Juniper CTP-SFP-1GE-SX network transceiver module

DATASHEET
CTP Series
Circuit to Packet
Platforms
Product Overview
Juniper Networks CTP Series Circuit to
Packet Platforms provide the advanced
technology and features required
to reliably transport time-division
multiplexing and other circuit-based
applications across next-generation IP/
MPLS networks. The CTP Series has the
field-proven flexibility, performance and
Product Description
With the ongoing deployment of IP networks, the efficiency and cost-savings gains of
IP are being realized for a variety of applications and functions. Largely left out of this
evolution have been the circuit-based applications such as time-division multiplexing
(TDM) leased line and voice private branch exchange (PBX) connections, serial encryption
connections, and analog and digital radio systems networking, because their synchronous
transport requirements are not addressed by a packet-based network. The Juniper
Networks® CTP Series Circuit to Packet Platforms enable customers to connect these
circuit-based applications easily and reliably across the IP network, bringing them the
advantages of converged multiservice IP networking.
reliability required for circuit applications.
The CTP Series includes the Juniper Networks CTP150, CTP2008, CTP2024, CTP2056
The CTP Series technology includes
Circuit to Packet Platforms, and the Juniper Networks CTPView Network Management
many advanced clocking options and
System. The products are designed for government agencies, enterprises and service
per-circuit buffers to enable end-to-
providers running circuit-based applications and range in size, port capacity and
end timing and the removal of jitter
redundancy options.
to create a psuedowire across the IP/
MPLS network. The CTP Series enables
customers to connect digital and analog
Product
Features
CTP150
The CTP150 Circuit to Packet Platform supports 4 to 8 interfaces of circuit emulation
traffic in a 1 RU rack mountable chassis. The 4-port interface options include T1/E1
and serial, and they interwork with any CTP Series product.
CTP2008
The CTP2008 Circuit to Packet Platform is a 1 RU rack mountable chassis that
supports up to 8 circuit emulation interfaces. The interface modules are software
configurable and are the same across the CTP2000 line.
CTP2024
The CTP2024 Circuit to Packet Platform is a 2 RU rack mountable chassis that
supports up to 24 circuit emulation interfaces. The chassis includes the option for
redundant power.
CTP2056
The CTP2056 Circuit to Packet Platform is a 4 RU rack mountable chassis that
supports up to 56 circuit emulation interfaces. The chassis includes the option for
redundant power.
CTPView
The CTPView Network Management System provides network operators with the
tools necessary to monitor network availability, report on IP networks performance,
provision circuits, and troubleshoot circuit issues through a web-based GUI.
voice applications easily and reliably
across the IP network using circuit
emulation over IP, bringing them the
advantages of converged multiservice
IP networking without the complexities
and cost of upgrades required for VoIP.
The CTP Series bridges the legacy and
IP world and provides many unique
features that enable cost reduction by
eliminating point-to-point circuits and
convergence of all applications onto one
IP/MPLS network.
1
Radio
EIA-530
RS-422
RS-232
Analog
RS-232
EIA-530
Diphase
Isochronous
CTP2008
Line Encryptor
TDM or PBX
M Series,
Fast
T Series, E Series
Ethernet
EIA-530
RS-422
DS-1
E-1
M Series,
T Series,
E Series
Radio
EIA-530
RS-422
RS-232
Host
Analog
RS-232
EIA-530
Diphase
Isochronous
M Series,
T Series,
E Series
CTP2008
Fast
Ethernet
M Series,
T Series,
E Series
CTP2008
Line Encryptor
MULTISERVICE
NETWORK
Satellite
modem
Fast
Ethernet
Network Management System
- Provisioning
- Troubleshooting
- Monitoring
- Performance Reports
EIA-530
RS-422
DS-1
E-1
TDM or PBX
Primary Circuit to Packet Solutions
Application
Application Description
Benefit
SS7 transport over IP
Provides transport of dedicated T1 or E1 SS7 links over the
IP/MPLS network.
Eliminates point-to-point T1 and E1 links required for
transporting SS7 traffic and allows convergence over the
IP/MPLS network.
TDM over IP solution
The provisioning of point-to-point TDM trunks over the IP
network does not require changes to the TDM equipment.
Allows the continued use and investment protection of the
existing TDM equipment or an easy transition path from a
TDM network to an IP network.
PBX interconnect
over IP solution
Provides T1, E1 and 4WE&M trunking for PBX
interconnection over the IP network.
Reduce WAN infrastructure cost through the elimination
of costly point-to-point circuits and leased lines required
to support TDM and/or ATM networks. Circuit emulation
over IP enables seamless transition to IP transport without
upgrading your entire infrastructure to VoIP.
PBX Extension over IP
with 2WFXS/2WFXO
Provides two-wire analog PBX to phone extensions over IP
and two-wire PBX to PBX/central office connections over IP.
Private-line automatic ringdown (PLAR) is also supported.
Reduces IT expenditures by enabling PBX tie lines to
be transported across less expensive IP data network
connections. Analog voice traffic is converted to IP,
eliminating the need for costly T1 tie lines.
Leased line extension
over IP solution
Supports standards-based encapsulation and DS0
bundling. IETF PWE3 RFCs, SAToP and CESoPSN are
supported.
Enables full, fractional and DS0 bundling and mapping of
T1 and E1 service provisioned over an IP/MPLS network and
enables interoperability between vendors.
Radio over IP solution
Allows for connectivity of analog and digital radios
over IP networks.
Provides a mechanism to deploy these systems over IP
networks while maintaining critical communications.
Serial encryption
over IP solution
Provides transport of KG/KIV bit-synchronous cipher text
across an IP network.
Eliminates the need to deploy TDM or ATM equipment—
saving cost, time, space, and power.
T1 and E1 backup over IP
Point-to-point T1 or E1 circuits can be automatically backed
up over the IP/MPLS network.
Eliminates redundant point-to-point circuit costs. The end
application does not need to detect IP, saving software and
hardware upgrade costs.
Features and Benefits
Key features and benefits of the CTP Series Circuit to Packet Platforms include the following.
Feature
Feature Description
Benefit
Software circuit
provisioning
EIA530, RS-232, V.35, 4WTO, T1, and E1 circuit types are
software configured including the line encoding, clocking,
rates, and IP settings.
The network quickly fulfills new and changing end user
requirements without deploying excess hardware.
Scalable product family
A family of four CTP Series Circuit to Packet Platforms
provides different port densities. Products can address the
requirements of small remote sites through large central
network hubs.
Network designers control costs by selecting the CTP Series
Circuit to Packet Platforms most suitable for the site when
considering circuit quantities and anticipated growth.
2
Features and Benefits (continued)
Feature
Feature Description
Benefit
CTPView Network
Management System
Secure, multi-user, web-based network management
system provides network monitoring, circuit provisioning,
IP performance reporting, database backup, and circuit
troubleshooting tools.
Managers quickly deploy circuits and services while
proactively monitoring the network. IP performance reports
provide detailed information on IP network jitter, delay and
packet loss. Circuit troubleshooting tools include integral
BERTS and loops to facilitate quick trouble resolution.
Multiple system and
circuit clocking solutions
CTP Series Circuit to Packet Platforms are designed to
use multiple external clocks as monitored and prioritized
system references. Circuits are configured to use the system
clock, external circuit timing, or to adaptively recover clock
information from the remote port when required by the
application or when no reference is configured.
Circuit reliability is improved since ports and systems
are configured with the clocking solution that is most
appropriate for the particular application.
Auto switch
The status of the CTP Series circuit ports is monitored, and
the circuit is automatically switched to an alternate local or
remote port when a failure is detected.
Network and circuit reliability are increased when the
circuits are automatically restored to alternate locations
and equipment in the event of an equipment, site or
network failure.
Packet protector
Redundant packets are created and transmitted to the IP
network and then processed by the receiving CTP Series.
Circuit quality and reliability are increased when IP
connections experience significant packet loss caused by
bit errors.
Autobaud
The input timing leads are monitored, and the circuit rate is
automatically changed at both ends of the network if a rate
change is detected.
Flexible rate agility enables immediate and automatic
provisioning changes.
Loops and BERTs
Each CTP Series port supports interface and network loops
and the ability to generate and monitor a bit error rate test
with up to nine BERT patterns selectable.
Support for standard circuit troubleshooting tools that are
built into the CTP Series help to quickly isolate network,
circuit or cable problems.
Layer 2 IP aggregation
The CTP Series Circuit to Packet Platforms can aggregate
layer 2 traffic from serial EIA530 interfaces onto a Fast
Ethernet or Gigabit Ethernet interface. Layer 2 protocols
supported are Frame Relay, PPP and Cisco-HDLC. Each CTP
Series port is connected to a different VLAN.
The ability to aggregate layer 2 traffic on the CTP Series
from multiple EIA530 serial interfaces reduces the router
interfaces needed for low-speed EIA530 IP aggregation.
Port mirroring
The CTP Series is able to port-mirror any transmit or any
receive up to 10 local or remote destinations.
Port mirroring minimizes the bandwidth required to send the
same traffic to multiple sites across the network. It enables
easy monitoring for troubleshooting circuit problems. Port
mirroring enables the replication of data to multiple local or
geographically dispersed locations.
Analog voice—4WE&M
The CTP Series supports analog 4WE&M type I, II,and V
interfaces with software selectable transmit and receivelevel adjustments per interface.
The ability to support analog 4WE&M interfaces allows the
CTP Series Circuit to Packet Platforms to offer another PBX
trunking option. The 4WE&M interface can also be used for
radio interfaces with push-to-talk requirements.
Analog voice—2WFXS
The CTP Series supports analog 2WFXS loop start, ground
start, and PLAR modes with software selectable transmit
and receive-level adjustments per interface.
The ability to support analog 2WFXS interfaces allows the
CTP Series Circuit to Packet Platforms to offer 2-wire voice
extensions over IP for remote phones, remote central office
or PBX equipment.
Analog voice—2WFXO
The CTP Series support analog 2WFXO loop start and
ground start modes with software selectable transmit and
receive-level adjustments per interface.
The ability to support analog 2WFXO interfaces allows the
CTP Series Circuit to Packet Platforms to offer 2-wire voice
extensions over IP to remote phones, or remote central
office or PBX equipment.
Voice compression
The CTP Series Voice Compression module supports 64k
G.711, 32k G.726, 16k G.726, 16k G.728, 8k G.729, and 2.4k
MELP compression algorithms. The voice compression
module also supports echo cancellation, silence suppression,
fax and modem detection, and companding conversion.
Voice compression can be applied on any T1 or E1 DS0
and on the analog 4WE&M interfaces. The use of voice
compression and silence suppression can dramatically
reduce the bandwidth required in the IP network. Multiple
DS0s or analog channels can be bundled into one packet to
further reduce the bandwidth required in the IP network.
IRIG-B
The CTP Series supports an inter-range instrumentation
group time code (IRIG-B) signal to be transported through
an IP network. IRIG-B encodes day of year, hour, minute, and
second data on a 1-KHz carrier frequency, with an update
rate of once per second.
Provides the ability to support IRIG-B transport over the IP
network with options to configure direction, output high and
low levels, and data range per interface.
3
Product Options
Option
Option Description
Applicable Products
T1/E1 interface module
8-port T1 and E1 interface module with standard RJ48 interfaces. IETF
PWE3 RFCs for SAToP and CESoPSN are supported.
CTP2008, CTP2024, CTP2056,
CTP150 (4-port only)
Serial interface module
8-port serial interface module is provided. Per-port software selectable
interfaces, data rates, clocking, etc. are available. Interface support for
EIA232, V.24, EIA530, EIA449, V.35, and X.21 is provided.
CTP2008, CTP2024, CTP2056,
CTP150 (4-port only)
Serial with T1/E1 interface
option
Provides additional software configurable T1 and E1 interface option
on the serial interface module. Full and fractional T1/E1 support is
also available.
CTP2008, CTP2024, CTP2056
Serial with Multiservice
interface option
Provides additional software configurable single channel 4-wire trunkonly interface option, IRIG-B option or high-quality analog option on the
serial interface module.
CTP2008, CTP2024, CTP2056, CTP150
(4-port serial and 2-port MS support only)
4WE&M analog module
8-port 4WE&M front module and rear transition module support type
I, II and V signaling options. The interface is a standard RJ21 amphenol
connector. One voice compression module is required in the CTP Series.
CTP2024, CTP2056
2WFXS analog module
24-port 2WFXS front module and rear transition module support loop
start, ground start and PLAR modes. The interface is a standard RJ21
amphenol connector. One voice compression module is required in the
CTP Series.
CTP2024, CTP2056
2WFXO analog module
12-port 2WFXO front module and rear transition module support
loop start and ground start modes. The interface is a standard RJ21
amphenol connector. One voice compression module is required in the
CTP Series.
CTP2024, CTP2056
Voice compression
module
The CTP Series Voice Compression module supports compression on
T1 and E1 DS0s and all analog voice bundles. The module supports
PCM, 32k G.726, 16k G.726, 16k G.728, 8k G.729, and 2.4k MELP
compression algorithms. The voice compression module also supports
echo cancellation, silence suppression, fax and modem detection, and
companding conversion between T1 and E1.
CTP2024, CTP2056
CTP clock main and
spoke modules
The CTP Series clock main and spoke modules are required when the
8-port serial module and compression module are installed into one
CTP Series device.
CTP2024, CTP2056
Gigabit Ethernet and Fast
Ethernet fiber SC modules
Provides for two 1000BASE-FX or 100BASE-FX SC connectors for IP
connectivity on the network side.
CTP2008, CTP2024, CTP2056
Gigabit Ethernet SFP fiber
options
SFP options include 1000BASE-T, 1000BASE-SX and 1000BASE-LX.
CTP2008, CTP2024, CTP2056
Y-cable
A cable connects one DTE to two DCE CTP Series serial ports to provide
1:1 hardware redundancy. This is only supported on serial interfaces.
This option is not available on T1 or E1 interfaces.
CTP2008, CTP2024, CTP2056, CTP150
AC power
Internal AC power supply is provided.
CTP2008, CTP2024, CTP2056, CTP150
DC power
Internal DC power supply is provided.
CTP2008, CTP2024, CTP2056
Redundant power
Provides for dual redundancy power supplies.
CTP2024, CTP2056
4
CTP150
CTP2008
CTP2024
CTP2056
Specifications
CTP150
CTP2008
CTP2024
CTP2056
17.25 x 1.75 x 14.5 in
(43.8 x 4.5 x 36.8 cm)
17.25 x 1.75 x 11.75 in
(43.8 x 4.5 x 29.8 cm)
17.25 x 3.5 x 11.75 in
(43.8 x 8.9 x 29.8 cm)
17.25 x 7.0 x 11.75 in
(43.8 x 17.8 x 29.8 cm)
Dimensions and Power
Dimensions (W x H x D)
Weight (lb)
14.5
12
20
27
Mounting
Front Rack
Front Rack
Front Rack
Front Rack
Input voltage (AC)
100-240 VAC
100-240 VAC
100-240 VAC
100-240 VAC
Input voltage (DC)
N/A
40-72 VDC
40-72 VDC
40-72 VDC
Power supply
100 W
250 W
250 W x 2
250 W x 2
Input current
1.5 A at 110 VAC
2 A at 110 VAC
2 A at 110 VAC
2.5 A at 110 VAC
Operating temperature
32° to 104° F
(0° to 40° C)
32° to 104° F
(0° to 40° C)
32° to 104° F
(0° to 40° C)
32° to 104° F
(0° to 40° C)
Humidity noncondensing
5 to 90%
5 to 90%
5 to 90%
5 to 90%
Yes
Yes
Yes
Yes
Serial Interfaces
Interfaces
EIA232, EIA530, EIA530A, V.35,
V.24, EIA449, X.21, T1, E1
IRIG-B
Yes
Yes
Yes
Yes
Encoding NRZ, Conditioned
Diphase, Isochronous,
Asynchronous, AMI, B8ZS, HDB3,
TDM/TDC, Transparent
Yes
Yes
Yes
Yes
Interface quantity
8
8
24
56
Rates
50 bps–12.880 Mbps
50 bps–12.880 Mbps
50 bps–12.880 Mbps
50 bps–12.880 Mbps
5
Specifications (continued)
CTP150
CTP2008
CTP2024
CTP2056
Analog voice 4-wire TO
interface quantity
4
8
24
56
4WE&M
N/A
N/A
16
48
2WFXS
N/A
N/A
48
144
2WFXO
N/A
N/A
24
72
Voice Interfaces
T1 and E1
8
8
24
56
Voice compression
N/A
N/A
Yes
Yes
Echo cancellation
N/A
N/A
Yes
Yes
Silence suppression
N/A
N/A
Yes
Yes
Fax and modem detection
N/A
N/A
Yes
Yes
Companding conversion
N/A
N/A
Yes
Yes
100BASE-T (RJ-45)
N/A
N/A
N/A
N/A
100/1000BASE-T (RJ-45)
2
2
2
2
100BASE-FX (SC)—Optional
N/A
2
2
2
1000BASE-FX (SC)—Optional
N/A
2
2
2
SFP 1000BASE-T
N/A
4
4
4
SFP 1000BASE-SX
N/A
4
4
4
SFP 1000BASE-LX
N/A
4
4
4
Precedent setting—(DSCP),
configurable TOS byte
Yes
Yes
Yes
Yes
VLAN tagging
Yes
Yes
Yes
Yes
Virtual IP
Yes
Yes
Yes
Yes
Circuit modes—symmetric,
asymmetric, unidirectional,
hairpin
Yes
Yes
Yes
Yes
IPv4 and IPv6
Yes
Yes
Yes
Yes
IETF PWE3 RFC SAToP
Yes
Yes
Yes
Yes
IETF PWE3 RFC CESoPSN
Yes
Yes
Yes
Yes
IP Interfaces
Layer 2 EIA530 aggregation
Yes
Yes
Yes
Yes
Port mirroring
Yes
Yes
Yes
Yes
Juniper Networks Services and Support
Juniper Networks is the leader in performance-enabling services and support, which are designed to accelerate, extend, and optimize
your high-performance network. Our services allow you to bring revenue-generating capabilities online faster so you can realize bigger
productivity gains and faster rollouts of new business models and ventures. At the same time, Juniper Networks ensures operational
excellence by optimizing your network to maintain required levels of performance, reliability, and availability. For more details, please visit
www.juniper.net/us/en/products-services.
6
Ordering Information
Model Number
Description
Model Number
Description
CTP2000 Line
CTP150
CTP150-AC
AC base chassis
Interface Modules
CTP150-IM-SER
4-port serial module with 4 HD-26 pin interfaces
and one clock input interface. Serial supports RS232/V.24, EIA530/530A/RS-422/499/X.21, V.35.
CTP2000-IM-8P-T1E1
8-port T1/E1 RJ48 interface module
CTP2000-IM-8P
8-port serial interface module—EIA530/V.11/RS422/X.21, RS-232/V.24, V.35
CTP2000-IM-8P-T1
8-port serial interface module—EIA530/V.11/RS422/X.21, RS-232/V.24, V.35, T1, E1
CTP150-IM-SER-MS
4-port serial module with 4 HD-26 pin interfaces
and one clock input interface. Includes two daughter
cards to add 4WTO analog, high- quality analog and
IRIG capabilities to two ports.
CTP2000-IM-8P-MS
CTP150-IM-T1E1
4-port T1/E1 module with 4 RJ48 interfaces and one
clock input interface.
8-port serial interface module—EIA530/V.11/RS422/X.21, RS-232/V.24, V.35, 4TWO, HQ Analog, IRIG
CTP2000-IM-4WEM
8-port 4WE&M analog voice module
CTP150-PWR-AC
Spare AC power supply
4WEM-RTM
8-port 4WE&M 8-port rear transition module
CTP150-CBL-DB15DCE-F
HD-26 interface cable, DB15, DCE, Female
CTP2000COMPRESSION
8-DSP voice compression and echo cancellation
module
CTP150-CBL-DB15DTE-M
HD-26 interface cable, DB15, DTE, Male
CTPCOMPRESSION-2
16-DSP voice compression and echo cancellation
module
CTP150-CBL-DB25DCE-F
HD-26 interface cable, DB25, DCE, Female
CTP2000-IM-2WFXS
24-port 2WFXS analog voice module
CTP150-CBL-DB25DCE-Y
Y-cable with DCE DB25 connectors
2WFXS-RTM
24-port 2WFXS rear transition module
CTP2000-IM-2WFXO
12-port 2WFXO analog voice module
2WFXO-RTM
12-port 2WFXO rear transition module
CTP150-CBL-DB25DTE-M
HD-26 Interface cable, DB25, DTE, Male
CTP150-CBL-RJ45DIU
HD-26 Interface cable, RJ45, V.24
Spares
CTP2000 Line
Base Units
CTP2000-PRC-S
Processor spare
CTP2000-RTC-S
Rear transition module spare
CTP2000-PWR-R
CTP2024/CTP2056 redundant power supply option
CTP2000-PWR-DC-R
CTP2024/CTP2026 redundant DC power supply
option
CTP2008-AC-02
CTP2008 AC base chassis
CTP2008-DC-02
CTP2008 DC base chassis
CTP2008-REC-RMK
CTP2008 recessed rack mount kit
CTP2024-AC-02
CTP2024 AC base chassis
CTP2024-REC-RMK
CTP2024 recessed rack mount kit
CTP2024-DC-02
CTP2024 DC base chassis
CTP2056-REC-RMK
CTP2056 recessed rack mount kit
CTP2056-AC-02
CTP2056 AC base chassis
CTP-CBL-4Q
CTP2056-DC-02
CTP2056 DC base chassis
Cable—100 pin to four (4) DB-25 DCE for
CTP2000 line
CTP-CBL-4Q-DTE
Cable—100 pin to four (4) DB-25 DTE for
CTP2000 line
CTP-CBL-4Q-Y
Redundancy cable for connections between two
CTP Series platforms
CTP-CLK-MAIN
Clock main rear transition module for CTP2000 line
CTP-CLK-SPOKE
Clock spoke rear transition module for CTP2000 line
Upgrades
CTP-FX2000GE-UPG
Dual SC multimode fiber Gigabit Ethernet PMC
upgrade
CTP-FX2000FE-UPG
Dual SC multimode fiber Fast Ethernet IM upgrade
CTP-Fiber-PMC
Fiber PMC card for CTP2000 line to support up to 2
SFP modules
CTP-SFP-1GE-T
Small form-factor pluggable 1000BASE-T Gigabit
Ethernet module (uses Cat 5 cable)
CTP-SFP-1GE-SX
Small form -factor pluggable 1000BASE-SX Gigabit
Ethernet optic module
CTP-SFP-1GE-LX
Small form-factor pluggable 1000BASE-LX Gigabit
Ethernet optic module
CTP2000-RAM-RTMUPG
CTP2000 line upgrade kit for release 6.0 includes
1G RAM, 4G CompactFlash card, and new Rear
Transition Module (RTM).
CTP2000-RAM-UPG
CTP2000 line upgrade kit for release 6.0 includes 1G
RAM and 4G CompactFlash card.
CTP Series Software
CTP-OS-4G
Current software on 4G CompactFlash card
CTP-CF-4G-S
4G CompactFlash spare, no CTPOS
CTPView Network Management System Hardware/Software
CTPVIEW-SVR-1
CTPView Network Management System server
hardware
CTPVIEW-SW
CTPView Network Management System software
7
About Juniper Networks
Juniper Networks is in the business of network innovation. From
devices to data centers, from consumers to cloud providers,
Juniper Networks delivers the software, silicon and systems that
transform the experience and economics of networking. The
company serves customers and partners worldwide. Additional
information can be found at www.juniper.net.
Corporate and Sales Headquarters
APAC Headquarters
EMEA Headquarters
To purchase Juniper Networks solutions,
Juniper Networks, Inc.
Juniper Networks (Hong Kong)
Juniper Networks Ireland
please contact your Juniper Networks
1194 North Mathilda Avenue
26/F, Cityplaza One
Airside Business Park
Sunnyvale, CA 94089 USA
1111 King’s Road
Swords, County Dublin, Ireland
representative at 1-866-298-6428 or
Phone: 888.JUNIPER (888.586.4737)
Taikoo Shing, Hong Kong
Phone: 35.31.8903.600
or 408.745.2000
Phone: 852.2332.3636
EMEA Sales: 00800.4586.4737
Fax: 408.745.2100
Fax: 852.2574.7803
Fax: 35.31.8903.601
www.juniper.net
Copyright 2011 Juniper Networks, Inc. All rights reserved. Juniper Networks, the Juniper Networks logo, Junos,
NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other
countries. All other trademarks, service marks, registered marks, or registered service marks are the property of
their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper
Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice.
1000139-004-EN June 2011
8
Printed on recycled paper
authorized reseller.