bintec W1002n
o WLAN according to IEEE 802.11n
o Dual-band radio module with 2.4 GHz and 5 GHz
o Physical data rates of up to 300 Mbps
o Compatible with IEEE 802.11agbh devices
o Operation as access point, bridge, WDS, client
o Integrated VPN router, providing up to 110 tunnels
simultaneously
o Distinct increase of data rates for LAN-to-LAN coupling
compared with conventional WLAN bridges
o PoE (Power over Ethernet) according to IEEE 802.3af
With the IEEE 802.11n compatibility mode, the W1002n offers compatibility with all previous IEEE 802.11g or IEEE
802.11abgh clients and supports the mixed operation of clients according to IEEE 802.11n and clients according to
IEEE 802.11b/g or IEEE 802.11a/h. This permits the trouble-free replacement of existing access points by the new
W1002n without the necessity of exchanging the previous clients. Clients already supporting 802.11n will automatically
benefit from the higher throughput and the better coverage of areas.
The operation of two W1002n devices in the bridge mode permits the setup of line-of-sight radio links. Here, again, the
benefits of the IEEE 802.11n technology can be used by transferring two separate data streams. The application of
dual polarization antennas permits easy installation. Dual polarization antennas consist of two antenna segments,
which are polarized orthogonally to each other. They, therefore, provide 2 cable connections. This means that the
W1002n transmits two separated partial streams from a to b, as defined by IEEE 802.11n. With this technology, more
than triple the data rates can be reached compared to the previous technology. At a distance of 1000 m, net data rates
of approximately 75 Mbps (TCP/IP) can be attained by using our dual polarization antennas.
The power supply is either performed by means of a highly efficient 230-V plug-in power supply or via PoE (Power over
Ethernet) according to Standard IEEE 802.3af. In the case of operation via PoE, it suffices to use a default PoE injector
or, for instance, a Funkwerk S128p switch with integrated PoE feeding. Expensive special PoE injectors are not
required for the W1002n.
For the application on the medical sector, the W1002n has been granted admission according to EN60601-1-2, like its
predecessor W1002. You can download the corresponding certificate in the download section, WLAN Products Conformity Declarations.
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec W1002n
07.09.2010
Subject to technical
alterations
Operating Modes
Feature
Description
WLAN disabled
In this operation mode the device is a powerful 2-port VPN router
WLAN access point
WLAN access point with VPN router functionalities
WLAN bridge
Point-to-point and point-to-multipoint mode (up to 8 links)
WLAN client
Transparent client for direct connection of Ethernet devices
Security
Feature
Description
Encryption WEP/WPA
WEP64 (40 Bit key), WEP128 (104 Bit key), WPA personal, WPA enterprise, WPA2 personal,
WPA2 enterprise
IEEE802.11i authentication and
encryption
802.1x/EAP-MD5, 802.1x/EAP-TLS, 802.1x/EAP-TTLS, 802.1x/EAP-PEAP, key management,
PSK/TKIP encryption, AES encryption, 802.1x/EAP
Access control list (ACL)
MAC address filter for WLAN clients
VLAN
Network segments on layer2 possible. Per SSID one VLAN ID available. Static VLAN
configuration according IEEE 802.1q; up to 32 VLANs supported.
Inter cell repeating
Inter traffic blocking for public hot spot (PHS) applications for preventing of communication
radio client to radio client in a single radio cell.
NAT/PAT
Network & Port Address Translation / Stateful Packet Inspection: Isolation of complete network
from public access
VPN - IPSec
10 tunnels inclusive, 100 more via separate license
VPN - IPSec
Powerful encryption up to 256 bits (AES, 3DES, DES, CAST, Blowfish, Twofish)
VPN - IPSec DPD
Dead Peer Detection for IPSec tunnels
VPN - PPTP
Integrated
VPN - PPTP
Strong encryption up to 128 bits (MPPE), up to 168 bits (DES/3DES, Blowfish)
DynDNS / DynVPN
Router can still be reached over the Internet in spite of dyn. IP address
IKE for IPSec
Pre-Shared Keys and X.509 certificate support
X.509
X.509 v1/v3 certificates (PKCS#7/8/10, 12, CLRs, SCEP)
QoS for IPSec
Available
PKI Support for IPSec
Available
NAT Traversal for IPSec
Available
IPCOMP
IP compression
IPSec / RADIUS
Available
IPSec redesign
Policy manager and interface concept
L2TP
Layer 2 tunnelling protocol for ATM, Ethernet, PPP; user authentication
GRE
V.0 according RFC 2784 for common encapsulation
Hardware encryption
3DES, AES and RC4
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec W1002n
07.09.2010
Subject to technical
alterations
Wireless LAN Features
Feature
Description
WLAN standards
802.11n (Mimo 2x3); 802.11b; 802.11g; 802.11a; 802.11h
Frequency bands 2.4 GHz
indoor/outdoor (EU)
2.4 GHz Indoor/Outdoor (2412-2472 MHz) max. 100 mW EiRP. This information is related to
the permitted transmission power in Germany. The permitted transmission power may vary in
other countries.
Frequency bands 5 GHz indoor (EU)
5 GHz indoor (5150-5350 MHz) max. 200 mW EiRP allowed. This information is related to the
permitted transmission power in Germany. The permitted transmission power may vary in
other countries.
Frequency bands 5 GHz outdoor (EU) 5 GHz outdoor (5470-5725 MHz) max. 1000 mW EiRP allowed. This information is related to
the permitted transmission power in Germany. The permitted transmission power may vary in
other countries.
Frequency bands 5.8 GHz BFWA
(Germany)
5.8 GHz BFWA (5755-5875 MHz) max. 4000 mW EiRP allowed. This information is related to
the permitted transmission power in Germany. For the usage in other countries, please
contact the location regulation authorities.
WLAN modes
2.4 GHz operation: 802.11b only; 802.11g only, 802.11b/g/n mixed; 802.11b/g/n mixed long;
802.11b/g/b mixed short; 802.11b/g/n; 802.11g/n; 802.11n only; 5 GHz Operation: 802.11a
only; 802.11a/n; 802.11n only
Automatic Rate Selection (ARS)
Available
Transmission rate
Automatic fallback or fixed transmission rate selectable
Data rates for 802.11b,g (2.4 GHz)
11, 5.5, 2 und 1 Mbps (DSSS modulation); 54, 48, 36, 24, 18, 12, 9 and 6 Mbps (OFDM
modulation)
Data rates for 802.11a,h (5 GHz)
54, 48, 36, 24, 18, 12, 9 and 6 Mbps (OFDM modulation)
Data rates for 802.11n (2.4 / 5 GHz)
MSC0-15 enables physical rates up to 150 Mbps at 20 MHz channels bandwidth, 2 streams,
short guard interval; MSC0-15 enables physical data rates up to 300 Mbps at 40 MHz
channels bandwidth, 2 streams, short guard interval
Receiver Sensitivity @ 2.4 GHz
802.11b/g
1 Mbps -91 dBm; 2 Mbps -90 dBm; 5.5 Mbps -89 dBm; 11 Mbps -88 dBm; 6 Mbps -90 dBm;9
Mbps -89 dBm; 12 Mbps -88 dBm; 18 Mbps -86 dBm; 24 Mbps -83 dBm; 36 Mbps -80 dBm;
48 Mbps -76 dBm; 54 Mbps -74 dBm
Receiver Sensitivity @ 2.4 GHz
802.11n 20 MHz
MSC0 -89 dBm; MSC1 -87 dBm; MCS2 -85 dBm; MCS3 -82 dBm; MCS4 -79 dBm; MSC5 -75
dBm; MCS6 -73 dBm; MCS7 -70 dBm; MCS8 -83 dBm; MCS9 -84 dBm; MCS10 -81 dBm;
MCS11 -79 dBm; MCS12 -80 dBm; MCS13 -72 dBm; MCS14 -68 dBm; MCS15 -67 dBm
Receiver Sensitivity @ 2.4 GHz
802.11n 40 MHz
MSC0 -87 dBm; MSC1 -84 dBm; MCS2 -82 dBm; MCS3 -79 dBm; MCS4 -75 dBm; MSC5 -71
dBm; MCS6 -69 dBm; MCS7 -67 dBm; MCS8 -86 dBm; MCS9 -83 dBm; MCS10 -79 dBm;
MCS11 -77 dBm; MCS12 -74 dBm; MCS13 -69 dBm; MCS14 -67 dBm; MCS15 -65 dBm
Receiver Sensitivity @ 5 GHz
802.11a/h
6 Mbps -88 dBm; 9 Mbps -87 dBm; 12 Mbps -86 dBm; 18 Mbps -84 dBm; 24 Mbps -82 dBm;
36 Mbps -78 dBm; 48 Mbps -74 dBm; 54 Mbps -73 dBm
Receiver Sensitivity @ 5 GHz
802.11n 20 MHz
MSC0 -88 dBm; MSC1 -85 dBm; MCS2 -83 dBm; MCS3 -81 dBm; MCS4 -78 dBm; MSC5 -74
dBm; MCS6 -72 dBm; MCS7 -70 dBm; MCS8 -88 dBm; MCS9 -85 dBm; MCS10 -83 dBm;
MCS11 -80 dBm; MCS12 -77 dBm; MCS13 -72 dBm; MCS14 -70 dBm; MCS15 -68 dBm
Receiver Sensitivity @ 2.4 GHz
802.11n 40 MHz
MSC0 -84 dBm; MSC1 -82 dBm; MCS2 -79 dBm; MCS3 -77 dBm; MCS4 -74 dBm; MSC5 -69
dBm; MCS6 -67 dBm; MCS7 -66 dBm; MCS8 -83 dBm; MCS9 -82 dBm; MCS10 -79 dBm;
MCS11 -76 dBm; MCS12 -72 dBm; MCS13 -68 dBm; MCS14 -66 dBm; MCS15 -64 dBm
Output power (without antenna gain)
Adjustable in following steps: 5, 8,11,14,16 und 17.5 dBm. Maximal power varies depending
on data rate and frequency band.
Tx Power @ 2.4 GHz 802.11b/g
1 Mbps 16 dBm; 2 Mbps 16 dBm; 5.5 Mbps 16 dBm; 11 Mbps 16 dBm; 6 Mbps 17,5 dBm; 9
Mbps 17,5 dBm; 12 Mbps 17 dBm; 18 Mbps 17 dBm; 24 Mbps 15 dBm; 36 Mbps 15 dBm; 48
Mbps 13 dBm; 54 Mbps 13 dBm
Tx Power @ 2.4 GHz 802.11n 20
MHz/40 MHz
MSC0 17.5 dBm; MSC1 17,5 dBm; MCS2 17 dBm; MCS3 17 dBm; MCS4 15 dBm; MSC5 15
dBm; MCS6 13 dBm; MCS7 13 dBm; MCS8 17.5 dBm; MCS9 17.5 dBm; MCS10 17 dBm;
MCS11 17 dBm; MCS12 15 dBm; MCS13 15 dBm; MCS14 13 dBm; MCS15 13 dBm
Tx Power @ 5 GHz 802.11b/g
1 Mbps 16 dBm; 2 Mbps 16 dBm; 5.5 Mbps 16 dBm; 11 Mbps 16 dBm; 6 Mbps 17.5 dBm; 9
Mbps 17.5 dBm; 12 Mbps 17 dBm; 18 Mbps 17 dBm; 24 Mbps 15 dBm; 36 Mbps 15 dBm; 48
Mbps 13 dBm; 54 Mbps 13 dBm
Tx Power @ 5 GHz 802.11n 20
MHz/40 MHz
MSC0 17.5 dBm; MSC1 17.5 dBm; MCS2 17 dBm; MCS3 17 dBm; MCS4 15 dBm; MSC5 15
dBm; MCS6 13 dBm; MCS7 13 dBm; MCS8 17.5 dBm; MCS9 17.5 dBm; MCS10 17 dBm;
MCS11 17 dBm; MCS12 15 dBm; MCS13 15 dBm; MCS14 13 dBm; MCS15 13 dBm
Number of spatial streams (802.11n)
1 or 2
Bandwidth (802.11n)
20/40 MHz (bundling of two adjoining 20 MHz channels to one 40 MHz channel)
Short guard interval (802.11n)
On/off switchable; increase of throughput by reduction of the guard intervals from 800ns to
400ns
DTIM Period
Adjustable
Multi SSID
Depending on the complexity of configuration up to 8 service sets per radio module, with
virtual access points and own MAC address per SSID.
Broadcast SSID
On/off switchable
Clients (Pwr. Managmt./max number)
Registering of up to 250 clients per radio module simultaneously in access point mode. Default
value is 32 clients.
Country-specific settings
Channel settings according regulatory domain (802.11d) permitted.
TPC
TPC (transmission power control): For 5 GHz, automatic reduction of transmission power
according EN301893
DFS
DFS (dynamic frequency selection): For 2.4 and 5 GHz, channels are dynamically used
depending on operating grade. DFS is implemented in bridge links master and slave.
RTS/CTS
RTS/CTS threshold adjustable
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec W1002n
07.09.2010
Subject to technical
alterations
Maintenance and Service
Feature
Description
Configuration a. maintenance: Device
configuration
Configuration via
a. maintenance: SNMP
Telnet, SSH, HTTP, HTTPS, SNMP
Configuration a. maintenance: SNMP
configuration
Configuration a. maintenance: SSH
Complete management with MIB-II, MIB 802.11, enterprise MIB
Login
Configuration a. maintenance:
HTTP/HTTPS
Web-based configuration (FCI). The user interface is identical with almost all Funkwerk
products.
SNMP (v1, v2, v3), USM model, VACM views, SNMP traps (v1, v2, v3) configurable, SNMP IP
access list configurable
Supports SSH V1.5 and SSH V2.0, for secure connections of terminal applications
Configuration a. maintenance: Secure SSH available, HTTPS, Telnet protected against 'bruce force attacks'
configuration
Configuration a. maintenance:
Load and save of configurations; save configuration optionally encrypted; optional, automatic
Configuration export and import
controlled via scheduler
Configuration a. maintenance: On the
fly
configuration
Configuration
a. maintenance:
No restart is required after the configuration has been changed.
Software update
Software updates free of charge; loadable via file, HTTP or via direct access to the FEC
server; optional, automatic controlled via scheduler
External reporting: Syslog
Syslog client, with different levels of messaging.
External reporting: eMail alert
Automatic eMail alert by definable events
External reporting: SNMP traps
Supported
External reporting: Activity monitor
Sending of information to a PC on which Brickware is installed
Monitoring: Internal Log
Output via web-based configuration interface (http/https), filter: subsystem, level, message
Monitoring: IPSec
Displayed: IPSec tunnels and IPSec statistics; output via web-based configuration interface
(http/https)
Monitoring: Interfaces
Statistic information of all physical and logical interfaces (ETH0, ETH1, SSIDx, ...)
Monitoring: WLAN
Detailed displays for radio, VSS, WDS link, bridge links, client links. Displayed are per link:
MAC address, IP address, TX packets, RX packets, signal strength for every receiving aerial,
signal-to-noise ratio, data rate
Monitoring: Configurable scheduler
Following events can be scheduled: Reboot device, activate/deactivate interface,
activate/deactivate WLAN, initiate 5 GHz band scan, trigger SW update, trigger configuration
backup
Management: Supported
management
Management:systems
Discovery function
WiLMA, DIME manager, XAdmin
Documentation
German and English documentation on CD and in the Internet for download
Guarantee
2-year manufacturer's guarantee, Online RMA handling
Protocols: Madge Discovery Protocol (MDP), Funkwerk discovery protocol (ADP), works also
across subnets
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec W1002n
07.09.2010
Subject to technical
alterations
Software Features
Feature
Description
Roaming (access point mode)
Seamless roaming with IAPP (artem Inter Access Point Protocol)
Fast roaming 802.1x (access point
mode)
Roaming behaviour (client mode)
Pre authentication and PMK caching allows fast roaming by 802.1x encryption
WDS
Wireless Distribution System: Include high security TKIP and AES, interoperable with other
devices from the Funkwerk-EC portfolio (not bintec W500)
Bridge: point-to-point /
point-to-multipoint
Point-to-point connection between two access points, point-to-multipoint connection between
up to eight partners access points
Bridge
Full remote configuration: Protocol with encrypted transmission. RTS/CTS threshold
adjustable. Operating channels: According to the regulatory domain. Transmit speed: Auto
fallback or selectable fixed rate.
Bridge link test
Via the link test the quality of a bridge link can be measured.
Bridge link encryption
With high security TKIP and AES possible
Client mode
Routing or bridge mode possible. In bridge mode multiple IP based end devices can be
operated simultaneously and additionally one non-IP-based end device
Buffer pool
For cushioning of peaks
WMM 802.11e QoS
Data prioritization for TOS data, 802.11e/WMM
WMM Power Save (U-APSD)
Support of active WLAN clients, which support 802.11e power save
Internet dialup
PPPoE, PPTP
Load balancing
Session-round-robin, load-dependent bandwidth
BLD
Broken Link Detection (BLD) per SSID possible.
NTP
NTP client, NTP server, manually
DNS
DNS client, DNS server, DNS relay
DHCP
DHCP client, DHCP server, DHPC relay
Adjustable (no, slow, normal, fast, customized roaming). Adaptable for fast movable client (i.e.
vehicle), to guarantee a roaming without interruption. This is achieved by scanning of the
relevant channels in the background.
Hardware Features
Feature
Description
Certifications
Wi-Fi Certified according 802.11abgn (Rel.7.9.4)
Standards and certifications
R&TTE Directive 1999/5/EG; EN 60950-1 (IEC60950); EN 300 328; EN 301 489-17;
EN 301 489-1; EN 301 893; EN 60601-1-2 (medical electrical devices - Part
1-2)
LAN / WAN
2 x 10/100 Mbps Ethernet twisted pair, autosensing, auto MDI/MDI-X
Serial interface
V.24 interface with D-Sub9 jack for configuration
WLAN
IEEE 802.11a/b/g/n; 1 radio module, 2.4 und 5 GHz band, 3 external antennas
Antenna
Three antenna connectors with RTNC jacks; delivered incl. three 2.5 dBi omni-directional
antennas
Real time clock
Even at power loss the system time will be available for several hours.
Power supply
External wall power supply 230V / 12 V DC, 1 A, with high efficient switching power supply
PoE
Power-over-Ethernet according IEEE 802.3af
Status LEDs
Status + activity for WLAN, Ethernet 1, Ethernet 2
Theft protection
Theft protection optional available
Wall mounting
Integrated in the housing design
Dimensions
Approx. 16.3 cm x 16.8 cm x 5 cm (width x depth x hight)
Weight
Approx. 400 g
Power consumption
Less than 10 Watt
Environment
Temperature operating: 0°C to 40°C; storage: -10°C to 70°C; rel. humidity 10 to 95% (non
condensing)
Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com
bintec W1002n
07.09.2010
Subject to technical
alterations