NEW_W1_XC12U_ENG_MFL38343854
MODEL : XC12
XC12U
ENGLISH
There is so much your Hi-Fi system can do
Record from a CD
or radio to cassette
Go to page 8
Lull me to sleep
and wake me up
Go to page 9
Contents
Setting up
3
About Player
4
About Remote control
5
Listening to CDs
6
Connecting your portable USB player - OPTIONAL 6
Listen to cassette tapes
7
Listening to the radio
7
Recording
8
Listening to music from your portable player
8
Setting the Clock
9
Use your player as an alarm clock
9
About MP3/WMA
9
Safety Precaution
10
Troubleshooting
11
Specifications
11
Play CDs and
cassettes
Play from many
external devices
Go to page 8
Go to pages 6 & 7
Portable CD player
Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely.
2
MICRO Hi-Fi SYSTEM ] USER GUIDE
MP3 player
ENGLISH
Setting up
2 Fit the AM loop aerial to its stand
Connect the AM loop aerial to the player.
3 Connect the FM aerial
The reception will be at its best when the two loose
ends of the aerial are in a straight line and horizontal.
4 Plug the power plug into a wall socket
1 Connect the speaker cables to the player
Cables from the left-hand speaker connect to the terminal
marked L (left) + (plus) and - (minus). Cables from the
right-hand speaker are connected to the terminal marked
R (right) + (plus) and - (minus).
To connect the cable to the player, press each of the four
square plastic finger pads on the rear of the player. The
connector will open ready to receive a cable.
Put the battery in the remote control
Make sure that the + (plus) and - (minus) on the
battery (size AAA) match those on the remote
control.
MICRO Hi-Fi SYSTEM ] USER GUIDE
3
About Player
Z PUSH (CD door)
You can use it when inserting or removing CDs.
Don't open the door while CD plays back.
MODE/RIF
This will change the tuner from stereo to mono
and usually improve the reception.
VOLUME
Control the volume when using any function.
PHONES (Headphone jack)
Connect a headphone plug ( 3.5 mm) into the
jack to listen to the sound through headphones.
Connecting headphones (not supplied) will
switch off the speakers.
CLOCK
For setting the clock and checking the time.
(see Setting the Clock)
TIMER
With the TIMER function you can turn CD play
and radio reception on or off at a desired time.
(see Use your player as an alarm clock)
Use when playing a cassette tape
4
MICRO Hi-Fi SYSTEM ] USER GUIDE
eXtreme Dynamic Sound System
Reinforce the treble, bass and surround sound
effect. XDSS ON will show in the display.
Press again for XDSS OFF.
Sound quality adjustment
You can choose between 4 fixed sound
impressions. Select a desired sound mode by
using EQ.
(FLAT → ROCK → POP → CLASSIC)
RDS (OPTIONAL) /SET
RDS shows information about radio stations.
(see Listening to the radio)
SET confirms the time you have selected
when setting the clock. (see Setting the clock)
USB connector - OPTIONAL
Connect a remote USB compatible player
here.
OPTIMIZER
Optimizes compressible MP3 files so that it
improves the bass sound.
(MP3 - OPT ON → MP3 - OPT OFF)
About Remote control
Fall asleep while listening to your player
Firstly, start a radio station or music. Press
SLEEP one or more times to select delay
time between 10 and 90 minutes, after the
player will turn off.
Turn on or off
Search for a folder of MP3/WMA files
When a CD containing MP3/WMA files in
several folders is being played, press
PRESET/FOLDER to select the folder you
want to play.
Choose a ‘preset number’ for a radio
station (see Listening to the radio)
eXtreme Dynamic Sound System
Reinforce the treble, bass and surround
sound effect.
Moving to other cards - OPTIONAL
In case that more than two memory cards are
connected to the USB port, press D.SKIP to
select a card you want to use.
Use when playing a CD
Sound quality adjustment
You can choose between 4 fixed sound
impressions.
See information about your music
MP3/WMA files often come with tags. The tag
gives the Title, Artist, Album or Time information. Press MP3 Info while a file is playing to
see this information.
Temporarily stop the sound
Press the button again to return to the sound.
To change the functions
Change the functions between FM, AM, CD,
PORTABLE, TAPE, USB (OPTIONAL) etc.
For storing radio stations
If you have saved radio stations using
PROGRAM/MEMO, you can scroll through
them and select one.
(see Listening to the radio)
Listen to your tracks in any order
(see Listening to the CDs)
This button is not available.
Listen to your tracks again and again
Press REPEAT once to repeat the track
currently playing. Press REPEAT twice to
repeat the whole CD, or if you’re listening to
the whole folder of MP3/WMA CD. The display will show what is being repeated.
MICRO Hi-Fi SYSTEM ] USER GUIDE
5
Listening to CDs
ON PLAYER
1. Open the CD door:
2. Insert the CD:
Label facing up.
3. Close the CD door:
The display will show the total
number of tracks (files).
4. Select the CD function:
5. Start the CD playing:
6. To stop a CD playing:
ON REMOTE
Z PUSH
The advantage of connecting your portable USB player through the
system’s USB port is that the portable device can be controlled from
the system. Connect the portable player to the system using a USB
cable (not supplied).
Z PUSH
FUNCTION
FUNCTION
B/[]
STOP CLEAR
B/[]
x
Listening to CDs - more you can do
Pause or restart a CD
Press B/[] during playback. Press this button again to resume play.
Search for a section within a track
Hold ./> on the front panel or .bb/BB> on the remote control
during playback. (This function is only available for Audio CD’s.)
Speed search for tracks
Hold ./> on the front panel or .bb/BB> on the remote control.
Track skips continuously in turn. For Audio CD, track skips continuously in
turn only on stop mode.
Skip to another track
Press ./> on the front panel or .bb/BB> on the remote control.
Listen to your tracks in any order
Up to 20 tracks on a CD can be listened to in the order of your choice.
Insert a CD and wait for it to be read. Press PROGRAM MEMORY on the
front panel or PROGRAM/MEMO on the remote control, then use ./>
on the front panel or .bb/BB> on the remote control to select the
track. Press PROGRAM MEMORY or PROGRAM/MEMO again to save
and select the next track. Press B/[]. To clear your selection, press STOP
CLEAR (or x ), PROGRAM MEMORY (or PROGRAM/MEMO), STOP
CLEAR (or x ).
6
MICRO Hi-Fi SYSTEM ] USER GUIDE
Connecting your portable
USB player - OPTIONAL
1. Select the USB function:
2. The display will show
CHECKING, followed by the
number of files displayed:
3. Press:
4. Before disconnecting the
portable USB player, change to
any other function by pressing:
5. Remove the USB player:
ON PLAYER
ON REMOTE
FUNCTION
FUNCTION
B/[]
FUNCTION
B/[]
FUNCTION
NOTE : Some portable devices are not compatible with this system.
Listening to the radio - more you can do
Listen to cassette tapes
ON PLAYER
1. Open the tape door:
2. Insert the tape:
3. Close the tape door:
4. Select the TAPE function:
5. Start the tape playing:
6. To stop a tape playing:
Look for radio stations automatically
ON REMOTE
xZ
Press - TUNING + (or TUN.- /TUN.+ ) for more than 0.5 second. The tuner
will scan automatically and stop when it finds a radio station.
Delete all the saved stations
FUNCTION
FUNCTION
B
xZ
Listen to cassette tapes - more you can do
To Play Fast backward or Forward
After pressing bb/BB during playback, or stop, press B at a point you
want.
Press and hold PROGRAM MEMORY or PROGRAM/MEMO for two seconds. “CLEAR” shows. Press STOP CLEAR (or x ) to erase all the saved
stations.
Choose a ‘preset number’ for a radio station
Select a station you want by pressing - TUNING + or TUN.- /TUN.+. Press
PROGRAM MEMORY or PROGRAM/MEMO, the station flashes.
Press - PRESET + or PRESET/FOLDER to select the preset number you
want. Press PROGRAM MEMORY or PROGRAM/MEMO to save it.
Improve poor FM reception
Press MODE/RIF on the front panel. This will change the tuner from stereo
to mono and usually improve the reception.
See information about your radio stations - OPTIONAL
Listening to the radio
Make sure both the FM and AM aerials are connected.
1. Select either FM or AM:
2. Select the radio station:
3. To ‘save’ a radio station:
A preset number will show in
the display.
4. To select a ‘saved’ station:
5. To confirm press:
Up to 50 radio stations can be
saved.
ON PLAYER
ON REMOTE
TUNER/BAND
- TUNING +
PROGRAM
MEMORY
FUNCTION
TUN.- / TUN.+
PROGRAM/MEMO
- PRESET +
PROGRAM
MEMORY
PRESET/FOLDER
PROGRAM/MEMO
The FM tuner is supplied with the Radio Data System (RDS) facility. This
shows the letters RDS on the display, plus information about the radio station being listened to. Press RDS on the front panel several times to view
the information.
PTY - Programme Type, such as News, Sport, Jazz Music.
RT - Radio Text, the name of the radio station.
CT - Time Control, the time at the location of the radio station.
PS - Programme Service name, the name of channel.
You can search the radio stations by programme type by pressing
- PRESET +. The display will show the last PTY in use. Press - PRESET +
one or more times to select your preferred programme type. Press and
hold - TUNING +. The tuner will search automatically. When a station is
found the search will stop.
MICRO Hi-Fi SYSTEM ] USER GUIDE
7
Listening to music from
your portable player
Recording
Record from a CD or radio to cassette
ON PLAYER
1. Open the tape door:
2. Insert a blank tape:
3. Close the tape door:
4. Select a mode (FM/AM, CD,
PORTABLE or USB (OPTIONAL))
in which you want to record:
- For CD, press B/[].
5. Start the Recording:
6. To stop a Recording:
ON REMOTE
xZ
FUNCTION
The player can be used to play the music from many types of portable
player.
FUNCTION
z
xZ
CD Synchronized Recording
ON PLAYER
1. Open the tape door:
2. Insert a blank tape:
3. Select the CD function:
4. Start the Recording:
The synchronized recording is
started automatically after about
7 seconds.
5. To stop a Recording:
8
MICRO Hi-Fi SYSTEM ] USER GUIDE
ON REMOTE
xZ
FUNCTION
z
xZ
FUNCTION
1. Connect the portable player
by plugging the unit into
PORTABLE IN on the back of
the player.
2. Turn the power on:
3. Select the PORTABLE
function:
4. Turn the portable player on
and start it playing:
ON PLAYER
ON REMOTE
1 /]]
FUNCTION
POWER
FUNCTION
Use your player as an alarm clock
Setting the Clock
ON PLAYER
1. Turn the power on:
2. Press for at least 2 seconds:
3. Choose from either:
AM 12:00 (for an am and pm display) or 0:00 (for a
24 hour display)
4. Confirm your selection:
5. Select the hours:
6. Press:
7. Select the minutes:
8. Press:
1 /]]
CLOCK
- TUNING +
SET
- TUNING +
SET
- TUNING +
SET
Press and hold TIMER for two seconds. Each function, TUNER, CD, USB
(in the USB supplied models) flashes for two seconds. Press SET when
the function you want to be woken by is showing.
If you choose TUNER you will be shown the stations you have saved as
presets. Use - TUNING + to select the station you want, then press SET.
You will be shown the ON TIME display. This is where you set the time you
want the alarm to go off. Use - TUNING + to change the hours and minutes
and SET to save.
You will then be shown the OFF TIME display. This is where you set the
time you want the function to stop. Use - TUNING + to change the hours
and minutes and press SET to save.
Next you will be shown the volume (VOL) you want to be woken by.
Use - TUNING + to change the volume and SET to save. Switch the system off. The clock icon shows that the alarm is set.
When the system is turned off you can check the time the alarm is set for
by pressing TIMER. You can also turn the alarm on and off by pressing
TIMER. To set the alarm to go off at a different time, switch the system on
and reprogramme following the same steps as initially.
About MP3/WMA
MP3/WMA Disc compatibility with this unit is limited as follows:
• Sampling Frequency : 8 - 48 kHz (MP3), 32 - 48 kHz (WMA)
• Bit rate : 8 - 320 kbps (MP3), 48 - 320 kbps (WMA)
• CD-R physical format should be “ISO 9660”
• If you record MP3/WMA files using the software which cannot create a
FILE SYSTEM, for example “Direct-CD” etc., it is impossible to playback
MP3 files. We recommend that you use “Easy-CD Creator”, which creates
an ISO 9660 file system.
• File names should be named using 30 letters or less and must incorporate “.mp3”,“.wma” extension e.g. “********.MP3” or “********.WMA”
• Do not use special letters such as “/ : * ? “ < >”etc.
• Even if the total number of files on the disc has more than 1000, it will
only be shown up to 999.
MICRO Hi-Fi SYSTEM ] USER GUIDE
9
Safety Precaution
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is intended to
alert the user to the presence of uninsulated dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects
filled with liquids, such as vases, should be placed on the apparatus.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit;
That is, a single outlet circuit which powers only that appliance and has no additional outlets or
branch circuits. Check the specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these
conditions could result in electric shock or fire. Periodically examine the cord of your appliance,
and if its appearance indicates damage or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where
the cord exits the appliance.
To disconnect power from the mains, pull out the mains cord plug. When installing the product,
ensure that the plug is easily accessible.
Disposal of your old appliance
WARNING: Do not install this equipment in a confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of
the product and to protect it from over heating.
The openings should be never be blocked by placing the product on a bed, sofa, rug or other
similar surface. This product should not be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the manufacturer's instruction has been adhered to.
1. When this crossed-out wheeled bin symbol is attached to a product it means the
product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the
municipal waste stream via designated collection facilities appointed by the
government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact
your city office, waste disposal service or the shop where you purchased the product.
This product is manufactured to comply with EMC Directive 2004/108/EC and Low
Voltage Directive 2006/95/EC.
CAUTION:
This product employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain it for
future reference. Should the unit require maintenance, contact an authorized service center.
Use of controls, adjustments or the performance of procedures other than those specified herein
may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation
when open. DO NOT STARE INTO BEAM.
10
MICRO Hi-Fi SYSTEM ] USER GUIDE
European representative :
LG Electronics Service Europe B.V. Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : +31-036-547-8940)
Troubleshooting
Symptom
No power.
No sound.
The unit does not
start playback.
The remote
control does not
work properly.
Unable to record.
Specifications
Cause
Correction
• The power cord is disconnected.
• Plug the power cord into the wall
outlet securely.
• The power of the external source • Switch on the external source
equipment is turned off.
equipment.
• The speaker cable is connected
• Set the speaker cable to the corto a wrong position.
rect position, then turn on the unit
again by pressing POWER.
• An unplayable disc is inserted.
• Insert a playable disc.
• The disc is placed upside down.
• Place the disc with the playback
side down.
• The disc is not placed within the
• Place the disc on the disc tray
guide.
correctly inside the guide.
• The disc is dirty.
• Clean the disc.
• The remote control is not pointed • Point the remote control at the
at the remote sensor of the unit.
remote sensor of the unit.
• The remote control is too far from • Operate the remote control within
the unit.
about 23 ft (7 m).
• There is an obstacle in the path
• Remove the obstacle.
of the remote control and the unit.
• The battery in the remote control • Replace the battery with new
is exhausted.
one.
• Record protect tabs are removed. • Cover holes on back edge of tape
with tap.
General
Net Weight
2.3kg
External dimensions (WxHxD) 146 x 238 x 251 mm
Tuner
FM Tuning Range
AM Tuning Range
87.5 - 108.0 MHz or 65 - 74 MHz,
87.5 - 108.0 MHz
522 - 1620 kHz or 520 - 1720 kHz
Amplifier
Output Power
T.H.D
Frequency Response
Signal-to-noise ratio
5W+5W
0.5 %
60 - 20000 Hz
60 dB
CD
Frequency response
Signal-to-noise ratio
Dynamic range
100 - 18000 Hz
55 dB
50 dB
Cassette tape player
F.F/REW Time
Frequency Response
Signal to Noise Ratio
Channel Separation
Erase Ratio
120 sec (C-60)
250 - 8000 Hz
40 dB
30 dB (P/B)/30 dB (R/P)
50 dB (MTT-5511)
Speakers (XCS12F)
Type
Impedance
Frequency Response
Sound Pressure Level
Rated Input Power
Max. Input Power
Net Dimensions (WxHxD)
Net Weight (1EA)
1 Way 1 Speaker
4Ω
100 - 18000 Hz
82 dB/W (1m)
5W
10 W
144 x 238 x 134 mm
1.29 kg
Designs and specifications are subject to change without notice.
MICRO Hi-Fi SYSTEM ] USER GUIDE
11
P/NO : MFL38343854