High-end analogue and ISDN media and VPN gateway
The bintec RT4202 is a powerful and, thanks to its comprehensive equipment, flexible media and VPN gateway. With
its 19-inch metal housing and highly efficient internal switched-mode power supply the fan-free and hard drive-free
design guarantees long-term reliability in critical corporate applications.
Four configurable BRI interfaces (NT/TE) for the use of up to 8 ISDN B-channels, 4 analogue FXS interfaces and the
integrated 12-channel DSP permit twelve simultaneous hybrid voice connections (VoIP) and fax traffic (FoIP).
The device has five Gigabit Ethernet ports, which can be configured for LAN, WAN or DMZ, and comes with a licence
for 10 out of a possible 110 hardware-accelerated IPSec tunnels. This makes the RT4202 ideal for use as a media and
VPN gateway in SMEs and company head offices.
Remote CAPI
The remote CAPI is multiserver and multiside-capable.
Voice and fax applications can transfer data simultaneously on all eight available channels. Thanks to the dedicated
DSP hardware available for each channel, the entire system is not overburdened and the computing power remains
available for all routing and VPN tasks. The quality of each fax connection is therefore consistently high, irrespective of
the capacity utilisation of the rest of the system.
As the remote CAPI is a network application, which operates independently of the MS Windows© operating system
software, it is ideal for server use. Consequently, CAPI applications can be installed and maintained without suspending
operation and no reboot of the server is required. The software supports 16/32/64 Bit operating systems and
applications. The remote CAPI is also available for Linux.
This function is groundbreaking for the use of virtual machines. MS Hyper-V©, MS virtual PC©, VMware©, virtualBox©
and other virtual platforms do not offer an option to connect ISDN cards. The bintec remote CAPI avoids this problem
and
thereby allows fax and unified communication servers to be operated on virtual systems.
The following partners have already successfully certified our solution:
Servonic (IXI), Tobit (David), COM2 (TWINFAX), GFI (Faxmaker), ppedv(Visendo)
VoIP Media Gateway
With the RT4202 up to 12 telephone calls and fax transmissions (T.38) can be transferred simultaneously between the
IP network and the traditional telephone network. This can be carried out either directly as a terminal adapter (an ISDN
telephone is registered with the VoIP provider) or using a PBX.
A traditional ISDN PABX can be coupled with SIP providers or a modern IP PABX can be operated on the ISDN
BRI/PRI exchange connection. Fax transmission over T.38 is supported in both scenarios. A fax device on the
analogue connection of the traditional PABX can thus send and receive faxes over the SIP provider. This allows FoIP
clients and servers in the LAN to fax over the ISDN exchange.
The G.711, G.726 and G.729A voice coding offered by the SIP trunking and DDI-capable Funkwerk Media Gateway
can be adapted to suit your quality requirements and thereby ensure ISDN quality and high compression. Echoes are
successfully suppressed in G.168.
Fax over IP, T.38, permits implementation of the analogue T.30 group 3 fax protocol.
Thanks to the intelligent quality of service bandwidth management and adjustment, you can prioritise voice traffic over
normal data traffic over the internet, for example, and thereby always ensure sufficient bandwidth for your IP voice
connections.
Pure VoIP calls are not limited and are only restricted in terms of number by the existing bandwidth for the provider.
Media gateways are certified by:
Swyx with its Swyxware communication solution
Addix with its Asterisk Appliance Astimax
Routing and VPN gateway
The additional media services, which the bintec RT Series permits, in no way restrict the standard scope of functions of
the bintec R Series. You can use the entire scope of services of the VPN gateway with identical data rates in parallel to
media services.
Bintec gateways have features that go far beyond just IP routing and allow it to be seamlessly integrated into complex
IT infrastructures.
As routing protocols, you can use RIP, OSPF or the Multicast routing protocol PIM-SM for example, and the
comprehensive multicast support makes the device ideal for use in multimedia and streaming applications.
Even the basic equipment provides a SIP application level gateway (ALG) for the direct connection of IP telephones in
the network or for registering with a VoIP provider. The ALG automatically controls the internal firewall making it easier
to configure your VoIP solution, if the media gateway is not active.
You can prioritise voice traffic over normal data traffic using QoS support. If required you can give normal data traffic
priority over e-mail traffic.
The DNS proxy function supports the LAN for address implementation and the automated IP configuration of PCs is
carried out over an integrated DHCP server. The time server allows you to send the current time to all computers in the
LAN without having to query each computer on the internet.
The VPN IPSec solution works both with preshared keys as well as with certificates for authentication, which allows a
public key infrastructure to be created for maximum security.
Furthermore, the bintec IPSec implementation offers support when creating VPN connections with dynamic public IP
addresses. The exchange of IP addresses is carried out either over dynamic DNS providers or directly over ISDN.
IKE Config Mode and X-Auth (extended authentication) permit IPSec dialin solutions for multiple clients with minimal
costs and one-time password ensuring the highest level of security.
The professional functions are rounded off with bundling for parallel internet connections with load balancing and our
bintec Router Redundancy Protocol (BRRP).
VPN gateways are certified by Kobil with "Secure One Time Verification and Identification" (SecOVID) and Starface,
amongst others, which realise secure IP PABX connections over VPN with VoVPN.
Simple configuration and maintenance
The gateway is configured over the Funkwerk Configuration Interface (FCI), using the integrated configuration wizards
for example. The FCI is a web-based graphic user surface that you can use from any PC with an up-to-date Web
browser via an HTTP or encrypted HTTPS connection. It also offers the opportunity to manage the devices locally and
remotely over other configuration accesses such as Telnet, SSH and ISDN login.
DIME Manager from Funkwerk Enterprise Communications (FEC) is a free tool for managing FEC devices.
DIME Manager is aimed at administrators who manage networks with up to 50 devices. The software simplifies the
management and configuration of gateways or access points either individually or in logical groups.
When developing DIME Manager, simple and efficient operation was the primary aim. It allows, for example, software
updates to be applied to individual devices or groups of devices simply by drag and drop. DIME Manager recognises
and manages new devices in the network using SNMP multicasts, in other words independent of their current IP
address.
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RT4202
11.03.2011
Subject to technical
alterations
Remote CAPI / Fax Media Gateway
Feature
Description
Multiserver CAPI
A computer can use several CAPI server simultaneously
Multisite CAPI
Several computer can use the same BRI port
Access Control
Prevention by user passwort concept
ISDN server virtualising
Unlimited usage on virtual computers
Fax profile
Fax group 3
Number of parallel fax channels
8 fax channels
Maximum data rate
14,400 Baud
Fax standard
Fax protocol T.30
Protocols for fax data transmission
Fax data transmission according V.21, V.27, V.29, V.17
CAPI controller features
CAPI possibilities: Internal controller, supplementary services, DTMF (MFV), HOLD, ECT,
3PTY, CF, CD, MWI
B channel layer 1 protocols
64 kbps HDLC, 64 kbps bit transparent, V.110, T.30 fax G3, 56 kbps bit transparent
B channel layer 2 protocols
ISO 7776 (X.75 SLP), transparent, LAPD D-CH X.25 (SAPI 16), T.30 fax G3, PPP, V.120
asyn., V.120 Bit transparent, LAPD free SAPI
B channel layer 3 protocols
Transparent, T70/90NL, ISO 8208 (X.25 DTE-DTE), X25DCE, T.30 fax G3, T.30 fax G3
extended
Fax data compression standards
T.4 (MH-, MR compression), T.6 (MMR compression)
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RT4202
11.03.2011
Subject to technical
alterations
VoIP Media Gateway
Feature
Description
DSP support
VoIP and FoIP codecs are executed digital signal processors. Computation does not charge
the system and is dedicated reserved for each channel. Constant codec quality, independent
of system load, is guaranteed.
SIP user
No software limitation
SIP registrar
SIP users are able to sign on at the media gateway with registration and authentication.
SIP proxy
Mapping of an unlimited number of SIP single or DDI provider accounts to SIP single user or
to VoIP PABXs.
SIP ISDN gateway
Transparent conversion of connections of a VoIP PABX to ISDN trunk
ISDN SIP gateway
Transparent conversion of ISDN PABX connections to single SIP provider, or to DDI SIP trunk
access
SIP trunk
With 'SIP PBX Trunking' respectively SIP DDI Internet telephony has got all essential features
of ISDN. Especially Direct Dial In (DDI), which allows to assign single telephone numbers
(DDI numbers) to extensions and departments.
ISDN trunk
Support of two or more ISDN connections in point-to-point mode (BRI or PRI), which are
configuered as TE (collective line) or NT
SIP link
Switching of incoming and outgoing calls like SIP trunks, though without DDI, but with single
calling number blocks, with or without registerin
Call router
Flexible switching of all calls according rules; conditions for call forwarding (routing). List with
rules or rule chains for manipulating the signalled target calling number
CLID conversion
Manipulation of calling party numbers in incoming calls; add a prefix to incoming numbers, to
route corresponding calls via a certain SIP account.
Calling number transformation
Conversion list of calling numbers; in this list are correlated external and internal numbers.
Backup routes
Unlimited number of backup routes for the automatic selection of outside lines, (e.g. Prio 1 SIP
provider is not available, Prio 2 SIP provider returns line busy, call will be switched Prio 3 via
ISDN)
Number of simultaneous VoIP
connections
Number
of simultaneous hybrid
No software limitation
connections
Features
hybrid connections
Echo cancellation according G.168, Comfort Noise Generation CNG
DTMF support
Support of DTMF inband and out of band according standards RFC 2976 (SIP info) and RFC
2833 (RTP payload type/outband)
Audio Codec support
G.711, G.726 (16 kbps), G.726 (24 kbps), G.726 (32 kbps), G.726 (40 kbps), G.729
Audio Codec prioritisation
Selectable handshaking sequences, with priorization according quality, low or high bandwidth
Fax transmission
12 channels can be simultaneous converted from LAN fax T.38 to T.30, ISDN an analogue.
No matter how high the system load, for each channel is supported by a DSP.
Analogue terminal adapter
Imaging of analogue end devices to SIP, maximum of 4 simultaneous connections
Terminal adapter SIP ISDN
Imaging of ISDN end devices to SIP and imaging of SIP end devices to ISDN, maximum of 8
simultaneous connections
SIP protocols
UDP, TCP, TLS
SIP features
CLIP, CLIR. REFER, PRACK, SESSION timers, HOLD, MOH, INFO, NAPTR, ...
SIP RFCs
2327, 2976, 3261, 3262, 3263, 3264, 3311, 3323, 3325, 3428, 3515, 3581, 3608, 3891, 3966,
4028, 3555, 2833, 1035, 2782, 2915, 2617, ...
SIPS
SIP secure (TLS), establish secure calls
Media protocols
RTP, SRTP
Debug trace
Recording of all data streams via console and web configuration. Selectable trace formats:
text PCAP
12 ISDN SIP hybrid connections, independ of applied codecs by DSP HW support
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RT4202
11.03.2011
Subject to technical
alterations
ISDN Interface
Feature
Description
CAPI
CAPI 2.0 with CAPI user concept (password for CAPI use)
ISDN protocols
Euro-ISDN (Point-to-mulitpoint/Point-to-point)
ISDN auto-configuration
Automatic recognition and configuration of ISDN protocols
ISDN leased lines
Supported leased lines: D64S, D64S2, TS02, D64S2Y
B channel protocols
Excellent interoperability with other manufacturers (Raw HDLC, CISCO HDLC, X.75)
X.31 over CAPI
Support for various connection paths: X.31/A for ISDN D-channel, X.31/A+B for ISDN
B-channel, X.25 within ISDN B-channel (also leased lines)
Bit rate adaption
V.110 (1,200 up to 38,400 bps), V.120 up to 57,600 kbps (HSCSD) for connection to GSM
subscribers
VPN
Feature
Description
PPTP (PAC/PNS)
Point to Point Tunneling Protocol for establishing fo Virtual Privat Networks, inclusive strong
encryption methods with 128 Bit (MPPE) up to 168 Bit (DES/3DES, Blowfish)
PPP / PPTP hardware acceleration
Integrated hardware acceleration for PPP/PTPP encryption algorithms DES, 3DES, MPPE
GRE v.0
Generic Routing Encapsulation V.0 according RFC 2784 for common encapsulation
L2TP
Layer 2 tunnelling protocol inclusive PPP user authentication
Number of VPN tunnels
Inclusive 110 active PPTP, L2TP and GRE v.0 tunnels (also in combination possible)
IPSec
Internet Protocol Security establishing of VPN connections
Number of VPN tunnels
Inclusive 10 active VPN tunnels, optional up to 110 IPSec tunnels
IPSec Algorithms
DES (64 Bit), 3DES (192 Bit), AES (128,192,256 Bit), CAST (128 Bit), Blowfish (128-448 Bit),
Twofish (256 Bit); MD-5, SHA-1, RipeMD160, Tiger192 Hashes
IPSec hardware acceleration
Integrated hardware acceleration for IPSec encryption algorithms DES, 3DES, AES inclusive
hardware acceleration for MD-5, SHA-1 Hash generation
IPSec IKE
IPSec key exchange via preshared keys or certificates
IPSec IKE Config Mode
IKE Config Mode server enables dynamic assignment of IP addresses from the address pool
of the company. IKE Config Mode client enables the router, to get assigned dynamically an IP
address.
IPSec IKE XAUTH (Client/Server)
Internet Key Exchange protocol Extended Authenticaion client for login to XAUTH server and
XAUTH server for loging of XAUTH clients
IPSec IKE XAUTH (Client/Server)
Inclusive the forwarding to a RADIUS-OTP (One Time Password) server (supported OTP
solutions see www.funkwerk-ec.com).
IPSec NAT-T
Support of NAT-Traversal (Nat-T) for the application at VPN lines with NAT
IPSec IPComp
IPSec IPComp data compression for higher data throughput via LZS
IPSec certificates (PKI)
Support of X.509 multi-level certificates compatible to Micrososft and Open SSL CA server;
upload of PKCS#7/8/10/12 files via TFTP, HTTP, HTTP, LDAP, file upload and manual via FCI
IPSec SCEP
Certificates management via SCEP (Simple Certificate Enrollment Protocol)
IPSec Certificate Revocation Lists
(CRL)
IPSec Dead Peer Detection (DPD)
Support of remote CRLs on a server via LDAP or local CRLs
IPSec dynamic IP via ISDN
Transmission of dynamic IP address in ISDN D or B channel; free-of-charge licence necessary
IPSec dynamic DNS
Enables the registering of dynamic IP addresses by a dynamic DNS provider for establishing a
IPSec connection.
IPSec RADIUS
Authentication of IPSec connections at a RADIUS server. Additionally the IPSec peers, which
were configured on a RADIUS server, can be loaded into the gateway (RADIUS dialout).
IPSec Multi User
Enables the Dial-in of several IPSec clients via a single IPSec peer configuration entry
IPSec QoS
The possibility to operate Quality of Service (traffic shaping) inside of an IPSec tunnel
IPSec NAT
By activating of NAT on an IPSec connection it is possible, to implement several remote
locations with identical local IP addess networks in different IP nets for the VPN connection
IPSec throughput (1400)
86 Mbps with 1400 Byte packets with AES 256 / AES 128 / 3 DES encryption
IPSec throughput (256)
19 Mbps with 1400 Byte packets with AES 256 / AES 128 / 3 DES encryption
Continuous control of IPSec connection
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RT4202
11.03.2011
Subject to technical
alterations
Security
Feature
Description
NAT/PAT
Symmetric Network and Port Address Translation (NAT/PAT) with randomly generated ports
inclusive Multi NAT (1:1 translation of whole networks)
Policy based NAT/PAT
Network and Port Address Translation via different criteria like IP protocols, source/destination
IP Address, source/destination port
Policy based NAT/PAT
For incoming and outgoing connections and for each interface variable configurable
Content Filtering
Optional ISS/Cobion Content filter (30 day test license inclusive)
Stateful Inspection Firewall
Packet filtering depending on the direction with controling and interpretation of each single
connection status
Packet Filter
Filtering of IP packets according to different criteria like IP protocols, source/destination IP
address, source/destination port, TOS/DSCP, layer 2 priority for each interface variable
configurable
Routing
Feature
Description
Policy based Routing
Extended routing (Policy Based Routing) depending of diffent criteria like IP protocols
(Layer4), source/destination IP address, source/destination port, TOS/DSCP,
source/destination interface and destination interface status
Multicast IGMP
Support of Internet Group Management Protocol (IGMP v1, v2, v3) for the simultaneous
distribution of IP packets to several stations
Multicast IGMP Proxy
For easy forwarding of multicast packets via dedicated interfaces
Multicast Routing Protocol PIM SM
Protocol Independent Multicast (PIM) distributes information via a central Rendezvous Point
Server. PIM Modus Sparse Mode (SM) forwards only packets to groups which have been
requested
Multicast inside IPSec tunnel
Enables the transmission of multicast packets via an IPSec tunnel
RIP
Support of RIPv1 and RIPv2, separated configurable for each interface
Extended RIP
Triggerd RIP updates according RFC 2091 and 2453, Poisened Rerverse for a better
distribution of the routes; furthermore the possibility to define RIP filters for each interface.
OSPF
Support of the dynamic routing protocol OSPF
BGP4
On request
Routing throughput (1518)
199 Mbps with 1518 Byte packets
Routing throughput (256)
198 Mbps with 256 Byte packets
Protocols / Encapsulations
Feature
Description
PPP/MLPPP
Support of Point to Point Protocol (PPP) for establishing of standard PPP connections,
inclusive the Multilink extension MLPPP for the bundeling of several connections
PPPoE (Server/Client)
Point-to-Point Protocol over Ethernet (Client and Server) for establisching of PPP connections
via Ethernet/DSL (RFC 2516)
MLPPPoE (Server/Client)
Multilink extension MLPPPoE for bundeling several PPPoE connections (only if both sides
support MLPPPoE)
DNS
DNS client, DNS server, DNS relay and DNS proxy
DYN DNS
Enables the registering of dynamic assigned IP addresses at adynamic DNS provider, e.g. for
establishing of VPN connections
DNS Forwarding
Enables the forwarding of DNS requests of free configurable domains to assigned DNS
server.
DHCP
DHCP Client, Server, Proxy and Relay for siplified TCP/IP configuration
Packet size controling
Adaption of PMTU or automatic packet size controling via fragmentation
X.25 Enhanced
Optional: X.25 over ISDN, XOT, X.25 to TCP Gateway, X.25 PAD, TP0 Bridge
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RT4202
11.03.2011
Subject to technical
alterations
QoS
Feature
Description
Policy based Traffic Shapping
Dynamic bandwidth management via IP traffic shaping
Bandwidth reservation
Dynamic reservation of bandwidth, allocation of guaranteed and maximum bandwidths
DiffServ
Priority Queuing of packets on the basis of the DiffServ/TOS field
Layer2/3 tagging
Conversion of 802.1p layer 2 priorisation information to layer 3 diffserv attributes
TCP Download Rate Control
For reservation of bandwidth for VoIP connections
Redundancy / Loadbalancing
Feature
Description
BRRP
Bintec Router Redundancy Protocol for backup of several passive or active devices with free
selectable priority
BoD
Bandwidth on Demand: dynamic bandwidth to suit data traffic load
Load Balancing
Static and dynamic load balancing to several WAN connections on IP layer
VPN backup
Simple VPN backup via different media. Additional enables the Funkwerk interface based VPN
concept the application of routing protocols for VPN connections.
Layer 2 Functionality
Feature
Description
Bridging
Support of layer 2 bridging with the possibility of separation of network segment via the
configuration of bridge groups
VLAN
Support of up to 32 VLAN (Virtual LAN) for segmentation of the network in independent virtual
segments (workgroups)
Proxy ARP
Enables the router to answer ARP requests for hosts, which are accessible via the router. That
enables the remote clients to use an IP address from the local net.
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RT4202
11.03.2011
Subject to technical
alterations
Logging / Monitoring / Reporting
Feature
Description
Internal system logging
Syslog storage in RAM, display via web-based configuration user interface (http/https), filter
for subsystem, level, message
External system logging
Syslog, several syslog server with different syslog level configurable
E-Mail alert
Automatic E-Mail alert by definable events
SNMP traps
SNMP traps (v1, v2, v3) configurable
Activity Monitor
Sending of information to a PC on which Brickware is installed
IPSec monitoring
Display of IPSec tunnel and IPSec statistic; output via web-based configuration user interface
(http/https)
Interfaces monitoring
Statistic information of all pysical and logical interfaces (ETH0, ETH1, SSIDx, ...), output via
web-based configuration user interface (http/https)
ISDN monitoring
Display of active and past ISDN connections; output via web-based configuration user
interface (http/https)
IP accounting
Detailed IP accounting, source, destination, port, interface and packet/bytes counter,
transmission also via syslog protocol to syslog server
ISDN accounting
Detailed ongoing recording of ISDN connection parameter like calling number and charging
information, transmission also via syslog protocol to syslog server
RADIUS accounting
RADIUS accounting for PPP, PPTP, PPPoE and ISDN dialup connections
Keep Alive Monitoring
Control of hosts/connections via ICMP polling
Tracing
Detailed traces can be done for different protocols e.g. ISDN, PPPoE, ... generation local on
the device and remote via DIME manager
Tracing
Traces can be stored in PCAP format, so that import to different open source trace tools (e.g.
wireshark) is possible.
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RT4202
11.03.2011
Subject to technical
alterations
Administration / Management
Feature
Description
RADIUS
Central check of access authorization at one or several RADIUS server, RADIUS (PPP, IPSec
inclusive X-Auth and login authentication)
RADIUS dialout
On a RADIUS server configured PPP und IPSec connection can be loaded into the gateway
(RADIUS dialout).
TACACS+
Support of TACACS+ server for login authentication and for shell comando authorization
Time synchronization
The device system time can be obtained via ISDN and from a SNTP server (up to 3 time
server configurable). The obtained time can also be transmitted per SNTP to SNTP clients.
Automatic Time Settings
Time zone profiles are configurable. That enables an automatic change from summer to winter
time.
Supported management systems
DIME Manager, XAdmin
Configurable scheduler
Configuring of time and event controlled tasks, e.g. reboot device, activate/deactivate
interface, activate/deactivate WLAN, trigger SW update and configuration backup
Funkwerk Configuration Interface
(FCI)
Integrated web server for web-based configuration via HTTP or HTTPS (supporting self
created certificates). This user interface is by most of Funkwerk EC products identical.
Software update
Software updates are free of charge; update via local files, HTTP, TFTP or via direct access to
the FEC web server
Remote maintenance
Remote maintenance via telnet, SSL, SSH, HTTP, HTTPS and SNMP (V1,V2,V3)
Configuration via serial interface
Serial configuariton interface is available
ISDN remote maintenance
Remote maintenance via ISDN dial-in with checking of the calling number. The ISDN remote
maintenance connection between two funkwerk devices can be encrypted.
ISDN remote maintenance
A transparent mode enables transmissions of configurations and software updates
respectively
GSM remote maintenance
Remote maintenance via GSM login (external modem and cable required)
Device discovery function
Device discovery via SNMP multicast.
On The Fly configuration
No reboot after reconfiguration required
SNMP
SNMP (v1, v2, v3), USM model, VACM views, SNMP traps (v1, v2, v3) configurable, SNMP IP
access list configurable
SNMP configuration
Complete management with MIB-II, MIB 802.11, Enterprise MIB
Configuration export and import
Load and save configurations, optional encrypted; optional automatic control via scheduler
SSH login
Supports SSH V1.5 and SSH V2.0 for secure connections of terminal applications
HP OpenView
Integration into Network Node Manager
XAdmin
Support of XAdmin roll out and configuration managemant tool for larger router installations
(IP+ISDN+GSM)
Interfaces
Feature
Description
Ethernet
5 x 10/100/1000 Mbps Ethernet Twisted Pair, autosensing, Auto MDI/MDI-X, up to 4 ports can
be switches as additional WAN ports incl. load balancing, all Ethernet ports can be configured
as LAN or WAN.
Serial console
Serial console interface / COM port (mini USB): optional, connection of an analogue / GPRS
modem is possible (supported modems: see www.funkwerk-ec.com)
Analogue FXS
4 x FXS, internal
ISDN Basic Rate (BRI)
4 x BRI (NT/TE), each 2 B channel, internal/external
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RT4202
11.03.2011
Subject to technical
alterations
Hardware Features
Feature
Description
19 inch
Mountable in 19 inch rack, incl. 19 inch rack mount kit
Realtime clock
System time persists even at power failure for some hours.
Environment
Temperature range: Operational 0°C to 40°C; storage -10°C to 70°C; Max. rel. humidity 10 95% (non condensing)
Power supply
Integrated wide range power supply 110-240V, with energy efficient swiching controller
Power consumption
Max. 24 Watt, typ. 15 Watt
housing
19 inch 1 high unit metal case, screw-on 19 inch mounting-angle, LEDs and network
connectors at front side
Dimension
Ca. 485.6 mm x 220 mm x 45 mm (W x H x D)
Weight
Ca. 2600g
Fan
Fanless design therefor high MTBF
Reset button
Restart or reset to factory state possible
Content of Delivery
Feature
Description
Manual
Quick Installation Guide in German and English
DVD
DVD with system software, management software and documentation
Ethernet cable
1 Ethernet cable, 3m
Network cable
Power cable
Serial cable
Serial cable (mini USB - DSUB 9 female)
ISDN (BRI/S0) cable
ISDN (BRI/S0) cable, 3m
Service
Feature
Description
Warranty
2 year manufacturer warranty inclusive advanced replacement
Software Update
Free-of-charge software updates for system software (BOSS) and management software
(DIME manager)
Article number
Feature
Description
bintec RT4202; art. no. 5510000231
IP Access Media Gateway; 19 inch rack; 4x ISDN BRI; 4x FXS intern; 12x DSP; T.30/T.38 fax
support; incl. 10 IPSec tunnels (opt. max. 110), certificates, HW encryption; 4+1 Gigabit Eth.
switch; german and intern. version.
bintec RT4202 - UK; art. no.
5510000269
IP Access Media Gateway; 19 inch rack; 4x ISDN BRI; 4x FXS intern; 12x DSP; T.30/T.38 fax
support; incl. 10 IPSec tunnels (opt. max. 110), certificates, HW encryption; 4+1 Gigabit Eth.
switch; UK version.
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RT4202
11.03.2011
Subject to technical
alterations
Options
Feature
Description
VPN-IPSec-25
License for 25 additional activ IPSec tunnels; art. no. 5500000781
X.25
License for X.25 feature set; art. no. 5500000783
HotSpotHosting
Art.no. 5510000198 - HotSpot solution hosting fee for 1 year and 1 location; art.no.
5500000861 - HotSpot solution hosting fee for 2 year and 1 location; art.no. 5510000199 Additional location for HotSpot solution
Cobion Content Filter Small
License for one year Cobion content filter (small); art. no. 80551
MPPC and Stac compression
Free-of-charge license for Stac and MPPC compression; registration under
www.funkwerk-ec.com required
IP address ISDN B/D channel license
Free of charge license for IP address transmission in ISDN D or B channel for IPSec
connections; registering under www.funkwerk-ec.com required.
Service package 'large' (art.no.
5500000811)
Warranty extension of 3 years to a total of 5 years, including advanced replacement for FEC
products of the category "large". (Please find a ) detailed description as well as an overview of
the categories on www.funkwerk-ec.com/servicepackages.
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec RT4202
11.03.2011
Subject to technical
alterations