GA-770T-USB3
AM3 socket motherboard for
AMD Phenom™ II processor/ AMD Athlon™ II processor
User's Manual
Rev. 1001
12ME-770TB3-1001R
Motherboard
GA-770T-USB3
Jan. 8, 2010
GA-770T-USB3
Motherboard
Jan. 8, 2010
Copyright
© 2009 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or
published in any form or by any means without GIGABYTE's prior written permission.
Documentation Classifications
In order to assist in the use of this product, GIGABYTE provides the following types of documentations:



For quick set-up of the product, read the Quick Installation Guide included with the product.
For detailed product information, carefully read the User's Manual.
For instructions on how to use GIGABYTE's unique features, read or download the information on/from the Support&Downloads\Motherboard\Technology Guide page on our website.
For product-related information, check on our website at:
http://www.gigabyte.com.tw
Identifying Your Motherboard Revision
The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0"
means the revision of the motherboard is 1.0. Check your motherboard revision before updating
motherboard BIOS, drivers, or when looking for technical information.
Example:
Table of Contents
Box Contents....................................................................................................................6
Optional Items..................................................................................................................6
GA-770T-USB3 Motherboard Layout...............................................................................7
GA-770T-USB3 Motherboard Block Diagram...................................................................8
Chapter 1 Hardware Installation......................................................................................9
1-1
1-2
1-3
Installation Precautions..................................................................................... 9
Product Specifications..................................................................................... 10
Installing the CPU and CPU Cooler................................................................ 13
1-3-1
1-3-2
1-4
Installing the Memory...................................................................................... 16
1-4-1
1-4-2
1-5
1-6
1-7
Installing the CPU....................................................................................................13
Installing the CPU Cooler........................................................................................15
Dual Channel Memory Configuration......................................................................16
Installing a Memory ................................................................................................17
Installing an Expansion Card.......................................................................... 18
Back Panel Connectors................................................................................... 19
Internal Connectors......................................................................................... 21
Chapter 2 BIOS Setup...................................................................................................31
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
Startup Screen................................................................................................ 32
The Main Menu............................................................................................... 33
MB Intelligent Tweaker(M.I.T.)......................................................................... 35
Standard CMOS Features............................................................................... 41
Advanced BIOS Features............................................................................... 43
Integrated Peripherals..................................................................................... 45
Power Management Setup.............................................................................. 48
PC Health Status............................................................................................. 50
Load Fail-Safe Defaults................................................................................... 52
2-10
2-11
2-12
2-13
Load Optimized Defaults................................................................................. 52
Set Supervisor/User Password....................................................................... 53
Save & Exit Setup........................................................................................... 54
Exit Without Saving......................................................................................... 54
-4-
Chapter 3 Drivers Installation.........................................................................................55
3-1
3-2
3-3
3-4
3-5
3-6
Installing Chipset Drivers................................................................................ 55
Application Software....................................................................................... 56
Technical Manuals........................................................................................... 56
Contact............................................................................................................ 57
System............................................................................................................ 57
Download Center............................................................................................ 58
Chapter 4 Unique Features............................................................................................59
4-1
4-2
Xpress Recovery2........................................................................................... 59
BIOS Update Utilities...................................................................................... 62
4-2-1
4-2-2
4-3
4-4
4-5
4-6
Updating the BIOS with the Q-Flash Utility..............................................................62
Updating the BIOS with the @BIOS Utility..............................................................65
EasyTune 6..................................................................................................... 66
Easy Energy Saver......................................................................................... 67
Q-Share........................................................................................................... 69
SMART Recovery........................................................................................... 70
Chapter 5 Appendix.......................................................................................................71
5-1
Configuring SATA Hard Drive(s)...................................................................... 71
5-1-1
5-1-2
5-1-3
5-2
Configuring Audio Input and Output................................................................ 83
5-2-1
5-2-2
5-2-3
5-2-4
5-3
Configuring 2/4/5.1/7.1-Channel Audio....................................................................83
Configuring S/PDIF In/Out.......................................................................................85
Configuring Microphone Recording.........................................................................87
Using the Sound Recorder......................................................................................89
Troubleshooting.............................................................................................. 90
5-3-1
5-3-2
5-4
Configuring AMD SB710 SATA Controller ..............................................................71
Making a SATA RAID/AHCI Driver Diskette.............................................................77
Installing the SATA RAID/AHCI Driver and Operating System................................79
Frequently Asked Questions ..................................................................................90
Troubleshooting Procedure.....................................................................................91
Regulatory Statements.................................................................................... 93
-5-
Box Contents
GA-770T-USB3 motherboard
Motherboard driver disk
User's Manual
Quick Installation Guide
One IDE cable
Two SATA 3Gb/s cables
I/O Shield
• The box contents above are for reference only and the actual items shall depend on the product package you obtain. The box contents are subject to change without notice.
• The motherboard image is for reference only.
Optional Items
Floppy disk drive cable (Part No. 12CF1-1FD001-7*R)
2-port USB 2.0 bracket (Part No. 12CR1-1UB030-5*R)
2-port IEEE 1394a bracket (Part No. 12CF1-1IE008-0*R)
2-port SATA power cable (Part No. 12CF1-2SERPW-0*R)
S/PDIF In cable (Part No. 12CR1-1SPDIN-0*R)
COM port cable (Part No. 12CF1-1CM001-3*R)
LPT port cable (Part No. 12CF1-1LP001-0*R)
-6-
GA-770T-USB3 Motherboard Layout
CPU_FAN
SYS_FAN2
KB_MS
RCA_SPDIF
ATX
ATX_12V_2X4
Socket AM3
USB_1394_1
USB_1394_2
R_USB30
AMD 770
PCIEX16
RTL8111D
DDR3_4
PCIEX1_1
DDR3_3
GA-770T-USB3
F_AUDIO
AUDIO
DDR3_1
DDR3_2
USB_LAN
PWR_FAN
NEC
D720200F1
PCIEX1_4
CLR_CMOS
F_USB2
BAT
SPDIF_OUT
PCI1
IDE
AMD SB710
PCIEX1_3
F_USB1
CD_IN
CODEC
SPDIF_IN
PCIEX1_2
M_BIOS
SATA2_1 SATA2_3
B_BIOS
SATA2_0 SATA2_2
SATA2_5
SATA2_4
TSB43AB23
SYS_FAN1
IT8720
PCI2
F_1394
FDD
LPT
-7-
F_PANEL
COMA
GA-770T-USB3 Motherboard Block Diagram
PCIe CLK
(100 MHz)
CPU CLK+/- (200 MHz)
AM3 CPU
1 PCI Express x16
DDR3 1800(O.C.)/1666/1333/1066 MHz
Dual Channel Memory
Hyper Transport 3.0
PCI Express x16
LAN
PCI Express Bus
RJ45
RTL8111D
x1
x1
PCIe CLK (100 MHz)
NEC
D720200F1
x1
PCI Express Bus
x1
x1
AMD 770
2 USB 3.0
x1
PCIe CLK
(100 MHz)
12 USB 2.0/1.1(Note)
4 PCI Express x1
ATA-133/100/66/33 IDE Channel
AMD SB710
Dual BIOS
6 SATA 3Gb/s
PCI Bus
LPC
Bus
TSB43AB23
IT8720
CODEC
3 IEEE 1394a
PCI CLK
(33 MHz)
(Note)
LPT Port
COM Port
Two share the same ports with USB 3.0.
-8-
S/PDIF In
S/ PDIF Out
PS/2 KB/Mouse
Surround Speaker Out
Center/Subwoofer Speaker Out
Side Speaker Out
MIC
Line Out
Line In
2 PCI
Floppy
Chapter 1 Hardware Installation
1-1
Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can
become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read
the user's manual and follow these procedures:
• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
• Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
• When connecting hardware components to the internal connectors on the motherboard,
make sure they are connected tightly and securely.
• When handling the motherboard, avoid touching any metal leads or connectors.
• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,
keep your hands dry and first touch a metal object to eliminate static electricity.
• Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
• Before unplugging the power supply cable from the motherboard, make sure the power supply has been turned off.
• Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
• Before using the product, please verify that all cables and power connectors of your hardware components are connected.
• To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
• Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
• Do not place the computer system on an uneven surface.
• Do not place the computer system in a high-temperature environment.
• Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user.
• If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certified computer technician.
-9-
Hardware Installation
1-2 Product Specifications
CPU
 Support for AM3 processors:
AMD Phenom™ II processor/ AMD Athlon™ II processor
(Go to GIGABYTE's website for the latest CPU support list.)
Hyper Transport Bus 5200 MT/s
Chipset  North Bridge: AMD 770
 South Bridge: AMD SB710
 4 x 1.5V DDR3 DIMM sockets supporting up to 16 GB of system memory (Note 1)
Memory
 Dual channel memory architecture
 Support for DDR3 1800 (O.C.)/1666/1333/1066 MHz memory modules
(Go to GIGABYTE's website for the latest memory support list.)
(Note 2)
 Support for ECC memory modules
Audio  Realtek ALC888 codec
 High Definition Audio
 2/4/5.1/7.1-channel
 Support for S/PDIF In/Out
 Support for CD In
LAN
 1 x Realtek RTL8111D chips (10/100/1000 Mbit)
Expansion Slots  1 x PCI Express x16 slot, running at x16
(The PCI Express x16 slot conforms to PCI Express 2.0 standard.)
4
x PCI Express x1 slots

 2 x PCI slots
Storage Interface  South Bridge:
- 1 x IDE connector supporting ATA-133/100/66/33 and up to 2 IDE devices
- 6 x SATA 3Gb/s connectors (SATA2_0, SATA2_1, SATA2_2, SATA2_3, SATA2_4, SATA2_5) supporting up to 6 SATA 3Gb/s devices
- Support for SATA RAID 0, RAID 1, RAID 10, and JBOD
 iTE IT8720 chip:
- 1 x floppy disk drive connector supporting up to 1 floppy disk drive
 South Bridge:
USB - Up to 12 USB 2.0/1.1 ports (Note 3) (8 on the back panel, 4 via the USB
brackets connected to the internal USB headers)
 NEC D720200F1 chip
- Up to 2 USB 3.0 ports on the back panel
Hardware Installation
- 10 -
IEEE 1394
 T.I. TSB43AB23 chip:
- Up to 3 IEEE 1394a ports (2 on the back panel, 1 via the IEEE 1394a bracket connected to the internal IEEE 1394a header)
w 1 x 24-pin ATX main power connector
Internal
Connectors
w 1 x 8-pin ATX 12V power connector
w 1 x floppy disk drive connector
w 1 x IDE connector
w 6 x SATA 3Gb/s connectors
w 1 x CPU fan header
w 2 x system fan headers
w 1 x power fan header
w 1 x front panel header
w 1 x front panel audio header
w 1 x CD In connector
w 1 x S/PDIF In header
w 1 x S/PDIF Out header
w 2 x USB 2.0/1.1 headers
w 1 x IEEE 1394a header
w 1 x serial port header
w 1 x parallel port header
w 1 x clearing CMOS jumper
w 1 x PS/2 keyboard port
Back Panel Connectors
w 1 x PS/2 mouse port
w 1 x coaxial S/PDIF Out connector
w 1 x optical S/PDIF Out connector
w 6 x USB 2.0/1.1 ports
w 2 x USB 3.0/2.0 ports
w 2 x IEEE 1394a ports
w 1 x RJ-45 port
w 6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker Out/
Side Speaker Out/Line In/Line Out/Microphone)
I/O Controller
w iTE IT8720 chip
Hardware Monitor w
w
w
w
w
w
System voltage detection
CPU/System temperature detection
CPU/system/power fan speed detection
CPU overheating warning
CPU/system/power fan fail warning
CPU/System fan speed control (Note 4)
- 11 -
Hardware Installation
BIOS
Unique Features
w
w
w
w
w
w
w
w
w
w
w
w
w
w
2 x 8 Mbit flash
Use of licensed AWARD BIOS
Support for DualBIOS™
PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b
Support for @BIOS
Support for Q-Flash
Support for Xpress BIOS Rescue
Support for Download Center
Support for Xpress Install
Support for Xpress Recovery2
Support for EasyTune (Note 5)
Support for Easy Energy Saver
Support for Smart Recovery
Support for Q-Share
Bundled Software w Norton Internet Security (OEM version)
Operating Systemw Support for Microsoft® Windows® 7/Vista/XP
Form Factor
w ATX Form Factor; 30.5cm x 22.0cm
(Note 1) Due to Windows 32-bit operating system limitation, when more than 4 GB of physical memory is
installed, the actual memory size displayed will be less than 4 GB.
(Note 2) Use of a CPU that supports ECC is required if you wish to install ECC memory.
(Note 3) Two share the same ports with USB 3.0.
(Note 4) Whether the CPU/system fan speed control function is supported will depend on the CPU/system
cooler you install.
(Note 5) Available functions in EasyTune may differ by motherboard model.
Hardware Installation
- 12 -
1-3 Installing the CPU and CPU Cooler
Read the following guidelines before you begin to install the CPU:
• Make sure that the motherboard supports the CPU.
(Go to GIGABYTE's website for the latest CPU support list.)
• Always turn off the computer and unplug the power cord from the power outlet before installing
the CPU to prevent hardware damage.
• Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may
locate the notches on both sides of the CPU and alignment keys on the CPU socket.)
• Apply an even and thin layer of thermal grease on the surface of the CPU.
• Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage of the CPU may occur.
• Set the CPU host frequency in accordance with the CPU specifications. It is not recommended
that the system bus frequency be set beyond hardware specifications since it does not meet the
standard requirements for the peripherals. If you wish to set the frequency beyond the standard
specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc.
1-3-1 Installing the CPU
A. Locate the pin one (denoted by a small triangle) of the CPU socket and the CPU.
A Small Triangle Mark
Denotes Pin One of the
Socket
A Small Triangle Marking
Denotes CPU Pin One
- 13 -
AM3 Socket
AM3 CPU
Hardware Installation
B. Follow the steps below to correctly install the CPU into the motherboard CPU socket.
• Before installing the CPU, make sure to turn off the computer and unplug the power cord from the
power outlet to prevent damage to the CPU.
• Do not force the CPU into the CPU socket. The CPU cannot fit in if oriented incorrectly. Adjust the
CPU orientation if this occurs.
CPU Socket
Locking Lever
Step 1:
Completely lift up the CPU socket locking lever.
Step 2:
Align the CPU pin one (small triangle marking) with the triangle mark
on the CPU socket and gently insert the CPU into the socket. Make
sure that the CPU pins fit perfectly into their holes. Once the CPU is
positioned into its socket, place one finger down on the middle of the
CPU, lowering the locking lever and latching it into the fully locked
position.
Hardware Installation
- 14 -
1-3-2 Installing the CPU Cooler
Follow the steps below to correctly install the CPU cooler on the CPU. (The following procedure uses the
GIGABYTE cooler as the example.)
Step 1:
Apply an even and thin layer of thermal grease
on the surface of the installed CPU.
Step 2:
Place the CPU cooler on the CPU.
Step 3:
Hook the CPU cooler clip to the mounting lug
on one side of the retention frame. On the other
side,push straight down on the the CPU cooler
clip to hook it to the mounting lug on the retention frame.
Step 4:
Turn the cam handle from the left side to the
right side (as the picture above shows) to lock
into place. (Refer to your CPU cooler installation
manual for instructions on installing the cooler.)
Step 5:
Finally, attach the power connector of the CPU cooler to the CPU
fan header (CPU_FAN) on the motherboard.
Use extreme care when removing the CPU cooler because the thermal grease/tape between the
CPU cooler and CPU may adhere to the CPU. Inadequately removing the CPU cooler may damage
the CPU.
- 15 -
Hardware Installation
1-4 Installing the Memory
Read the following guidelines before you begin to install the memory:
• Make sure that the motherboard supports the memory. It is recommended that memory of the
same capacity, brand, speed, and chips be used.
(Go to GIGABYTE's website for the latest memory support list.)
• Always turn off the computer and unplug the power cord from the power outlet before installing
the memory to prevent hardware damage.
• Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.
1-4-1 Dual Channel Memory Configuration
This motherboard provides four DDR3 memory sockets and supports Dual Channel Technology. After the
memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual Channel memory mode will double the original memory bandwidth.
The four DDR3 memory sockets are divided into two channels and each channel has two memory sockets as
following:
Channel 0: DDR3_1, DDR3_3
Channel 1: DDR3_2, DDR3_4
Dual Channel Memory Configurations Table
DDR3_1 DDR3_2 DDR3_3 DDR3_4
Two Modules
Four Modules
DS/SS
DS/SS
- -
--
- -
- -
DS/SS
DS/SS
DS/SS
DS/SS
DS/SS
DS/SS
(SS=Single-Sided, DS=Double-Sided, "- -"=No Memory)
DDR3_1
DDR3_2
DDR3_3
DDR3_4
If two memory modules are to be installed, it is recommended that you install them in the DDR3_1 and
DDR3_2 sockets.
Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.
1. Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.
2. When enabling Dual Channel mode with two or four memory modules, it is recommended that
memory of the same capacity, brand, speed, and chips be used and installed in the same colored
DDR3 sockets for optimum performance.
Hardware Installation
- 16 -
1-4-2 Installing a Memory
Before installing a memory module, make sure to turn off the computer and unplug the power
cord from the power outlet to prevent damage to the memory module.
DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs. Be sure to install
DDR3 DIMMs on this motherboard.
Notch
DDR3 DIMM
A DDR3 memory module has a notch, so it can only fit in one direction. Follow the steps below to correctly
install your memory modules in the memory sockets.
Step 1:
Note the orientation of the memory module. Spread the retaining
clips at both ends of the memory socket. Place the memory module
on the socket. As indicated in the picture on the left, place your fingers on the top edge of the memory, push down on the memory and
insert it vertically into the memory socket.
Step 2:
The clips at both ends of the socket will snap into place when the
memory module is securely inserted.
- 17 -
Hardware Installation
1-5 Installing an Expansion Card
Read the following guidelines before you begin to install an expansion card:
• Make sure the motherboard supports the expansion card. Carefully read the manual that came
with your expansion card.
• Always turn off the computer and unplug the power cord from the power outlet before installing
an expansion card to prevent hardware damage.
PCI Express x1 Slot
PCI Express x16 Slot
PCI Slot
Follow the steps below to correctly install your expansion card in the expansion slot.
1. Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel.
2. Align the card with the slot, and press down on the card until it is fully seated in the slot.
3. Make sure the metal contacts on the card are completely inserted into the slot.
4. Secure the card’s metal bracket to the chassis back panel with a screw.
5. After installing all expansion cards, replace the chassis cover(s).
6. Turn on your computer. If necessary, go to BIOS Setup to make any required BIOS changes for your
expansion card(s).
7. Install the driver provided with the expansion card in your operating system.
Example: Installing and Removing a PCI Express Graphics Card:
• Installing a Graphics Card:
Gently push down on the top edge of the card until
it is fully inserted into the PCI Express slot. Make
sure the card is securely seated in the slot and
does not rock.
• Removing the Card:
Gently push back on the lever on the slot and then lift the card straight out from
the slot.
Hardware Installation
- 18 -
1-6 Back Panel Connectors
PS/2 Mouse Port
Use this port to connect a PS/2 mouse.
PS/2 Keyboard Port
Use this port to connect a PS/2 keyboard.
Optical S/PDIF Out Connector
This connector provides digital audio out to an external audio system that supports digital optical audio.
Before using this feature, ensure that your audio system provides an optical digital audio in connector.
Coaxial S/PDIF Out Connector
This connector provides digital audio out to an external audio system that supports digital coaxial audio.
Before using this feature, ensure that your audio system provides a coaxial digital audio in connector.
IEEE 1394a Port
The IEEE 1394 port supports the IEEE 1394a specification, featuring high speed, high bandwidth and
hotplug capabilities. Use this port for an IEEE 1394a device.
USB 2.0/1.1 Port
The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.
USB 3.0/2.0 Port
The USB 3.0 port supports the USB 3.0 specification and is compatible to the USB 2.0/1.1 specification.
Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.
Connection/
Speed LED
Activity LED
LAN Port
Connection/Speed LED:
State Orange Green Off
Activity LED:
Description
1 Gbps data rate
100 Mbps data rate
10 Mbps data rate
State Blinking
Off
Description
Data transmission or receiving is occurring
No data transmission or receiving is occurring
• When removing the cable connected to a back panel connector, first remove the cable from your
device and then remove it from the motherboard.
• When removing the cable, pull it straight out from the connector. Do not rock it side to side to
prevent an electrical short inside the cable connector.
- 19 -
Hardware Installation
Center/Subwoofer Speaker Out Jack (Orange)
Use this audio jack to connect center/subwoofer speakers in a 5.1/7.1-channel audio configuration.
Rear Speaker Out Jack (Black)
Use this audio jack to connect rear speakers in a 4/5.1/7.1-channel audio configuration.
Side Speaker Out Jack (Gray)
Use this audio jack to connect side speakers in a 7.1-channel audio configuration.
Line In Jack (Blue)
The default line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out Jack (Green)
The default line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be
used to connect front speakers in a 4/5.1/7.1-channel audio configuration.
Mic In Jack (Pink)
The default Mic in jack. Microphones must be connected to this jack.
In addition to the default speakers settings, the
~
audio jacks can be reconfigured to per-
form different functions via the audio software. Only microphones still MUST be connected to
the default Mic in jack ( ). Refer to the instructions on setting up a 2/4/5.1/7.1-channel audio
configuration in Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio."
Hardware Installation
- 20 -
1-7 Internal Connectors
4
1
3
2
5
10
8
7
11
13
12
8
16
4
19
15
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
ATX_12V_2X4
ATX
CPU_FAN
SYS_FAN1/2
PWR_FAN
FDD
IDE
SATA2_0/1/2/3/4/5
F_PANEL
F_AUDIO
17
18
6
11)
12)
13)
14)
15)
16)
17)
18)
19)
14
9
CD_IN
SPDIF_IN
SPDIF_OUT
F_USB1/F_USB2
F_1394
COMA
LPT
BAT
CLR_CMOS
Read the following guidelines before connecting external devices:
• First make sure your devices are compliant with the connectors you wish to connect.
• Before installing the devices, be sure to turn off the devices and your computer. Unplug the
power cord from the power outlet to prevent damage to the devices.
• After installing the device and before turning on the computer, make sure the device cable has
been securely attached to the connector on the motherboard.
- 21 -
Hardware Installation
1/2)ATX_12V_2X4/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, first make sure the power supply
is turned off and all devices are properly installed. The power connector possesses a foolproof design.
Connect the power supply cable to the power connector in the correct orientation. The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will
not start.
To meet expansion requirements, it is recommended that a power supply that can withstand high
power consumption be used (500W or greater). If a power supply is used that does not provide
the required power, the result can lead to an unstable or unbootable system.
4
1
8
5
ATX_12V_2X4
ATX_12V_2X4:
Pin No.
1
2
3
4
5
6
7
8
Definition
GND (Only for 2x4-pin 12V)
GND (Only for 2x4-pin 12V)
GND
GND
+12V (Only for 2x4-pin 12V)
+12V (Only for 2x4-pin 12V)
+12V
+12V
ATX:
12
24
1
13
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
Definition
3.3V
3.3V
GND
+5V
GND
+5V
GND
Power Good
5VSB (stand by +5V)
+12V
+12V (Only for 2x12-pin ATX)
3.3V (Only for 2x12-pin ATX)
ATX
Hardware Installation
- 22 -
Pin No. Definition
13
3.3V
14 -12V
15
16
17
18
19
20
21
22
23
24
GND
PS_ON (soft On/Off)
GND
GND
GND
-5V
+5V
+5V
+5V (Only for 2x12-pin ATX)
GND (Only for 2x12-pin ATX)
3/4/5) CPU_FAN/SYS_FAN1/SYS_FAN2/PWR_FAN (Fan Headers)
The motherboard has a 4-pin CPU fan header (CPU_FAN), a 4-pin (SYS_FAN1) and one 3-pin (SYS_
FAN2) system fan headers, and a 3-pin power fan header (PWR_FAN). Most fan headers possess a
foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation
(the black connector wire is the ground wire). The motherboard supports CPU fan speed control, which
requires the use of a CPU fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.
CPU_FAN:
1
CPU_FAN
Pin No.
1
2
3
4
Definition
GND
+12V / Speed Control
Sense
Speed Control
SYS_FAN1:
1
SYS_FAN1
Pin No.
1
2
3
4
Definition
GND
+12V / Speed Control
Sense
Reserve
SYS_FAN2/PWR_FAN:
1
SYS_FAN2
1
PWR_FAN
Pin No.
1
2
3
Definition
GND
+12V
Sense
• Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang.
• These fan headers are not configuration jumper blocks. Do not place a jumper cap on the
headers.
6) FDD (Floppy Disk Drive Connector)
This connector is used to connect a floppy disk drive. The types of floppy disk drives supported are:
360 KB, 720 KB, 1.2 MB, 1.44 MB, and 2.88 MB. Before connecting a floppy disk drive, be sure to locate
pin 1 of the connector and the floppy disk drive cable. The pin 1 of the cable is typically designated by a
stripe of different color. For purchasing the optional floppy disk drive cable, please contact the local dealer.
33
1
34
2
- 23 -
Hardware Installation
7) IDE (IDE Connector)
The IDE connector supports up to two IDE devices such as hard drives and optical drives. Before attaching the IDE cable, locate the foolproof groove on the connector. If you wish to connect two IDE devices,
remember to set the jumpers and the cabling according to the role of the IDE devices (for example,
master or slave). (For information about configuring master/slave settings for the IDE devices, read the
instructions from the device manufacturers.)
39
40
2
1
8) SATA2_0/1/2/3/4/5 (SATA 3Gb/s Connectors, Controlled by AMD SB710 South Bridge)
The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard.
Each SATA connector supports a single SATA device. The AMD SB710 controller supports RAID 0,
RAID 1, RAID 10 and JBOD. Refer to Chapter 5, "Configuring SATA Hard Drive(s)," for instructions on
configuring a RAID array.
1
7
SATA2_1
SATA2_3
SATA2_0
SATA2_2
1
7
SATA2_5
7
1
1
7
Pin No.
1
2
3
4
5
6
7
Definition
GND
TXP
TXN
GND
RXN
RXP
GND
SATA2_4
Please connect the L-shaped end of
the SATA 3Gb/s cable to your SATA
hard drive.
• A RAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard
drives are to be used, the total number of hard drives must be an even number.
• A RAID 10 configuration requires at least four hard drives and the total number of hard drives
must be an even number.
Hardware Installation
- 24 -
9) F_PANEL (Front Panel Header)
Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status
indicator on the chassis to this header according to the pin assignments below. Note the positive and
negative pins before connecting the cables.
Power
Switch
SPEAK-
Speaker
SPEAK+
MSG+
MSGPW+
PW-
Message/Power/
Sleep LED
Hard Drive
Activity LED
Reset
Switch
PWR-
20
19
PWR+
2
1
HD+
HDRESRES+
CICI+
Power LED
Chassis Intrusion
Header
• MSG/PWR (Message/Power/Sleep LED, Yellow/Purple):
System Status LED Connects to the power status indicator on the chassis front panel. The LED
is on when the system is operating. The LED keeps blinking when the sysS0
On
S1
Blinking tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep
S3/S4/S5
Off
state or powered off (S5).
• PW (Power Switch, Red):
Connects to the power switch on the chassis front panel. You may configure the way to turn off your
system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management Setup," for
more information).
• SPEAK (Speaker, Orange):
Connects to the speaker on the chassis front panel. The system reports system startup status by issuing a beep code. One single short beep will be heard if no problem is detected at system startup. If
a problem is detected, the BIOS may issue beeps in different patterns to indicate the problem. Refer
to Chapter 5, "Troubleshooting," for information about beep codes.
• HD (Hard Drive Activity LED, Blue)
Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive
is reading or writing data.
• RES (Reset Switch, Green):
Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer
if the computer freezes and fails to perform a normal restart.
• CI (Chassis Intrusion Header, Gray):
Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover
has been removed. This function requires a chassis with a chassis intrusion switch/sensor.
The front panel design may differ by chassis. A front panel module mainly consists of power
switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your
chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.
- 25 -
Hardware Installation
10) F_AUDIO (Front Panel Audio Header)
The front panel audio header supports Intel High Definition audio (HD) and AC'97 audio. You may connect
your chassis front panel audio module to this header. Make sure the wire assignments of the module connector match the pin assignments of the motherboard header. Incorrect connection between the module
connector and the motherboard header will make the device unable to work or even damage it.
10
9
2
1
For HD Front Panel Audio:
Pin No. Definition
1
MIC2_L
2
GND
3
MIC2_R
4
-ACZ_DET
5
LINE2_R
6
GND
7
FAUDIO_JD
8
No Pin
9
LINE2_L
10
GND
For AC'97 Front Panel Audio:
Pin No. Definition
1
MIC
2
GND
3
MIC Power
4
NC
5
Line Out (R)
6
NC
7
NC
8
No Pin
9
Line Out (L)
10
NC
• The front panel audio header supports HD audio by default. If your chassis provides an AC'97
front panel audio module, refer to the instructions on how to activate AC'97 functionality via
the audio software in Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio."
• Audio signals will be present on both of the front and back panel audio connections simultaneously. If you want to mute the back panel audio (only supported when using an HD front panel
audio module), refer to Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio."
• Some chassis provide a front panel audio module that has separated connectors on each wire
instead of a single plug. For information about connecting the front panel audio module that
has different wire assignments, please contact the chassis manufacturer.
11) CD_IN (CD In Connector)
You may connect the audio cable that came with your optical drive to the header.
1
Hardware Installation
- 26 -
Pin No.
1
2
3
4
Definition
CD-L
GND
GND
CD-R
12) SPDIF_IN (S/PDIF In Header)
This header supports digital S/PDIF In and can connect to an audio device that supports digital audio out
via an optional S/PDIF In cable. For purchasing the optional S/PDIF In cable, please contact the local
dealer.
1
Pin No.
1
2
3
Definition
Power
SPDIFI
GND
13) SPDIF_OUT (S/PDIF Out Header)
This header supports digital S/PDIF Out and connects a S/PDIF digital audio cable (provided by expansion cards) for digital audio output from your motherboard to certain expansion cards like graphics cards
and sound cards. For example, some graphics cards may require you to use a S/PDIF digital audio cable
for digital audio output from your motherboard to your graphics card if you wish to connect an HDMI
display to the graphics card and have digital audio output from the HDMI display at the same time. For
information about connecting the S/PDIF digital audio cable, carefully read the manual for your expansion card.
1
- 27 -
Pin No. Definition
1
SPDIFO
2
GND
Hardware Installation
14) F_USB1/F_USB2 (USB Headers)
The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an
optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.
10
9
2
1
Pin No.
1
2
3
G.QBOFM
4
5
6
7
8
9
10
Definition
Power (5V)
Power (5V)
USB DXUSB DYUSB DX+
USB DY+
GND
GND
No Pin
NC
• Do not plug the IEEE 1394 bracket (2x5-pin) cable into the USB header.
• Prior to installing the USB bracket, be sure to turn off your computer and unplug the power
cord from the power outlet to prevent damage to the USB bracket.
15) F_1394 (IEEE 1394a Header)
The header conforms to IEEE 1394a specification. The IEEE 1394a header can provide one IEEE 1394a
port via an optional IEEE 1394a bracket. For purchasing the optional IEEE 1394a bracket, please contact the local dealer.
9
10
1
2
Pin No.
1
2
3
4
5
6
7
8
9
10
Definition
TPA+
TPAGND
GND
TPB+
TPBPower (12V)
Power (12V)
No Pin
GND
• Do not plug the USB bracket cable into the IEEE 1394a header.
• Prior to installing the IEEE 1394a bracket, be sure to turn off your computer and unplug the
power cord from the power outlet to prevent damage to the IEEE 1394a bracket.
• To connect an IEEE 1394a device, attach one end of the device cable to your computer and
then attach the other end of the cable to the IEEE 1394a device. Ensure that the cable is securely connected.
Hardware Installation
- 28 -
16) COMA (Serial Port Header)
The COM header can provide one serial port via an optional COM port cable. For purchasing the optional COM port cable, please contact the local dealer.
10
9
2
1
Pin No.
1
2
3
4
5
6
7
8
9
10
Definition
NDCDNSIN
NSOUT
NDTRGND
NDSRNRTSNCTSNRINo Pin
17) LPT (Parallel Port Header)
The LPT header can provide one parallel port via an optional LPT port cable. For purchasing the optional
LPT port cable, please contact the local dealer.
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
- 29 -
25
1
24
2
Definition
STBAFDPD0
ERRPD1
INITPD2
SLINPD3
GND
PD4
GND
PD5
Pin No.
14
15
16
17
18
19
20
21
22
23
24
25
26
Definition
GND
PD6
GND
PD7
GND
ACKGND
BUSY
GND
PE
No Pin
SLCT
GND
Hardware Installation
18) BAT (Battery)
The battery provides power to keep the values (such as BIOS configurations, date, and time information)
in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a
low level, or the CMOS values may not be accurate or may be lost.
You may clear the CMOS values by removing the battery:
1. Turn off your computer and unplug the power cord.
2. Gently remove the battery from the battery holder and wait for one
minute. (Or use a metal object like a screwdriver to touch the positive
and negative terminals of the battery holder, making them short for 5
seconds.)
3. Replace the battery.
4. Plug in the power cord and restart your computer.
• Always turn off your computer and unplug the power cord before replacing the battery.
• Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with
an incorrect model.
• Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain about the battery model.
• When installing the battery, note the orientation of the positive side (+) and the negative side (-)
of the battery (the positive side should face up).
• Used batteries must be handled in accordance with local environmental regulations.
19) CLR_CMOS (Clearing CMOS Jumper)
Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and reset the
CMOS values to factory defaults. To clear the CMOS values, place a jumper cap on the two pins to temporarily short the two pins or use a metal object like a screwdriver to touch the two pins for a few seconds.
Open: Normal
Short: Clear CMOS Values
• Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values.
• After clearing the CMOS values and before turning on your computer, be sure to remove the
jumper cap from the jumper. Failure to do so may cause damage to the motherboard.
• After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or manually configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS
configurations).
Hardware Installation
- 30 -
Chapter 2 BIOS Setup
BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the
motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup,
saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that
allows the user to modify basic system configuration settings or to activate certain system features. When
the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to keep
the configuration values in the CMOS.
To access the BIOS Setup program, press the <Delete> key during the POST when the power is turned on.
To see more advanced BIOS Setup menu options, you can press <Ctrl> + <F1> in the main menu of the
BIOS Setup program.
To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility.
• Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating
system.
• @BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the
Internet and updates the BIOS.
For instructions on using the Q-Flash and @BIOS utilities, refer to Chapter 4, "BIOS Update Utilities."
• Because BIOS flashing is potentially risky, if you do not encounter problems using the current
version of BIOS, it is recommended that you not flash the BIOS. To flash the BIOS, do it with
caution. Inadequate BIOS flashing may result in system malfunction.
• BIOS will emit a beep code during the POST. Refer to Chapter 5, "Troubleshooting," for the beep
codes description.
• It is recommended that you not alter the default settings (unless you need to) to prevent system
instability or other unexpected results. Inadequately altering the settings may result in system's
failure to boot. If this occurs, try to clear the CMOS values and reset the board to default values.
(Refer to the "Load Optimized Defaults" section in this chapter or introductions of the battery/
clearing CMOS jumper in Chapter 1 for how to clear the CMOS values.)
- 31 -
BIOS Setup
2-1 Startup Screen
The following screens may appear when the computer boots.
A. The LOGO Screen (Default)
Function Keys
B. The POST Screen
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2009, Award Software, Inc.
Motherboard Model
BIOS Version
AMD 770 BIOS for GA-770T-USB3 E7
.
.
.
.
<DEL>: BIOS Setup <F9>: XpressRecovery2 <F12>: Boot Menu <End>: Qflash
12/14/2009-RX780-SB710-7A66AG0WC-00
Function Keys
Function Keys:
<TAB>: POST SCREEN
Press the <Tab> key to show the BIOS POST screen. To show the BIOS POST screen at system startup, refer to the instructions on the Full Screen LOGO Show item on page 44.
<DEL>: BIOS SETUP\Q-FLASH
Press the <Delete> key to enter BIOS Setup or to access the Q-Flash utility in BIOS Setup.
<F9>: XPRESS RECOVERY2
If you have ever entered Xpress Recovery2 to back up hard drive data using the driver disk, the <F9>
key can be used for subsequent access to Xpress Recovery2 during the POST. For more information,
refer to Chapter 4, "Xpress Recovery2."
<F12>: BOOT MENU
Boot Menu allows you to set the first boot device without entering BIOS Setup. In Boot Menu, use the up
arrow key <h> or the down arrow key <i> to select the first boot device, then press <Enter> to accept.
To exit Boot Menu, press <Esc>. The system will directly boot from the device configured in Boot Menu.
Note: The setting in Boot Menu is effective for one time only. After system restart, the device boot order
will still be based on BIOS Setup settings. You can access Boot Menu again to change the first boot device setting as needed.
<END>: Q-FLASH
Press the <End> key to access the Q-Flash utility directly without having to enter BIOS Setup first.
BIOS Setup
- 32 -
2-2 The Main Menu
Once you enter the BIOS Setup program, the Main Menu (as shown below) appears on the screen. Use arrow keys to move among the items and press <Enter> to accept or enter a sub-menu.
(Sample BIOS Version: E7)
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software






MB Intelligent Tweaker(M.I.T.)
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PC Health Status
ESC: Quit F8: Q-Flash
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
: Select Item
F10: Save & Exit Setup
F11: Save CMOS to BIOS
F12: Load CMOS from BIOS
Change CPU's Clock & Voltage
BIOS Setup Program Function Keys
<h><i><f><g>Move the selection bar to select an item
<Enter>
Execute command or enter the submenu
<Esc>
Main Menu: Exit the BIOS Setup program
Submenus: Exit current submenu
<Page Up>
Increase the numeric value or make changes
<Page Down>
Decrease the numeric value or make changes
<F1>
Show descriptions of the function keys
<F2>
Move cursor to the Item Help block on the right (submenus only)
<F5>
Restore the previous BIOS settings for the current submenus
<F6>
Load the Fail-Safe BIOS default settings for the current submenus
<F7>
Load the Optimized BIOS default settings for the current submenus
<F8>
Access the Q-Flash utility
<F9>
Display system information
<F10>
Save all the changes and exit the BIOS Setup program
<F11>
Save CMOS to BIOS
<F12>
Load CMOS from BIOS
Main Menu Help
The on-screen description of a highlighted setup option is displayed on the bottom line of the Main Menu.
Submenu Help
While in a submenu, press <F1> to display a help screen (General Help) of function keys available for the
menu. Press <Esc> to exit the help screen. Help for each item is in the Item Help block on the right side of
the submenu.
• If you do not find the settings you want in the Main Menu or a submenu, press <Ctrl>+<F1> to
access more advanced options.
• When the system is not stable as usual, select the Load Optimized Defaults item to set your
system to its defaults.
• The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS
version.
- 33 -
BIOS Setup
 The Functions of the <F11> and <F12> keys (For the Main Menu Only)
 F11: Save CMOS to BIOS
This function allows you to save the current BIOS settings to a profile. You can create up to 8 profiles
(Profile 1-8) and name each profile. First enter the profile name (to erase the default profile name, use
the SPACE key) and then press <Enter> to complete.
 F12: Load CMOS from BIOS
If your system becomes unstable and you have loaded the BIOS default settings, you can use this
function to load the BIOS settings from a profile created before, without the hassles of reconfiguring the
BIOS settings. First select the profile you wish to load, then press <Enter> to complete.
 MB Intelligent Tweaker(M.I.T.)
Use this menu to configure the clock, frequency and voltages of your CPU, memory, etc.
 Standard CMOS Features
Use this menu to configure the system time and date, hard drive types, floppy disk drive types, and the
type of errors that stop the system boot, etc.
 Advanced BIOS Features
Use this menu to configure the device boot order, advanced features available on the CPU, and the primary display adapter.
 Integrated Peripherals
Use this menu to configure all peripheral devices, such as IDE, SATA, USB, integrated audio, and integrated LAN, etc.
 Power Management Setup
Use this menu to configure all the power-saving functions.
Use this menu to see information about autodetected system/CPU temperature, system voltage and fan
speed, etc.
 PC Health Status
 Load Fail-Safe Defaults
Fail-Safe defaults are factory settings for the most stable, minimal-performance system operations.
Optimized defaults are factory settings for optimal-performance system operations.
Change, set, or disable password. It allows you to restrict access to the system and BIOS Setup.
A supervisor password allows you to make changes in BIOS Setup.
Change, set, or disable password. It allows you to restrict access to the system and BIOS Setup.
A user password only allows you to view the BIOS settings but not to make changes.
Save all the changes made in the BIOS Setup program to the CMOS and exit BIOS Setup. (Pressing
<F10> can also carry out this task.)
 Load Optimized Defaults
 Set Supervisor Password
 Set User Password
 Save & Exit Setup
 Exit Without Saving
Abandon all changes and the previous settings remain in effect. Pressing <Y> to the confirmation message will exit BIOS Setup. (Pressing <Esc> can also carry out this task.)
BIOS Setup
- 34 -
2-3 MB Intelligent Tweaker(M.I.T.)
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
MB Intelligent Tweaker(M.I.T.)
} Advanced Clock Calibration
CPU Clock Ratio
CPU NorthBridge Freq. CPU Host Clock Control
x CPU Frequency(MHz)
PCIE Clock(MHz)
HT Link Frequency
Set Memory Clock
x Memory Clock
} DRAM Configuration ******** System Voltage Optimized ********
System Voltage Control
x DRAM Voltage Control
x DDR VTT Voltage Control
x NB Voltage Control
x SB/HT Voltage Control
x NB PCIE Voltage Control
x CPU NB VID Control
x CPU Voltage Control
Enter: Select
: Move
F5: Previous Values
Item Help
Menu Level 
[Press Enter]
[Auto]
2800Mhz
[Auto]
2000Mhz
[Auto]
200
[Auto]
[Auto]
[Auto]
x6.66
1333Mhz
[Press Enter]
[Auto]
Auto
Auto
Auto
Auto
Auto
Auto
Auto
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
MB Intelligent Tweaker(M.I.T.)
Normal CPU Vcore
Enter: Select
: Move
F5: Previous Values
1.3250V
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
Item Help
Menu Level 
ESC: Exit
F1: General Help
F7: Optimized Defaults
• Whether the system will work stably with the overclock/overvoltage settings you made is dependent on your overall system configurations. Incorrectly doing overclock/overvoltage may result in
damage to CPU, chipset, or memory and reduce the useful life of these components. This page is
for advanced users only and we recommend you not to alter the default settings to prevent system
instability or other unexpected results. (Inadequately altering the settings may result in system's
failure to boot. If this occurs, clear the CMOS values and reset the board to default values.)
• When the System Voltage Optimized item blinks in red, it is recommended that you set the
System Voltage Control item to Auto to optimize the system voltage settings.
- 35 -
BIOS Setup
Advanced Clock Calibration
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
Advanced Clock Calibration
x
x
x
x
x
x
x
EC Firmware Selection
Advanced Clock Calibration
Value (All Cores)
Value (Core 0)
Value (Core 1)
Value (Core 2)
Value (Core 3)
CPU core Control
CPU core 2(Note)
CPU core 3 (Note)
Enter: Select
: Move
F5: Previous Values
Item Help
Menu Level 
[Normal]
[Disabled]
-2%
-2%
-2%
-2%
-2%
[Auto]
Enabled
Enabled
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
EC Firmware Selection
Allows you to select the EC firmware version when Advanced Clock Calibration is enabled. After the
selection, select Save & Exit Setup in the BIOS Main Menu and then press <Y>. A message which says
"BIOS Is Updating EC Firmware!!! Don't Turn Off Or Reset System" will appear. Wait for a few seconds
and the system will automatically restart for the settings to take effect.
Normal
Uses the standard AMD EC firmware version. (Default)
Hybrid
Uses the specific AMD EC firmware version.
Advanced Clock Calibration
Allows you to determine whether to enable Advanced Clock Calibration when using an AMD Black Edition CPU.
Disabled
Disables this function. (Default)
Auto
Lets the BIOS to configure the settings to defaults.
All Cores
Configures Advanced Clock Calibration for all CPU cores.
Per Core
Individually configures Advanced Clock Calibration for each CPU core.
Value (All Cores)
This option is configurable only when Advanced Clock Calibration is set to All Cores.
Options are: -12%~+12%.
Value (Core 0), Value (Core 1), Value (Core 2), Value (Core 3)
This option is configurable only when Advanced Clock Calibration is set to All Cores.
Options are: -12%~+12%.
CPU core Control
Allows you to determine whether to manually enable/disable CPU Core 2 and Core 3. Manual allows the
two items below to be configurable. Options are: Auto (default), Manual.
Auto
Lets the BIOS to enable all CPU cores (number of cores available depends on the CPU being used).
Manual
Allows you to individually enable/disable CPU Core 2 and Core 3.
(Note)
This item is present only if you install a CPU that supports this feature.
BIOS Setup
- 36 -
CPU core 2 (Note)
Enables or disables CPU Core 2. (Default: Enabled)
CPU core 3 (Note)
Enables or disables CPU Core 3. (Default: Enabled)
CPU Clock Ratio
Allows you to alter the clock ratio for the installed CPU. The adjustable range is dependent on the CPU
being used.
CPU NorthBridge Freq.
Allows you to alter the North Bridge controller frequency for the installed CPU. The adjustable range is
dependent on the CPU being used.
CPU Host Clock Control
Enables or disables the control of CPU host clock. Auto (default) allows the BIOS to automatically adjust
the CPU host frequency. Manual allows the CPU Frequency (MHz) item below to be configurable.
Note: If your system fails to boot after overclocking, please wait for 20 seconds to allow for automated
system reboot, or clear the CMOS values to reset the board to default values.
CPU Frequency(MHz)
Allows you to manually set the CPU host frequency. The adjustable range is from 200 MHz to 500 MHz.
Important It is highly recommended that the CPU frequency be set in accordance with the CPU specifications.
PCIE Clock(MHz)
Allows you to manually set the PCIe clock frequency. The adjustable range is from 100 MHz to 150 MHz.
Auto sets the PCIe clock frequency to standard 100 MHz. (Default: Auto)
HT Link Frequency
Allows you to manually set the frequency for the HT Link between the CPU and chipset.
Auto
BIOS will automatically adjust the HT Link Frequency. (Default)
200 MHz~2 GHz Sets HT Link Frequency to 200 MHz~2 GHz.
Set Memory Clock
Determines whether to manually set the memory clock. Auto lets BIOS automatically set the memory
clock as required. Manual allows the memory clock control item below to be configurable. (Default: Auto)
Memory Clock
This option is configurable only when Set Memory Clock is set to Manual.
X4.00
Sets Memory Clock to X4.00.
X5.33
Sets Memory Clock to X5.33.
X6.66
Sets Memory Clock to X6.66.
X8.00
Sets Memory Clock to X8.00.
(Note)
This item is present only if you install a CPU that supports this feature.
- 37 -
BIOS Setup
DRAM Configuration
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
DRAM Configuration
x
x
x
x
x
x
x
x
x
x
x
x
x
x
DCTs Mode
DDR3 Timing Items
CAS# latency
RAS to CAS R/W Delay
Row Precharge Time
Minimum RAS Active Time
1T/2T Command Timing
TwTr Command Delay
Trfc0 for DIMM1
Trfc2 for DIMM2
Trfc1 for DIMM3
Trfc3 for DIMM4
Write Recovery Time
Precharge Time
Row Cycle Time
RAS to RAS Delay
Bank interleaving
Channel interleave
Enter: Select
: Move
F5: Previous Values
[Unganged]
[Auto]
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
[Enabled]
[Enabled]
SPD
7T
7T
7T
30T
--
5T
90ns
--
--
--
10T
5T
28T
4T
Auto
7T
7T
7T
30T
-5T
90ns
---10T
5T
28T
4T
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
Item Help
Menu Level 
ESC: Exit
F1: General Help
F7: Optimized Defaults
DCTs Mode
Allows you to set memory control mode.
Ganged
Sets memory control mode to single dual-channel.
Unganged
Sets memory control mode to two single-channel. (Default)
DDR3 Timing Items
Manual allows all DDR3 Timing items below to be configurable.
Options are: Auto (default), Manual.
CAS# latency
Options are: Auto (default), 4T~12T.
RAS to CAS R/W Delay
Options are: Auto (default), 5T~12T.
Row Precharge Time
Options are: Auto (default), 5T~12T.
Minimum RAS Active Time
Options are: Auto (default), 15T~30T.
1T/2T Command Timing
Options are: Auto (default), 1T, 2T.
TwTr Command Delay
Options are: Auto (default), 4T~7T.
Trfc0 for DIMM1
Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns.
Trfc2 for DIMM2
Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns.
Trfc1 for DIMM3
Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns.
BIOS Setup
- 38 -
Trfc3 for DIMM4
Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns.
Write Recovery Time
Options are: Auto (default), 5T~8T, 10T, 12T.
Precharge Time
Options are: Auto (default), 4T~7T.
Row Cycle Time
Options are: Auto (default), 11T~42T.
RAS to RAS Delay
Options are: Auto (default), 4T~7T.
Bank Interleaving
Enables or disables memory bank interleaving. Enabled allows the system to simultaneously access different banks of the memory to increase memory performance and stability. (Default: Enabled)
Channel interleave
Enables or disables memory channel interleaving. Enabled allows the system to simultaneously access
different channels of the memory to increase memory performance and stability. (Default: Enabled)
******** System Voltage Optimized ********
System Voltage Control
Determines whether to manually set the system voltages. Auto lets the BIOS automatically set the
system voltages as required. Manual allows all voltage control items below to be configurable. (Default:
Auto)
DRAM Voltage Control
Allows you to set the memory voltage.
Normal
Supplies the memory voltage as required. (Default)
1.500V ~ 2.380V The adjustable range is from 1.500V to 2.380V.
Note: Increasing memory voltage may result in damage to the memory or reduce the useful life of the
memory.
DDR VTT Voltage Control
Normal
Supplies the memory VTT voltage as required. (Default)
0.900V ~ 1.300V The adjustable range is from 0.900V to 1.300V.
Note: Increasing memory voltage may result in damage to the memory or reduce the useful life of the
memory
NB Voltage Control
Allows you to set the North Bridge voltage.
Normal
Supplies the North Bridge voltage as required. (Default)
1.100V ~ 1.800V The adjustable range is from 1.100V to 1.800V.
SB/HT Voltage Control
Allows you to set the South Bridge/HT-Link voltage.
Normal
Supplies the South Bridge/HT-Link voltage as required. (Default)
1.200V ~ 1.580V The adjustable range is from 1.200V to 1.580V.
- 39 -
BIOS Setup
NB PCIE Voltage Control
Allows you to set the North Bridge PCIe voltage.
Normal
Supplies the North Bridge PCIe voltage as required. (Default)
1.800V ~ 2.200V The adjustable range is from 1.800V to 2.200V.
CPU NB VID Control
Allows you to set the CPU Northbridge VID voltage. Auto sets the CPU Northbridge VID voltage as required. The adjustable range is dependent on the CPU being installed. (Default: Normal)
Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU.
CPU Voltage Control
Allows you to set the CPU voltage. Auto sets the CPU voltage as required. The adjustable range is dependent on the CPU being installed. (Default: Normal)
Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU.
Normal CPU Vcore
Displays the normal operating voltage of your CPU.
BIOS Setup
- 40 -
2-4 Standard CMOS Features
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Mon, Dec 21 2009
22:31:24
}
}
}
}
}
}
}
}
IDE Channel 0 Master
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
IDE Channel 2 Master
IDE Channel 2 Slave
IDE Channel 3 Master
IDE Channel 3 Slave
[None]
[None]
[None]
[None]
[None]
[None]
[None]
[None]
Drive A
Floppy 3 Mode Support [1.44M, 3.5"]
[Disabled]
Halt On
[All, But Keyboard]
Base Memory
Extended Memory
Enter: Select
: Move
F5: Previous Values
Item Help
Menu Level 
640K
1022M
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
Date (mm:dd:yy)
Sets the system date. The date format is week (read-only), month, date and year. Select the desired field
and use the up arrow or down arrow key to set the date.
Time (hh:mm:ss)
Sets the system time. For example, 1 p.m. is 13:0:0. Select the desired field and use the up arrow or
down arrow key to set the time.
IDE Channel 0, 1 Master/Slave
IDE HDD Auto-Detection
Press <Enter> to autodetect the parameters of the IDE/SATA device on this channel.
IDE Channel 0, 1 Master/Slave
Configure your IDE/SATA devices by using one of the two methods below:
• Auto
Lets the BIOS automatically detect IDE/SATA devices during the POST. (Default)
• None
If no IDE/SATA devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup.
Access Mode
Sets the hard drive access mode. Options are: Auto (default), CHS, LBA, Large.
IDE Channel 2, 3 Master/Slave
IDE Auto-Detection
Press <Enter> to autodetect the parameters of the IDE/SATA device on this channel.
Extended IDE Drive
Configure your IDE/SATA devices by using one of the two methods below:
• Auto
Lets the BIOS automatically detect IDE/SATA devices during the POST. (Default)
• None
If no IDE/SATA devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup.
Access Mode
Sets the hard drive access mode. Options are: Auto (default), Large.
The following fields display your hard drive specifications. If you wish to enter the parameters manually,
refer to the information on the hard drive.
Capacity
Approximate capacity of the currently installed hard drive.
- 41 -
BIOS Setup
Cylinder
Head
Precomp
Landing Zone
Sector
Drive A
Number of cylinders.
Number of heads.
Write precompensation cylinder.
Landing zone.
Number of sectors.
Allows you to select the type of floppy disk drive installed in your system. If you do not install a floppy
disk drive, set this item to None. Options are: None, 360K/5.25", 1.2M/5.25", 720K/3.5", 1.44M/3.5",
2.88M/3.5".
Floppy 3 Mode Support
Allows you to specify whether the installed floppy disk drive is 3-mode floppy disk drive, a Japanese
standard floppy disk drive. Options are: Disabled (default), Drive A.
Halt On
Allows you to determine whether the system will stop for an error during the POST.
All Errors
Whenever the BIOS detects a non-fatal error the system boot will stop.
No Errors
The system boot will not stop for any error.
All, But Keyboard The system boot will not stop for a keyboard error but stop for all other errors. (Default)
All, But Diskette
The system boot will not stop for a floppy disk drive error but stop for all other errors.
All, But Disk/Key
The system boot will not stop for a keyboard or a floppy disk drive error but it will stop for all other errors.
Memory
These fields are read-only and are determined by the BIOS POST.
Base Memory
Also called conventional memory. Typically, 640 KB will be reserved for the
MS-DOS operating system.
Extended Memory The amount of extended memory.
BIOS Setup
- 42 -
2-5 Advanced BIOS Features
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
Advanced BIOS Features
}
AMD C1E Support (Note)
Virtualization
AMD K8 Cool&Quiet control Hard Disk Boot Priority
First Boot Device
Second Boot Device
Third Boot Device
Password Check
HDD S.M.A.R.T. Capability
Away Mode
Full Screen LOGO Show
Backup BIOS Image to HDD
Init Display First
Enter: Select
: Move
F5: Previous Values
Item Help
Menu Level 
[Disabled]
[Disabled]
[Auto]
[Press Enter]
[Hard Disk]
[CDROM]
[Floppy]
[Setup]
[Disabled]
[Disabled]
[Enabled]
[Disabled]
[PCI Slot]
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
AMD C1E Support (Note)
Enables or disables the C1E CPU power-saving function in system halt state. When enabled, the CPU
core frequency and voltage will be reduced during system halt state to decrease power consumption.
(Default: Disabled)
Virtualization
Virtualization allows a platform to run multiple operating systems and applications in independent partitions. With virtualization, one computer system can function as multiple virtual systems.
(Default: Disabled)
AMD K8 Cool&Quiet control
Auto
Disabled
Lets the AMD Cool'n'Quiet driver dynamically adjust the CPU clock and VID to reduce heat output from your computer and its power consumption. (Default)
Disables this function.
Hard Disk Boot Priority
Specifies the sequence of loading the operating system from the installed hard drives. Use the up or
down arrow key to select a hard drive, then press the plus key <+> (or <PageUp>) or the minus key <-> (or
<PageDown>) to move it up or down on the list. Press <Esc> to exit this menu when finished.
First/Second/Third Boot Device
Specifies the boot order from the available devices. Use the up or down arrow key to select a device
and press <Enter> to accept. Options are: Floppy, LS120, Hard Disk, CDROM, ZIP, USB-FDD, USB-ZIP,
USB-CDROM, USB-HDD, Legacy LAN, Disabled.
(Note)
This item appears only if you install a CPU that supports this feature.
- 43 -
BIOS Setup
Password Check
Specifies whether a password is required every time the system boots, or only when you enter BIOS
Setup. After configuring this item, set the password(s) under the Set Supervisor/User Password item in
the BIOS Main Menu.
Setup
A password is only required for entering the BIOS Setup program. (Default)
System A password is required for booting the system and for entering the BIOS Setup program.
HDD S.M.A.R.T. Capability
Enables or disables the S.M.A.R.T. (Self Monitoring and Reporting Technology) capability of your hard
drive. This feature allows your system to report read/write errors of the hard drive and to issue warnings
when a third party hardware monitor utility is installed. (Default: Enabled)
Away Mode
Enables or disables Away Mode in Windows XP Media Center operating system. Away Mode allows the
system to silently perform unattended tasks while in a low-power mode that appears off.
(Default: Disabled)
Full Screen LOGO Show
Allows you to determine whether to display the GIGABYTE Logo at system startup. Disabled displays
normal POST message. (Default: Enabled)
Backup BIOS Image to HDD
Allows the system to copy the BIOS image file to the hard drive. If the system BIOS is corrupted, it will
be recovered from this image file. (Default: Disabled)
Init Display First
Specifies the first initiation of the monitor display from the installed PCI graphics card or the PCI Express
graphics card.
PCI
Sets the PCI graphics card as the first display. (Default)
PEG
Sets the PCI Express graphics card on the PCIEX16 slot as the first display.
BIOS Setup
- 44 -
2-6 Integrated Peripherals
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
Integrated Peripherals
x
}
x
OnChip SATA Controller
OnChip SATA Type
OnChip SATA Port4/5 Type
Onboard LAN Function
Onboard LAN Boot ROM
SMART LAN Onboard Audio Function
Onboard 1394 Function
Onboard USB 3.0 Controller
Onchip USB Controller
USB EHCI Controllers
USB Keyboard Support
USB Mouse Support
Legacy USB storage detect
Onboard Serial Port 1
Onboard Parallel Port
Parallel Port Mode
ECP Mode Use DMA
Enter: Select
: Move
F5: Previous Values
[Enabled]
[Native IDE]
IDE
[Enabled]
[Disabled]
[Press Enter]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Disabled]
[Enalbed]
[3F8/IRQ4]
[378/IRQ7]
[SPP]
3
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
Item Help
Menu Level 
ESC: Exit
F1: General Help
F7: Optimized Defaults
OnChip SATA Controller (AMD SB710 Chipset)
Enables or disables the SATA controller integrated in the AMD SB710 chip. (Default: Enabled)
OnChip SATA Type (AMD SB710, SATA2_0~SATA2_3 connectors)
Configures the operating mode of the integrated SATA2_0~SATA2_3 controller.
Native IDE
Allows the SATA controller to operate in Native IDE mode. (Default) Enable Native IDE mode if you wish to install operating systems that support Native mode.
RAID
Enables RAID for the SATA controller.
AHCI
Configures the SATA controllers to AHCI mode. Advanced Host Controller Interface (AHCI) is an interface specification that allows the storage driver to enable advanced Serial ATA features such as Native Command Queuing and hot plug.
OnChip SATA Port4/5 Type (AMD SB710, SATA2_4~SATA2_5 connectors)
This option is configurable only when OnChip SATA Type is set to RAID or AHCI. Configures the oper-
ating mode of the integrated SATA2_4/SATA2_5 connectors.
IDE
Disables RAID for the SATA controller and configures the SATA controller to PATA mode. (Default) As SATA Type The mode depends on the OnChip SATA Type settings.
Onboard LAN Function
Enables or disables the onboard LAN function. (Default: Enabled)
If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to
Disabled.
Onboard LAN Boot ROM
Allows you to decide whether to activate the boot ROM integrated with the onboard LAN chip.
(Default: Disabled)
- 45 -
BIOS Setup
SMART LAN (LAN Cable Diagnostic Function)
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
SMART LAN
Start detecting at Port.....
Part1-2 Status = Open
Part3-6 Status = Open
Part4-5 Status = Open
Part7-8 Status = Open
/
/
/
/
Length
Length
Length
Length
Enter: Select
: Move
F5: Previous Values
=
=
=
=
Item Help
Menu Level 
0m
0m
0m
0m
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
This motherboard incorporates cable diagnostic feature designed to detect the status of the attached LAN
cable. This feature will detect cabling issue and report the approximate distance to the fault or short. Refer to
the following information for diagnosing your LAN cable:
When No LAN Cable Is Attached...
If no LAN cable is attached to the motherboard, the Status fields of all four pairs of wires will show Open
and the Length fields show 0m, as shown in the figure above.
When LAN Cable Is Functioning Normally...
If no cable problem is detected on the LAN cable connected to a Gigabit hub or a 10/100 Mbps hub, the
following message will appear:
Start detecting at Port.....
Link Detected --> 100Mbps
Cable Length= 30m
Link Detected Displays transmission speed.
Cable Length Displays the approximate length of the attached LAN cable.
Note: The Gigabit hub will only operate at a speed of 10/100 Mbps in MS-DOS mode; it will operate at a
normal speed of 10/100/1000 Mbps in Windows mode or when the LAN Boot ROM is activated.
When a Cable Problem Occurs...
If a cable problem occurs on a specified pair of wires, the Status field will show Short and then length
shown will be the approximate distance to the fault or short.
Example: Part1-2 Status = Short / Length = 2m
Explanation: A fault or short might occur at about 2m on Part 1-2.
Note: Part 4-5 and Part 7-8 are not used in a 10/100 Mbps environment, so their Status fields will show
Open, and the length shown is the approximate length of the attached LAN cable.
Onboard Audio Function
Enables or disables the onboard audio function. (Default: Enabled)
If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to
Disabled.
Onboard 1394 Function
Enables or disables the onboard IEEE 1394 function. (Default: Enabled)
Onboard USB 3.0 Controller (NEC USB 3.0 Controller)
Enables or disables the NEC USB 3.0 controller. (Default: Enabled)
BIOS Setup
- 46 -
Onchip USB Controllers (Onboard USB 1.1 Controllers)
Enables or disables the integrated USB 1.1 controller. (Default: Enabled)
Disabled will turn off all of the USB functionalities below.
USB EHCI Controller (Onboard USB 2.0 Controllers)
Enables or disables the integrated USB 2.0 controller. (Default: Enabled)
USB Keyboard Support
Allows USB keyboard to be used in MS-DOS. (Default: Enabled)
USB Mouse Support
Allows USB mouse to be used in MS-DOS. (Default: Disabled)
Legacy USB storage detect
Determines whether to detect USB storage devices, including USB flash drives and USB hard drives during the POST. (Default: Enabled)
Onboard Serial Port 1
Enables or disables the first serial port and specifies its base I/O address and corresponding interrupt.
Options are: Auto, 2F8/IRQ3, 3F8/IRQ4(default), 3E8/IRQ4, 2E8/IRQ3, Disabled.
Onboard Parallel Port
Enables or disables the onboard parallel port (LPT) and specifies its base I/O address and corresponding interrupt. Options are: 378/IRQ7 (default), 278/IRQ5, 3BC/IRQ7, Disabled.
Parallel Port Mode
Selects an operating mode for the onboard parallel (LPT) port. Options are: SPP (Standard Parallel Port)
(default), EPP (Enhanced Parallel Port), ECP (Extended Capabilities Port), ECP+EPP.
ECP Mode Use DMA
Selects DMA channel for the LPT port in ECP mode. This item is configurable only if Parallel Port Mode
is set to ECP or ECP+EPP mode. Options are: 3 (default), 1.
- 47 -
BIOS Setup
2-7 Power Management Setup
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
Power Management Setup
x
x
x
ACPI Suspend Type
Soft-Off by Power button
USB Wake Up from S3
Modem Ring Resume
PME Event Wake Up
HPET Support (Note)
Power On By Mouse
Power On By Keyboard
KB Power ON Password
AC Back Function
Power-On by Alarm
Date (of Month)
Resume Time (hh:mm:ss)
EuP Support
Enter: Select
: Move
F5: Previous Values
[S3(STR)]
[Instant-off]
[Enabled]
[Disabled]
[Enabled]
[Enabled] [Disabled]
[Disabled]
Enter
[Soft-Off]
[Disabled]
Everyday
0:0:0
[Disabled]
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
Item Help
Menu Level 
ESC: Exit
F1: General Help
F7: Optimized Defaults
ACPI Suspend Type
Specifies the ACPI sleep state when the system enters suspend.
S1(POS)
Enables the system to enter the ACPI S1 (Power on Suspend) sleep state. In S1 sleep state, the system appears suspended and stays in a low power mode. The system can be resumed at any time.
S3(STR)
Enables the system to enter the ACPI S3 (Suspend to RAM) sleep state (default). In S3 sleep state, the system appears to be off and consumes less power than in the S1 state. When signaled by a wake-up device or event, the system resumes to its working state exactly where it was left off.
Soft-Off by Power button
Configures the way to turn off the computer in MS-DOS mode using the power button.
Instant-Off
Press the power button and then the system will be turned off instantly. (Default)
Delay 4 Sec. Press and hold the power button for 4 seconds to turn off the system. If the power button is pressed for less than 4 seconds, the system will enter suspend mode.
USB Wake Up from S3
Allows the system to be awakened from ACPI S3 sleep state by a wake-up signal from the installed USB
device. (Default: Enabled)
Modem Ring Resume
Allows the system to be awakened from an ACPI sleep state by a wake-up signal from a modem that
supports wake-up function. (Default: Disabled)
PME Event Wake Up
Allows the system to be awakened from an ACPI sleep state by a wake-up signal from a PCI or PCIe device. Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.
(Default: Enabled)
(Note)
Supported on Windows 7/Vista operating system only.
BIOS Setup
- 48 -
HPET Support (Note)
Enables or disables High Precision Event Timer (HPET) for Windows 7/Vista operating system.
(Default: Enabled)
Power On By Mouse
Allows the system to be turned on by a PS/2 mouse wake-up event.
Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.
Disabled
Disables this function. (Default)
Double Click Double click on left button on the PS/2 mouse to turn on the system.
Power On By Keyboard
Allows the system to be turned on by a PS/2 keyboard wake-up event.
Note: you need an ATX power supply providing at least 1A on the +5VSB lead.
Disabled
Disables this function. (Default)
Password
Set a password with 1~5 characters to turn on the system.
Any KEY
Press any key on the keyboard to turn on the system.
Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system.
KB Power ON Password
Set the password when Power On by Keyboard is set to Password. Press <Enter> on this item and set
a password with up to 5 characters and then press <Enter> to accept. To turn on the system, enter the
password and press <Enter>.
Note: To cancel the password, press <Enter> on this item. When prompted for the password, press <Enter> again without entering the password to clear the password settings.
AC Back Function
Determines the state of the system after the return of power from an AC power loss.
Soft-Off
The system stays off upon the return of the AC power. (Default)
Full-On
The system is turned on upon the return of the AC power.
Memory
The system returns to its last known awake state upon the return of the AC power.
Power-On by Alarm
Determines whether to power on the system at a desired time. (Default: Disabled)
If enabled, set the date and time as following:
Date (of Month) Alarm: Turn on the system at a specific time on each day or on a specific day in a
month.
Resume Time (hh: mm: ss): Set the time at which the system will be powered on automatically.
Note: When using this function, avoid inadequate shutdown from the operating system or removal of the
AC power, or the settings may not be effective.
EuP Support
Determines whether to let the system consume less than 1W power in S5 (shutdown) state. (Default:
Disabled)
Note: When this item is set to Enabled, the following four functions will become unavailable:
PME event wake up, power on by mouse, power on by keyboard, and wake on LAN.
(Note)
Supported on Windows 7/Vista operating system only.
- 49 -
BIOS Setup
2-8 PC Health Status
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
PC Health Status
Hardware Thermal Control
Reset Case Open Status
Case Opened
Vcore
DDR3 1.5V
+3.3V
+12V
Current System Temperature
Current CPU Temperature
Current CPU FAN Speed
Current SYSTEM FAN1 Speed
Current SYSTEM FAN2 Speed
Current POWER FAN Speed
CPU Warning Temperature
CPU FAN Fail Warning
SYSTEM FAN1 Fail Warning
SYSTEM FAN2 Fail Warning
POWER FAN Fail Warning
CPU Smart FAN Control
Enter: Select
: Move
F5: Previous Values
Item Help
Menu Level 
[Enabled] [Disabled]
No
1.364V
1.536V
3.280V
12.048V
38oC
36oC
1962 RPM
0 RPM
0 RPM
0 RPM
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Enabled]
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
PC Health Status
CPU Smart FAN Mode System Smart FAN Control
Enter: Select
: Move
F5: Previous Values
[Auto]
[Enabled]
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
Item Help
Menu Level 
ESC: Exit
F1: General Help
F7: Optimized Defaults
Hardware Thermal Control
Enables or disables the CPU overheating protection function. When enabled, the CPU core voltage and
ratio will be reduced when the CPU is overheated. (Default: Enabled)
Reset Case Open Status
Keeps or clears the record of previous chassis intrusion status. Enabled clears the record of previous
chassis intrusion status and the Case Opened field will show "No" at next boot. (Default: Disabled)
Case Opened
Displays the detection status of the chassis intrusion detection device attached to the motherboard CI
header. If the system chassis cover is removed, this field will show "Yes", otherwise it will show "No". To
clear the chassis intrusion status record, set Reset Case Open Status to Enabled, save the settings to
the CMOS, and then restart your system.
BIOS Setup
- 50 -
Current Voltage(V) Vcore/DDR3 1.5V/+3.3V/+12V
Displays the current system voltages.
Current System/CPU Temperature
Displays current system/CPU temperature.
Current CPU/SYSTEM/POWER FAN Speed (RPM)
Displays current CPU/system/power fan speed.
CPU Warning Temperature
Sets the warning threshold for CPU temperature. When CPU temperature exceeds the threshold,
BIOS will emit warning sound. Options are: Disabled (default), 60oC/140oF, 70oC/158oF, 80oC/176oF,
90oC/194oF.
CPU/SYSTEM/POWER FAN Fail Warning
Allows the system to emit warning sound if the CPU/system/power fan is not connected or fails. Check
the fan condition or fan connection when this occurs. (Default: Disabled)
CPU Smart FAN Control
Enables or disables the CPU fan speed control function. Enabled allows the CPU fan to run at different
speed according to the CPU temperature. You can adjust the fan speed with EasyTune based on system
requirements. If disabled, the CPU fan runs at full speed. (Default: Enabled)
CPU Smart FAN Mode
Specifies how to control CPU fan speed. This item is configurable only if CPU Smart FAN Control is set
to Enabled.
Auto
Lets the BIOS automatically detect the type of CPU fan installed and sets the optimal
CPU fan control mode. (Default)
Voltage Sets Voltage mode for a 3-pin CPU fan.
PWM
Sets PWM mode for a 4-pin CPU fan.
System Smart FAN Control
Enables or disables the system fan speed control function. Enabled allows the system fan to run at different speed according to the system temperature. You can adjust the fan speed with EasyTune based
on system requirements. If disabled, system fan runs at full speed. (Default: Enabled)
- 51 -
BIOS Setup
2-9 Load Fail-Safe Defaults
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software






MB Intelligent Tweaker(M.I.T.)
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PC Health Status
ESC: Quit F8: Q-Flash
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
(Y/N)?
Save
Load Fail-Safe Defaults
N & Exit Setup
Exit Without Saving
: Select Item
F10: Save & Exit Setup
F11: Save CMOS to BIOS
F12: Load CMOS from BIOS
Load Fail-Safe Defaults
Press <Enter> on this item and then press the <Y> key to load the safest BIOS default settings.
In case system instability occurs, you may try to load Fail-Safe defaults, which are the safest and most stable
BIOS settings for the motherboard.
2-10 Load Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software






MB Intelligent Tweaker(M.I.T.)
Load Fail-Safe Defaults
Standard CMOS Features
Load Optimized Defaults
Advanced BIOS Features
Set Supervisor Password
Integrated Peripherals
Set User Password
Power Management Setup
(Y/N)?
Save
Load Optimized Defaults
N & Exit Setup
PC Health Status
Exit Without Saving
ESC: Quit F8: Q-Flash
: Select Item
F10: Save & Exit Setup
F11: Save CMOS to BIOS
F12: Load CMOS from BIOS
Load Optimized Defaults
Press <Enter> on this item and then press the <Y> key to load the optimal BIOS default settings.
The BIOS defaults settings help the system to operate in optimum state. Always load the Optimized defaults
after updating the BIOS or after clearing the CMOS values.
BIOS Setup
- 52 -
2-11 Set Supervisor/User Password
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software






MB Intelligent Tweaker(M.I.T.)
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management SetupEnter Password:
PC Health Status
ESC: Quit F8: Q-Flash
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
: Select Item
F10: Save & Exit Setup
F11: Save CMOS to BIOS
F12: Load CMOS from BIOS
Change/Set/Disable Password
Press <Enter> on this item and type the password with up to 8 characters and then press <Enter>. You will
be requested to confirm the password. Type the password again and press <Enter>.
The BIOS Setup program allows you to specify two separate passwords:
Supervisor Password
When a system password is set and the Password Check item in Advanced BIOS Features is set to
Setup, you must enter the supervisor password for entering BIOS Setup and making BIOS changes.
When the Password Check item is set to System, you must enter the supervisor password (or user
password) at system startup and when entering BIOS Setup.
User Password
When the Password Check item is set to System, you must enter the supervisor password (or user
password) at system startup to continue system boot. In BIOS Setup, you must enter the supervisor
password if you wish to make changes to BIOS settings. The user password only allows you to view the
BIOS settings but not to make changes.
To clear the password, press <Enter> on the password item and when requested for the password, press
<Enter> again. The message "PASSWORD DISABLED" will appear, indicating the password has been cancelled.
- 53 -
BIOS Setup
2-12 Save & Exit Setup
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software






MB Intelligent Tweaker(M.I.T.)
Load Fail-Safe Defaults
Standard CMOS Features
Load Optimized Defaults
Save to CMOS and EXIT (Y/N)? Y
Advanced BIOS Features
Set Supervisor Password
Integrated Peripherals
Set User Password
Power Management Setup
Save & Exit Setup
PC Health Status
Exit Without Saving
ESC: Quit F8: Q-Flash
: Select Item
F10: Save & Exit Setup
F11: Save CMOS to BIOS
F12: Load CMOS from BIOS
Save Data to CMOS
Press <Enter> on this item and press the <Y> key. This saves the changes to the CMOS and exits the BIOS
Setup program. Press <N> or <Esc> to return to the BIOS Setup Main Menu.
2-13 Exit Without Saving
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software






MB Intelligent Tweaker(M.I.T.)
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PC Health Status
ESC: Quit F8: Q-Flash
Load Fail-Safe Defaults
Load Optimized Defaults
Quit Without Saving (Y/N)? N
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
: Select Item
F10: Save & Exit Setup
F11: Save CMOS to BIOS
F12: Load CMOS from BIOS
Abandon all Data
Press <Enter> on this item and press the <Y> key. This exits the BIOS Setup without saving the changes
made in BIOS Setup to the CMOS. Press <N> or <Esc> to return to the BIOS Setup Main Menu.
BIOS Setup
- 54 -
Chapter 3 Drivers Installation
• Before installing the drivers, first install the operating system.
• After installing the operating system, insert the motherboard driver disk into your optical drive.
The driver Autorun screen is automatically displayed which looks like that shown in the screen
shot below. (If the driver Autorun screen does not appear automatically, go to My Computer,
double-click the optical drive and execute the Run.exe program.)
3-1 Installing Chipset Drivers
After inserting the driver disk, "Xpress Install" will automatically scan your system and then list all the drivers
that are recommended to install. You can click the Install All button and "Xpress Install" will install all the recommended drivers. Or click Install Single Items to manually select the drivers you wish to install.
• Please ignore the popup dialog box(es) (e.g. the Found New Hardware Wizard) displayed
when "Xpress Install" is installing the drivers. Failure to do so may affect the driver installation.
• Some device drivers will restart your system automatically during the driver installation. After the
system restart, "Xpress Install" will continue to install other drivers.
• After the drivers are installed, follow the on-screen instructions to restart your system. You can
install other applications included in the motherboard driver disk.
• For USB 2.0 driver support under the Windows XP operating system, please install the Windows
XP Service Pack 1 or later. After installing the SP1 (or later), if a question mark still exists in
Universal Serial Bus Controller in Device Manager, please remove the question mark (by
right-clicking your mouse and select Uninstall) and restart the system. (The system will then
autodetect and install the USB 2.0 driver.)
- 55 -
Drivers Installation
3-2 Application Software
This page displays all the utilities and applications that GIGABYTE develops and some free software. You
can click the Install button on the right of an item to install it.
3-3 Technical Manuals
This page provides GIGABYTE's application guides, content descriptions for this driver disk, and the motherboard manuals.
Drivers Installation
- 56 -
3-4 Contact
For the detailed contact information of the GIGABYTE Taiwan headquarter or worldwide branch offices, click
the URL on this page to link to the GIGABYTE website.
3-5 System
This page provides the basic system information.
- 57 -
Drivers Installation
3-6 Download Center
To update the BIOS, drivers, or applications, click the Download Center button to link to the GIGABYTE
website. The latest version of the BIOS, drivers, or applications will be displayed.
Drivers Installation
- 58 -
Chapter 4 Unique Features
4-1 Xpress Recovery2
Xpress Recovery2 is a utility that allows you to quickly compress and
back up your system data and perform restoration of it. Supporting NTFS,
FAT32, and FAT16 file systems, Xpress Recovery2 can back up data on
PATA and SATA hard drives and restore it.
Before You Begin:
• Xpress Recovery2 will check the first physical hard drive (Note) for the operating system. Xpress Recovery2
can only back up/restore the first physical hard drive that has the operating system installed.
• As Xpress Recovery2 will save the backup file at the end of the hard drive, make sure to leave enough unallocated space in advanced (10 GB or more is recommended; actual size requirements vary, depending
on the amount of data).
• It is recommended to back up your system soon after the operating system and drivers are installed.
• The amount of data and hard drive access speed may affect the speed at which the data is backed up/
restored.
• It takes longer to back up a hard drive than to restore it.
System Requirements:
• At least 512 MB of system memory
• VESA compatible graphics card
• Windows XP with SP1 or later, Windows Vista
• Xpress Recovery and Xpress Recovery2 are different utilities. For example, a backup file created
with Xpress Recovery cannot be restored using Xpress Recovery2.
• USB hard drives are not supported.
• Hard drives in RAID/AHCI mode are not supported.
Installation and Configuration:
Turn on your system to boot from the Windows Vista setup disk.
A. Installing Windows Vista and Partitioning the Hard Drive
Step 1:
Click Drive options.
Step 2:
Click New.
(Note) Xpress Recovery2 checks the first physical hard drive in the following sequence: The first PATA IDE connector, the
second PATA IDE connector, the first SATA connector, the second SATA connector and so forth. For example, when hard
drives are attached to the first IDE and the first SATA connectors, the hard drive on the first IDE connector is the first physical
drive. When hard drives are attached to the first and second SATA connectors, the hard drive on the first SATA connector is
the first physical drive.
- 59 -
Unique Features
Step 3:
When partitioning your hard drive, make sure to
leave unallocated space (10 GB or more is recommended; actual size requirements vary, depending
on the amount of data) and begin the installation of
the operating system.
Step 4:
After the operating system is installed, right-click
the Computer icon on your desktop and select
Manage. Go to Disk Management to check disk
allocation.
Step 5:
Xpress Recovery2 will save the backup file to the unallocated
space (black stripe along the top). Please note that if there is no
enough unallocated space, Xpress Recovery2 cannot save the
backup file.
B. Accessing Xpress Recovery2
1. Boot from the motherboard driver disk to access Xpress Recovery2 for the first time. When you see the
following message: Press any key to startup Xpress Recovery2, press any key
to enter Xpress Recovery2.
2. After you use the backup function in Xpress Recovery2 for the first time, Xpress Recovery2 will stay
permanent in your hard drive. If you wish to enter Xpress Recovery2 later, simply press <F9> during the
POST.
C. Using the Backup Function in Xpress Recovery2
Xpress Recovery2 will automatically create a
new partition to store the backup image file.
Step 1:
Select BACKUP to start backing up your hard drive
data.
Unique Features
Step 2:
When finished, go to Disk Management to check
disk allocation.
- 60 -
D. Using the Restore Function in Xpress Recovery2
Select RESTORE to restore the backup to your hard drive in
case the system breaks down. The RESTORE option will not be
present if no backup is created before.
E. Removing the Backup
Step 1:
If you wish to remove the backup file, select
REMOVE.
Step 2:
After the backup file is removed, no backup image
file will be present in Disk Management and hard
drive space will be freed up.
F. Exiting Xpress Recovery2
Select REBOOT to exit Xpress Recovery2.
- 61 -
Unique Features
4-2 BIOS Update Utilities
GIGABYTE motherboards provide two unique BIOS update tools, Q-Flash™ and @BIOS™. GIGABYTE
Q-Flash and @BIOS are easy-to-use and allow you to update the BIOS without the need to enter MS-DOS
mode. Additionally, this motherboard features the DualBIOS™ design, which enhances protection for the
safety and stability of your computer by adding one more physical BIOS chip.
What is DualBIOS™?
Motherboards that support DualBIOS have two BIOS onboard, a main BIOS and
a backup BIOS. Normally, the system works on the main BIOS. However, if the
main BIOS is corrupted or damaged, the backup BIOS will take over on the next system boot and copy the
BIOS file to the main BIOS to ensure normal system operation. For the sake of system safety, users cannot
update the backup BIOS manually.
What is Q-Flash™?
With Q-Flash you can update the system BIOS without having to enter operating
systems like MS-DOS or Window first. Embedded in the BIOS, the Q-Flash tool
frees you from the hassles of going through complicated BIOS flashing process.
site and update the BIOS.
What is @BIOS™?
@BIOS allows you to update the system BIOS while in the Windows environment. @BIOS will download the latest BIOS file from the nearest @BIOS server
4-2-1 Updating the BIOS with the Q-Flash Utility
A. Before You Begin
1. From GIGABYTE's website, download the latest compressed BIOS update file that matches your motherboard model.
2. Extract the file and save the new BIOS file (e.g. 770tusb3.f1) to your USB flash drive or USB hard drive.
Note: The USB flash drive or hard drive must use FAT32/16/12 file system.
3. Restart the system. During the POST, press the <End> key to enter Q-Flash. Note: You can access
Q-Flash by either pressing the <End> key during the POST or pressing the <F8> key in BIOS Setup.
However, if the BIOS update file is saved to a hard drive in RAID/AHCI mode or a hard drive attached to
an independent IDE/SATA controller, use the <End> key during the POST to access Q-Flash.
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2009, Award Software, Inc.
AMD 770 BIOS for GA-770T-USB3 E7
.
.
.
.
<DEL>: BIOS Setup <F9>: XpressRecovery2 <F12>: Boot Menu <End>: Qflash
12/14/2009-RX780-SB710-7A66AG0WC-00
Because BIOS flashing is potentially risky, please do it with caution. Inadequate BIOS flashing may
result in system malfunction.
Unique Features
- 62 -
B. Updating the BIOS
When updating the BIOS, choose the location where the BIOS file is saved. The following procedure assumes that you save the BIOS file to a USB flash drive.
Step 1:
1. Insert the USB flash drive containing the BIOS file into the computer. In the main menu of Q-Flash, use
the up or down arrow key to select Update BIOS from Drive and press <Enter>.
• The Save Main BIOS to Drive option allows you to save the current BIOS file.
• Q-Flash only supports USB flash drive or hard drives using FAT32/16/12 file system.
• If the BIOS update file is saved to a hard drive in RAID/AHCI mode or a hard drive attached to
an independent IDE/SATA controller, use the <End> key during the POST to access Q-Flash.
2. Select HDD 0-0 and press <Enter>.
Q-Flash Utility v2.13
Flash Type/Size.................................
MXIC 25L8005
1M
0 file(s) found
Keep DMI Data Enable
HDD 0-0
Load CMOS Default Enable <Drive>
Update BIOS from Drive
Save BIOS to Drive
Enter : Run
ESC:Reset
F10:Power Off
hi:Move
Total size : 0
Free size : 0
3. Select the BIOS update file and press <Enter>.
Make sure the BIOS update file matches your motherboard model.
Step 2:
The process of the system reading the BIOS file from the USB flash drive is displayed on the screen. When
the message "Are you sure to update BIOS?" appears, press <Enter> to begin the BIOS update. The monitor
will display the update process.
• Do not turn off or restart the system when the system is reading/updating the BIOS.
• Do not remove the USB flash drive or hard drive when the system is updating the BIOS.
Step 3:
When the update process is complete, press any key to return to the main menu.
Q-Flash Utility v2.13
Flash Type/Size.................................
MXIC 25L8005
Keep DMI Data Enable
!!Load
CopyCMOS
BIOS Default
completed
- Pass !!
Enable
Update BIOS from Drive
pressBIOS
any key
to continue
Please Save
to Drive
Enter : Run
ESC:Reset
hi:Move
- 63 -
1M
F10:Power Off
Unique Features
Step 4:
Press <Esc> and then <Enter> to exit Q-Flash and reboot the system. As the system boots, you should see
the new BIOS version is present on the POST screen.
Step 5:
During the POST, press <Delete> to enter BIOS Setup. Select Load Optimized Defaults and press <Enter>
to load BIOS defaults. System will re-detect all peripheral devices after a BIOS update, so we recommend
that you reload BIOS defaults.
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software






MB Intelligent Tweaker(M.I.T.)
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PC Health Status
ESC: Quit F8: Q-Flash
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
(Y/N)?
Save
Load Fail-Safe Defaults
Y & Exit Setup
Exit Without Saving
: Select Item
F10: Save & Exit Setup
F11: Save CMOS to BIOS
F12: Load CMOS from BIOS
Load Fail-Safe Defaults
Press <Y> to load BIOS defaults
Step 6:
Select Save & Exit Setup and then press <Y> to save settings to CMOS and exit BIOS Setup. The procedure is complete after the system restarts.
Unique Features
- 64 -
4-2-2 Updating the BIOS with the @BIOS Utility
A. Before You Begin
1. In Windows, close all applications and TSR (Terminate and Stay Resident) programs. This helps prevent
unexpected failures when performing a BIOS update.
2. During the BIOS update process, ensure the Internet connection is stable and do NOT interrupt the
Internet connection (for example, avoid a power loss or switching off the Internet). Failure to do so may
result in a corrupted BIOS or a system that is unable to start.
3. Do not use the G.O.M. (GIGABYTE Online Management) function when using @BIOS.
4. GIGABYTE product warranty does not cover any BIOS damage or system failure resulting from an inadequate BIOS flashing.
B. Using @BIOS
1.
Update the BIOS Using the Internet Update Function:
Click Update BIOS from GIGABYTE Server, select the @BIOS server site closest to your location and
then download the BIOS file that matches your motherboard model. Follow the on-screen instructions to
complete.
If the BIOS update file for your motherboard is not present on the @BIOS server site, please
manually download the BIOS update file from GIGABYTE's website and follow the instructions in
"Update the BIOS without Using the Internet Update Function" below.
2.
Update the BIOS without Using the Internet Update Function:
Click Update BIOS from File, then select the location where you save the BIOS update file obtained
from the Internet or through other source. Follow the on-screen instructions to complete.
3.
Save the Current BIOS File:
Click Save Current BIOS to File to save the current BIOS file.
4.
Load BIOS Defaults after BIOS Update:
Select the Load CMOS default after BIOS update check box and then the system will automatically
load BIOS defaults after BIOS update and after the system restarts.
C. After Updating the BIOS
Restart your system after updating the BIOS.
Make sure that the BIOS file to be flashed matches your motherboard model. Updating the
BIOS with an incorrect BIOS file could cause your system not to boot.
- 65 -
Unique Features
4-3 EasyTune 6
GIGABYTE's EasyTune 6 is a simple and easy-to-use interface that allows users to fine-tune their system
settings or do overclock/overvoltage in Windows environment. The user-friendly EasyTune 6 interface also
includes tabbed pages for CPU and memory information, letting users read their system-related information
without the need to install additional software.
The EasyTune 6 Interface
Tabs Information
Tab
Function
The CPU tab provides information on the installed CPU and motherboard.
The Memory tab provides information on the installed memory module(s). You can select memory module on a specific slot to see its information.
The Tuner tab allows you to change system clock settings and voltages.
• Easy mode allows you to adjust the CPU FSB only.
• Advanced mode allows you to individually change system clock settings and voltages settings using the sliders.
• Easy Boost is an easy-to-use auto-overclocking function (Note 1). When activated, the system automatically experiments all sorts of overclocking configurations till it hangs. After restart, the system will operate with the optimum configurations tested to let the CPU reach the best overclocking performance.
• Core Boost is configurable only in Advanced mode. With Core Boost (Note 2) enabled, you can unlock hidden CPU cores or disable the cores that have been activated (Note 3).
• Save allows you to save the current settings to a new profile (.txt file).
• Load allows you to load previous settings from a profile.
After making changes in Easy mode/Advanced mode, be sure to click Set for these changes to take effect or click Default to restore to default values.
The Graphics tab allows you to change the core clock and memory clock for your ATI or NVIDIA graphics card.
The Smart tab allows you to specify a C.I.A.2 level and a Smart Fan mode. Smart Fan Advance Mode allows the CPU fan speed to be changed linearly based on the CPU temperature thresholds you set.
The HW Monitor tab allows you to monitor hardware temperature, voltage and fan speed and set temperature/fan speed alarm. You can choose the alert sound from the buzzer or use your own sound file (.wav file).
(Note 1)Before enabling Easy Boost, right-click the EasyTune 6 icon
in the notification area. Select Auto overclock
last tune on the next reboot to allow the system to work with the optimum overclocking configuration after restart.
(Note 2) Restart the computer after enabling Core Boost for the settings to take effect.
(Note 3) The number of CPU cores that can be enabled/disabled depends on the CPU being used.
Available functions in EasyTune 6 may differ by motherboard model. Grayed-out area(s) indicates that the item is
not configurable or the function is not supported.
Incorrectly doing overclock/overvoltage may result in damage to the hardware components such as CPU, chipset,
and memory and reduce the useful life of these components. Before you do the overclock/overvoltage, make sure
that you fully know each function of EasyTune 6, or system instability or other unexpected results may occur.
Unique Features
- 66 -
4-4 Easy Energy Saver
GIGABYTE Easy Energy Saver is a revolutionary technology that delivers unparalleled power savings with
a click of the button. Featuring an advanced proprietary software design, GIGABYTE Easy Energy Saver is
able to provide exceptional power savings and enhanced power efficiency without sacrificing computing performance.
The Easy Energy Saver Interface
A. Meter Mode
In Meter Mode, GIGABYTE Easy Energy Saver shows how much power they have saved in a set period of
time.
Meter Mode - Button Information Table
1 2
3
4
5
6
7
8
9
10
11
12
13
14
15
Button Description
Easy Energy Saver On/Off Switch (Default: Off)
Dynamic CPU Frequency Function On/Off Switch (Default: Off) (Note 1)
CPU Throttling Display
CPU Voltage Display
3-Level CPU Voltage Switch (Default:1) (Note 2)
Current CPU Power Consumption
Meter Time
Power Saving (Calculate power savings based on time)
Meter/Timer Reset Switch
Meter Mode Switch
Total Mode Switch
Close (Application will enter Stealth Mode)
Minimize (Application will continue to run in taskbar)
INFO/Help
Live Utility Update (Check for the latest utility version)
• The above data is for reference only. Actual performance may vary depending on motherboard model.
• CPU Power and Power Scores are for reference only. Actual results may vary based on testing method.
- 67 -
Unique Features
B. Total Mode
In Total Mode, users are able to see how much total power savings they have accumulated in a set period of
time since activating Easy Energy Saver for the first time (Note 3).
Total Mode - Button Information Table
1 2
3
4
5
6
7
8
9
10
11
12
13
14
Button Description
Easy Energy Saver On/Off Switch (Default: Off)
Dynamic CPU Frequency Function On/Off Switch (Default: Off) (Note 1)
CPU Throttling Display
CPU Voltage Display
3-Level CPU Voltage Switch (Default:1) (Note 2)
Current CPU Power Consumption
Time/Date Easy Energy Saver Enabled
Total Power Savings (Total power saving with Easy Energy Saver enabled) (Note 4)
Meter Mode Switch
Total Mode Switch
Close (Application will enter Stealth Mode)
Minimize (Application will continue to run in taskbar)
INFO/Help
Live Utility Update (Check for the latest utility version)
C. Stealth Mode
In Stealth Mode, the system continues to work with the user-defined power saving settings, even after the
system is restarted. Re-enter the application only if you want to make any changes or completely close the
application.
(Note 1) Maximize system power saving with Dynamic CPU Frequency Function; system performance may
be affected.
(Note 2) 1: Normal Power Saving (default); 2: Advanced Power Saving; 3: Extreme Power Saving.
(Note 3) The total amount of power saved will be recorded until re-activated when only the Easy Energy
Saver is under the enable status, and power savings meter is unable to reset to zero.
(Note 4) Easy Energy Saver Meter will automatically reset when the total power saving reaches 99999999
Watts.
Unique Features
- 68 -
4-5 Q-Share
Q-Share is an easy and convenient data sharing tool. After configuring your LAN connection settings and
Q-Share, you are able to share your data with computers on the same network, making full use of Internet
resources.
Directions for using Q-Share
After installing Q-Share from the motherboard driver disk, go to Start>All Programs>GIGABYTE>Q-Share.
exe to launch the Q-Share tool. Find the Q-Share icon
in the notification area and right-click on this icon
to configure the data sharing settings.
Figure 1. Data Sharing Disabled
Options Descriptions
Option
Connect ...
Enable Incoming Folder ...
Disable Incoming Folder ...
Open Incoming Folder :
C:\Q-ShareFolder
Change Incoming Folder :
C:\Q-ShareFolder
Update Q-Share ...
About Q-Share ... Exit...
(Note)
Figure 2. Data Sharing Enabled
Description
Displays the computers with data sharing enabled
Enables data sharing
Disables data sharing
Accesses the shared data folder
Changes the data folder to be shared (Note)
Updates Q-Share online
Displays the current Q-Share version
Exits Q-Share
This option is available only when data sharing is NOT enabled.
- 69 -
Unique Features
4-6 SMART Recovery
With SMART Recovery, users can quickly create backups of changed data files (Note 1) or copy files from a specific backup on PATA and SATA hard drives (partitioned on NTFS file system) in Windows Vista.
Instructions:
In the main menu, click the Config button to open the Smart Recovery Preference dialog box.
The Smart Recovery Preference dialog box:
Button
Enable Schedule
Capacity
Function
Enables automatic daily backup (Note 2)
Sets a daily backup schedule
Sets the percentage of hard drive space used for saving backups (Note 3)
• The hard drive must have more than 1 GB of capacity.
• Each partition can accommodate up to 64 backups (the actual
limit depends on the size of each partition). When this limit is
reached, the oldest backup will be ovewritten.
Instructions for copying files/folders from a backup:
To browse through your backups made at different time, select a
backup time using the time scroll bar on the right or at the bottom of
the screen. If you want to copy back a file/folder, select the file/folder
you wish to copy and click the Copy button.
The files/folders listed on the screen are read-only so you cannot edit
their contents.
(Note 1) The changed data refers to the data that has been modified, deleted, or newly added since the last backup.
(Note 2) The system will make an automatic backup on changed data only once everyday. If the computer is turned on for
a long time, the backup will be performed at the scheduled backup time. If the computer is turned off before the
scheduled backup time, the backup will be performed on the next boot.
(Note 3) We recommend that you preserve at least 25 percent of the hard drive space to optimize the storage space for
the backups. The backups of the changed data will be stored in the original partition of the data.
Unique Features
- 70 -
Chapter 5 Appendix
5-1 Configuring SATA Hard Drive(s)
To configure SATA hard drive(s), follow the steps below:
A.
B.
C.
D.
E.
Install SATA hard drive(s) in your computer.
Configure SATA controller mode in BIOS Setup.
Configure a RAID array in RAID BIOS. (Note 1)
Make a floppy disk containing the SATA RAID/AHCI driver for Windows XP. (Note 2)
Install the SATA RAID/AHCI driver (Note 2) and operating system.
Before you begin
Please prepare:
• At least two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard
drives with identical model and capacity). If you do not want to create RAID, you may prepare only one
hard drive.
• An empty formatted floppy disk.
• Windows Vista/XP setup disk.
• Motherboard driver disk.
5-1-1 Configuring AMD SB710 SATA Controller
A. Installing SATA hard drive(s) in your computer
Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available
SATA port on the motherboard. If there is more than one SATA controller on your motherboard, refer to
"Chapter 1," "Hardware Installation," to identify the SATA controller for the SATA port. (For example, on this
motherboard, the SATA2_0~SATA2_5 ports are supported by the AMD SB710 South Bridge.) Then connect
the power connector from your power supply to the hard drive.
(Note 1) Skip this step if you do not want to create RAID array on the SATA controller.
(Note 2) Required when the SATA controller is set to AHCI or RAID mode.
- 71 -
Appendix
B. Configuring SATA controller mode in BIOS Setup
Make sure to configure the SATA controller mode correctly in system BIOS Setup.
Step 1:
Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-Test).
Ensure OnChip SATA Controller is enabled under Integrated Peripherals. To enable RAID for the
SATA2_0/1/2/3 connectors, set OnChip SATA Type to RAID. To enable RAID for the SATA2_4/5 connectors,
set OnChip SATA Type to RAID and set OnChip SATA Port4/5 Type to As SATA Type (Figure 1).
CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
Integrated Peripherals
}
x
OnChip SATA Controller
OnChip SATA Type
OnChip SATA Port4/5 Type
Onboard LAN Function
Onboard LAN Boot ROM
SMART LAN Onboard Audio Function
Onboard 1394 Function
Onboard USB 3.0 Controller
Onchip USB Controller
USB EHCI Controllers
USB Keyboard Support
USB Mouse Support
Legacy USB storage detect
Onboard Serial Port 1
Onboard Parallel Port
Parallel Port Mode
ECP Mode Use DMA
Enter: Select
: Move
F5: Previous Values
[Enabled]
[RAID]
[As SATA Type]
[Enabled]
[Disabled]
[Press Enter]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Disabled]
[Enalbed]
[3F8/IRQ4]
[378/IRQ7]
[SPP]
3
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
Item Help
Menu Level 
ESC: Exit
F1: General Help
F7: Optimized Defaults
Figure 1
Step 2:
Save changes and exit BIOS Setup.
The BIOS Setup menus described in this section may differ from the exact settings for your motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you
have and the BIOS version.
Appendix
- 72 -
C. Configuring RAID set in RAID BIOS
Enter the RAID BIOS setup utility to configure a RAID array. Skip this step and proceed with the installation of
Windows operating system for a non-RAID configuration.
Step 1:
After the POST memory test begins and before the operating system boot begins, look for a message which
says "Press <Ctrl-F> to enter FastBuild (tm) Utility" (Figure 2). Press <Ctrl> + <F> to enter the RAID BIOS
setup utility.
RAID Option ROM Version 3.0.1540.49
(c) 2008 Advanced Micro Devices, Inc. All rights reserved.
No Array is defined..
Press <Ctrl-F> to enter FastBuild (tm) Utility...
Figure 2
Step 2:
Main Menu
This is the first option screen when you enter the BIOS RAID Setup utility. (Figure 3).
To view the disk drives assigned to arrays, press <1> to enter the View Drive Assignments window.
To create an array, press <2> to enter the Define LD window.
To delete an array, press <3> to enter the Delete LD window.
To view controller settings, press <4> to enter the Controller Configuration window.
Option ROM Utility (c) 2009 Advanced Micro Devices, Inc.
[ Main Menu ]
View Drive Assignments...........................[ 1 ]
Define LD..................................................[ 2 ]
Delete LD.................................................. [ 3 ]
Controller Configuration............................[ 4 ]
[ Keys Available ]
Press 1..4 to Select Option
[ESC] Exit
Figure 3
- 73 -
Appendix
Create Arrays Manually
To create a new array, press <2> to enter the Define LD Menu window (Figure 4). The Define LD selection
from the Main Menu allows users to begin the process of manually defining the drive elements and RAID
levels for one or multiple disk arrays.
Option ROM Utility (c) 2009 Advanced Micro Devices, Inc.
[ Define LD Menu ]
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
No RAID Mode
1
----
2
----
3
----
4
----
5
----
6
----
7
----
8
----
9
----
10
----
Total Drv
----
----
----
----
----
----
----
----
----
----
Capacity (GB)
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
Status
-------------------------------
[ Keys Available ]
[h] Up [i] Down
[ESC] Exit
[Enter] Select
Figure 4
In Figure 4, use the up or down arrow key to move to a logical disk set and press <Enter> to enter the RAID
configuration menu (Figure 5).
Option ROM Utility (c) 2009 Advanced Micro Devices, Inc.
LD
No
LD
1
[ Define LD Menu ]
Total Drv
RAID Mode
RAID 0
0
Stripe Block: 64 KB
Gigabyte Boundary: ON
Fast Init:
Cache Mode:
ON
WriteThru
[ Drives Assignments ]
Channel:ID Drive Model
1:Mas WDC WD800JD-22LSA0
2:Mas WDC WD800JD-22LSA0
Capabilities
SATA 3G
SATA 3G
Capacity (GB)
79.89
80.02
KeysAvailable
Available]]
[[Keys
[h] Up
[i] Down
[ESC] Exit
[Space] Change
[Ctrl-Y] Save
Figure 5
Appendix
- 74 -
[PgUp/Dn] Page Change
Assignment
N
N
In the following procedure, we'll create RAID 0 as an example.
1. Under the RAID Mode section, press the <SPACE> key to select RAID 0.
2. Set the Stripe Block size. 64 KB is the default.
3. Under the Drives Assignments section, press the up or down arrow key to highlight a drive.
4. Press the <SPACE> key or <Y>to change the Assignment option to Y. This action adds the drive to the
disk array. The Total Drv section will show the number of disks assigned.
5. Press <Ctrl>+<Y> keys to save the information. The window below will appear.
Fast Initialization option has been selected
It will erase the MBR data of the disk.
<Press Ctrl-Y key if you are sure to erase it>
<Press any other key to ignore this option>
Figure 6
6. Press <Ctrl>+<Y> to clear the MBR or press other keys to ignore this option. Then, the window below
will appear.
Press Ctrl-Y to Modify Array Capacity or press any
other key to use maximum capacity...
Figure 7
7. Press <Ctrl>+<Y> to set the capacity of the RAID array or press other keys to set the array to its maximum capacity.
8. After the creation is complete, the screen will return to Define LD Menu where you will see the newlycreated array.
9. Press <Esc> to return to Main Menu and press <Esc> again if you want to exit the RAID BIOS utility.
View Drive Assignments
The View Drive Assignments option in the Main Menu displays whether the attached hard drives are assigned to a disk array or are unassigned. Under the Assignment column, drives are labeled with their assigned disk array or shown as Free if unassigned.
Option ROM Utility (c) 2009 Advanced Micro Devices, Inc.
[ View Drives Assignments ]
Channel:ID Drive Model
Capabilities
1:Mas WDC WD800JD-22LSA0
SATA 3G
Extent 1 2:Mas WDC WD800JD-22LSA0
SATA 3G Extent 1 Capacity (GB)
79.89
79.82
80.2
80.02
Assignment
LD
1-1
LD
1-2
[ Keys Available ]
[h] Up
[i] Down
[ESC] Exit
[Ctrl+H] Secure Erase
[PgUp/Dn] Page Change
Figure 8
- 75 -
Appendix
Delete an Array
The Delete Array menu option allows for deletion of disk array assignments.
Deleting an existing disk array could result in loss of data. Record all array information including the
array type, the disk members, and stripe block size in case you wish to undo a deletion.
1. To delete an array, press <3> in the Main Menu to enter the Delete LD Menu. Then highlight the array you
wish to delete and press the <Delete> key or the <Alt>+<D> keys.
2. The View LD Definition Menu will appear (as shown in Figure 9) showing which drives are assigned to
this array. Press <Ctrl>+<Y> if you are sure to delete the array or other keys to abort.
3. When the array is deleted, the screen will return to Delete LD Menu. Press <Esc>to return to Main Menu.
Option ROM Utility (c) 2009 Advanced Micro Devices, Inc.
LD No
LD 1
RAID Mode
RAID 0
[ View LD Definition Menu ]
Total Drv Capacity (GB) Status
Functional
2
157.99
Stripe Block: 64KB
Cache Mode: WriteThru
[ Drives Assignments ]
Channel:ID
1:Mas 2:Mas Drive Model WDC WD800JD-22LSA0
WDC WD800JD-22LSA0
Capabilities
SATA 3G
SATA 3G
Press Ctrl-Y to delete the data in the disk!
or press any other
key to
abort... ]]
Keys
Available
[[Keys
Available
Figure 9
Appendix
- 76 -
Capacity (GB)
79.89
80.02
5-1-2 Making a SATA RAID/AHCI Driver Diskette
(Required for AHCI and RAID Mode)
To successfully install operating system onto SATA hard drive(s) that is/are configured to RAID/AHCI mode,
you need to install the SATA controller driver during the OS installation. Without the driver, the hard drive may
not be recognized during the Windows setup process. First of all, copy the driver for the SATA controller from
the motherboard driver disk to a floppy disk. For installing Windows Vista, you also can copy the SATA controller driver from the motherboard driver disk to a USB flash drive. See the instructions below about how to
copy the driver in MS-DOS and Windows mode.
In MS-DOS mode:
Prepare a startup disk that has CD-ROM support and a blank formatted floppy disk.
Steps:
1: Boot from the startup disk.
2: Remove the startup disk and insert the prepared floppy disk and the motherboard driver disk (here we assume that the drive letter for your optical drive is D:\).
3: At the A:\> prompt, type the following command. Press <Enter> after the command:
For the AMD SB710, type (Figure 1): (Note)
A:\>copy d:\bootdrv\SB7xx\x86\*.*
Figure 1
(Note)
Type the driver directory based on the operating system to be installed. Refer to the following table for the SATA driver directories for different Windows operating systems.
Operating System
Windows XP 32-bit
Windows XP 64-bit
Windows Vista 32-bit
Windows Vista 64-bit
Windows 7 32-bit (AHCI mode)
Windows 7 32-bit (RAID mode)
Windows 7 64-bit (AHCI mode)
Windows 7 64-bit (RAID mode)
Directory
Bootdrv\SB7xx\x86
Bootdrv\SB7xx\x64
Bootdrv\SB7xxV\LH
Bootdrv\SB7xxV\LH64A
Bootdrv\SB7xxW7\AHCI\x86
Bootdrv\SB7xxW7\RAID\x86
Bootdrv\SB7xxW7\AHCI\x64
Bootdrv\SB7xxW7\RAID\x64
- 77 -
Appendix
In Windows mode:
Steps:
1: Use an alternative system and insert the motherboard driver disk.
2: From your optical drive folder, double click the Menu.exe file in the BootDrv folder (Figure 2). A Command
Prompt window will open similar to that in Figure 3.
3: Insert the blank formatted disk. Depending on the operating system to be installed, select the controller
driver by pressing the corresponding letter from the menu and press <Enter>. For example, from the menu
in Figure 3, For the AMD SB710, select 3) SB7XX AHCI/RAID Driver for XP for Windows XP operating
system.
Your system will then automatically copy the driver files to the floppy disk. Press any key to exit when finished.
Figure 3
Figure 2
Appendix
- 78 -
5-1-3 Installing the SATA RAID/AHCI Driver and Operating System
With the SATA RAID/AHCI driver diskette and correct BIOS settings, you are ready to install Windows Vista/
XP onto your hard drive(s). The followings are examples of Windows XP and Vista installation.
A. Installing Windows XP
Step 1:
Restart your system to boot from the Windows XP setup disk and press <F6> as soon as you see the message "Press F6 if you need to install a 3rd party SCSI or RAID driver" (Figure 1). A screen will then appear
asking you to specify additional device.
Windows Setup
Press F6 if you need to install a third party SCSI or RAID driver.
Figure 1
Step 2:
Insert the floppy disk containing the SATA RAID/AHCI driver and press <S>. Then a controller menu similar
to Figure 2 below will appear. Select AMD AHCI Compatible RAID Controller-x86 platform and press
<Enter>.
Windows Setup
You have chosen to configure a SCSI Adapter for use with Windows, using a device support disk provided by an adapter manufacturer.
Select the SCSI Adapter you want from the following list, or press ESC to return to the previous screen.
AMD AHCI Compatible RAID Controller-x86 platform
AMD AHCI Compatible RAID Controller-x64 platform
ENTER=Select
F3=Exit
Figure 2
Step 3:
On the next screen, press <Enter> to continue the driver installation. After the driver installation, you can proceed with the Windows XP installation.
- 79 -
Appendix
B. Installing Windows Vista
(The procedure below assumes that only one RAID array exists in your system.)
Step 1:
Restart your system to boot from the Windows Vista setup disk and perform standard OS installation steps.
When a screen similar to that below appears (RAID hard drive will not be detected at this stage), select Load
Driver (Figure 3).
Figure 3
Step 2:
Insert the motherboard driver disk (Method A) or the removable storage device such as USB flash drive that
contains the SATA RAID/AHCI driver (Method B), then specify the location of the driver (Figure 4). Note: For
users using a SATA optical drive, be sure to copy the driver files from the motherboard driver disk to a USB
flash drive before installing Windows Vista (go to the BootDrv folder and save the whole SB7xxV folder to
the USB flash drive). Then use Method B to load the driver.
Method A:
Insert the motherboard driver disk into your system and browse to the following directory:
\BootDrv\SB7xxV\LH
For Windows Vista 64-bit, browse to the LH64A folder.
Method B:
Insert the USB flash drive containing the driver files and browse to the LH (for Windows Vista 32-bit) or
LH64A (for Windows Vista 64-bit) folder.
Figure 4
Appendix
- 80 -
Step 3:
When a screen as shown in Figure 5 appears, select AMD AHCI Compatible RAID Controller and click
Next.
Figure 5
Step 4:
After the driver is loaded, the RAID drive will appear. Select the RAID drive and then click Next to continue
the OS installation (Figure 6).
Figure 6
The install menus described in this chapter are for reference only and may differ by driver version.
- 81 -
Appendix
Rebuilding an Array:
Rebuilding is the process of restoring data to a hard drive from other drives in the array. Rebuilding applies
only to fault-tolerant arrays such as RAID 1 or RAID 10. To replace the old drive, make sure to use a new
drive of equal or greater capacity. The procedures below assume a new drive is added to replace a failed
drive to rebuild a RAID 1 array.
While in the operating system, make sure the chipset drivers and ATi RAID Utility have been installed from
the motherboard driver disk. Then launch the AMD RAIDXpert from All Programs in the Start Menu.
Step 1:
Enter the login ID and password (default: "admin"),
and then click Sign in to launch AMD RAIDXpert.
Step 2:
Select the RAID array to be rebuilt under Logical
Drive View and click the Rebuild tab in the Logical Drive Information pane.
Step 3:
Select one available drive and click Start Now to
start the rebuilding process.
Step 4:
The rebuilding progress is displayed on the
screen and you can select Pause/Resume/
Abort/Restart during the rebuilding process.
Step 5:
When done, the array's status on the Information page
in the Logical Drive Information pane will display as
Functional.
Appendix
- 82 -
5-2 Configuring Audio Input and Output
5-2-1 Configuring 2/4/5.1/7.1-Channel Audio
The motherboard provides six audio jacks on the
back panel which support 2/4/5.1/7.1-channel (Note)
audio. The picture to the right shows the default audio
Center/Subwoofer
Line In
Speaker Out
jack assignments.
Rear Speaker Out
Front Speaker Out
The integrated HD (High Definition) audio provides
Side
Mic In
Speaker Out
jack retasking capability that allows the user to change
the function for each jack through the audio driver.
For example, in a 4-channel audio configuration, if a Rear speaker is plugged into the default Center/Subwoofer speaker out jack, you can retask the Center/Subwoofer speaker out jack to be Rear speaker out.
• To install a microphone, connect your microphone to the Mic in jack and manually configure the
jack for microphone functionality.
• Audio signals will be present on both of the front and back panel audio connections simultaneously. If you want to mute the back panel audio (only supported when using an HD front panel
audio module), refer to instructions on the next page.
High Definition Audio (HD Audio)
HD Audio includes multiple high quality digital-to-analog converters (DACs) that support 44.1KHz/48KHz/
96KHz/192KHz sampling rate. HD Audio features multistreaming capabilities that allow multiple audio
streams (in and out) to be simultaneously processed. For example, users can listen to MP3 music, have an
Internet chat, make a telephone call over the Internet, and etc. all at the same time.
A. Configuring Speakers
(The following instructions use Windows Vista as the example operating system.)
Step 1:
After installing the audio driver, the HD Audio Manager
icon
will appear in the notification area. Double-click
the icon to access the HD Audio Manager.
(Note) 2/4/5.1/7.1-Channel Audio Configurations:
Refer to the following for multi-channel speaker configurations.
• 2-channel audio: Headphone or Line out.
• 4-channel audio: Front speaker out and Rear speaker out.
• 5.1-channel audio: Front speaker out, Rear speaker out, and Center/Subwoofer speaker out.
• 7.1-channel audio: Front speaker out, Rear speaker out, Center/Subwoofer speaker out, and Side speaker out.
- 83 -
Appendix
Step 2:
Connect an audio device to an audio jack. The The current connected device is dialog box appears. Select the
device according to the type of device you connect. Then
click OK.
Step 3:
On the Speakers screen, click the Speaker Configuration tab. In the Speaker Configuration list, select Stereo,
Quadraphonic, 5.1 Speaker, or 7.1 Speaker according to
the type of speaker configuration you wish to set up. Then
the speaker setup is completed.
B. Configuring Sound Effect
You may configure an audio environment on the Sound Effects tab.
C. Activating an AC'97 Front Panel Audio Module
If your chassis provides an AC'97 front panel audio module, to activate the AC'97 functionality, click the tool icon
on the Speaker Configuration tab. On the Connector
Settings dialog box, select the Disable front panel jack
detection check box. Click OK to complete.
D. Muting the Back Panel Audio (For HD Audio Only)
Click Device advanced settings on the top right corner
on the Speaker Configuration tab to open the Device
advanced settings dialog box. Select the Mute the rear
output device, when a front headphone plugged in
check box. Click OK to complete.
Appendix
- 84 -
5-2-2 Configuring S/PDIF In/Out
A. S/PDIF In
The S/PDIF In cable (optional) allows you to input digital audio signals to the computer for audio processing.
S/PDIF In Cable
Optical
S/PDIF In
Coaxial
S/PDIF In
1. Installing the S/PDIF In Cable:
Step 1:
First, attach the connector at the end of the cable
to the SPDIF_IN header on your motherboard.
Step 2:
Secure the metal bracket to the chassis back
panel with a screw.
2. Configuring S/PDIF In:
On the Digital Input screen, click the Default Format tab to select the default format. Click OK to complete.
(Note)
The actual locations of the S/PDIF In and S/PDIF Out connectors may differ by model.
- 85 -
Appendix
B. S/PDIF Out
The S/PDIF Out jacks can transmit audio signals to an external decoder for decoding to get the best audio
quality.
1. Connecting a S/PDIF Out Cable:
S/PDIF Coaxial Cable
S/PDIF Optical Cable
Connect a S/PDIF coaxial cable or a S/PDIF optical cable (either one) to an external decoder for transmitting
the S/PDIF digital audio signals.
2. Configuring S/PDIF Out:
On the Digital Output screen, click the Default Format tab and then select the sample rate and bit depth.
Click OK to complete.
Appendix
- 86 -
5-2-3 Configuring Microphone Recording
Step 1:
After installing the audio driver, the HD Audio Manager
icon
will appear in the notification area. Double-click
the icon to access the HD Audio Manager.
Step 2:
Connect your microphone to the Mic in jack (pink) on
the back panel or the Mic in jack (pink) on the front
panel. Then configure the jack for microphone functionality.
Note: The microphone functions on the front panel and
back panel cannot be used at the same time.
Step 3:
Go to the Microphone screen. Do not mute the recording volume, or you'll not be able to record the sound.
To hear the sound being recorded during the recording
process, do not mute the playback volume. It is recommended that you set the volumes at a middle level.
If you want to change the current sound input
default device to microphone, right-click on Microphone and select Set Default Device.
- 87 -
Appendix
Step 4:
To raise the recording and playback volume for the
microphone, click the Microphone Boost icon
on
the right of the Recording Volume slider and set the
Microphone Boost level.
Step 5:
After completing the settings above, click Start, point
to All Programs, point to Accessories, and then click
Sound Recorder to begin the sound recording.
* Enabling Stereo Mix
If the HD Audio Manager does not display the recording device you wish to use, refer to the steps below. The
following steps explain how to enable Stereo Mix (which may be needed when you want to record sound from
your computer).
Step 1:
Locate the Volume icon
in the notification area and
right-click on this icon. Select Recording Devices.
Step 2:
On the Recording tab, right-click on an empty space
and select Show Disabled Devices.
Appendix
- 88 -
Step 3:
When the Stereo Mix item appears, right-click on this
item and select Enable. Then set it as the default device.
Step 4:
Now you can access the HD Audio Manager to configure Stereo Mix and use Sound Recorder to record the
sound.
5-2-4 Using the Sound Recorder
A. Recording Sound
1.Make sure you have connected the sound input device (e.g. microphone) to the computer.
2.To record the audio, click the Start Recording button
.
3.To stop recording audio, click the Stop Recording button
.
Be sure to save the recorded audio file upon completion.
B. Playing the Recorded Sound
You can play your recording in a digital media player program that supports your audio file format.
- 89 -
Appendix
5-3 Troubleshooting
5-3-1 Frequently Asked Questions
To read more FAQs for your motherboard, please go to the Support&Downloads\Motherboard\FAQ page on
GIGABYTE's website.
Q: In the BIOS Setup program, why are some BIOS options missing?
A: Some advanced options are hidden in the BIOS Setup program. Press <Delete> to enter BIOS Setup during the POST. In
the Main Menu, press <Ctrl>+<F1> to show the advanced options.
Q: Why is the light of my keyboard/optical mouse still on after the computer shuts down?
A: Some motherboards provide a small amount of standby power after the computer shuts down and that's why the light is
still on.
Q: How do I clear the CMOS values?
A: For motherboards that have a CMOS_SW button, press this button to clear the CMOS values (before doing this, please
turn off the computer and unplug the power cord). For motherboards that have a clearing CMOS jumper, refer to the
instructions on the CLR_CMOS jumper in Chapter 1 to short the jumper to clear the CMOS values. If your board doesn't
have this jumper, refer to the instructions on the motherboard battery in Chapter 1. You can temporarily remove the battery from the battery holder to stop supplying power to the CMOS, which will clear the CMOS values after about one
minute.
Q: Why do I still get a weak sound even though I have turned my speaker to the maximum volume?
A: Make sure your speaker is equipped with an internal amplifier. If not, try a speaker with power/amplifier.
Q: Why cannot I install the onboard HD audio driver successfully? (For Windows XP only)
A: Step 1:First, make sure Service Pack 1 or Service Pack 2 has been installed (check in My Computer > Properties > General > System). If not, please update it from Microsoft's website. Then make sure the Microsoft UAA Bus Driver for
High Definition Audio has been installed successfully (check in My Computer > Properties > Hardware > Device
Manager > System Devices).
Step 2:Check if Audio Device on High Definition Audio Bus or Unknown device is present in Device Manager or
Sound, video, and game controllers. If yes, please disable this device. (If not, skip this step.)
Step 3:Then go back to My Computer > Properties > Hardware > Device Manager > System devices and right-click on
Microsoft UAA Bus Driver for High Definition Audio and select Disable and Uninstall.
Step 4:In Device Manager, right-click on the computer name and select Scan for hardware changes. When the Add
New Hardware Wizard appears, click Cancel. Then install the onboard HD audio driver from the motherboard
driver disk or download the audio driver from GIGABYTE's website to install.
For more details, go to the Support&Downloads\Motherboards\FAQ page on our website and search for "onboard HD
audio driver."
Q: What do the beeps emitted during the POST mean?
A: The following Award BIOS beep code descriptions may help you identify possible computer problems.
(For reference only.)
1 short: System boots successfully
1 long, 3 short: Keyboard error
2 short: CMOS setting error
1 long, 9 short: BIOS ROM error
1 long, 1 short: Memory or motherboard error
Continuous long beeps: Graphics card not inserted properly
1 long, 2 short: Monitor or graphics card error
Continuous short beeps: Power error
Appendix
- 90 -
5-3-2 Troubleshooting Procedure
If you encounter any troubles during system startup, follow the troubleshooting procedure below to solve the
problem.
START
Turn off the power. Remove all peripherals, connecting cables, and
power cord etc.
Make sure the motherboard does not short-circuit with the chassis or
other metal objects.
No
Yes
Isolate the short circuit.
The problem is verified and solved.
Check if the CPU cooler is attached to the CPU securely. Is the power connector of the CPU cooler connected to the CPU_FAN header
properly?
Yes
No
Secure the CPU cooler
on the CPU. Connect the
CPU cooler power cable
to the motherboard.
The problem is verified and solved.
Check if the memory is installed properly on the memory slot.
Yes
No
Correctly insert the
memory into the memory
socket.
The problem is verified and solved.
Insert the graphics card. Connect the ATX main power cable and the
12V power cable. Turn on the power to start the computer.
Make sure the graphics card is securely seated in the
expansion slot and power connectors are firmly attached.
A
(Continued...)
- 91 -
Appendix
A
When the computer is turned on, is the CPU cooler running?
Yes
No
The power supply, CPU or
CPU socket might fail.
The problem is verified and solved.
Check if there is display on your monitor.
Yes
No
The graphics card,
expansion slot, or monitor
might fail.
The problem is verified and solved.
Turn off the computer. Plug in the keyboard and mouse and restart
the computer.
Check if the keyboard is working properly.
Yes
No
The keyboard or keyboard
connector might fail.
The problem is verified and solved.
Press <Delete> to enter BIOS Setup. Select "Load Fail-Safe Defaults" (or "Load Optimized Defaults"). Select "Save & Exit Setup" to
save changes and exit BIOS Setup.
Turn off the computer and connect the IDE/SATA devices. Check if
the system can boot successfully.
Yes
No
The IDE/SATA device,
connector, or cable might
fail.
The problem is verified and solved.
Reinstall the operating system. Reinstall other devices one by one
(install one device at one time and then boot the system to see if the
device works successfully).
END
If the procedure above is unable to solve your problem, contact the place of purchase or local
dealer for help. Or go to the Support&Downloads\Technical Service Zone page to submit your
question. Our customer service staff will reply you as soon as possible.
Appendix
- 92 -
5-4 Regulatory Statements
Regulatory Notices
This document must not be copied without our written permission, and the contents there of must not be
imparted to a third party nor be used for any unauthorized purpose. Contravention will be prosecuted. We
believe that the information contained herein was accurate in all respects at the time of printing. GIGABYTE
cannot, however, assume any responsibility for errors or omissions in this text. Also note that the information in this document is subject to change without notice and should not be construed as a commitment by
GIGABYTE.
Our Commitment to Preserving the Environment
In addition to high-efficiency performance, all GIGABYTE motherboards fulfill European Union regulations
for RoHS (Restriction of Certain Hazardous Substances in Electrical and Electronic Equipment) and WEEE
(Waste Electrical and Electronic Equipment) environmental directives, as well as most major worldwide safety
requirements. To prevent releases of harmful substances into the environment and to maximize the use of
our natural resources, GIGABYTE provides the following information on how you can responsibly recycle or
reuse most of the materials in your "end of life" product.
Restriction of Hazardous Substances (RoHS) Directive Statement
GIGABYTE products have not intended to add and safe from hazardous substances (Cd, Pb, Hg, Cr+6,
PBDE and PBB). The parts and components have been carefully selected to meet RoHS requirement. Moreover, we at GIGABYTE are continuing our efforts to develop products that do not use internationally banned
toxic chemicals.
Waste Electrical & Electronic Equipment (WEEE) Directive Statement
GIGABYTE will fulfill the national laws as interpreted from the 2002/96/EC WEEE (Waste Electrical and Electronic Equipment) directive. The WEEE Directive specifies the treatment, collection, recycling and disposal of
electric and electronic devices and their components. Under the Directive, used equipment must be marked,
collected separately, and disposed of properly.
WEEE Symbol Statement
The symbol shown below is on the product or on its packaging, which indicates that this product
must not be disposed of with other waste. Instead, the device should be taken to the waste
collection centers for activation of the treatment, collection, recycling and disposal procedure.
The separate collection and recycling of your waste equipment at the time of disposal will help to
conserve natural resources and ensure that it is recycled in a manner that protects human health
and the environment. For more information about where you can drop off your waste equipment for recycling,
please contact your local government office, your household waste disposal service or where you purchased
the product for details of environmentally safe recycling.
w When your electrical or electronic equipment is no longer useful to you, "take it back" to your local or
regional waste collection administration for recycling.
w If you need further assistance in recycling, reusing in your "end of life" product, you may contact us at the
Customer Care number listed in your product's user's manual and we will be glad to help you with your
effort.
- 93 -
Appendix
Finally, we suggest that you practice other environmentally friendly actions by understanding and using the
energy-saving features of this product (where applicable), recycling the inner and outer packaging (including
shipping containers) this product was delivered in, and by disposing of or recycling used batteries properly.
With your help, we can reduce the amount of natural resources needed to produce electrical and electronic
equipment, minimize the use of landfills for the disposal of "end of life" products, and generally improve our
quality of life by ensuring that potentially hazardous substances are not released into the environment and
are disposed of properly.
China Restriction of Hazardous Substances Table
The following table is supplied in compliance with China's Restriction of Hazardous Substances (China
RoHS) requirements:
Appendix
- 94 -
- 95 -
Appendix
Appendix
- 96 -
- 97 -
Appendix
Appendix
- 98 -
Contact Us
• GIGA-BYTE TECHNOLOGY CO., LTD.
Address: No.6, Bau Chiang Road, Hsin-Tien,
Taipei 231, Taiwan
TEL: +886-2-8912-4000
FAX: +886-2-8912-4003
Tech. and Non-Tech. Support (Sales/Marketing) :
http://ggts.gigabyte.com.tw
WEB address (English): http://www.gigabyte.com.tw
WEB address (Chinese): http://www.gigabyte.tw
• G.B.T. INC. - U.S.A.
TEL: +1-626-854-9338
FAX: +1-626-854-9339
Tech. Support:
http://rma.gigabyte.us
Web address: http://www.gigabyte.us
• G.B.T. INC (USA) - Mexico
Tel: +1-626-854-9338 x 215 (Soporte de habla hispano)
FAX: +1-626-854-9339
Correo: soporte@gigabyte-usa.com
Tech. Support:
http://rma.gigabyte.us
Web address: http://latam.giga-byte.com
• Giga-Byte SINGAPORE PTE. LTD. - Singapore
WEB address : http://www.gigabyte.sg
• Thailand
WEB address : http://th.giga-byte.com
• Vietnam
WEB address : http://www.gigabyte.vn
• NINGBO G.B.T. TECH. TRADING CO., LTD. - China
WEB address : http://www.gigabyte.cn
Shanghai
TEL: +86-21-63410999
FAX: +86-21-63410100
Beijing
TEL: +86-10-62102838
FAX: +86-10-62102848
Wuhan
TEL: +86-27-87851061
FAX: +86-27-87851330
GuangZhou
TEL: +86-20-87540700
FAX: +86-20-87544306
Chengdu
TEL: +86-28-85236930
FAX: +86-28-85256822
Xian
TEL: +86-29-85531943
FAX: +86-29-85510930
Shenyang
TEL: +86-24-83992901
FAX: +86-24-83992909
• GIGABYTE TECHNOLOGY (INDIA) LIMITED - India
WEB address : http://www.gigabyte.in
• Saudi Arabia
WEB address : http://www.gigabyte.com.sa
• Gigabyte Technology Pty. Ltd. - Australia
WEB address : http://www.gigabyte.com.au
- 99 -
Appendix
• G.B.T. TECHNOLOGY TRADING GMBH - Germany
WEB address : http://www.gigabyte.de
• G.B.T. TECH. CO., LTD. - U.K.
WEB address : http://www.giga-byte.co.uk
• Giga-Byte Technology B.V. - The Netherlands
WEB address : http://www.giga-byte.nl
• GIGABYTE TECHNOLOGY FRANCE - France
WEB address : http://www.gigabyte.fr
• Sweden
WEB address : http://www.gigabyte.se
• Italy
WEB address : http://www.giga-byte.it
• Spain
WEB address : http://www.giga-byte.es
• Greece
WEB address : http://www.gigabyte.com.gr
• Czech Republic
WEB address : http://www.gigabyte.cz
• Hungary
WEB address : http://www.giga-byte.hu
• Turkey
WEB address : http://www.gigabyte.com.tr
• Russia
WEB address : http://www.gigabyte.ru
• Poland
WEB address : http://www.gigabyte.pl
• Ukraine
WEB address : http://www.gigabyte.ua
• Romania
WEB address : http://www.gigabyte.com.ro
• Serbia
WEB address : http://www.gigabyte.co.rs
• Kazakhstan
WEB address : http://www.gigabyte.kz
You may go to the GIGABYTE website, select your language
in the language list on the top right corner of the website.
• GIGABYTE Global Service System
To submit a technical or non-technical (Sales/Marketing) question, please link to:
http://ggts.gigabyte.com.tw
Then select your language to enter the system.
Appendix
- 100 -