. To return to normal play, press the REPEAT A-B button.
Repeat:A-
Repeat:A-B
Info
Zoom
Bookmark
EZ View
Angle
Enter
Repeat:Off
Return
Menu
3. Press the π/† buttons to select one of the six functions.
Then press the ® or ENTER button to access the function.
You can also directly select these functions using their
respective buttons on the remote control.
- INFO
- ZOOM
- EZ VIEW
- BOOKMARK
- REPEAT
Repeat Play
Repeat the current track, chapter, title, a chosen
section (A-B), or all of the disc.
When playing a DVD
1. Press the REPEAT button on the remote control.
Repeat screen appears.
- DVD repeats play by chapter or title.
- Chapter : repeats the chapter that is playing.
- Title : repeats the title that is playing.
- Repeat : Off
Chapter
Title
Repeat:Off
18_ Basic functions
Note
- A-B REPEAT allows you to set point (B) until at
least 5 seconds of play back time has elapsed
after point (A) has been set.
- The Repeat function may not work. Depending
on the disc.
Slow Play
This feature allows you slowly to repeat scenes containing sports, dancing, musical instruments being
played etc., so you can study them more closely.
When playing a DVD
1. During play, press the PAUSE (∏∏) button.
2. Press the SEARCH (k/K) button to choose the play
speed between 1/2, 1/4 and 1/8 of normal during PAUSE or
STEP mode.
Advanced functions
Adjusting the Aspect Ratio
(EZ View)
Press the EZ VIEW button.
- The screen size changes when the button is pressed
repeatedly.
- The screen zoom mode operates differently depending on the
screen setting in the Display Setup menu.
- To ensure correct operation of the EZ VIEW button, you
should set the correct aspect ratio in the Display Setup
menu. (See pages 29 to 31).
WIDE SCREEN
EZ VIEW
If you are using a 16:9 TV
For 16:9 aspect ratio discs
- WIDE SCREEN
Displays the content of the DVD title in 16:9 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the black bars at
the top and bottom of the screen will disappear. The picture
will look vertically stretched. (Depending on a type of disc,
the black bars may not disappear completely.)
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarge
For 4:3 aspect ratio discs
- Normal Wide
Displays the content of the DVD title in 16:9 aspect ratio.
The picture will look horizontally stretched.
- SCREEN FIT
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are
cut off and the central portion of the screen is enlarged.
- Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black bars will
appear at the left and right of the screen in order to prevent
the picture from looking horizontally stretched.
For 16:9 aspect ratio discs
- 4:3 Letter Box
Displays the content of the DVD title in 16:9 aspect ratio.
The black bars will appear at the top and bottom of the screen.
- 4:3 Pan Scan
The left and right portions of the screen are cut off and the
central portion of the 16:9 screen is displayed.
- SCREEN FIT
The top and bottom portions of the screen are cut off and a
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarged.
For 4:3 aspect ratio discs
- Normal Screen
Displays the content of the DVD title in 4:3 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off and the
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are cut
off and the central portion of the screen is enlarged.
Note
This function may behave differently depending on
the type of disc.
Selecting the Audio
Language
You can select a desired audio language quickly
and easily with the AUDIO button.
Using the AUDIO button (DVD/
MPEG4)
1. Press the AUDIO button. The Audio changes when the
button is pressed repeatedly.
The audio languages are DVD
represented by
ENG Dolby Digital 5.1CH
abbreviations.
AUDIO
Press AUDIO button at
remocon repeatedly to
select the desired Audio
on MPEG4 then press
the ENTER .
MPEG4
MP3 1/1
AUDIO
2. To remove the AUDIO icon, press the CANCEL or RETURN
button.
English _19
● ADVANCED FUNCTIONS
To play back using aspect ratio
(DVD)
If you are using a 4:3 TV
Advanced functions
Note
- This function depends on audio languages are
encoded on the disc and may not work.
- A DVD disc can contain up to 8 audio languages.
- To have the same audio language come up
whenever you play a DVD;
Refer to “Using the Audio Language” on page 28.
Selecting the Subtitle
Language
Changing the Camera Angle
When a DVD contains multiple angles of a particular
scene, you can use the ANGLE function.
Using the ANGLE function (DVD)
If the disc contains multiple angles, the ANGLE
appears on the screen.
1. During play or pause mode, press the MENU button on the
remote control.
2. Press the π/† buttons to select Function, then press the
® or ENTER button.
3. Press the π/† buttons to select Angle, then press the
® or ENTER button.
You can select a desired subtitle quickly and
easily with the SUBTITLE button.
Info
Zoom
Bookmark
Using the SUBTITLE button (DVD/
MPEG4)
1. Press the SUBTITLE button. The subtitle languages are
represented by abbreviations.
The subtitle changes when DVD
the button is pressed
ENG
repeatedly.
EZ View
Angle
Enter
Return
Menu
4. Press the √/® buttons or you can use the number buttons
on the remote control to select the desired angle.
4/6
SUBTITLE
External subtitle option will
appear, depends the DivX
Disc.
Note
- If the disc has only one angle, this feature won’t
work. Currently, very few discs have this feature.
- Depending on the disc, these functions may not
work.
MPEG4
Subtitle Selection
External Subtitle Off
readme.TXT
Non-standard fonts are not supported
Enter
Press Subtitle button
at Remote control
repeatedly to select
the desired subtitle
language on a MPEG4.
Return
Menu
MPEG4
Off
SUBTITLE
2. To remove the SUBTITLE icon, press the CANCEL or
RETURN button.
Note
- You have to change the desired subtitle in the
Disc Menu, according to discs. Press the DISC
MENU button.
- This function depends on what subtitles are
encoded on the disc and may not work on all DVDs.
- A DVD disc can contain up to 32 subtitle
languages.
- To have the same subtitle language come up
whenever you play a DVD; Refer to “Using the
Subtitle Language” on page 28.
20_ Advanced functions
Using the Bookmark
Function
This feature lets you bookmark sections of a DVD
so you can quickly find them at a later time.
Using the Bookmark Function
(DVD)
1. During play, press the MENU button on the remote control.
2. Press the π/† buttons to select Function, then press the
® or ENTER button.
Info
Zoom
Bookmark
EZ View
Angle
Enter
Return
Menu
3. Press the π/† buttons to select Bookmark, then press the
® or ENTER button.
- - -
4. When you reach the scene you want to mark, press-the
ENTER button. Up to three scenes may be marked at a time.
CANCEL
1 - -
Recalling a Marked Scene
1~3. The first 1~3 steps are the same as those for “Using the
Bookmark Function”.
4. Press the √/® buttons to select a marked scene.
1 2 3
CANCEL
5. Press the PLAY () button to skip to the marked scene.
Clearing a Bookmark
1~3. The first 1~3 steps are the same as those for “Using the
Bookmark Function”.
4. Press the √/® buttons to select the bookmark number you
want to delete.
5. Press the CANCEL button to delete a bookmark number.
1 2 3
CD Audio or discs with MP3/WMA/JPEG/MPEG4
contain individual songs and/or pictures that can be
organized into folders as shown below. They are
similar to how you use your computer to put files
into different folders.
Off
Stop
Open the disc tray.
Place the disc on the tray.
Close the tray.
The tray closes and this
screen displays.
T
WMA
JPEG
MP3
MPEG4
Enter
-
: Name of currently playing file.
-
: Current Playback Time.
-
CANCEL
Using the Zoom Function
00:00:00
Return
Menu
: Current Playback Mode : There are four
modes. They can be selected in order by
pressing the REPEAT button.
- Off: Normal Playback
- Track: Repeats the current track.
- Folder: Repeats the current folder
- Random: Files in the disc will be played in
random order.
Using the Zoom Function (DVD)
1. During play or pause mode, press the MENU button on the
remote control.
2. Press the π/† buttons to select Function, then press the
® or ENTER button.
3. Press the π/† buttons to select Zoom, then press the
® or ENTER button.
4. Press the π/† or √/® buttons to select the part of the
screen you want to zoom in-on. Press the ENTER button.
- During DVD play, press ENTER to zoom in
2X/4X/2X/Normal in order.
-
: MP3 file icon.
-
: CD Audio file icon.
-
: WMA file icon.
-
: Folder icon.
-
: JPEG file icon
-
: Current Folder icon.
-
: AVI file icon.
Note
- When playing MP3, WMA or JPEG, the Picture
Quality and the HDMI Resolution cannot be set.
- When playing MPEG4 file, the VIDEO SEL. only
works in stop mode.
Info
Zoom
Bookmark
EZ View
Angle
Enter
Return
Menu
English _21
● ADVANCED FUNCTIONS
Clips Menu for MP3/WMA/
JPEG/ MPEG4/CD Audio
Note
- The Bookmark function may not work,
depending on a disc,
Advanced functions
Repeat/Random playback
Folder Selection
The folder can be selected both in Stop or Play mode.
- To select the Parent Folder
Press the RETURN button to go to parent folder, or press
the π/† buttons to select “..” and press ENTER to go to the
parent folder.
- To select the Peer Folder
Press the π/† buttons to select the desired folder, then
press ENTER.
- To select the Sub-Folder
Press the π/† buttons to select the desired folder,
then press ENTER.
WMA
JPE G
Parent Folder
MU SIC
Current Folder
1st
Sub-Folders
2nd
S ON G FILE 1
Peer Folders
S ON G FILE 2
S ON G FILE 3
MP E G4 FILES
MP3/WMA/CD Audio
Playback
1. Open the disc tray. Place the disc on the tray. Close the tray.
- Only one kind of file is played back when a disc or a
folder contains both MP3 and WMA files.
2. Press the π/† or √/® buttons to select a song file.
Press ENTER to begin playback of the song file.
Play
Off
Because You
T
00:00:23
...
Because You
Cactus
Sad Dayu
Wonderful
Enter
22_ Advanced functions
Return
To resume normal play, press the CANCEL button.
CD-R MP3/WMA file
R oot
MP3
Press the REPEAT button to change the playback mode. There
are four modes, such as Off, Track, Folder and Random.
- Off: Normal Playback
- Track: Repeats the current song file.
- Folder: Repeats the song files which have the same
extension in the current folder.
- Random: Song files which have the same extension will be
played in random order.
REPEAT
Repeat
When you record MP3 or WMA files on CD-R, please refer
to the following.
- Your MP3 or WMA files should be ISO 9660 or JOLIET format.
ISO 9660 format and Joliet MP3 or WMA files are compatible
with Microsoft's DOS and Windows, and with Apple's Mac.
This format is the most widely used.
- When naming your MP3 or WMA files, do not exceed 8
characters, and enter “.mp3, .wma” as the file extension.
General name format : Title.mp3. or Title.wma. When
composing your title, make sure that you use 8 characters
or less, have no spaces in the name, and avoid the use of
special characters including: (.,/,\,=,+).
- Use a decompression transfer rate of at least 128 Kbps
when recording MP3 files.
Sound quality with MP3 files basically depends on the rate
of compression/decompression you choose. Getting CD
audio sound requires an analog/digital sampling rate, that is
conversion to MP3 format, of at least 128 Kbps and up to 160
Kbps. However, choosing higher rates, like 192 Kbps or more,
only rarely give better sound quality. Conversely, files with
decompression rates below 128 Kbps will not be played properly.
- Use a decompression transfer rate of at least 64Kbps
when recording WMA files.
Sound quality with WMA files basically depends on the rate of
compression/decompression you choose.
Getting CD audio sound requires an analog/digital sampling
rate, that is conversion to WMA format, of at least 64Kbps
and up to 192Kbps. Conversely, files with decompression
rates below 64Kbps or over 192Kbps will not be played
properly. Sampling rate that can be supported for WMA files
is > 30Khz.
- Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected
to prevent illegal copying. These files are of the following
types: Windows MediaTM (registered trade mark of Microsoft
Inc) and SDMITM (registered trade mark of The SDMI
Foundation). You cannot copy such files.
- Important:
The above recommendations cannot be taken as a
guarantee that the DVD player will play MP3 recordings, or
as an assurance of sound quality. You should note that cer
tain technologies and methods for MP3 file recording on CDRs prevent optimal playback of these files on your DVD player
(degraded sound quality and in some cases, inability of the
player to read the files).
- This unit can play a maximum of 500 files and 500 folders per disc.
CD-R AVI file
MPEG4 Playback
MPEG4 Play Function
AVI files are used to contain the audio and video data. Only
AVI format files with the “.avi” extensions can be played.
1. Open the disc tray. Place the disc on the tray.
DVD-RW & DVD+R
Off
Stop
/MPEG4
T
● ADVANCED FUNCTIONS
Close the tray.
2. Press the π/† or √/® buttons to select an avi file
(DivX/XiviD) and then press ENTER button.
This unit can play the following video compression formats
within the AVI file format:
- DivX 3.11 contents
- DivX 4 contents (Based on MPEG-4 Simple Profile)
- DivX 5 contents (MPEG-4 simple profile plus additional
features such as bi-directional frames. Qpel and GMC are
also supported.)
- XviD MPEG-4 compliant Contents.
Format that support for DivX file :
- Basic DivX format DivX3.11 / 4.12/ 5.x
- Xvid (MPEG-4 compliant video codec) and DivX Pro
- File format : *.avi, *.div, *.divx.
00:00:00
...
a01_divx51b-8
a02_divx505b-8
a03_divx502sp-8
a04_divx412-8
This unit supports all resolutions up to maximum below.
Enter
Return
Menu
Repeat and Repeat A-B playback
Press the REPEAT button to change playback mode. There are
3 modes, such as Off, Folder and Title.
- Folder : repeats the AVI files which have the same extension
in the current folder.
- Title : repeats the title that is playing.
Press the REPEAT A-B button to set the point where you want
repeat play to start (A).
Press the REPEAT A-B button again at the point where you
want the repeat play to stop (B).
- To return to normal play, press the CANCEL button.
Note
- A-B REPEAT does not allow you to set point (B)
until at least 5 second of playback time has
elapsed after point (A) has been set
DivX3.11 & DivX4 & XviD
Bit rate may fluctuate:
Device may skip decoding
the high bit rate portions
and begin decoding again
when Bit rate returns to
normal.
DivX5
720 x 480 @30fps
720 x 576 @25fps
: Maximum bit rate :
4Mbps
Possible warning messages that may appear when trying to
play DivX/AVI files are :
1. No Authorization
- File with bad registration code.
Authorization Error
This player is not authorized
to play this video.
OK
MPEG4 Function Description
Function
Description
During play, press the |k or
Skip
K| button, it moves forward
(|k or K|)
or backward 5 minutes.
During play, press the SEARCH
(k or K) button and press
again to search at a faster
Search
speed. Allows you to search
(k or K)
at a faster speed in an AVI
file. (2X, 4X, 8X)
Allows you to search at a
Slow Motion slower speed in an AVI file.
Play
(1/2X, 1/4X, 1/8X)
Each time the STEP button
Step Motion is pressed, a new frame will
Play
appear.
ZOOM
2X/4X/2X/Normal in order
Reference page
-
Enter
Return
2. Unsupported Codec
- Files with certain Codec Types, Versions
(ex. MP4, AFS and other proprietary codecs) are not
suppoerted by this player.
Off
Stop
-
Sweet Vol 3
T
00:00:20
...
Because You
Cactus
File you attempt to play
has unsupported codec
Sad Dayu
Wonderful
Sweet Vol 3
P 16
Enter
P 16
P 21
Menu
Return
3. Unsupported Resolution
- Files containing resolutions higher than the player’s
specification are not supported.
Off
Stop
/a01_divx51b-8
T
00:00:00
...
- These functions may not work depending on MPEG4 file.
a01_divx51b-8
a02_divx505b-8
File you attempt to play
has unsupported resolution
a03_divx502sp-8
a04_divx412-8
Enter
Return
Menu
English _23
Advanced functions
Note
• The resolution that can be supported by DVD1080P9 model up to 720 x 480 @30 frames/ 720 x
576 @25 frames
• This unit supports CD-R/RW written in MPEG4 in
accordance with the “ISO9660 format”.
Playing Media Files Using
the USB Host feature
You can enjoy the media files such as pictures, movies and
tunes saved in an MP3 player, USB memory or digital
camera in high audio by connecting the storage device to
the USB port of the DVD Player.
Using the USB HOST feature
1. Connect the USB device to the USB port on the front of the unit.
2. Press the USB button, Press the π/† button to
select the one of partition from USB, then Press ENTER.
Disc
USB
Fast playback
To play back the disc at a faster speed, press
(k/K) during playback.
• Each time you press either button, the playback speed will
change as follows : 2x ➞ 4x ➞ 8x.
Compatible Devices
1. USB devices that support USB Mass Storage v1.0.
(USB devices that operate as a removable disk in Windows
(2000 or later) without additional driver installation.)
2. MP3 Player: Flash type MP3 player.
3. Digital camera: Cameras that support USB Mass Storage v1.0.
• Cameras that operate as a removable disk in Windows
(2000 or later) without additional driver installation.
4. USB Flash Drive: Devices that support USB2.0 or USB1.1.
• You may experience a difference in playback quality
when you connect a USB1.1 device.
5. USB card Reader: One slot USB card reader and Multi slot
USB card reader
• Depending on the manufacturer. the USB card reader
may not be supported.
• If you install multiple memory devices into a multi card
reader, you may experience problems.
6. If you use a USB extension cable, the USB device might not
be recognized.
• Supported Formats
3. Press the π/† or √/® buttons to select a file in USB.
Press ENTER to Open file.
Still
Picture
Movie
Enter
Return
Menu
Note
• Each time the USB button on the remote control is
pressed, a frame of the USB device selection will appear.
• “USB” appears on the display screen.
• USB MENU screen appears on the TV screen and the
saved file is played.
Safe USB Removal
To prevent damage to the memory stored in the USB device,
perform safe removal before disconnecting the USB cable.
- Press the STOP (■) button
- Remove the USB cable.
Skip Forward/Back
During playback, press the (|k/K|) button.
• When there is more than one file, when you press the K|
button, the next file is selected.
• When there is more than one file, when you press the |k
button, the previous file is selected.
24_ Advanced functions
File
extension
JPG
MP3
Bit
Rate
Version
Pixel
JPG .JPEG
-
-
640*480
-
.MP3
80~384kbps
-
-
44.1KHz
WMA
.WMA
56~128kbps
V8
-
44.1KHz
VCD
MPG.MPEG
1.5Mbps
VCD1.1,VCD2.0
320*480
44.1KHz
WMV
.WMV
4Mbps
V1,V2,V3,V7
720*480
44.1KHz~48KHz
DivX
.AVI, .ASF
4Mbps
.DivX3.11~DivX5.1,Xvid
720*480
44.1KHz~48KHz
Sampling
Frequency
Music
Off
Stop
File
Name
Note
• VCD & WMV can't be played on this player.
• CBI (Control/Bulk/Interrupt) is not supported.
• Digital Cameras that use PTP protocol or require additional
program installation when connected to a PC are not supported.
• A device using NTFS file system is not supported.
(Only FAT 16/32 (File Allocation Table 16/32) file system is
supported.)
• Some MP3 players, when connected to this product,may not
operate depending on the sector size of their file system.
• The USB HOST function is not supported if a product that
transfers media files by its manufacturer-specific program is
connected.
• Does not operate with Janus enabled MTP(Media Transfer
Protocol) devices.
• The USB host function of this product does not support all
USB devices.
CD Ripping
Picture CD Playback
This feature lets you to copy audio files from disc to USB
device into MP3 format.
Stop
Open the dics tray.
Off
Track 01
T
00:00:00
Track 01
Connect the USB device to the USB
port on the front of the unit.
Track 02
DEV : SELECT ALL
START
Track 03
Track 04
Track 05
ENTER RETURN
Track 06
Track 07
Track 08
Enter
Menu
This screen will displayed.
Note
- Press the STOP button to return to the clips --menu.
- When playing a Kodak Picture CD, the unit
displays the Photo directly, not the clips menu.
- HD-JPEG must be set to SD
1. With the unit in Stop mode, press the ® button to select the
DEV (storage media device) menu, then press ENTER button.
2. Press the π/† buttons to select SELECT, then press the
ENTER button to marked all files to be copying.
Rotation
- To unmarked copying all files press ENTER button
: Each time the ENTER button is pressed, the
picture rotates 90 degrees clockwise.
again.(UNSELECT Menu)
- If you want to marked several files to be copying, press the
√ button, then press ENTER button on the selected file.
Stop
Zoom
: Press the π/† buttons to select the part of the
screen you want to zoom in on.
Press the ENTER button. Each time the ENTER button is pressed, the picture is enlarged up to 2X.
Off
Disc Track 01
T
00:00:00
USB
Track 01
Track 02
DEV : SELECT ALL
START
Track 03
Track 04
Track 05
Track 06
Slide Show
Track 07
Track 08
Enter
Menu
•
3. Press the π/† buttons to select START, then press the
ENTER button.
File copy begins.
- To cancel the copying in progress, press the CANCEL
button.
Play
• Before beginning the Slide Show, the picture interval must
be set.
•
: When this icon is selected and ENTER is
pressed, the pictures change automatically
with about a 6 second interval.
•
: The pictures change automatically with
about a 12 second interval.
•
: The pictures change automatically with
about a 18 second interval.
Off
Track 01
T
00:00:00
Track 01
Track 02
DEV : USB 1
UNSELECT ALL
Track 03
Track 04
Track 05
: The unit enters slide show mode.
CD Ripping START
Track 06
Track 07
CANCEL
Track 08Cancel
Enter
Ripping
REPEAT
Repeat
Note
TIMER :
ENTER RETURN
- When the CD ripping begins, the player
will play automatically.
- Only Audio CD(CD DA) discs can be ripped.
Note
- Depending on a file size, the amount of time
between each picture may be different from the
manual.
- If you don’t press any button, the slide show will
start automatically in about 10 seconds by default.
English _25
● ADVANCED FUNCTIONS
Place the Audio CD(CD DA) disc on
the tray, and close the tray.
1. Select the desired folder.
2. Press the π/† buttons to select a Picture file in the clips
menu and then press the ENTER button.
3. Press the INFO button on the remote control to select the
menu you want to view and then press the ENTER button.
Advanced functions
Picture CD Playback for
HD-JPEG
HDMI must be connected and the resolution should be
720p/1080i/1080p, and HD-JPEG should be in HD mode.
"Please set the HDMI as highest Resolution which you TV
support."
1. Select the desired folder.
Stop
Off
T
00:00:00
Note
- Depending on a file size, the amount of time
between each picture may be different from the
set interval time.
- The image may be displayed at a smaller size
depending on the picture size when displaying
images in HD-JPEG mode.
- It is recommended to set the "BD Wise" to "Off"
In case of playback JPEG image file bigger than
720 X 480 pixel size.
WMA
MP3-JPEG Playback
JPEG
MP3
MPEG4
You can play JPEG using music as a backgound.
Enter
Menu
Return
2. Press the π/† buttons to select a Picture file in the clip
menu and then press the ENTER button.
• Press the STOP (■) button to return to the clips menu.
• When playing a Kodak Picture CD, the unit displays the
Photo directly, not the clips menu.
Stop
Off
00:00:00
1
1. Press the π/† buttons to select an MP3 file in the clips
menu and then press the ENTER button.
2. Press the π/† buttons to select a JPEG file in the
clips menu and then press the ENTER button.
- Music willplay from the beginning
3. Press Stop button when you want to stop the
playback.
Note
MP3 and JPEG files have to be on the same disc.
...
CD-R JPEG Disc
1
2
3
Enter
Return
Menu
Note
- To make the setup menu disappear, press the
MENU button.
• Rotation
Press the √/® button to rotate the screen 90 degrees to
the left/right.
• Skip Picture
Press the |k or K| button to select previous or next
picture.
• Slide Show
Press the PLAY (® ) button to start SLIDE function.
Press the STOP (■) button to stop SLIDE function.
26_ Advanced functions
- Only files with the “.jpg” and “.JPG” extensions can be played.
- If the disc is not closed, it will take longer to start playing and
not all of the recorded files may be played.
- Only CD-R discs with JPEG files in ISO 9660 or Joliet format
can be played.
- The name of the JPEG file may not be longer than 8
characters and should contain no blank spaces or special
characters (. / = +).
- Only a consecutively written multi-session disc can be played.
If there is a blank segment in the multi-session disc, the disc
can be played only up to the blank segment.
- A maximum of 500 images can be stored on a single CD.
- Kodak Picture CDs are recommended.
- When playing a Kodak Picture CD, only the JPEG files in the
pictures folder can be played.
- Kodak Picture CD: The JPEG files in the pictures folder can
be played automatically.
- Konica Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- Fuji Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- QSS Picture CD: The unit may not play QSS Picture CD.
- If the number of files in 1 Disc is over 500, only 500 JPEG
files can be played.
- If the number of folders in 1 Disc is over 500, only JPEG
files in 500 folders can be played
Changing setup menu
Setting Up the Language
Features
Using the Setup Menu
If you set the player menu, disc menu, audio and subtitle
language in advance, they will come up automatically every
time you watch a movie.
1. With the unit in Stop mode, press the MENU button on the
remote control. Use the π/† buttons to select Setup, then
press the ® or ENTER button.
Language Setup
®
Audio Setup
®
Display Setup
®
Parental Setup :
®
DivX(R) Registration
®
Anynet+(HDMI-CEC) : On
Enter
Return
Menu
❶ Language Setup: Setup of the Language.
❷ Audio Setup : Setup of the Audio Options.
❸ Display Setup : Setup of the Display Options. Use to
select which type of screen you want to watch and
several display options.
❹ Parental Setup :-Setup of the Parental Level.
Allows users to set the level necessary to prevent
children from viewing unsuitable movies such as those
with violence, adult subject matter, etc.
❺ DivX(R) Registration : Please use the Registration
code to register this player with the DivX(R) Video On
Demand format.
To learn more go to www.divx.com/vod.
❻ Anynet+(HDMI-CEC): Setup of the Anynet+(HDMI-CEC)
Options.
2. Press the π/† buttons to access the different features.
Press the ® or ENTER button to access the sub features.
3. To make the setup screen disappear after setting up, press
the MENU button again.
Note
Some Setup Menu selections may not work,
Depending on the disc.
Using the Player Menu Language
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ®
or ENTER button.
3. Press the π/† buttons to select Language Setup, then
press the ® or ENTER button.
4. Press the π/† buttons to select Player Menu, then press
the ® or ENTER button.
5. Press the π/† buttons to select the desired language,
then press the ® or ENTER button.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
LANGUAGE SETUP
Player Menu
√ English
Français
Deutsch
Español
Subtitle
Italiano
Nederlands
DivX Subtitle
Disc Menu
Audio
Enter
Return
Menu
Using the Disc Menu Language
This function changes the text language only on the disc
menu screens.
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ®
or ENTER button.
3. Press the π/† buttons to select Language Setup, then
press the ® or ENTER button.
4. Press the π/† buttons to select Disc Menu, then press
the ® or ENTER button.
5. Press the π/† buttons to select the desired language,
then press the ® or ENTER button.
- If the selected language is not recorded on the disc,
the original pre-recorded language is selected.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
LANGUAGE SETUP
Player Menu
Disc Menu
Audio
Subtitle
DivX Subtitle
Enter
√ English
Français
Deutsch
Español
Italiano
Nederlands
Return
Menu
English _27
● CHANGING SETUP MENU
The Setup menu lets you customize your DVD player by
allowing you to select various language preferences, set
up a parental level, even adjust the player to the type of
television screen you have.
Changing setup menu
Using the Audio Language
Using the DivX Subtitle Language
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ®
or ENTER button.
3. Press the π/† buttons to select Language Setup, then
press the ® or ENTER button.
4. Press the π/† buttons to select Audio, then press the ®
or ENTER button.
5. Press the π/† buttons to select the desired language, then
press the ® or ENTER button.
- Select “Original” if you want the default soundtrack
language to be the original language the disc is
recorded in.
- If the selected language is not recorded on the disc, the
original pre-recorded language is selected.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ®
or ENTER button.
3. Press the π/† buttons to select Language Setup,-then
press the ® or ENTER button.
4. Press the π/† buttons to select DivX Subtitle, then press
the ® or ENTER button.
5. Press the π/† buttons to select the desired language,
then press the ® or ENTER button.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
LANGUAGE SETUP
Player Menu
Disc Menu
Audio
Subtitle
DivX Subtitle
Enter
Original
√ English
Français
Deutsch
Español
Italiano
Return
Menu
Using the Subtitle Language
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ®
or ENTER button.
3. Press the π/† buttons to select Language Setup,-then
press the ® or ENTER button.
4. Press the π/† buttons to select Subtitle, then press the ®
or ENTER button.
5. Press the π/† buttons to select the desired -language,
then press the ® or ENTER button.
- Select “Automatic” if you want the subtitle language
to be the same as the language selected as the audio
language.
- Some discs may not contain the language you select
as your initial language; in that case the disc will use its
original language setting.
- The language is selected and the screen returns to
setup menu.
- To make the setup menu disappear, press the MENU
button.
LANGUAGE SETUP
Player Menu
Disc Menu
Audio
Subtitle
DivX Subtitle
Enter
28_ Changing setup menu
√ Automatic
English
Français
Deutsch
Español
Italiano
Return
Menu
LANGUAGE SETUP
Player Menu
Disc Menu
Audio
Subtitle
DivX Subtitle
Enter
√ Unicode
Western
Turkish
Central
Cyrillic
Greek
Return
Menu
Setting Up the Audio
Options
Audio Options allows you to setup the audio device
and sound status settings depending on the audio
system in use.
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ®
or ENTER button.
3. Press the π/† buttons to select Audio Setup, then press
the ® or ENTER button.
4. Press the π/† buttons to select the desired item, then a
press the ® or ENTER button.
Language Setup
®
Audio Setup
®
Display Setup
®
Parental Setup :
®
DivX(R) Registration
®
Anynet+(HDMI-CEC) : On
Enter
Return
Menu
AUDIO SETUP
Digital Out
: PCM
MPEG-2 Digital Out
: PCM
Dynamic Compression : On
PCM Down Sampling
: On
Power On Music
: On
Enter
Return
Menu
Note :
- There is no analogue audio output when you play
a DTS sound disc.
- Even when PCM Down sampling is Off
• Some discs will only output down sampled
audio through the digital outputs.
• To make the Setup menu disappear, press the
MENU button
❺ Power On Music
This menu is used to activate or deactivate the opening
sound when you turn on the DVD player.
- On : To turn On Start up music.
- Off : To turn Off Start up music
HDMI
- If your TV is not compatible with compressed multichannel formats (Dolby Digital, DTS, MPEG), you
should set Digital Audio to PCM.
- If your TV is not compatible with LPCM sampling
rates over 48kHz, you should set PCM Down sampling to On.
Manufactured under licence from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
Setting Up the Display
Options
Display options enable you to set various video functions of
the player.
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ®
or ENTER button.
3. Press the π/† buttons to select Display Setup, then press
the ® or ENTER button.
4. Press the π/† buttons to select the desired item, then
press the ® or ENTER button.
Language Setup
®
Audio Setup
®
Display Setup
®
Parental Setup :
®
DivX(R) Registration
®
Anynet+(HDMI-CEC) : On
Enter
Return
Menu
❶ TV Aspect
Depending on a type of television you have, you may want
to adjust the screen setting (aspect ratio).
- 4:3 Letter Box : Select when you want to see the
total 16:9 ratio screen DVD supplies, even though
you have a TV with a 4:3 ratio screen. Black bars will
appear at the top and bottom of the screen.
- 4:3 Pan&Scan : Select this for conventional size TVs
when you want to see the central portion of the 16:9
screen. (Extreme left and right side of movie picture
will be cut off.)
- 16:9 Wide : You can view the full 16:9 picture on your
wide screen TV.
DISPLAY SETUP
TV Aspect
4:3 Letter Box
Screen Messa
4:3 Pan&Scan
TV System
Video Output √ 16:9 Wide
HDMI
®
Picture Quality
®
Enter
Return
Menu
❷ Screen Messages
Use to turn on-screen messages On or Off.
❸ TV System
- NTSC : In case of using NTSC disc
• If your TV system only has PAL-Video input, you must
choose “PAL”. When you choose “PAL”, Interlace output format is PAL 60 Hz output.
• If your TV system only has NTSC, input you must
choose “NTSC ”.
• If you set up the NTSC TV, HDMI output frame rate
is 60 Hz.
- PAL : In case of using PAL disc
• If your TV system only has NTSC-Video input, you
must choose “NTSC”.
• If your TV system only has PAL input, you must
choose “PAL ”.
• If you set up the PAL TV, HDMI output frame rate is 50 Hz.
- Auto
DISPLAY SETUP
TV Aspect
: Wide
Screen Messages : On
NTSC
TV System
PAL
Video Output
√ Auto
HDMI
Picture Quality
®
Enter
Return
Menu
English _29
● CHANGING SETUP MENU
❶ Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bit stream : Outputs Dolby Digital via the digital output.
Select Bit stream when connecting to a Dolby Digital
Decoder.
❷ MPEG-2 Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bit stream : Converts to MPEG-2 Digital Bit stream
(5.1CH). Select Bit stream when using the Digital Audio
Output.
❸ Dynamic Compression
- On : To select dynamic compression.
- Off : To select the standard range.
❹ PCM Down Sampling
- On : Select this when the Amplifier connected to the
player is not 96KHz compatible. In this case, the
96KHz signals will be down converted to 48KHZ.
- Off : Select this when the Amplifier connected to the
player is 96KHz compatible. In this case, all signals will
be output without any changes.
Changing setup menu
❹ Video Output
Setting Up the BD Wise
Select Video Output.
- I-SCAN : Select when you want to use Component
Interlace Out.
- P-SCAN : Select when you want to use Component
Progressive Out.
- SCART-RGB : Select when you want to use SCART
RGB Out. (It does not function in NTSC mode).
- SCART-CVBS : Select when you want to CVBS output
from scart connection. It does not function in Progressive
mode. (It does not function in NTSC mode).
• If you press the VIDEO SEL. button, Video output
mode is changed in regular sequence in no disc
mode.
(I-SCAN ➝ P-SCAN ➝ SCART-RGB ➝ SCART-CVBS)
• If the Yes/No selection in the Display Setup sub
Menu is not made within 10 seconds, the screen
returns to the previous menu.
When the player is connected to a SAMSUNG TV which
supports “BD Wise”,you can enjoy optimized Picture Quality
by setting the “BD Wise” function as “On”.
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ®
or ENTER button.
3. Press the π/† buttons to select Display Setup, then press
the ® or ENTER button.
4. Press the π/† buttons to select HDMI, then press
the ® or ENTER button.
5. Press the π/† buttons to select BD-Wise, then press the
® or ENTER button.
Press the π/† buttons to select On, then press the ® or
ENTER button.
HDMI SETUP
Resolution Setting : Auto
Resolution
: 576p
HD-JPEG
: SD
BD-Wise
TV Aspect
: Wide
Screen Messages : On
TV System
: Auto
I-SCAN
Video Output
P-SCAN
HDMI
√ SCART-RGB
Picture Qualit
SCART-CVBS
Enter
Return
Off: Off
√ On
DISPLAY SETUP
Enter
Return
Menu
HDMI SETUP
Resolution Setting : Auto
Menu
Resolution
: BD-Wise
HD-JPEG
: SD
BD-Wise
: On
➎ HDMI
This setting is used when the unit is connected by HDMI
with Display devices (TV, projector, etc).
- Resolution Setting
- Auto : Resolution setting automatically
- Manual : Resolution setting manually
- Resolution
- 480p/576p : 720 x 480, 720 x 576
- 720p : 1280 x 720
- 1080i : 1920 x 1080
- 1080p : 1920 x 1080
- HD-JPEG
• HD : High Definition image source
- Available when resolution is 720p/1080i in HDMI
enabled.
• SD : Standard Definition image source.
- BD-Wise
HDMI SETUP
Resolution Setting : Auto
Resolution
: 576p
HD-JPEG
: SD
BD-Wise
: Off
Enter
Return
Note
This option can be changed only when TV support
BD Wise.
How to turn Off the BD Wise
If you wish to change to other resolution when "BD Wise On",
Please choose a method between these two as follows :
Method 1
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ®
or ENTER button.
3. Press the π/† buttons to select Display Setup, then press
the ® or ENTER button.
4. Press the π/† buttons to select HDMI, then press
the ® or ENTER button.
5. Press the π/† buttons to select resolution you wish to use,
then press the ® or ENTER button.
HDMI SETUP
Resolution Setting : Manual
Resolution
HD-JPEG
Enter
Return
Menu
Menu
BD-Wise
√
: BD Wise
576P
720p
: SD
1080i
: On
1080p
BD-Wise
Enter
Return
Menu
Please choose "Yes" to continue, otherwise choose "No"
to keep current setting.
30_ Changing setup menu
HDMI SETUP
Do you want to turn off
BD Wise Mode and change to
selected Resolution?
Yes
No
❻ Picture Quality
- Black Level : Adjusts the brightness of the screen.(On
or Off) It does not function in PAL and Auto mode.
- Brightness : Level 1 ~ Level 5
- Contrast : Level 1 ~ Level 5
Enter
Return
Menu
- Color Saturation : Level 1 ~ Level 5
PICTURE QUALITY
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ®
or ENTER button.
3. Press the π/† buttons to select Display Setup, then press
the ® or ENTER button.
4. Press the π/† buttons to select HDMI, then press
the ® or ENTER button.
5. Press the π/† buttons to select BD-Wise, then press the
® or ENTER button.
Press the π/† buttons to select Off, then press the ® or
ENTER button.
HDMI SETUP
Resolution Setting : Auto
Resolution
: 1080p
HD-JPEG
: SD
BD-Wise
Enter
√ Off: Off
On
Return
Menu
The HDMI resolution will be changed to maximum
resolution supported by your TV.
HDMI SETUP
Resolution Setting : Auto
Resolution
: 1080p
HD-JPEG
: SD
BD-Wise
: Off
Enter
Return
Black Level
: Off
Brightness
: Level 3
Contrast
: Level 3
Color Saturation
: Level 3
Enter
Return
Menu
• Consult your TV User’s Manual to find
out if your TV supports Progressive Scan. If
Progressive Scan is supported, follow the TV
User’s Manual regarding Progressive Scan
settings in the TV’s menu system.
• If Video Output is set incorrectly, the screen
may be blocked.
• The resolutions available for HDMI output
depend on the connected TV or projector.
For details, see the user’s manual of your TV
or projector.
• When the resolution is changed during playback, it may take a few seconds for a normal
image to appear.
• If you set the HDMI output resolution
720p,1080p or 1080i, HDMI output provides
better picture quality.
Menu
Note :
- It is recommended to set the "BD Wise" to "Off"
In case of playback JPEG image file bigger than
720 X 480 pixel size.
English _31
● CHANGING SETUP MENU
Method 2
Changing setup menu
Setting Up the Parental
Control
The Parental Control function works in conjunction
with DVDs that have been assigned a rating, which
helps you control the types of DVDs that your family
watches. There are up to 8 rating levels on a disc.
Setting Up the Rating Level
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ®
or ENTER button.
To make the setup menu disappear, press the
MENU button. For example, if you select up to
Level 6, discs that contain Level 7,8 will not play.
Changing the Password
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ®
or ENTER button.
Language Setup
®
Audio Setup
®
Display Setup
®
Parental Setup :
®
®
Language Setup
®
DivX(R) Registration
Audio Setup
®
Anynet+(HDMI-CEC) : On
Display Setup
®
Parental Setup :
®
DivX(R) Registration
®
Anynet+(HDMI-CEC) : On
Enter
Return
Enter
Return
Menu
3. Press the π/† buttons to select Parental Setup, then
press the ® or ENTER button.
Menu
3. Press the π/† buttons to select Parental Setup, then
press the ® or ENTER button.
Language Setup
®
Audio Setup
®
Display Setup
®
Parental Setup :
®
®
Language Setup
®
DivX(R) Registration
Audio Setup
®
Anynet+(HDMI-CEC) : On
Display Setup
®
Parental Setup :
®
DivX(R) Registration
®
Anynet+(HDMI-CEC) : On
Enter
Return
Menu
4. Press the π/† buttons to select Rating Level, then press
the ® or ENTER button.
PARENTAL SETUP
Rating Level
: Kids Safe
Enter
Return
Menu
4. Press the π/† button to select Change Password, then
press the ® or ENTER button. Enter your new password.
Re-enter the new password again.
PARENTAL SETUP
Rating Level
:Kids Safe
Change Password
Change Password
Enter
Enter
Return
Return
Menu
Menu
5. Enter your password.
- By default, password-is set to 0000. Please change
password to other than 0000 to activate parental
control function.
PARENTAL SETUP
Rating Level
Enter Password
PARENTAL SETUP
Rating Level
:Kids Safe
Change Password
: Kids Safe
Change Password
Enter
Return
Menu
Enter Password
PARENTAL SETUP
Rating Level
Enter
Return
Menu
6. Press the π/† buttons to select the Rating Level you want,
then press the ® or ENTER button.
e.g) Setting up in Kids Safe.
PARENTAL SETUP
Rating Level
Change Passwor
Enter
32_ Changing setup menu
Return
√ Kids Safe
Level 2
Level 3
Level 4
Level 5
Level 6
Menu
:Kids Safe
Change Password
Enter New Password
Enter
Return
Menu
Note
If you have forgotten your password, see
“Forgot Password” in the Troubleshooting Guide.
Setting Up the
Anynet+(HDMI-CEC)
Anynet+ is a function that can be used to operate
the unit using a Samsung TV remote control, by
connecting the DVD 1080P9 to a SAMSUNG TV
using a HDMI Cable. (see page 13 to 14) (This is
only available with SAMSUNG TVs that support
Anynet+.
DVDP
View TV
®
Select Device
®
Record
®
Menu on Device
®
®
®
Setup
®
Select On when you connect the DVD 1080P9 with
Samsung TV that support Anynet+.
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ®
or ENTER button.
Language Setup
®
Audio Setup
®
Display Setup
®
Parental Setup :
®
DivX(R) Registration
®
ENTER
TV Menu
To make the setup menu disappear, press the
MENU button.
• You can operate the DVD Player by using TV remote
control. (TV buttons that can be used to control the DVD
Player :
,
,
,
,
,
and
,
Anynet+(HDMI-CEC) : On
Enter
Return
buttons,
Menu
buttons.
- Select Device : Use this option to select device.
3. Press the π/† buttons to select Anynet+(HDMI-CEC),
then press the ® or ENTER button.
- Menu on Device : Same as MENU button on the
DVD Player remote control.
Language Setup
®
Audio Setup
®
Display Setup
®
Parental Setup :
®
DivX(R) Registration
®
Anynet+(HDMI-CEC) : On
Enter
Return
• If you play a DVD when the TV power is off, the TV
will power On.
Language Setup
®
Audio Setup
®
Display Setup
®
Parental Setup :
®
DivX(R) Registration
Off
Anynet+(HDMI-CEC)
√ On : On
®
Return
Note
• By pressing the PLAY button of the unit while
watching TV, the TV screen will change to the play
screen.
Menu
4. Set the Anynet+(HDMI-CEC) to “On” on your DVD Player,
then press the ® or ENTER button.
Enter
- Device Operation : Same as INFO button on the
DVD Player remote control.
Menu
• If you turn the TV off , the DVD Player will power
off automatically.
• If you change the HDMI to other sources (Compos
ite,Component,... etc) in TV while playing the DVD
disc, the DVD Player will stop playing.
5. Set the Anynet+ function at your TV. (See the TV instruction
manual for more information.).
• When you press Anynet+ button on the TV remote
control, the below OSD will appear.
English _33
● CHANGING SETUP MENU
Device Operation
Receiver : Off
Move
Exit
Reference
Firmware upgrade
2. Press the √/® buttons to select Total, then press the
ENTER button.
Introduction
Samsung will often support the software upgrade to
improve the performance of this unit to the latest status, through Samsung Internet Site (www.samsung.
com).
Because the specially new mpeg4 codec continues and
is on-going, any improvements that are made depend
on the upgrade software you are using as well as the
software that your DVD-player contained before the
upgrade.
How to make an upgrade disc
Write the downloaded file onto a blank CD-R or CDRW disc, using the following settings:
1. You have to download a new file through Download Center
of Samsung Internet Site (www.samsung.com).
2. Write the file to Disc using CD-RW of your computer.
Note
- File System CD-ROM ISO Level
- Character set ISO 9660
- Finalized, single session
- Write speed low
Upgrade procedure
1. Open the disc tray. Place the disc on the tray. Close the
tray. The Firmware upgrade screen appears.
Old Version : 081118.I6.B.1080P9XEG
New Version : 081212.V1.B.1080P9XEG
Firmware upgrade
appears on the display
34_ reference
Old Version : 081118.I6.B.1080P9XEG
New Version : 081212.V1.B.1080P9XEG
Firmware upgrade starts
- In the middle of the writing, the tray will open
automatically. After taking out the disc, please wait for
about 2 minutes.
- If the unit was succesfully updated, the unit will turn off,
and on, after closing the tray automatically. When the
unit turns on, this screen will display.
3. Press the number buttons to select the desired language
Press
Touche
Drücken Sie
Pulsar
Premere
Druk op
1
2
3
4
5
6
for English
pour Français
für Deutsch
para Español
per Italiano
voor Nederlands
Note
- If the “Select Menu Language” doesn’t appear,
please contact to “Samsung Service Center”.
- Do not press any button and unplug the power
code during upgrade.
- The upgrade procedure may change, refer to
the web site (www.samsung.com).
Troubleshooting
Before requesting service (troubleshooting), please check the following.
Problem
Action
Page
• Check the batteries in the remote control. They may need replacing.
• Operate the remote control at a distance of no more than 20 feat.
• Remove batteries and hold down one or more buttons for several
minutes to drain the microprocessor inside the remote control to the
reset it. Reinstall batteries and try to operate the remote control again.
P3
Disc does not play.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
P5
The
icon appears
on screen.
•
1.
2.
3.
4.
Disc Menu Doesn't
appear.
• Check if the disc has menu.
Play mode differs
from the Setup Menu
selection.
• Some of the functions selected in the Setup Menu may not work properly if the
disc is not encoded with the corresponding function.
P27 ~ 33
The change ratio
cannot be changed.
• The Screen Ratio is fixed on your DVDs.
P29 ~ 31
No audio.
• Make sure you have selected the correct DIgital Output in the Audio Options Menu.
P28 ~ 29
The screen is
blocked.
• Press the
button (on the front panel) for more than 5 seconds with no disc
in the player. All settings will revert to factory settings.
P16
Forgot password.
• Press the
button (on the front panel) for more than 5 seconds with no disc
in the player. All setings will revert to factory settings.
Don't use this unless absolutely necessary.
P32
If you experience
other problems
• Go to the contens and find the section of the instruction book that contains the
explanation regarding the current problem. Follow the procedure once again.
• If the problem still cannot be solved, please contact your nearest authorized
service centre.
The picture is noisy
or distorted.
• Make sure that the disc is not dirty or scratched.
• Clean the disc.
No HDMI output
• Check the Video output is HDMI enabled.
• Check the connection between the TV and the HDMI jack of DVD player.
• See if the TV supports this 480p/576p/720p/1080i/1080p DVD player.
P13 ~ 14
Abnormal HDMI
output screen.
• If snow noise appears on the screen, it means that TV does not support HDCP
(High-bandwidth Digital Content Protection).
P13 ~ 14
HDMI output Jitter
• Check your TV system setup correctly.
• The screen Jitter phenomenon may occur when frame rate is converted from 50Hz
to 60 Hz for 720p/1080i/1080p HDMI (High Definition Multimedia Interface) Output.
• Please refer to the user's manual of your TV.
P29 ~ 31
The features or action cannot be completed at this time because :
The DVD's software restricts it.
The DVD's software doesn't support the feature (e.g., angles).
The feature is not available at the moment.
You've requested a title or chapter number or search time that is out of range.
P2
English _35
● REFERENCE
No operation can be
performed with the
remote control.
Reference
Specifications
Power Requirements
Power Consumption
General
Weight
Dimensions
Operating Temperature Range
Operating Humidity Range
DVD
(DIGITAL VERSATILE DISC)
Disc
AC110~240V, 50/60Hz
8W
1.6 Kg
430mm (W) X 203mm (D) X 45mm (H)
+5ºC to +35ºC
10 % to 75 %
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
CD : 12CM
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
CD : 8CM
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
Composite Video
1 channel : 1.0 Vp-p (75 Ω load)
SCART Jack
Video
Output
Component Video
HDMI
Output terminal
Audio
* Maximum Output Level
Output
*Frequency Response
*Digital Audio Out
R(Red) : 0.7 Vp-p (75 Ω load)
G(Green) : 0.7 Vp-p (75 Ω load)
B(Blue) : 0.7 Vp-p (75 Ω load)
Composite Video : 1.0 Vp-p (75 Ω load)
Luminance Signal : 1.0 Vp-p (75 Ω load)
Colour Signal : 0.3 Vp-p (75 Ω load)
Y : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
480p, 576p, 720p, 1080p, 1080i
RCA, SCART
2Vrms
20 Hz to 20 kHz
Coaxial terminal (S/PDIF)
* : Nominal specification
Note
- Samsung Electronics Co., Ltd reserves the right to change the specifications with out notice.
- Weight and dimensions are approximate.
36_ reference
UNITED KINGDOM
This Samsung product is warranted for the period of
twelve (12) months from the original date of
purchase, against defective materials and
workmanship. In the event that warranty service is
required, you should return the product to the retailer
from whom it was purchased.
However, Samsung Authorised Dealers and
Authorised Service Centres in other EC Countries will
comply with the warranty on the terms issued to
purchasers in the country concerned.
In case of difficulty, details of our Authorised Service
Centres are available from:
Samsung Electronics U.K. Ltd.
Customer Care Centre PO Box 17243 Edinburgh,
EH11 4YB United Kingdom
United Kingdom
Tel : 0845 SAMSUNG (7267864)
Fax : 0845 650 8080
Web : www.samsung.com
EIRE
Tel : 0818 717 100
Fax : +44 (0)131 202 0630
Web : www.samsung.com
„ WARRANTY CONDITIONS
1. The warranty is only valid if, when warranty service
is required, the warranty card is fully and properly
completed and is presented with the original invoice
or sales slip or confirmation, and the serial number
on the product has not been defaced.
2. Samsung’s obligations are limited to the repair or,
at its discretion, replacement of the product or the
defective part.
3. Warranty repairs must be carried out by Authorised
Samsung Dealers or Authorised Service Centres.
No re-imbursement will be made for repairs carried
out by non Samsung Dealers and, any such repair
work and damage to the products caused by such
repair work will not be covered by this warranty.
EIRE
4. This product is not considered to be defective
in materials nor workmanship by reason that it
requires adaptation in order to conform to national
or local technical or safety standards in force in
any Country other than the one for which the
product was originally designed and manufactured.
This warranty will not cover, and no re-imbursement will be made for such adaptation nor any
damage which may result.
5. This warranty covers none of the following:
a) Periodic check ups, maintenance and repair or
replacement of parts due to normal wear and
tear.
b) Cost relating to transport, removal or installation
of the product.
c) Misuse, including the faiure to use this product
for its normal purposes or incorrect installation.
d) Damage caused by Lightning, Water, Fire, Acts
of God, War, Public Disturbances, incorrect
mains voltage, improper ventilation or any other
cause beyond the control of Samsung.
6. This warranty is valid for any person who legally
acquired possession of the product during the
warranty period.
7. The consumers statutory rights in any applicable
national legislation whether against the retailer
arising from the purchase contract or otherwise
are not affected by this warranty. Unless there is
national legislation to the contrary, the rights under
this warranty are the consumers sole rights and
Samsung, its subsidiaries and distributors shall not
be liable for indirect or consequential loss or any
damage to records, compact discs, videos or audio
taper or any other related equipment or material.
SAMSUNG ELECTRONICS (U.K.) LTD.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
Region
North America
Latin America
Country
CANADA
MEXICO
U.S.A
ARGENTINE
BRAZIL
CHILE
NICARAGUA
HONDURAS
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
COLOMBIA
BELGIUM
CZECH REPUBLIC
DENMARK
FINLAND
FRANCE
Europe
CIS
Asia Pacific
Middle East &
Africa
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
EIRE
AUSTRIA
SWITZERLAND
RUSSIA
KAZAKHSTAN
UZBEKISTAN
KYRGYZSTAN
TADJIKISTAN
UKRAINE
LITHUANIA
LATVIA
ESTONIA
AUSTRALIA
NEW ZEALAND
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
PHILIPPINES
SINGAPORE
THAILAND
TAIWAN
VIETNAM
TURKEY
SOUTH AFRICA
U.A.E
Contact Center 1-800-SAMSUNG(726-7864)
01-800-SAMSUNG(726-7864)
1-800-SAMSUNG(726-7864)
0800-333-3733
0800-124-421, 4004-0000
800-SAMSUNG(726-7864)
00-1800-5077267
800-7919267
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-SAMSUNG(726-7864)
0-800-100-5303
01-8000112112
02 201 2418
800-726-786 (800 - SAMSUNG)
70 70 19 70
030-6227 515
3260 SAMSUNG (€ 0,15/Min)
08 25 08 65 65 (€ 0,15/Min)
01805 - SAMSUNG(726-7864 € 0,14/Min)
06-80-SAMSUNG(726-7864)
800-SAMSUNG(726-7864)
02 261 03 710
0900-SAMSUNG (726-7864 € 0,10/Min)
815-56 480
0 801 801 881, 022-607-93-33
80820-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
902-1-SAMSU(72678)
0771-400 200
0845 SAMSUNG (7267864)
0818 717 100
0800-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
8-800-555-55-55
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
8-800-502-0000
8-800-77777
8000-7267
800-7267
1300 362 603
0800 SAMSUNG (0800 726 786)
800-810-5858, 400-810-5858, 010-6475 1880
3698-4698
3030 8282, 1800 110011, 1-800-3000-8282
0800-112-8888
0120-327-527
1800-88-9999
1800-10-SAMSUNG(726-7864)
1800-SAMSUNG(726-7864)
1800-29-3232, 02-689-3232
0800-329-999
1 800 588 889
444 77 11
0860-SAMSUNG(726-7864 )
800-SAMSUNG (726-7864), 8000-4726
Web Site
www.samsung.com/ca
www.samsung.com/mx
www.samsung.com/us
www.samsung.com/ar
www.samsung.com/br
www.samsung.com/cl
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com.co
www.samsung.com/be
www.samsung.com/cz
www.samsung.com/dk
www.samsung.com/fi
www.samsung.com/fr
www.samsung.de
www.samsung.com/hu
www.samsung.com/it
www.samsung.com/lu
www.samsung.com/nl
www.samsung.com/no
www.samsung.com/pl
www.samsung.com/pt
www.samsung.com/sk
www.samsung.com/es
www.samsung.com/se
www.samsung.com/uk
www.samsung.com/ie
www.samsung.com/at
www.samsung.com/ch
www.samsung.ru
www.samsung.com/kz_ru
www.samsung.com/kz_ru
www.samsung.ua
www.samsung.lt
www.samsung.com/lv
www.samsung.ee
www.samsung.com/au
www.samsung.com/nz
www.samsung.com/cn
www.samsung.com/hk
www.samsung.com/in
www.samsung.com/id
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/ph
www.samsung.com/sg
www.samsung.com/th
www.samsung.com/tw
www.samsung.com/vn
www.samsung.com/tr
www.samsung.com/za
www.samsung.com/ae
Memo
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these
items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office,
for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed
of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb
indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If
batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste
and recycle them through your local, free battery return system.
AK68-01750K(01)