bintec RS232bw
Universal router with integrated ADSL 2+ modem, ISDN and 11n WLAN
The bintec RS232bw is a powerful and, thanks to its comprehensive equipment, flexible router. The integrated ADSL 2+
modem on the RS232b supports Annex B (ADSL over ISDN), which is predominantly used in Germany, in accordance
with ITU G992.1 and is compatible with Deutsche Telekom's U-R2 connection.
The router in the fan-free metal housing guarantees long-term reliability in critical corporate applications and is ideal for
use as an access router in SMEs, branch offices and home offices. In addition to the integrated ADSL 2+ modem, the
device has five Gigabit Ethernet ports, which can be configured for LAN, WAN or DMZ, and comes with a licence for
five hardware-accelerated IPSec tunnels. The built-in ISDN BRI interface and the UMTS USB modem connected to the
USB port can be used as a remote configuration access and as an ISDN backup interface.
The bintec RS232bw also has a dual band WLAN module with 2.4 and 5 GHz, which supports IEEE 802.11n. The new
802.11n technology permits gross transmission speeds of up to 300 Mbps and offers a better range than the previous
802.11g technology.
Thanks to the integrated IEEE 802.11n compatibility mode, the bintec RS232bw is compatible with all IEEE 802.11g
and IEEE 802.11abgh clients and supports the mixed operation of IEEE 802.11n clients and IEEE 802.11b/g or IEEE
802.11a/h clients. This enables the seamless exchange of existing WLAN routers through the bintec RS232bw without
significant changes to the infrastructure. Clients that already support 802.11n benefit automatically from the higher data
throughput.
Using functions flexibly
Only a few functions are required to forward data packets between two networks. The bintec RS232bw has features
that go far beyond just routing and allow it to be integrated into complex IT infrastructures. By using Extended Routing
and NAT (ERN) the data can be routed in IP routing according to criteria such as IP protocols (Layer 4), source or
destination IP address, source or destination port, TOS/DSCP, source or destination interface and the status of the
destination interface. In addition, you can also use network address translation to translate the data traffic for both
inbound and outbound connections and individually for each interface based on a wide range of criteria.
The comprehensive multicast support makes the device ideal for use in multimedia and streaming applications.
The Stateful Inspection Firewall (SIF) offers effective protection against attacks from the Internet through dynamic
packet filtering. Firewall handling is made easier through numerous pre-configured services. An optional content filter
rounds off the security functions of the devices*. In this case, all the outgoing Internet enquiries are classified and allow
contents not wanted to be reliably filtered out.
The basic equipment of the RS Series also offers a SIP application level gateway (ALG) for the direct connection of IP
telephones in the network or for registering with a VoIP provider, without affecting the security of the WAN connection.
The corresponding releases in NAT and the internal Stateful Inspection Firewall are controlled automatically by ALG for
the length of the communication.
Quality of Service is more than a watchword in FEC devices. Thanks to the rising convergence between voice and data,
the classification of data streams is gaining in importance. Our routers provide corresponding QoS mechanisms for
prioritising the VoIP traffic ahead of normal internet traffic, for example, and to guarantee it sufficient bandwidth.
Alternatively you can give normal data traffic priority over e-mail traffic. The bintec QoS implementation allows voice
data to be processed before e-mal data, for example, within a VPN tunnel.
The DNS proxy function supports the LAN for address implementation and the automated IP configuration of PCs is
carried out over an integrated DHCP server.
Remote CAPI is available for the joint use of various ISDN services.
Comprehensive IPSec implementation
The IPSec implementation integrated in bintec RS232bw works not only with preshared keys but also with certificates.
This allows a public key infrastructure to be created for maximum security. (The German Federal Office for Information
Security also recommends the use of certificates.)
Furthermore, the bintec IPSec implementation offers support when creating VPN connections with dynamic IP
addresses: Even small branch offices can be reached without having to be permanently online. If both VPN nodes only
have dynamic IP addresses, confidential information can continue. The exchange of IP addresses is carried out either
over dynamic DNS providers or directly over ISDN. The actual dynamic IP address is transferred either in the ISDN
D-channel (free of charge) or, if this is not possible, in the ISDN B-channel (at cost).
Load Balancing/Backup
The devices offer a unique level of flexibility thanks to the wide variety of interfaces supported. The bintec RS232bw
supports the ability to configure two interfaces as WAN interfaces. As a result, there is not only more bandwidth
available, but there is the opportunity to spread data traffic across individual WAN connections according to load or
data type. Equally, you can use a connection (e.g. SDSL) for the VPN connection to the head office and use a second
WAN port for a low-cost ADSL connection to guarantee the company's other data traffic. If either connection fails, the
other can take over the entire data transfer. In the event that both lines fail, data traffic can automatically be routed over
a UMTS modem connected to the USB port.
Simple configuration and maintenance
The router is configured over the Funkwerk Configuration Interface (FCI), using the integrated configuration wizards for
example. The FCI is a web-based graphic user surface that you can use from any PC with an up-to-date Web browser
via an HTTP or encrypted HTTPS connection. It also offers the opportunity to manage the devices locally and remotely
over other configuration accesses such as Telnet, SSH, ISDN Login and GSM dialin (only possible if USB UMTS
modem is connected).
DIME Manager from Funkwerk Enterprise Communications (FEC) is a free tool for managing FEC devices.
Dime Manager is aimed at administrators who manage networks with up to 50 devices. The software simplifies the
management and configuration of routers or access points either individually or in logical groups.
When developing DIME Manager, simple and efficient operation was the primary aim. It allows, for example, software
updates or configurations to be applied to individual devices or groups of devices simply by drag and drop. DIME
Manager recognises and manages new devices in the network using SNMP multicasts, in other words independent of
their current IP address.
* Content filtering is a fee-paying service and is available as a 30-day trial version.
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RS232bw
09.09.2010
Subject to technical
alterations
Wireless LAN Features
Feature
Description
WLAN Mode
Access Point
WLAN standards
802.11n (Mimo 2x3); 802.11b; 802.11g; 802.11a; 802.11h
Frequency bands 2.4 GHz
indoor/outdoor (EU)
2.4 GHz Indoor/Outdoor (2412-2472 MHz) max. 100 mW EiRP. This information is related to
the permitted transmission power in Germany. The permitted transmission power may vary in
other countries.
Frequency bands 5 GHz indoor (EU)
5 GHz indoor (5150-5350 MHz) max. 200 mW EiRP allowed. This information is related to the
permitted transmission power in Germany. The permitted transmission power may vary in
other countries.
Frequency bands 5 GHz outdoor (EU) 5 GHz outdoor (5470-5725 MHz) max. 200 mW EiRP allowed. This information is related to
the permitted transmission power in Germany. The permitted transmission power may vary in
other countries.
WLAN modes
2.4 GHz operation: 802.11b only; 802.11g only, 802.11b/g/n mixed; 802.11b/g/n mixed long;
802.11b/g/b mixed short; 802.11b/g/n; 802.11g/n; 802.11n only; 5 GHz Operation: 802.11a
only; 802.11a/n; 802.11n only
Automatic Rate Selection (ARS)
Available
Transmission rate
Automatic fallback or fixed transmission rate selectable
Data rates for 802.11a,h (5 GHz)
54, 48, 36, 24, 18, 12, 9 and 6 Mbps (OFDM modulation)
Data rates for 802.11n (2.4 / 5 GHz)
MSC0-15 enables physical rates up to 150 Mbps at 20 MHz channels bandwidth, 2 streams,
short guard interval; MSC0-15 enables physical data rates up to 300 Mbps at 40 MHz
channels bandwidth, 2 streams, short guard interval
Roaming (access point mode)
Seamless roaming with IAPP (artem Inter Access Point Protocol)
Number of spatial streams (802.11n)
1 or 2
Broadcast SSID
On/off switchable
Broadcast SSID
Data prioritization for TOS data, 802.11e/WMM
WMM 802.11e Power Save
Support of active WLAN clients, which support 802.11e power save
Country-specific settings
Channel settings according regulatory domain (802.11d) permitted.
WDS
Wireless Distribution System: Include high security TKIP and AES, interoperable with other
devices from the Funkwerk-EC portfolio (not bintec W500)
TPC
TPC (transmission power control): For 5 GHz, automatic reduction of transmission power
according EN301893
Data rates for 802.11b,g (2.4 GHz)
11, 5.5, 2 und 1 Mbps (DSSS modulation); 54, 48, 36, 24, 18, 12, 9 and 6 Mbps (OFDM
modulation)
Fast roaming 802.1x (access point
mode)
Power Managment for Clients
Pre authentication and PMK caching allows fast roaming by 802.1x encryption
Buffer pool
For cushioning of peaks
Bandwidth (802.11n)
20/40 MHz (bundling of two adjoining 20 MHz channels to one 40 MHz channel)
Short guard interval (802.11n)
On/off switchable; increase of throughput by reduction of the guard intervals from 800ns to
400ns
RTS/CTS
RTS/CTS threshold adjustable
DTIM Period
Adjustable
VLAN
Network segments on layer2 possible. Per SSID one VLAN ID available. Static VLAN
configuration according IEEE 802.1q; up to 32 VLANs supported.
Multi SSID
Depending on the complexity of configuration up to 8 service sets per radio module, with
virtual access points and own MAC address per SSID.
Inter Cell Repeating
Inter traffic blocking for public hot spot (PHS) applications for preventing of communication
radio client to radio client in a single radio cell.
Registering of up to 250 clients simultaneously in access point mode.
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RS232bw
09.09.2010
Subject to technical
alterations
Wireless LAN Electric Characteristics
Feature
Description
Receiver Sensitivity @ 2.4 GHz
802.11b/g
1 Mbps -91 dBm; 2 Mbps -90 dBm; 5.5 Mbps -89 dBm; 11 Mbps -88 dBm; 6 Mbps -90 dBm;9
Mbps -89 dBm; 12 Mbps -88 dBm; 18 Mbps -86 dBm; 24 Mbps -83 dBm; 36 Mbps -80 dBm;
48 Mbps -76 dBm; 54 Mbps -74 dBm
Receiver Sensitivity @ 2.4 GHz
802.11n 20 MHz
MSC0 -89 dBm; MSC1 -87 dBm; MCS2 -85 dBm; MCS3 -82 dBm; MCS4 -79 dBm; MSC5 -75
dBm; MCS6 -73 dBm; MCS7 -70 dBm; MCS8 -83 dBm; MCS9 -84 dBm; MCS10 -81 dBm;
MCS11 -79 dBm; MCS12 -80 dBm; MCS13 -72 dBm; MCS14 -68 dBm; MCS15 -67 dBm
Receiver Sensitivity @ 2.4 GHz
802.11n 40 MHz
MSC0 -87 dBm; MSC1 -84 dBm; MCS2 -82 dBm; MCS3 -79 dBm; MCS4 -75 dBm; MSC5 -71
dBm; MCS6 -69 dBm; MCS7 -67 dBm; MCS8 -86 dBm; MCS9 -83 dBm; MCS10 -79 dBm;
MCS11 -77 dBm; MCS12 -74 dBm; MCS13 -69 dBm; MCS14 -67 dBm; MCS15 -65 dBm
Receiver Sensitivity @ 5 GHz
802.11n 20 MHz
MSC0 -88 dBm; MSC1 -85 dBm; MCS2 -83 dBm; MCS3 -81 dBm; MCS4 -78 dBm; MSC5 -74
dBm; MCS6 -72 dBm; MCS7 -70 dBm; MCS8 -88 dBm; MCS9 -85 dBm; MCS10 -83 dBm;
MCS11 -80 dBm; MCS12 -77 dBm; MCS13 -72 dBm; MCS14 -70 dBm; MCS15 -68 dBm
Receiver Sensitivity @ 5 GHz
802.11a/h
6 Mbps -88 dBm; 9 Mbps -87 dBm; 12 Mbps -86 dBm; 18 Mbps -84 dBm; 24 Mbps -82 dBm;
36 Mbps -78 dBm; 48 Mbps -74 dBm; 54 Mbps -73 dBm
Output power (without antenna gain)
Adjustable in following steps: 5, 8,11,14,16 und 17.5 dBm. Maximal power varies depending
on data rate and frequency band.
Tx Power @ 2.4 GHz 802.11b/g
1 Mbps 16 dBm; 2 Mbps 16 dBm; 5.5 Mbps 16 dBm; 11 Mbps 16 dBm; 6 Mbps 17,5 dBm; 9
Mbps 17,5 dBm; 12 Mbps 17 dBm; 18 Mbps 17 dBm; 24 Mbps 15 dBm; 36 Mbps 15 dBm; 48
Mbps 13 dBm; 54 Mbps 13 dBm
Tx Power @ 2.4 GHz 802.11n 20
MHz/40 MHz
MSC0 17.5 dBm; MSC1 17,5 dBm; MCS2 17 dBm; MCS3 17 dBm; MCS4 15 dBm; MSC5 15
dBm; MCS6 13 dBm; MCS7 13 dBm; MCS8 17.5 dBm; MCS9 17.5 dBm; MCS10 17 dBm;
MCS11 17 dBm; MCS12 15 dBm; MCS13 15 dBm; MCS14 13 dBm; MCS15 13 dBm
Tx Power @ 5 GHz 802.11b/g
1 Mbps 16 dBm; 2 Mbps 16 dBm; 5.5 Mbps 16 dBm; 11 Mbps 16 dBm; 6 Mbps 17.5 dBm; 9
Mbps 17.5 dBm; 12 Mbps 17 dBm; 18 Mbps 17 dBm; 24 Mbps 15 dBm; 36 Mbps 15 dBm; 48
Mbps 13 dBm; 54 Mbps 13 dBm
Tx Power @ 5 GHz 802.11n 20
MHz/40 MHz
MSC0 17.5 dBm; MSC1 17.5 dBm; MCS2 17 dBm; MCS3 17 dBm; MCS4 15 dBm; MSC5 15
dBm; MCS6 13 dBm; MCS7 13 dBm; MCS8 17.5 dBm; MCS9 17.5 dBm; MCS10 17 dBm;
MCS11 17 dBm; MCS12 15 dBm; MCS13 15 dBm; MCS14 13 dBm; MCS15 13 dBm
DSL Interface
Feature
Description
ADSL
ADSL over ISDN (ITU G.992.1 Annex B, ISDN - compatible to U-R2 connection of Deutschen
Telekom), G.Lite (ITU G.922.2)
ADSL 2 / ADSL 2+
ADSL over ISDN (ITU G.992.3, ITU G.992.5 Annex B)
ADSL
Support of Dying Gasp
ATM
Support of layer 1 protocol AAL5 , PVCs, RFC 1483
ATM
Support of up to 7 virtual channels (VC)
ATM
Support of OAM F4/F5 line monitoring
ATM
Support of ATM traffic management (COS - CBR, VBR, UBR)
ISDN Interface
Feature
Description
CAPI
CAPI 2.0 with CAPI user concept (password for CAPI use)
ISDN protocols
Euro-ISDN (Point-to-mulitpoint/Point-to-point), 1TR6 and other national ISDN protocols
ISDN auto-configuration
Automatic recognition and configuration of ISDN protocols
ISDN leased lines
Supported leased lines: D64S, D64S2, TS02, D64S2Y
B channel protocols
Excellent interoperability with other manufacturers (Raw HDLC, CISCO HDLC, X.75)
X.31 over CAPI
Support for various connection paths: X.31/A for ISDN D-channel, X.31/A+B for ISDN
B-channel, X.25 within ISDN B-channel (also leased lines)
Bit rate adaption
V.110 (1,200 up to 38,400 bps), V.120 up to 57,600 kbps (HSCSD) for connection to GSM
subscribers
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RS232bw
09.09.2010
Subject to technical
alterations
VPN
Feature
Description
PPTP (PAC/PNS)
Point to Point Tunneling Protocol for establishing fo Virtual Privat Networks, inclusive strong
encryption methods with 128 Bit (MPPE) up to 168 Bit (DES/3DES, Blowfish)
GRE v.0
Generic Routing Encapsulation V.0 according RFC 2784 for common encapsulation
L2TP
Layer 2 tunnelling protocol inclusive PPP user authentication
Number of VPN tunnels
Inclusive 5 active VPN tunnels with the protocols IPSec, PPTP, L2TP and GRE v.0 (also in
combination possible)
IPSec
Internet Protocol Security establishing of VPN connections
Number of IPSec tunnels
Inclusive 5 active IPSec tunnels
IPSec Algorithms
DES (64 Bit), 3DES (192 Bit), AES (128,192,256 Bit), CAST (128 Bit), Blowfish (128-448 Bit),
Twofish (256 Bit); MD-5, SHA-1, RipeMD160, Tiger192 Hashes
IPSec hardware acceleration
Integrated hardware acceleration for IPSec encryption algorithms DES, 3DES, AES
IPSec IKE
IPSec key exchange via preshared keys or certificates
IPSec IKE Config Mode
IKE Config Mode server enables dynamic assignment of IP addresses from the address pool
of the company. IKE Config Mode client enables the router, to get assigned dynamically an IP
address.
IPSec IKE XAUTH (Client/Server)
Internet Key Exchange protocol Extended Authenticaion client for login to XAUTH server and
XAUTH server for loging of XAUTH clients
IPSec IKE XAUTH (Client/Server)
Inclusive the forwarding to a RADIUS-OTP (One Time Password) server (supported OTP
solutions see www.funkwerk-ec.com).
IPSec NAT-T
Support of NAT-Traversal (Nat-T) for the application at VPN lines with NAT
IPSec IPComp
IPSec IPComp data compression for higher data throughput via LZS
IPSec certificates (PKI)
Support of X.509 multi-level certificates compatible to Micrososft and Open SSL CA server;
upload of PKCS#7/8/10/12 files via TFTP, HTTP, HTTP, LDAP, file upload and manual via FCI
IPSec SCEP
Certificates management via SCEP (Simple Certificate Enrollment Protocol)
IPSec Certificate Revocation Lists
(CRL)
IPSec Dead Peer Detection (DPD)
Support of remote CRLs on a server via LDAP or local CRLs
IPSec dynamic IP via ISDN
Transmission of dynamic IP address in ISDN D or B channel; free-of-charge licence necessary
IPSec dynamic DNS
Enables the registering of dynamic IP addresses by a dynamic DNS provider for establishing a
IPSec connection.
IPSec RADIUS
Authentication of IPSec connections at a RADIUS server. Additionally the IPSec peers, which
were configured on a RADIUS server, can be loaded into the gateway (RADIUS dialout).
IPSec Multi User
Enables the Dial-in of several IPSec clients via a single IPSec peer configuration entry
IPSec QoS
The possibility to operate Quality of Service (traffic shaping) inside of an IPSec tunnel
IPSec NAT
By activating of NAT on an IPSec connection it is possible, to implement several remote
locations with identical local IP addess networks in different IP nets for the VPN connection
IPSec throughput (1400)
34 Mbps with 1400 Byte packets with AES 256 / AES 128 / 3 DES encryption
IPSec throughput (256)
11 Mbps with 256 Byte packets with AES 256 / AES 128 / 3 DES encryption
Continuous control of IPSec connection
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RS232bw
09.09.2010
Subject to technical
alterations
Security
Feature
Description
Encryption WEP/WPA
WEP64 (40 Bit key), WEP128 (104 Bit key), WPA Personal, WPA Enterprise, WPA2 Personal,
WPA2 Enterprise
Inter Cell Repeating
Inter traffic blocking for public hot spot (PHS) applications for preventing of communication
radio client to radio client in a single radio cell.
IEEE802.11i Authentisierung und
Verschlüsselung
802.1x/EAP-MD5, 802.1x/EAP-TLS, 802.1x/EAP-TTLS, 802.1x/EAP-PEAP, key management,
PSK/TKIP encryption, AES encryption, 802.1x/EAP
Access Control List (ACL)
MAC address filter for WLAN clients
VLAN
Network segmentation on layer 2 possible, one VLAN ID per SSID. Static VLAN configuration
according to IEEE 802.1q; supports up to 32 VLANs.
NAT/PAT
Symmetric Network and Port Address Translation (NAT/PAT) with randomly generated ports
inclusive Multi NAT (1:1 translation of whole networks)
Policy based NAT/PAT
Network and Port Address Translation via different criteria like IP protocols, source/destination
IP Address, source/destination port
Policy based NAT/PAT
For incoming and outgoing connections and for each interface variable configurable
Content Filtering
Optional ISS/Cobion Content filter (30 day test license inclusive)
Stateful Inspection Firewall
Packet filtering depending on the direction with controling and interpretation of each single
connection status
Packet Filter
Filtering of IP packets according to different criteria like IP protocols, source/destination IP
address, source/destination port, TOS/DSCP, layer 2 priority for each interface variable
configurable
Routing
Feature
Description
Policy based Routing
Extended routing (Policy Based Routing) depending of diffent criteria like IP protocols
(Layer4), source/destination IP address, source/destination port, TOS/DSCP,
source/destination interface and destination interface status
Multicast IGMP
Support of Internet Group Management Protocol (IGMP v1, v2, v3) for the simultaneous
distribution of IP packets to several stations
Multicast IGMP Proxy
For easy forwarding of multicast packets via dedicated interfaces
Multicast inside IPSec tunnel
Enables the transmission of multicast packets via an IPSec tunnel
RIP
Support of RIPv1 and RIPv2, separated configurable for each interface
Extended RIP
Triggerd RIP updates according RFC 2091 and 2453, Poisened Rerverse for a better
distribution of the routes; furthermore the possibility to define RIP filters for each interface.
Routing throughput (1518)
199 Mbps with 1518 Byte packets
Routing throughput (256)
198 Mbps with 256 Byte packets
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RS232bw
09.09.2010
Subject to technical
alterations
Protocols / Encapsulations
Feature
Description
PPP/MLPPP
Support of Point to Point Protocol (PPP) for establishing of standard PPP connections,
inclusive the Multilink extension MLPPP for the bundeling of several connections
PPPoE (Server/Client)
Point-to-Point Protocol over Ethernet (Client and Server) for establisching of PPP connections
via Ethernet/DSL (RFC 2516)
MLPPPoE (Server/Client)
Multilink extension MLPPPoE for bundeling several PPPoE connections (only if both sides
support MLPPPoE)
PPPoA
Point to Point Protocol over ATM for establishing of PPP connections via ATM/DSL
IPoA
Enables the easy routing of IP via ATM
DNS
DNS client, DSN server, DNS relay and DNS proxy
DYN DNS
Enables the registering of dynamic assigned IP addresses at adynamic DNS provider, e.g. for
establishing of VPN connections
DNS Forwarding
Enables the forwarding of DNS requests of free configurable domains to assigned DNS
server.
DHCP
DHCP Client, Server, Proxy and Relay for siplified TCP/IP configuration
Packet size controling
Adaption of PMTU or automatic packet size controling via fragmentation
QoS
Feature
Description
Policy based Traffic Shapping
Dynamic bandwidth management via IP traffic shaping
Bandwidth reservation
Dynamic reservation of bandwidth, allocation of guaranteed and maximum bandwidths
DiffServ
Priority Queuing of packets on the basis of the DiffServ/TOS field
Layer2/3 tagging
Conversion of 802.1p layer 2 priorisation information to layer 3 diffserv attributes
TCP Download Rate Control
For reservation of bandwidth for VoIP connections
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RS232bw
09.09.2010
Subject to technical
alterations
Redundancy / Loadbalancing
Feature
Description
BoD
Bandwidth on Demand: dynamic bandwidth to suit data traffic load
Load Balancing
Static and dynamic load balancing to several WAN connections on IP layer
VPN backup
Simple VPN backup via different media. Additional enables the Funkwerk interface based VPN
concept the application of routing protocols for VPN connections.
Layer 2 Functionality
Feature
Description
Bridging
Support of layer 2 bridging with the possibility of separation of network segment via the
configuration of bridge groups
VLAN
Support of up to 32 VLAN (Virtual LAN) for segmentation of the network in independent virtual
segments (workgroups)
Proxy ARP
Enables the router to answer ARP requests for hosts, which are accessible via the router. That
enables the remote clients to use an IP address from the local net.
Logging / Monitoring / Reporting
Feature
Description
Internal system logging
Syslog storage in RAM, display via web-based configuration user interface (http/https), filter
for subsystem, level, message
External system logging
Syslog, several syslog server with different syslog level configurable
E-Mail alert
Automatic E-Mail alert by definable events
SNMP traps
SNMP traps (v1, v2, v3) configurable
Activity Monitor
Sending of information to a PC on which Brickware is installed
IPSec monitoring
Display of IPSec tunnel and IPSec statistic; output via web-based configuration user interface
(http/https)
Interfaces monitoring
Statistic information of all pysical and logical interfaces (ETH0, ETH1, SSIDx, ...), output via
web-based configuration user interface (http/https)
WLAN monitoring
Detailed display for radio, VSS, WDS links, bridge links, client links.
WLAN Monitoring
Display for each link: MAC address, IP address, TX packets, RX packets, signal strength for
all receiver antennas, signal-to-noise ratio, data rate; output via web-based configuration user
interface (http/https)
ISDN monitoring
Display of active and past ISDN connections; output via web-based configuration user
interface (http/https)
IP accounting
Detailed IP accounting, source, destination, port, interface and packet/bytes counter,
transmission also via syslog protocol to syslog server
ISDN accounting
Detailed ongoing recording of ISDN connection parameter like calling number and charging
information, transmission also via syslog protocol to syslog server
RADIUS accounting
RADIUS accounting for PPP, PPTP, PPPoE and ISDN dialup connections
Keep Alive Monitoring
Control of hosts/connections via ICMP polling
Tracing
Detailed traces can be done for different protocols e.g. ISDN, PPPoE, ... generation local on
the device and remote via DIME manager
Tracing
Traces can be stored in PCAP format, so that import to different open source trace tools (e.g.
wireshark) is possible.
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RS232bw
09.09.2010
Subject to technical
alterations
Administration / Management
Feature
Description
RADIUS
Central check of access authorization at one or several RADIUS server, RADIUS (PPP, IPSec
inclusive X-Auth and login authentication)
RADIUS dialout
On a RADIUS server configured PPP und IPSec connection can be loaded into the gateway
(RADIUS dialout).
TACACS+
Support of TACACS+ server for login authentication and for shell comando authorization
Time synchronization
The device system time can be obtained via ISDN and from a SNTP server (up to 3 time
server configurable). The obtained time can also be transmitted per SNTP to SNTP clients.
Automatic Time Settings
Time zone profiles are configurable. That enables an automatic change from summer to winter
time.
Supported management systems
DIME Manager, XAdmin
Configurable scheduler
Configuring of time and event controlled tasks, e.g. reboot device, activate/deactivate
interface, activate/deactivate WLAN, trigger SW update and configuration backup
Funkwerk Configuration Interface
(FCI)
Integrated web server for web-based configuration via HTTP or HTTPS. This user interface is
by most of Funkwerk EC products identical.
Software update
Software updates are free of charge; update via local files, HTTP, TFTP or via direct access to
the FEC web server
Remote maintenance
Remote maintenance via telnet, SSL, SSH, HTTP, HTTPS and SNMP (V1,V2,V3)
Configuration via serial interface
Serial configuariton interface is available
ISDN remote maintenance
Remote maintenance via ISDN dial-in with checking of the calling number. The ISDN remote
maintenance connection between two funkwerk devices can be encrypted.
ISDN remote maintenance
A transparent mode enables transmissions of configurations and software updates
respectively
GSM remote maintenance
Remote maintenance via GSM login (external USB UMTS (3G) modem required)
Device discovery function
Device discovery via SNMP multicast.
On The Fly configuration
No reboot after reconfiguration required
SNMP
SNMP (v1, v2, v3), USM model, VACM views, SNMP traps (v1, v2, v3) configurable, SNMP IP
access list configurable
SNMP configuration
Complete management with MIB-II, MIB 802.11, Enterprise MIB
Configuration export and import
Load and save configurations, optional encrypted; optional automatic control via scheduler
SSH login
Supports SSH V1.5 and SSH V2.0 for secure connections of terminal applications
HP OpenView
Integration into Network Node Manager
XAdmin
Support of XAdmin roll out and configuration managemant tool for larger router installations
(IP+ISDN+GSM)
Interfaces
Feature
Description
Ethernet
5 x 10/100/1000 Mbps Ethernet Twisted Pair, autosensing, Auto MDI/MDI-X, up to 4 ports can
be switches as additional WAN ports incl. load balancing, all Ethernet ports can be configured
as LAN or WAN.
WLAN
IEEE 802.11a/b/g/n; 1 radio module, 2.4 und 5 GHz band, 3 external antennas
USB 2.0 host
USB 2.0 full speed host port for connecting UMTS (3G) USB modem sticks (supported sticks:
see www.funkwerk-ec.com)
Serial console
Serial console interface / COM port (mini USB)
ADSL/ADSL 2+
ADSL over ISDN (compatible to U-R2 connection of Deutsche Telekom)
ISDN Basic Rate (BRI)
1 x BRI (TE), 2 B channels
External WLAN antenna connectors
Three reverse SMA antenna connectors for external WLAN antennas
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RS232bw
09.09.2010
Subject to technical
alterations
Hardware Features
Feature
Description
Realtime clock
System time persists even at power failure for some hours.
Wall mounting
Integrated in housing
Environment
Temperature range: Operational 0°C to 40°C; storage -10°C to 70°C; Max. rel. humidity 10 95% (non condensing)
Power supply
External wall power supply 110-240V / 12 V DC, 1.5 A, with energy efficient switching
controler; complies with EuP directive 2008/28/EC
Power consumption
Less than 5 Watt
housing
Metal case, opening for Kensington lock, connectors at back side, prepared for wall mounting
Dimension
Ca. 235 mm x 31.5 mm x 146,5 mm (W x H x D)
Fan
Fanless design therefor high MTBF
Reset button
Restart or reset to factory state possible
Status LEDs
Power, Status, 10 * Ethernet, ADSL, ISDN, WLAN, USB
Certification
Wi-Fi Certified according 802.11abgn (Rel.7.9.4)
Standards and certifications
R&TTE directive 1999/5/EG; EN 55022; EN 55024 + EN 55024/A1; EN61000-3-2; EN
61000-3-3; EN 61000-4-4; EN 60950-1; EN 300 328; EN 301 489-17; EN 301 489-1; EN 301
893
Content of Delivery
Feature
Description
Manual
Quick Installation Guide in German and English
DVD
DVD with system software, management software and documentation
Ethernet cable
1 Ethernet cable, 3m
Power supply
Wall power supply 110-240V / 12 V DC, 1.5 A, with high efficient switching controler
ADSL cable
ADSL cable (RJ11-RJ45), 3m
ISDN (BRI/S0) cable
ISDN (BRI/S0) cable, 3m
WLAN antenna
Three external 3 dBi dipol dualband antennas
Service
Feature
Description
Warranty
2 year manufacturer warranty inclusive 24h advanced replacement
Software Update
Free-of-charge software updates for system software (BOSS) and management software
(DIME manager)
Article number
Feature
Description
bintec RS232bw; art. no. 5510000225 IP Access Router; incl. ADSL modem (Annex B, ISDN); .11n WLAN; 1x ISDN BRI; incl. IPSec
(5 tunnels), certificates, HW encryption; 4+1 Gigabit Eth. switch; USB port; german and intern.
version.
bintec RS232bw - UK; art. no.
5510000261
IP Access Router; incl. ADSL modem (Annex B, ISDN); .11n WLAN; 1x ISDN BRI; incl. IPSec
(5 tunnels), certificates, HW encryption; 4+1 Gigabit Eth. switch; USB port; UK version.
Options
Feature
Description
Cobion Content Filter Small
License for one year Cobion content filter (small); art. no. 80551
IP address ISDN B/D channel license
Free of charge license for IP address transmission in ISDN D or B channel for IPSec
connections; registering under www.funkwerk-ec.com required.
Service package 'small'
Warranty extension of 3 years to a total of 5 years, including advanced replacement for FEC
products of the category "small". (Please find a ) detailed description as well as an overview of
the categories on www.funkwerk-ec.com/servicepackages.
Advanced Replacement
Optional (with costs) advanced replacement outside of warranty time
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RS232bw
09.09.2010
Subject to technical
alterations