Multi-media port
Reset switch button
Power switch button
Power LED
HDD LED
5.25” mounting
bezel
5.25” to 3.5"
convertor
Fan controller
Patented tool-less 5.25”
device mounting
120mm fans
120mm fans
Patented tool-less
PCI add-on card holder
Rubberized
grommets
for liquid cooling
system’s tubing
Patented tool-less PSU
mounting bracket
Hardware list
(12)
Bracket(1)
for power supply mounting
PCI bracket (1)
(2)
Box(1)
for spare parts
Thumb screw(28)
for HDD
Shorter vision thumb screw(6)
for mother board mount
(4)
for PSU mounting
Longer vision thumb screw(3)
for mother board mount
USB3.0 to USB2.0
convertor (1)
SATA cable(2)
for HDD
Fan adjustable device
Side panels installation
L
Loose the screw and pull the
latch to release the side panel.
Remove the side panel.
H
Adding a lock to secure the
hardware.
3.5" Hard disk installation
Loose thumb screws to remove the
HDD cage.
Insert HDD, secured with thumb
screws.
I/O port installation
E-SATA
USB
USB3.0
USB
MIC EAR
HD AUDIO
BLUE 10
BLACK PUEPLE 8
YELLOW 6
BROWN 4
RED 2
4
5
1
9
Insert the HDD cage to the mounting
position.
Fasten the thumb screw to secure
the HDD cage.
PCI bracket installation
SATA
9
7
5
3
1
GREEN
KEY
ORANGE
N.C.
GND+H.S. TUBE
For access to rear I/O port.
USB3.0 to USB2.0 convertor
VCC
RED
D- WHITE
D+ GREEN
GND BLACK
RED
WHITE
GREEN
BLACK
KEY
VCC
DD+
GND
C50.X9000.00E-1
PCI Add-on card installation
!
1
!
!
Note:
For area where hard
to reach use the
longer thumb screw
2
Secure the stand-off on the M/B tray which match
with the M/B fix points, place the M/B on the
stand-off fasten with the thumb screws to secure.
Push the card into the PCI slot,
close the aluminum latch to secure
the card.
Open the aluminum latch to
remove the PCI slot bracket.
ODD installation
1. Remove the 5.25" to 3.5" converter.
2. Remove the 5.25" ODD
bezel.
3. Slide the 5.25" ODD bezel
downwards to remove it.
If you wish to use the
5.25" ODD bezel,
please adjust the metal
pin position on the
mounting bracket
5. Push the CD-ROM into the ODD cage
module, close the bracket to secure.
6. Reverse previous steps for installation
bezel & converter.
4. By pressing plastic
handle to release the
mounting bracket.
Adding the rubber pad to ODD's
eject bottom, when 5.25" ODD
bezel couldn't reach to the ODD.
PSU tray installation
Loosing four thumb screws to
remove the PSU mounting bracket.
Assembling the power supply with
PSU mounting bracket, and push
in gently.
Fasten four thumb screws onto the
case to secure.
PSU installation
Place the PSU on the stand, and
push again the rear panel.
Remove the HDD cage for long
PSU.
Vents for water cooling
Place the PSU bracket into
according slot as shown.
Lock the PSU bracket to secure the PSU.
* For transportation, please place screw
to secure the PSU
Place the water tube through
the rabber cover.
Removable upper double fan module
Loosing screws to remove fan
module.
Follow the arrow to remove the filter, press the
plastic clips to release the washable air filter.
C50.X9000.00E-2