Save time, reduce costs and increase efficiency
Network-enables equipment for Internet access
Proactively monitors serial and Ethernet devices
Takes automatic action and/or troubleshooting
Automatically reporting with email or RSS
Fully Automate Your Remote Equipment with
Real-time Event Management and Reporting
IntelliBox®-I/O 2100 is a breakthrough in truly automated control of
remote equipment. Powered by Lantronix EventTrak™ technology,
this highly-advanced, programmable device server connects your
equipment to an IP network and monitors it to watch for events at
specified intervals. When an event occurs, IntelliBox automatically
sends pre-determined, user-defined command(s) to the equipment
causing it to take appropriate and/or corrective actions – without
any user intervention. IntelliBox can send email notification that
the event was detected and handled accordingly.
True Autonomous Control with EventTrak
IntelliBox proactively monitors and controls remote digital I/O, dry
contact (relay) and RS232/422/485-based equipment. With built-in
EventTrak technology, IntelliBox can be set to query an attached
device at timed intervals then, depending on the results, take prespecified action(s). In addition to monitoring a serial line the IntelliBox
can also monitor digital I/O. Fluid-level monitoring is a simple example –
if IntelliBox notices a digital float sensor drop to a ‘low level,’
it can trigger a relay to start the fluid pump. When the level is
restored the relay is triggered to stop the pump. IntelliBox sends
an email to the user notifying them of the situation and the
actions taken. Instead of reacting to an event or problem, users
are proactively notified that an event occurred and the appropriate
response automatically took place. This also enables users to control
networked equipment directly through the serial or I/O port rather
than depending on a PLC or SCADA server. In some instances, several
events should occur before action is taken. EventTrak allows “Chain
Definitions” (series of events/ actions) to be defined. They can be
saved, stored and transferred from one IntelliBox to another, providing
a great deal of flexibility for large-scale deployment.
IntelliBox is ideal for alarms, fluid pumps, motor drives, lights, fans,
phone systems, access/control/alarm panels, HVAC equipment, PLC’s,
projectors, security cameras, proximity readers, card readers, etc.
Automated Reporting
IntelliBox consolidates the task of monitoring/reporting on multiple
pieces of equipment. Rather than query and review the output of each
device separately, users can configure the IntelliBox to query attached
equipment at configurable intervals and gather the returned data.
Incoming data can be sent via email or RSS feed, allowing hundreds
of devices to be monitored from one RSS-enabled web page.
Incoming data can be scanned for specific information. When it is
detected, IntelliBox can send an email flagged as “Important” along
with the data and take corrective action if needed.
Enterprise-grade Security and
Data Center Standards
Equipped with the Lantronix Evolution OS™ networking operating system,
IntelliBox delivers enterprise-grade level networking security with built-in
SSH/SSL support. The hardened OS and mature protocol stack are
resilient to denial of service (DoS) and port mapping attacks and prevent
it from being used to bring down other networked devices. Evolution OS
uses familiar data-center standards such as a Cisco-like command line
interface (CLI) very similar to that used by routers and hubs, simplifying
configuration and enterprise network integration. It also incorporates
XML – a standard tool for web services, data transfer and rich content
management that encapsulates
data into a text-based format.
Powerful and Rugged
IntelliBox is equipped with isolated serial, I/O and Ethernet ports and
screw terminal connectors for serial, I/O, relay and power. It supports
Modbus TCP, Modbus ASCII and Modbus RTU and is FM-approved for
hazardous locations Class 1, Div. 2. IntelliBox also features 15KV serial
port ESD protection which protects the IntelliBox from electrical
overstress; ESD-protected I/O channels (independent and optically
isolated); wide -40°–75°C operational temperature range; and flexible
power with 9-30 VDC and 9-24 VAC input range.
IntelliBox can act as a Modbus TCP slave, enabling Modbus TCP
masters to monitor the status of digital inputs and set the digital
outputs and relays. It can also be used as a “Modbus bridge”
(Modbus TCP to Modbus RTU/ASCII protocol converter) enabling
users to connect RS232/RS485 Modbus RTU/ASCII devices to
their Ethernet network to be controlled by Modbus TCP
masters (PLCs, OPC servers, SCADA software, etc).
Device Server
Reduce service calls or trips to repair or check on equipment
IntelliBox does it for you!
IntelliBox-I/O 2100
IntelliBox 2100 Device Server
Device Server
IntelliBox-I/O 2100
Features and Specifications
Sample Application
Serial Interface
2 Serial ports: 1 RS232, 1 RS422/485 (4-wire/2-wire)
with terminal block connection
Baud rate selectable from 300 to 230 Kbps
Customizable baud rate support for non-standard
serial speeds
LED indicators for TXD and RXD activities
Serial Line Formats
Characters: 7 or 8 data bits
Stop bits: 1 or 2
Parity: odd, even, none
Flow Control
Hardware: RTS/CTS
Software: XON/XOFF
Modem Control
CTS, RTS, DTR, DCD on Serial 1
Digital I/O
2 Independently configurable digital I/Os, configured
via GUI set-up Menu
Opto-isolated to eliminate grounding issues
Logically compatible with 3.3V level and also higher
voltage levels
Transient voltage and polarity reversal protection built in
Relay
Contacts are capable of handling up to 8A resistive load
Contacts are mechanically isolated to eliminate
grounding issues
Contacts are non-latching with Normally Open (NO) or
Normally Closed (NC) for simple application such as power
failure indication
CPU
Lantronix DSTNI-EX 120 MHz clock, 256 KB SRAM, 16 KB Boot
ROM Internal CPU Memory
Memory
4 MB Flash
2 MB SRAM
Network Interface
1 RJ45 Ethernet port
10Base-T/100Base-TX
Full or half duplex
Auto-negotiating or hard coded
EEPROM
64 Kbits
Reset
Recessed push button
LED Indicators
10Base-T and 100Base-TX Link
Ethernet Activity
Serial Transmit Data
Serial Receive Data
Power / Status
Packaging
Case: metal enclosure with wall mounts
IP30 enclosure rating
Dimensions: (L x W x H): 115 x 109 x 23 mm (4.54 x 4.30 x .90 in), terminal blocks included
Weight: 0.3 kg (0.63 lb) (10 oz)
Management
Internal web server
SNMP v2C (MIB-II, RS232MIB)
Serial login
Telnet/SSH login
XML
DeviceInstaller software
Shipping Dimensions (L x W x H)
254 x 216 x 70 mm (10 x 8.5 x 2.75 in.)
Warranty
2-year limited warranty
Isolation
1.5 KVAC / 2.1 KVDC galvanic isolation between power input port and Ethernet port (except chassis ground)
1.5 KVAC / 2.1 KVDC galvanic isolation between power input port and serial ports
1.5 KVAC / 2.1 KVDC galvanic isolation between Ethernet port and serial ports
1.5 KVAC / 2.1 KVDC opto-isolation between digital I/O ports and all other ports
1.5 KVAC / 2.1 KVDC mechanical isolation between Relay contacts and all other ports
8 KV direct contact, 15 KV air discharge, ESD protection on all serial ports (IEC 1000-4-2, IEC 61000-4-2)
40 A (5/50 ns) EFT protection (IEC 61000-4-4), 12 A (8/20 us) lightning protection (IEC 61000-4-5) on Ethernet port
Transient voltage protection and ESD at power input with max non-repetitive surge current 800 A (8/20 us) (IEC 61000-4-2)
Transient voltage protection and ESD with max non-repetitive surge power 600W peak (10/1000 us) at digital I/O ports
Power
Removable screw terminal block connector
9-30 VDC or 9-24 VAC with chassis ground
2.3W
Environmental
Temperature: -40°C to 75°C (-40° to 167°F) Operating
Temperature: -40°C to 85°C (-40° to 185°F) Storage
Humidity: 10% to 90% relative humidity, noncondensing
Agency Approvals
UL, CSA, FCC, CE,TUV, CTick,VCCI, FM Class 1, Div. 2
Ordering Information
Protocols Supported
ARP, UDP/IP, TCP/IP, Telnet, ICMP, SNMP, DHCP, BOOTP, TFTP,
Auto IP, SMTP, FTP, DNS, Traceroute, HTTP
Part Number
Description
IBIO21002-01
IntelliBox-I/O 2100, 2 port IA device and I/O
server with EventTrak, worldwide power supply
with regional adapters.
Industrial Application Protocols
Modbus TCP, Modbus ASCII/RTU
15353 Barranca Parkway
|
Irvine
|
CA 92618
|
USA
|
Tel: 800.422.7055
|
Fax: 949.450.7232
|
www.lantronix.com
©2007, Lantronix, Inc. Lantronix and IntelliBox are registered trademarks, and DeviceLinx, EventTrak and Evolution OS are trademarks of Lantronix, Inc. All other trademarks are the property of their
respective owners. Specifications subject to change without notice. All rights reserved. 910-513 01/08 DGS2500