Kingston Technology HyperX KHX2000C9AD3T1FK3/6GX 6GB 2000MHz

T E C H N O L O G Y
Memory Module Specification
KHX2000C9AD3T1FK3/6GX
6GB (2GB 256M x 64-Bit x 3 pcs.) DDR3-2000MHz
CL9 240-Pin DIMM Kit w/ Fan
DESCRIPTION:
Kingston's KHX2000C9AD3T1FK3/6GX is a kit of three 256M x 64-bit 2GB (2048MB) DDR3-2000MHz CL9 SDRAM
(Synchronous DRAM) memory modules, based on sixteen 128M x 8-bit DDR3 FBGA components per module. Each
module kit supports Intel ® XMP (Extreme Memory Profiles). Total kit capacity is 6GB. Each module kit has been tested
to run at DDR3-2000MHz at a low latency timing of 9-11-9 at 1.65V. The SPDs are programmed to JEDEC standard
latency DDR3-1333MHz timing of 9-9-9 at 1.5V. Each 240-pin DIMM uses gold contact fingers and requires +1.5V.
The JEDEC standard electrical and mechanical specifications are as follows:
This special kit part number includes Kingston's HyperX high-performance cooling fan assembly (KHX-FAN).
FEATURES:
JEDEC standard 1.5V ± 0.075V Power Supply
VDDQ = 1.5V ± 0.075V
667MHz fCK for 1333Mb/sec/pin
d
ye
Ke
8 independent internal bank
d
ye
Ke
d
Programmable CAS Latency: 5,6,7,8,9,10
ye
Ke
Posted CAS
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
Programmable CAS Write Latency(CWL) = 7(DDR3-1333)
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with tCCD = 4
which does not allow seamless read or write [either on the fly using A12 or MRS]
Bi-directional Differential Data Strobe
Internal(self) calibration : Internal self calibration through ZQ pin (RZQ : 240 ohm ± 1%)
On Die Termination using ODT pin
Average Refresh Period 7.8us at lower then TCASE 85°C, 3.9us at 85°C < TCASE . 95°C
Asynchronous Reset
PCB : Height 2.401” (61.00mm) w/ heatsink, double sided component
PERFORMANCE:
CL(IDD)
Row Cycle Time (tRCmin)
Refresh to Active/Refresh Command Time (tRFCmin)
Row Active Time (tRASmin)
Power
UL Rating
Operating Temperature
9 cycles
49.5ns (min.)
110ns
36ns (min.)
1.800 W (operating per module)
94 V - 0
0o C to 85o C
Storage Temperature
-55o C to +100o C
Document No. 4805507-001.A00
03/04/10
Page 1
Kingston
MODULE DIMENSIONS:
T E C H N O L O G Y
133.35
Units: millimeters
30.00
18.80
15.80
11.00
8.00
54.70
0.00
0.00
w/ heatsink assembly
mm
61 01
2.4
Document No. 4805507-001.A00
Page 2
Kingston
KHX-FAN
HyperX Cooling Fan Assembly
DESCRIPTION:
This document describes Kingston's HyperX memory module cooling fan assembly. If you are
looking to maximize the performance potential of your HyperX memory... this is it. With twin fans
focusing air directly onto your HyperX modules, your modules will run cooler, even in the most
demanding environments. The mechanical and electrical specifications are as follows:
PERFORMANCE:
Rated Voltage
Operational Voltage
Input Current
Input Power
RPM
Speed Control Type
Signal Output
12 VDC
8 - 13.5 VDC
0.09 amp
1.08 watt
3000 ± 10%
Max. Air Flow
0.43 m3/min
At Zero Static Pressure
15.02 CFM
Max. Air Pressure
2.31 mm-H2O
Frequency Generator (FG)
At Zero Flow
0.09 inch-H2O
Accoustical Noise
25 (28 max.) dB-A
HyperX Cooling Fan Assembly
Document No. 4805507-001.A00
Page 3
Kingston
T E C H N O L O G Y
Part Number: KHX-FAN
ASSEMBLY:
Document No. 4805507-001.A00
Page 4
Kingston
DIMENSIONS:
(Unit: Inches)
Document No. 4805507-001.A00
Page 5
Kingston
INSTALLATION:
Document No. 4805507-001.A00
Page 6
Kingston
INSTALLATION (cont.):
Document No. 4805507-001.A00
Page 7