PRIMERGY RX300 S5
System configurator and order-information guide
August 2010
Contents
Instructions
Configuration diagram
Configurator
0 System software
I
Basic unit
II Processor
III Memory
IV Graphics
V Accessible drives
VI Hard disk drives
VII PCI Controller
VIII Communication/Network
IX System Management Products (RemoteView)
X Miscellaneous
XI Country specific power cord
Change report
PRIMERGY Server
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
Instructions
This document contains basic product and configuration information that will enable you to configure your system via
PC-/System-Architect.
Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete
PRIMERGY Rack system.
You can configure your individual PRIMERGY server in order to adjust your specific requirements.
The System configurator is divided into several chapters that are identical to the current price list and PC-/SystemArchitect.
Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through
the configurator by following the lines from the top to the bottom.
Section
III
Memory, example
There are X memory slots which can be equipped with XXX MB.
It is permissible to make up to X passes through the memory upgrade options
S26361-XXX-XXX
Memory XXX MB
S26361-XXX-XXX
Memory XXX MB
max. X times per system
max. X times per system
X times
In one chapter you can only select as many components (here 4x) as the arrow indicates.
4x
Please note that there are information symbols which indicate necessary information.
For further information see:
http://ts.fujitsu.com/products/standard_servers/index.html
(internet)
https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/current/Pages/default.aspx (extranet)
Fujitsu Technology Solutions x86 PRIMERGY Server
2 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
Configuration diagram PRIMERGY RX300 S5
System unit ( I )
with 3.5" Hard disk drives
Motherboard
Memory CPU1
front side
3 USB
Air channel
VGA
Frontp.
Bay for LocalView LCD
or CSS
Bay for 5,25"x 0,5" SATA-CD
or DVD-ROM
( Channel 0 + 1 +2 )
Xeon DP
Bank 1 (3 Modules)
Bank 2 (3 Modules)
Bank 3 (3 Modules)
Memory CPU2
( Channel 0 + 1 +2 )
Xeon DP
Bank 1 (3 Modules)
Bank 2 (3 Modules)
Bank 3 (3 Modules)
Memory (III )
Processor ( II )
Accessible drives ( V )
rear side
Fan 1 - Fan 5
1. PSU
Needs space for 2
hard disk drives!
3.5"x1,6"
2. PSU
Fan 6 - Fan 10
Redundant systemfans option
Redundant power
supply option
Modular RAID
Support
Backup drive option
Raid Card for IME, Raid 0 / 1E
Raid Card for Raid 5
Low-profile extension slots for:
SCSI Controller for backup( VII )
SAS Disk Array ( VIII )
Communication/Network ( IX )
Miscellaneous ( X )
Hard disk drives ( VI )
3.5"x1" SAS or SATA
Slot 7 PCIe-2 x8 (wired x8), long, notched
Possible to plug x16 cards
3.5"x1" SAS or SATA
Slot 6 PCIe-2 x8 (wired x8), long, notched
Slot 3 wired x8
Slot 5 wired x8
Possible to plug x16 cards
Slot 5 PCIe-2 x8 (wired x4), long
3.5"x1" SAS or SATA
Slot 5 = wired x8 if slot 4 is empty
Slot 4 PCIe-2 x8 (wired x4), long
3.5"x1" SAS or SATA
Slot 3 PCIe-2 x8 (wired x4), long
3.5"x1" SAS or SATA
Slot 3 = wired x8 if slot 2 is empty
Slot 2 PCIe-2 x8 (wired x4), long
Slot 1 PCIe-2 x8 (wired x4), long
3.5"x1" SAS or SATA
Prefered for modular RAID-Controller
Key:
Included in basic unit
Option
One CPU ( first CPU ) and one memory per CPU ( first memory ) has to be selected for an orderable basic unit.
Fujitsu Technology Solutions x86 PRIMERGY Serve
3 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
Configuration diagram PRIMERGY RX300 S5
System unit ( I )
with 8 or 12 2.5" Hard disk drives
Motherboard
Memory CPU1
front side
middle
3 USB
Air channel
VGA
Frontp.
Bay for LocalView LCD
or CSS
Bay for 5,25"x 0,5" SATA-CD
or DVD-ROM
( Channel 0 + 1 +2 )
Xeon DP
Bank 1 (3 Modules)
Bank 2 (3 Modules)
Bank 3 (3 Modules)
Memory CPU2
( Channel 0 + 1 +2 )
Xeon DP
Bank 1 (3 Modules)
Bank 2 (3 Modules)
Bank 3 (3 Modules)
Memory (III )
Processor ( II )
Accessible drives ( V )
rear side
Fan 1 - Fan 5
1. PSU
Needs space for 4
2.5" hard disk drives!
3.5"x1,6"
2. PSU
Fan 6 - Fan 10
Redundant systemfans option
Redundant power
supply option
Backup drive option
Hard disk drives ( VI )
Modular RAID
Support
Raid Card for IME, Raid 0 / 1E
Raid Card for Raid 5
2.5" SAS
Low-profile extension slots for:
SCSI Controller for backup( VII )
SAS Disk Array ( VIII )
Communication/Network ( IX )
Miscellaneous ( X )
2.5" SAS
2.5" SAS
2.5" SAS
Slot 7 PCIe-2 x8 (wired x8), long, notched
Possible to plug x16 cards
2.5" SAS
Slot 6 PCIe-2 x8 (wired x8), long, notched
Slot 3 wired x8
Slot 5 wired x8
Possible to plug x16 cards
2.5" SAS
Slot 5 PCIe-2 x8 (wired x4), long
2.5" SAS
Slot 5 = wired x8 if slot 4 is empty
2.5" SAS
Slot 4 PCIe-2 x8 (wired x4), long
2.5" SAS
Slot 3 PCIe-2 x8 (wired x4), long
2.5" SAS
Slot 3 = wired x8 if slot 2 is empty
2.5" SAS
Slot 2 PCIe-2 x8 (wired x4), long
2.5" SAS
Slot 1 PCIe-2 x8 (wired x4), long
Prefered for modular RAID-Controller
Key:
Included in basic unit
Option
One CPU ( first CPU ) and one memory per CPU ( first memory ) has to be selected for an orderable basic unit.
Fujitsu Technology Solutions x86 PRIMERGY Serve
4 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
Start PRIMERGY RX300 S5
SW - Configurator 32 bit
with OEM-Software
without OEM-Software
for PRIMERGY Server
for PRIMERGY Server
OEM-SW is bound to HW and
is not allowed to be ordered
VMware-Software
- Virtual Infrastructure 3
Usage of OEM SW from MS is
not possible under VMware
separately.
Exception: VMware SW
For all SW products please refer to the corresponding software configurator accessible via
the Extranet under Configuration & Tools, -All configurations, -Software, URL see below.
Microsoft - Software: W **)
- Windows Server 2003 R2,
Standard Edition
Enterprise Edition
PRIMECLUSTER *)
- Clustering
- Load Balancing
! Web Edition, SP2/English
Linux - Software **)
- Open Enterprise Server ***)
- SuSE Linux ES (OEM): LO
- SuSE Linux ES (Support): LS
- Red Hat EL (OEM): LO
- Red Hat EL (Support): LS
Microsoft-Windows: W
Small Business Server 2003 R2,
Standard Edition
for dedicated mono/dual server, see**)
MultiPath, Duplex Data Manager (DDM)
W2K; W2K3 Linux (W-DDM)
Details eg. version numbers are published
in the separate SW-Configurator
Manageability Software: V**)
- RemoteDeploy
- RemoteView Software
- Altiris Server Deployment
- iRMC advanced Pack
***) Supply over distribution or procurement from FSC VP BC Software
You'll find single software configurators and release lists (OS-matrix/system management/security) under following addresses:
for internal users:
for partners:
Continue with PRIMERGY
HW configurator
Fujitsu Technology Solutions x86 PRIMERGY Serve
5 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
Start PRIMERGY RX300 S5
SW Configurator EM64T
with OEM-Software
for PRIMERGY Server
without OEM-Software
for PRIMERGY Server
For all SW products please refer to the corresponding
software configurator accessible via the Extranet under
"Configuration & Tools, -All configurations, -Software,
URL see below.
VMware-Software
- Virtual Infrastructure 3
only
EM64T
Usage of OEM SW from MS is
not possible under VMware
Microsoft - Software: W
- Windows Server 2003 R2,
Standard x64 Edition
Enterprise x64 Edition, SP2
Linux - Software *) **)
only
- SuSE Linux ES (OEM): LO
x86_64 - SuSE Linux ES (Support): LS
- Red Hat EL (OEM): LO
- Red Hat EL (Support): LS
only
MultiPath, Duplex Data Manager (DDM)
EM64T
Windows, Linux (W-DDM)
Manageability Software: V**)
Details eg. version numbers are published
only -vPMS
- RemoteView
2006 std Software
EM64T - RemoteDeploy
- iRMC advanced Pack
in the separate SW-Configurator
You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:
for internal users:
for partners:
Continue with PRIMERGY
HW configurator
Fujitsu Technology Solutions x86 PRIMERGY Serve
6 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
Start PRIMERGY RX300 S5
I
Section
Basic unit
System unit consisting of:
* 2U Housing including one power supply module
- hot plug Power supply unit with 1 PSU module and power cord rack 4m lenght
(can be upgraded with one additional PSU module)
* Fan unit with 5 hot plug system-fans and control logic for 10 fans
- Additional 5 hot plug system-fans as a redundant fans option (option)
* SAS Backplane for 6x 3.5" HD or SAS Backplane for 8 or 12x 2.5" HD
with cable connection to modular RAID Controller
-> 3 different basic units for 6x 3.5" HD or 8 or 12x 2.5" HD
* 9 memory DIMMs per CPU ( max 72GB ) => Total 18 DIMMs ( max 144GB ) for two CPU`s
* Drives/Bays
- 6 bays 1" for hot plug 3.5" HD (1" high) or 8 or 12 bays for hot plug 2.5" HD
- 1 bay for 3.5" and 1.6" high Backup device, consumes 2 bays for 3.5" HD for basic unit 6x 3.5" HD
not possible for basic unit with 12x 2,5" HD
- 1 bay SATA-CD- or DVD-ROM 0,5" height (option)
- 1 bay for opt. CSS-Display or LocalView LC-Display
* Integrated ServerView Diagnostics Technology ( Diagnosis LED`s ) for indication of internal
failed components
Systemboard D2619 with:
* Up to two Xeon Dual Core, Quad-Core or Turbo Quad Core CPU`s ( Nehalem-EP, LGA 1366 socket )
with serial QPI links ( Quick Path Interconnect ) and three memory channels per CPU
First CPU has to be selected for an orderable basic unit,
* Chipset Intel® 5520 (codenamed Tylersburg-EP or 36D)
* 7 PCI slots: - 2x PCIe-2 x8 (wired x8, notched, possible to plug x16 card)
- 5x PCIe-2 x8 (wired x4)
From 4 PCIe-slots each two wired x4 slots can be combined to one wired x8 slot
* 18 memory slots for max. 144GB RAM DDR3 available
- Memory is divided into 9 DIMMs per CPU ( 3 channels with 3 slots per channel )
- Max. three 8GB modules or two 8GB / 16GB quad rank modules are possible per channel
First Memory ( one module ) has to be selected for an orderable basic unit per CPU
- Memory upgrade is possible module wise
- Memory mirrroring is supported with 2 identical modules in channel A+B CPU 1 or D+E CPU 2
- Hot Spare Memory is supported with 3 identical modules in channel A+B+C CPU 1 or D+E+F CPU 2
- SDDC (Chipkill) is supported for memory modules,
* Dual Port 10/100/1000 x4 PCI Express* Gigabit Ethernet Intel LAN controller Zoar on-board
* iRMC S2 (integrated Remote Management Controller) on-board server management controller with
dedicated 10/100 Service LAN-port and integrated graphics controller.
The Service LAN-port can be switched alternatively on standard Gbit LAN port 1
* Graphics Controller integrated in iRMC S2 (integrated Remote Management Controller):
1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz,
640x480x32bpp 85Hz
(1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off)
Interfaces at the rear:
* 1x RS-232-C (serial, 9 pins) (usable for BMC or OS or shared)
* 1x RS-232-C (serial, 9 pins)
* 1x VGA (15 pins)
* 4x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup
* 2x LAN RJ45, 1x Service-LAN RJ45
Interfaces on the front:
* 3x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup
* 1x VGA (15 pins) as an option
Interfaces internal:
* 1x released internal USB Interfaces for backup device,
* 1x USB 2.0 ( UHCI ) with 480MBit/s for dongle funcionality, no USB wakeup
* 2x SATA for internal devices
Software:
* ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates
* Documentation engl. (multilingual on CD)
A
Fujitsu Technology Solutions x86 PRIMERGY Serve
7 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
A
Cables included in basic unit
Connections
Cable
PRIMERGY RX300 S5
1. SATA DVD


2. SAS cables to HDDs




1x cable for SAS signaling
 SAS
 SATA
3. Power cable
Rack version for 19'' racks with
Rack version for 19'' racks with
1 hot plug power supply module (Eff. 89%)
1 hot plug Gold power supply module (Eff. 92%)
Basic unit is without CPU and Memory
Basic unit is without CPU and Memory
For an orderable basic unit one CPU = first CPU and
For an orderable basic unit one CPU = first CPU and
one memory = first memory has to be selected
one memory = first memory has to be selected
Basic unit with
6x 3,5" hard disk drive bays
S26361-K1237-V101
Basic unit with
6x 3,5" HDD bays, Gold PSU
S26361-K1237-V501
S26361-K1237-V201
Basic unit with
8x 2,5" HDD bays, Gold PSU
S26361-K1237-V601
S26361-K1237-V301
Basic unit with
12x 2,5" HDD bays, Gold PSU
S26361-K1237-V701
Basic unit with
8x 2,5" hard disk drive bays
Basic unit with
12x 2,5" hard disk drive bays
S26113-F543-E10
S26113-F555-E10
2nd power supply 800W
2nd Gold power supply 800W
(hot plug) for redundancy
(hot plug) for redundancy
occupies one bay for
occupies one bay for
hot plug power supply
hot plug power supply
max. 1x per system
max. 1x per system
For later upgrade the following kit is available:
S26113-F543-L10
1 power supply module 800W hot plug:
S26113-F555-L10
Supplementary module
Be aware of import restrictions!
Only 1 TPM per system.
S26361-F3552-E1
Loose delivery for later
TPM Module
integration possible for customer.
Trusted Platform Module on Motherboard
Use according to import restrictions
S26361-F3552-L1
max. 1x per system
TPM Module add-on kit
for later integration (loose delivery)
Trusted Platform Module on Motherboard
Use according to import restrictions
max. 1x per system
S26361-F2621-E5
For later upgrade the following kit is available:
Redundant Fans option
Fan upgrade kit:
S26361-F2621-L5
Upgrade of standard into redundant fans
5 single hot plug fans
max. 1x per system
B
Fujitsu Technology Solutions x86 PRIMERGY Serve
8 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
B
PRIMERGY 19" Rack
S26361-F2735-E101
RMK-F1_1-2U Server
S26361-F2735-E110
RMK-P_1-2U Server
S26361-F2735-E111
telescopic rail, full extraction,
telescopic rail, partial extraction
Only for loose deliveries
1-hand-mounting
lower costs option
No mounting in Racks possible
consisting of
consisting of
max. 1x per system
- 1 pair of telescopic rails
- 1 pair of telescopic rails
with easy-mounting-clips
- 1 bracket DC-PC-3rd-Rack
1x per system
S26361-F2735-E7
Cable management PC-Rack
No Rackmount-Kit option
with partial extraction
- 1 bracket DC-PC-3rd-Rack
1x per system
S26361-F2201-E20
Cable arm 3rd P-Rack
- for FSC Primecenter /
- for 3rd party
Datacenter Racks
1x per system
C
S26361-F2735-L101
- not for 3rd party
1x per system
S26361-F2735-L110
RMK_1U Server
for loose delivery
partial extraction is lower cost
version of RMK. Server could not
completly pulled out of the Rack
In case nor cable arm is ordered,
Server must be prevent of beeing
pulled out.
S26361-F2735-L7
Cable management PC-Rack
for loose delivery
PRIMERGY PRIMECENTER-rack
for 3rd party rack cable routing
please order
SNP:SY-F1647E301-P
Installation ex works for one
S26361-F2201-L20
Cable arm 3rd party racks
server or subsystem.
for loose delivery
Hereby the rack will be delivered
completely pre-mounted and
all wired connections are tested.
With racks 12U, 24U, 38U:
Systems and components
PRIMERGY 42/23U rack
will be delivered installed in the rack
PRIMERGY Classic 19" rack is not supported
With racks 46U:
Systems and components
"Rack-mounting ex factory"
will be delivered separately
This service is to be ordered once
To be ordered only together with
per installable server/storage
a PRIMERGY PRIMECENTER rack
subsystem, in order to get the
e.g.:
server/storage subsystem
S26361-K826-V10x
mounted into the PRIMERGY racks.
refer configurator PC-Rack
In case of the 46 U PRIMERGY Rack,
max. 1x per System
this service has to be ordered,
to get the mounting kits and the
cables installed.
C
Fujitsu Technology Solutions x86 PRIMERGY Serve
9 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
C
II
Section
Processor
There are 2 processor sockets available.
The first socket is always equipped with the first CPU which can be selected via configurator
It is also possible to upgrade a dual-processor system later on with a second CPU
Two processors with different clock frequencies are not possible
A multi-processor operating system is required for a dual-processor system.
Note: Max. DDR3 Bus Speed depends on:
Max. two CPU`s can be selected per basic unit
One of following CPU´s has to be selected as first CPU
for an orderable basic unit
Optional second CPU has to be the same type like the first CPU
- max. DDR3 Bus Speed from the CPU and
- max. DDR3 Memory Speed and
- max. memory modules on one memory channel
Dual-Core CPU with max. DDR3 Bus Speed 800MHz
- 1x 64-bit Intel Xeon DP (4MB shared TLC = Third Level Cache )
and
with passive
1066 or heat
1333MHz
sink Frontside Bus
occupies socket for one CPU
Xeon DP E5502 (1,86GHz/4M/4,8GT) / 80W
S26361-F3277-E186
Quad-Core CPU`s with max. DDR3 Bus Speed 800MHz
- 1x 64-bit Intel Xeon DP (4MB shared TLC = Third Level Cache )
and
with passive
1066 or heat
1333MHz
sink Frontside Bus
occupies socket for one CPU
Xeon DP E5504 (2.00GHz/4M/4,8GT) / 80W
Xeon DP E5506 (2.13GHz/4M/4,8GT) / 80W
S26361-F3278-E200
S26361-F3278-E213
Turbo Quad-Core CPU`s with max. DDR3 Bus Speed 1066MHz
- 1x 64-bit Intel Xeon DP (8MB shared TLC = Third Level Cache ); Hyper-Threading (HT)
and
with passive
1066 or heat
1333MHz
sink Frontside Bus
occupies socket for one CPU
Xeon DP E5520 (2.26GHz/8M/5,86GT) / 80W
S26361-F3279-E226
Xeon DP E5530 (2.40GHz/8M/5,86GT) / 80W
S26361-F3279-E240
Xeon DP E5540 (2.53GHz/8M/5,86GT) / 80W
S26361-F3279-E253
Turbo Quad-Core CPU`s with max. DDR3 Bus Speed 1333MHz
- 1x 64-bit Intel Xeon DP (8MB shared TLC = Third Level Cache ); Hyper-Threading (HT)
and
with passive
1066 or heat
1333MHz
sink Frontside Bus
occupies socket for one CPU
Xeon DP X5550 (2.66GHz/8M/6,4GT) / 95W
Xeon DP X5560 (2.80GHz/8M/6,4GT) / 95W
Xeon DP X5570 (2.93GHz/8M/6,4GT) / 95W
Xeon DP W5590 (3.33GHz/8M/6,4GT) / 130W
S26361-F3280-E267
S26361-F3280-E280
S26361-F3280-E293
S26361-F3337-E333
Low Voltage Quad-Core CPU with max. 800MHz DDR3 speed ( 4.8GT/s)
- 1x 64-bit Intel Xeon DP (4MB shared TLC = Third Level Cache )
and
with passive
1066 or heat
1333MHz
sink Frontside Bus
occupies socket for one CPU
Xeon LV DP L5506 (2,13GHz/4M/4,8GT) / 60W
S26361-F3281-E213
Low Voltage Turbo Quad-Core CPU`s with max. DDR3 Bus Speed 1066MHz
- 1x 64-bit Intel Xeon DP (8MB shared TLC = Third Level Cache ); Hyper-Threading (HT)
and
with passive
1066 or heat
1333MHz
sink Frontside Bus
occupies socket for one CPU
Xeon LV DP L5520 (2,26GHz/8M/5,86GT) / 60W
S26361-F3281-E226
Xeon LV DP L5530 (2,40GHz/8M/5,86GT) / 60W
S26361-F3281-E240
D
Fujitsu Technology Solutions x86 PRIMERGY Serve
10 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
D
III
Section
Memory
- There are 9 memory slots for max. 72GB DDR3 RAM per CPU available with 8GB DIMMs
=> max. 144GB for two CPU`s ( 72GB per CPU )
( For explanation of following terms refer to section "Memory Configurations"
- The memory area is divided into 3 channels per CPU with 3 slots per channel
- Slot 1 of each channel belongs to memory bank 1, the slot 2 belongs to memory bank 2 and
slot 3 belongs to memory bank 3
No mix of dual rank and quad rank modules possible for the configuration of the same CPU
1.) In the independent channel mode is following configuration possible
- Each slot can optionally be equipped with 2GB single rank, 4GB and 8GB dual rank DDR3 modules or
with 8GB quad rank DDR3 modules
2.) In the spare channel mode is following configuration possible
- Each memory bank can optionally be equipped with 3x2GB single rank,
3x4GB and 3x8GB dual rank DDR3 modules or with 3x8GB quad rank DDR3 modules
Each slot of one bank has to be equipped with identical modules for spare channel mode
In channel A and B of CPU 1 or channel D and E of CPU 2 are always the active memory modules,
in channel C of CPU 1 and channel F of CPU 2 is always the spare module
3.) In the mirrored channel mode is following configuration possible
- Each memory bank can optionally be equipped with 2x2GB single rank,
2x4GB and 2x8GB dual rank DDR3 modules or with 2x8GB quad rank DDR3 modules
In each memory bank channel A and B of CPU 1 or channel D and E of CPU 2 have to be equipped with
identical modules for mirrored channel mode. Channel C of CPU 1 and channel F of CPU 2 is not equipped
In channel B is always the mirrored memory of channel A of CPU 1
In channel E is always the mirrored memory of channel D of CPU 2
DDR3 1066 and 1333MHz modules can be mixed, but run always with the slower speed.
With three DIMMs per channel only 800MHz is possible.
- For each CPU minimum 1 memory module has to be configured in Independent Channel Mode
( => Additional memory extensions can still be configured up to eight times per CPU ) or
one bank has to be equipped with two modules (channel A+B for CPU 1 or D+E for CPU 2) in
Mirrored Channel Mode
( => Additional memory extensions can still be configured up to two times per CPU ) or
one bank has to be equipped with three modules (channel A+B+C for CPU 1 or D+E+F for CPU 2)
in Spare Channel Mode or Performance Mode
( => Additional memory extensions can still be configured up to two times per CPU )
- ECC with SDDC (Chipkill) is standard for RX300 S5.
For a description of memory configurations refer to section "Memory Configurations"
Minimum one memory module or order code per CPU = first memory
Registered (reg) RDIMMs
Note 1.)
Max. DDR3 memory speed depends on the memory configuration
of one CPU memory channel and on the speed of the CPU itself.
For "independent channel mode" usage!
- One DDR3-1066 PC3-8500 reg ECC memory module
Memory 2GB (single rank)
Memory 4GB (dual rank)
Memory 8GB (dual rank)
S26361-F3284-E513
S26361-F3284-E514
S26361-F3284-E515
Choose up to 9 order codes above per CPU.
9x for each CPU
with max.
3 modules
per channel
The memory channel with the lowest speed defines the speed
of all CPU channels in the system, also for the channels of the
second CPU if configured.
One DIMM per channel = max. 1333MHz,
two DIMMs per channel = max. 1066MHz,
three DIMMs per channel = max. 800MHz,
Registered (reg) RDIMMs
For "independent channel mode" usage!
- One DDR3-1333 PC3-10600 reg ECC memory module
Memory 2GB (single rank)
Memory 4GB (dual rank)
Memory 8GB (dual rank)
S26361-F3285-E513
S26361-F3285-E514
S26361-F3285-E515
Note 2.)
Max. DDR3 memory speed 1333MHz is only
possible with CPU`s X5550, X5560 and X5570
Choose up to 9 order codes above per CPU.
E1
E2
Fujitsu Technology Solutions x86 PRIMERGY Serve
11 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
E1
E2
S26361-F3284-E1
Spare Channel Mode Installation
With this order code a BIOS setup
for spare mode is factory preinstalled
The three identical memory modules
of following order codes are always
equipped in one memory bank to use
the Spare Channel Mode
In this mode only two modules are active
the third module is the spare module
S26361-F3284-E2
Performance Mode Installation
With this order code BIOS setup
is default for highest performance
The three identical memory modules
of following order codes are always
equipped in one memory bank to run
with highest performance
In this mode all three modules are active
and full capacity can be used
Registered (reg) RDIMMs
SP = for "Spare Channel and Performance Mode" usage!
See Note 1.)
- Three DDR3-1066 PC3-8500 reg ECC memory modules
Memory SP 6GB (3x 2GB single rank)
S26361-F3284-E533
= 4GB usable memory for Spare Channel Mode
= 6GB usable memory for Performance Mode
Memory SP 12GB (3x 4GB dual rank)
S26361-F3284-E534
= 8GB usable memory for Spare Channel Mode
= 12GB usable memory for Performance Mode
Memory SP 24GB (3x 8GB dual rank)
S26361-F3284-E535
= 16GB usable memory for Spare Channel Mode
= 24GB usable memory for Performance Mode
Choose up to 3 order codes above per CPU.
3x for each CPU
with max.
3 modules
per channel
Registered (reg) RDIMMs
SP = for "Spare Channel and Performance Mode" usage!
See Note 2.)
- Three DDR3-1333 PC3-10600 reg ECC memory modules
Memory SP 6GB (3x 2GB single rank)
S26361-F3285-E533
= 4GB usable memory for Spare Channel Mode
= 6GB usable memory for Performance Mode
Memory SP 12GB (3x 4GB dual rank)
S26361-F3285-E534
= 8GB usable memory for Spare Channel Mode
= 12GB usable memory for Performance Mode
Memory SP 24GB (3x 8GB dual rank)
S26361-F3285-E535
= 16GB usable memory for Spare Channel Mode
= 24GB usable memory for Performance Mode
Choose up to 3 order codes above per CPU.
F1
F2
Fujitsu Technology Solutions x86 PRIMERGY Serve
12 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
F1
F2
S26361-F3284-E3
Mirrored Channel Mode Installation
With this order code a BIOS setup
for Mirrored Channel Mode is
factory preinstalled
The two identical memory modules
of following order codes are always
equipped in one memory bank to use
the Mirrored Channel Mode
In this mode only one module contains
active data, the second modul contains
the mirrored data
Registered (reg) RDIMMs
MM = for "Mirrored Channel Mode" usage!
See Note 1.)
- Two DDR3-1066 PC3-8500 reg ECC memory modules
Memory MM 4GB (2x 2GB single rank)
S26361-F3284-E523
= 2GB usable memory for Mirrored Channel Mode
Memory MM 8GB (2x 4GB dual rank)
S26361-F3284-E524
= 4GB usable memory for Mirrored Channel Mode
Memory MM 16GB (2x 8GB dual rank)
S26361-F3284-E525
= 8GB usable memory for Mirrored Channel Mode
Choose up to 3 order codes above per CPU.
3x for each CPU
with max.
3 modules
per channel
Registered (reg) RDIMMs
MM = for "Mirrored Channel Mode" usage!
See Note 2.)
- Two DDR3-1333 PC3-10600 reg ECC memory modules
Memory MM 4GB (2x 2GB single rank)
S26361-F3285-E523
= 2GB usable memory for Mirrored Channel Mode
Memory MM 8GB (2x 4GB dual rank)
S26361-F3285-E524
= 4GB usable memory for Mirrored Channel Mode
Memory MM 16GB (2x 8GB dual rank)
S26361-F3285-E525
= 8GB usable memory for Mirrored Channel Mode
Choose up to 3 order codes above per CPU.
IV
Section
Graphics
Graphics Controller integrated in iRMC S2 (integrated Remote Management Controller):
1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz, 640x480x32bpp 85Hz
(1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off)
S26361-F2571-E16
Optional Front-VGA
consists of internal cable and
front VGA connector
max. 1x per system
S26361-F2748-E633
PY VGA LP card 256MB PCI-e x1
NVIDIA NVS290
256 MB PCIe-x1
2x DVI or 2x VGA or
1x DVI plus 1x VGA
cables adapters included
Dual head + fully 3-D
supported for Windows OS
only native driver support for Linux OS
low profile bracket
max. 1x per system
The hight end optional NVIDIA NVS290 graphic card offers dual head operation
and fully 3D video support.
The cables for either two times DVI or VGA connections are part of the delivery.
Remote Video direction via iRMC must be disabled.
This PCIe-x1 card can also be installed in any PCIe-x4, x8 or x16 slot.
Only one card per server is allowed.
PY VGA card must be installed in slot 4
S26361-F2748-L633
PY VGA LP card 256MB PCI-e x1
for loose delivery
G
Fujitsu Technology Solutions x86 PRIMERGY Serve
13 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
Memory Configuration PRIMERGY RX300 S5
Each CPU offers 9 Slots for DDR3 Memory Modules organised in 3 Banks and 3 Channels.
If you need more than 9 Slots you have to configure the 2nd CPU.
Depending on the amount of memory configured you can decide between 4 basic modes of operation
(see explanation below).
For RX300 S5 only registered DDR3 memory modules ( RDIMM ) are available.
Mode
chip kill support
Independant Channel Mode
Configuration
any
1, 2 or 3 Modules per Bank
RDIMM Application
yes
detect multi-bit errors
x
x
offers max. flexibility, upgradeability, capacity
use UDIMM modules for lowest cost
Mirrored Channel Mode
2 identical Modules / Bank **)
x
offers maximum security
Performance Mode *)
3 identical Modules / Bank **)
x
offers maximum performance and capacity
Spare Channel Mode *)
3 identical Modules / Bank **)
x
balances security and capacity
*) = Performance Mode and Spare mode use different BIOS settings.
**) = technically possible but no Order Numbers available, use at your own risk
x = order codes available
Configuration hints:
- The memory sockets on the systemboard offer a color coding:
Bank I
black sockets
Bank II blue sockets
Bank III green sockets
- A so called Bank consits of 1 memory module on every Channel available on one CPU (examples see below)
Bank I on CPU 1
up to 3 memory modules connected to Channel A, B and C on the first CPU
Bank II on CPU 1 up to 3 memory modules connected to Channel A, B and C on the first CPU
Bank III on CPU 1 up to 3 memory modules connected to Channel A, B and C on the first CPU
Bank I on CPU 2
up to 3 memory modules connected to Channel D, E and F on the second CPU
Bank II on CPU 2 up to 3 memory modules connected to Channel D, E and F on the second CPU
Bank III on CPU 2 up to 3 memory modules connected to Channel D, E and F on the second CPU
- See below and next page for a detailed descriptions of the memory configuration supported.
Fujitsu Technology Solutions x86 PRIMERGY Serve
14 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
Channel E
Channel F
Bank I
Data
Data
Data
(black sockets)
Bank II
Data
Data
Data
(blue sockets)
Bank III Data
Data
Data
(green sockets)
1st XEON CPU
(Dual-or Quad Core)
Channel D
Channel C
Channel B
Channel A
1. Independent Channel Mode
Data
Data
Data
optional, same type in Bank per CPU
Data
Data
Data
optional, any type
Data
Data
Data
required
required if 2nd CPU is configured
--------
not used
2nd XEON CPU
(Dual-or Quad Core)
Independent Channel Mode allows all channels to be populated in any order
Can run with differently rated DIMMs and use the settings of the slowest DIMM within a channel
Channel E
Channel F
Bank I
Data
Mirror -------(black sockets)
Bank II
Data
Mirror -------(blue sockets)
Bank III Data
Mirror -------(green sockets)
1st XEON CPU
(Dual-or Quad Core)
Channel D
Channel C
Channel B
Channel A
2. Mirrored Channel Mode
Data
Mirror
--------
Data
Mirror
--------
Data
Mirror
--------
required
required if 2nd CPU is configured
optional, same type in Bank per CPU
--------
not used
2nd XEON CPU
(Dual-or Quad Core)
Mirrored Channel Mode requires identical modules on channel A and B (1st CPU) or channel D and E (2nd CPU)
50% of the capacity is used for the mirror => the available memory for applications is only half of the installed memory
Channel C (1st CPU) or channel F (2nd CPU) are not usable in Mirrored Channel Mode
Channel E
Channel F
Bank I
Data
Data
Data
(black sockets)
Bank II
Data
Data
Data
(blue sockets)
Bank III Data
Data
Data
(green sockets)
1st XEON CPU
(Dual-or Quad Core)
Channel D
Channel C
Channel B
Channel A
3. Performance Channel Mode
Data
Data
Data
optional, same type in Bank per CPU
Data
Data
Data
optional, any type
Data
Data
Data
required
required if 2nd CPU is configured
--------
not used
2nd XEON CPU
(Dual-or Quad Core)
Performance Channel Mode requires identical modules on all channels of each Bank per CPU
Channel E
Channel F
Bank I
Data
Data
Spare
(black sockets)
Bank II
Data
Data
Spare
(blue sockets)
Bank III Data
Data
Spare
(green sockets)
1st XEON CPU
(Dual-or Quad Core)
Channel D
Channel C
Channel B
Channel A
4. Spare Channel Mode
Data
Data
Spare
optional, same type in Bank per CPU
Data
Data
Spare
optional, any type
Data
Data
Spare
required
required if 2nd CPU is configured
--------
not used
2nd XEON CPU
(Dual-or Quad Core)
Spare Channel Mode requires identical modules on all channels of each Bank per CPU
one third of the capacity is used for the spare => the available memory for applications is two thirds of the installed memroy
Fujitsu Technology Solutions x86 PRIMERGY Serve
15 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
G
V
Section
Accessible drives
Setup RX300 S5 by ServerStart is supported with following configurations:
no DVD, no CD:
remote installation only ( PXE service & DHCP server required)
built in CD/DVD or USB CD/DVD disk drive:
UNC Network share reachable or USB Floppy connected
USB Floppy, no CD/DVD:
USB CD/DVD connected
If installation is done locally, make sure you have
external FDD available for driver installation.
Following USB Components are available
1) USB DVD SM / Blu-Ray
External SuperMulti Drive (as soon as released)
S26341-F103-L82
External Blu-Ray Drive (as soon as released)
2) USB Keyboard:
KBPC PX D, professional keyboard
S26341-F103-L83
S26381-K340-V120
S26381-K415-L100
3) USB Mouse: Optical Wheel Mouse Tilt USB/PS2
4) USB Memorybird:
1x
Memorybird P 4GB, SLC flash
S26391-F6047-L104
MyUSBS A910 8GB, MLC Flash
S26391-F6048-L208
S26361-F3531-E2
S26361-F3269-E2
Blu-ray Combo slim SATA
DVD-RW supermulti slim SATA
6x BD-ROM, 16x DVD, 40x CD
all formats, DUAL/DL, DVD-RAM
BD DL and all CD/DVD formats
only W2K, W3K and Linux
0.5 x 5.25", black bezel
0.5 x 5.25", black bezel
max. 1x per system
max. 1x per system
S26361-F3324-E7
S26361-F3857-E7
Tape drive DDS Gen5 USB 3.5"
RDX drive USB 3.5" internal
36GB, 3MB/s, USB 2.0
80-320GB, 25MB/s, USB 2.0
Only for basic unit
1.6 x 3.5", black bezel
1.6 x 3.5", black bezel
V1xx
within a tape cage
incl. description (Ger/US)
within a tape cage
incl. description (Ger/US)
RDX cartridges must be ordered separately
data and cleaning cartridge
without RDX cartridges
RDX 80GB = S26361-F3857-L80
occupies 2 x 1" hard disk bays
occupies 2 x 1" hard disk bays
RDX 160GB = S26361-F3857-L160
max. 1x per system
max. 1x per system
RDX 320GB = S26361-F3857-L320
S26361-F3324-E5
S26361-F3857-E5
Tape drive DDS Gen5 USB 3.5"
RDX drive USB 3.5" internal
36GB, 3MB/s, USB 2.0
Connector: USB "B"
80-320GB, 25MB/s, USB 2.0
Connector: USB "B"
with USB cable
incl. description (Ger/US)
with USB cable
incl. description (Ger/US)
RDX cartridges must be ordered separately
data and cleaning cartridge
without RDX cartridges
RDX 80GB = S26361-F3857-L80
1.6 x 3.5", black bezel
1.6 x 3.5", black bezel
RDX 160GB = S26361-F3857-L160
max. 1x per system
max. 1x per system
RDX 320GB = S26361-F3857-L320
1x
Only for basic unit
V2xx
H
Fujitsu Technology Solutions x86 PRIMERGY Serve
16 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
H
VI
Section
Hard disks drives
Modular Raid controller is connected to internal HDDs
For basic units V1xx up to 6 SAS 3.5" hard disks can be configured also in mixed configuration.
If the option "Tape drive" is configured only 4 bays for hard disks are available
Mixed configurations with SAS (F3291) and BC-SATA 3.5" HD`s (F3294) are released
No mix between ECO SATA and SAS possible
S26361-F3293-E160
HD 160GB 7.2krpm 3.5"
7200rpm,<9.0 ms, 8MB Cache
ECO SATA 3Gb/s
hot plug/hot replace tray
max. 6x (or 4x) per system
6x /
4x with tape for
basic units V1xx
S26361-F3294-E250
HD 250GB 7.2krpm 3.5"
7200rpm,<9.0 ms, 8MB Cache
BC-SATA 3Gb/s
hot plug/hot replace tray
max. 6x (or 4x) per system
S26361-F3294-E500
HD 500GB 7.2krpm 3.5"
7200rpm,<9.0 ms, 8MB Cache
BC-SATA 3Gb/s
hot plug/hot replace tray
max. 6x (or 4x) per system
S26361-F3294-E750
HD 750GB 7.2krpm 3.5"
7200rpm,<9.0 ms, 8MB Cache
BC-SATA 3Gb/s
hot plug/hot replace tray
max. 6x (or 4x) per system
S26361-F3294-E100
HD 1TB 7.2krpm 3.5"
7200rpm,<9.0 ms, 8MB Cache
BC-SATA 3Gb/s
hot plug/hot replace tray
max. 6x (or 4x) per system
S26361-F3291-E573
HD 73GB 15krpm 3.5"
15.000rpm,<4ms, 8MB Cache
SAS 3Gb/s
hot plug/hot replace tray
max. 6x (or 4x) per system
S26361-F3291-E514
Hard disk 146GB 15krpm 3.5"
15.000rpm,<4ms, 8MB Cache
SAS 3Gb/s
hot plug/hot replace tray
max. 6x (or 4x) per system
S26361-F3291-E530
HD 300GB 15krpm 3.5"
15.000rpm,<4ms, 8MB Cache
SAS 3Gb/s
hot plug/hot replace tray
max. 6x (or 4x) per system
S26361-F3291-E545
HD 450GB 15krpm 3.5"
15.000rpm,<4ms, 8MB Cache
SAS 3Gb/s
hot plug/hot replace tray
max. 6x (or 4x) per system
For basic units V2xx up to 8 SAS 2.5" hard disks plus the option "Tape drive" can be configured.
For basic units V3xx up to 12 SAS 2.5" hard disks can be configured.
Mixed configurations are released
S26361-F3298-E32
SSD 32GB
SATA 3Gb/s
hot plug/hot replace tray
max. 8x or 12x per base unit
8x for
basic units V2xx,
12x for V3xx
S26361-F3298-E64
SSD 64GB
SATA 3Gb/s
hot plug/hot replace tray
max. 8x or 12x per base unit
S26361-F3292-E173
HD 73GB 10krpm 2.5"
10000rpm,<4,5ms, 8MB Cache
SAS 3Gb/s
hot plug/hot replace tray
max. 8x or 12x per base unit
S26361-F3292-E114
HD 146GB 10krpm 2.5"
10000rpm,<4,5ms, 8MB Cache
SAS 3Gb/s
hot plug/hot replace tray
max. 8x or 12x per base unit
S26361-F3292-E573
HD 73GB 15krpm 2.5"
15000rpm,<4,5ms, 8MB Cache
SAS 3Gb/s
hot plug/hot replace tray
max. 8x or 12x per base unit
S26361-F3292-E514
HD 146GB 15krpm 2.5"
15000rpm,<4,5ms, 8MB Cache
SAS 3Gb/s
hot plug/hot replace tray
max. 8x or 12x per base unit
S26361-F3601-E160
HD 160GB 7.2krpm 2.5"
7200rpm,<10,5ms, 8MB Cache
BC SATA
hot plug/hot replace tray
max. 8x or 12x per base unit
S26361-F3601-E500
HD 500GB 7.2krpm 2.5"
7200rpm,<10,5ms, 8MB Cache
BC SATA
hot plug/hot replace tray
max. 8x or 12x per base unit
S26361-F3292-E130
HD 300GB 10krpm 2.5"
10000rpm,<4,5ms, 8MB Cache
SAS 3Gb/s
hot plug/hot replace tray
max. 8x or 12x per base unit
I
Fujitsu Technology Solutions x86 PRIMERGY Serve
17 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
H
VI
Section
SAS 6G HD's and Controller for basic units V2xx up to 8 SAS 2.5"
For basic units V2xx up to 8 SAS 2.5" hard disks plus the option "Tape drive" can be configured.
Mixed configurations with SSD and SATA 2.5" HD`s are NOT released
Mixed configurations with SAS and SATA 2.5" HD`s are NOT released
only with 8x2,5" BU (V201)
1x
S26361-F3554-E512
RAID Ctrl SAS 6G 8port internal
Based on chip LSISAS2108
LSI MegaRAID
512MB Cache with ECC
RAID 0, 1, 10, 5, 50, 6, 60
optional BBU
Support for 3Gb/s and 6Gb/s
SATA and SAS hard drives
PCIe x4
Low-profile MD2 form factor
max. 1x per system
Only for basic unit
V2xx
S26361-F3257-E116
Cache Battery Backup Unit
with 16cm cable set
max. 1x per Controller
1x
Only for basic unit
V2xx
S26361-F4006-E114
HD 146GB 10krpm 2.5"
10000rpm,<4,5ms, 8MB Cache
SAS 6Gb/s
hot plug/hot replace tray
max. 8x per base unit
S26361-F4006-E130
HD 300GB 10krpm 2.5"
10000rpm,<4,5ms, 8MB Cache
SAS 6Gb/s
hot plug/hot replace tray
max. 8x per base unit
Only for basic unit
V2xx
S26361-F4006-E573
HD 73GB 15krpm 2.5"
15000rpm,<4,5ms, 8MB Cache
SAS 6Gb/s
hot plug/hot replace tray
max. 8x per base unit
S26361-F4006-E514
HD 146GB 15krpm 2.5"
15000rpm,<4,5ms, 8MB Cache
SAS 6Gb/s
hot plug/hot replace tray
max. 8x per base unit
8x for
basic units V2xx,
I
Fujitsu Technology Solutions x86 PRIMERGY Serve
18 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
I
VII
Section
Modular Raid 0/1 and Raid5 Controller
S26361-F3257-E8
8 port SAS RAID Controller
LSI
MegaRAID SAS 1068
RAID 0, 1 & 1E
no Cache, no BBU
SAS 3Gb/sec
8 internal ports
PCIe x4, 160mm
with combi bracket
max. 1x per system
Modular Raid 0/1 controller with IME support for SAS/SATA-HDs
IME (Integrated Mirroring Enhanced) offers the RAID levels 0, 1, 1E
IME is a RAID 0, 1 implementation, whereby RAID 1 can operate
an odd number of hard disks. Up to 8 hard disks including one hot spare HD
are possible (limited by HHD slots in system).
Administration of IME is possible with the LSI Global Array Manager (GAM).
Windows2000/2003 as well as SUSE and RedHat Linux are supported
(Restrictions refer to Software Configurator)
The SAS IME solution supports 2 independent RAID volumes.
Modular Raid controller must be ordered, if at least one internal HDD is configured!
Modular Raid 5 controller for SAS/SATA-HDs
RAID levels 0, 1, 10, 5, 50, 6 and 60 are supported
The RAID controller supports 6 HDDs on the 6 internal SAS ports.
Tapes and optical devices (e.g. DVD) are not suported.
Also there is no support of any external storage by this RAID solution.
1x
S26361-F3257-E256
8 port SAS RAID Controller
LSI
MegaRAID SAS 1078
256MB Cache with ECC
RAID 0, 1, 10, 5, 50, 6, 60
optional BBU
SAS 3Gb/sec
8 internal ports
PCIe x4, 160mm
with combi bracket
max. 1x per system
S26361-F3257-E512
8 port SAS RAID Controller
LSI
MegaRAID SAS 1078
512MB Cache with ECC
RAID 0, 1, 10, 5, 50, 6, 60
optional BBU
SAS 3Gb/sec
8 internal ports
PCIe x4, 160mm
with combi bracket
max. 1x per system
S26361-F3257-E116
Cache Battery Backup Unit
with 16cm cable set
max. 1x per Controller
S26361-F3257-E116
Cache Battery Backup Unit
with 16cm cable set
max. 1x per Controller
For the basic unit with
12x 2.5" HDDs (V301)
a modular Raid 5 Ctrl.
must be ordered!
for loose delivery please order
S26361-F3257-L110
J
Fujitsu Technology Solutions x86 PRIMERGY Serve
19 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
J
SAS-/SCSI-/ Fibre-Channel Controller Low Profile
* 2 PCIe-2 slots wired x8 and 5 PCIe-2 slots wired x4:
Slot 7 and 6 are wired x 8 and notched
Slot 5 is wired x8 if slot 4 is not populated
Slot 3 is wired x8 if slot 2 is not populated
Slot 1 is wired x 4
A PCIe-2 x4 card can also be plugged in a PCIe-2 x8 slot
A PCIe-2 x8 card can also be plugged in a PCIe-2 x4 slot (mechanical x8)
A PCIe-2 x16 card can be plugged in a notched PCIe-2 x8 slot
SAS-controller for external backup drives
S26361-F3271-E201
SAS Controller 3Gb/s 8 port LP
LSI SAS3442E-R Low Profile
PCIe x4,
int: 4 port
ext: 4 port
max. 3x per system
SCSI controllers for external backup drives
S26361-F3270-E201
SCSI U320 Controller
Adaptec SCSI Card 29320LPE
Low Profile
PCIe x1,
int: LVD HD68
ext: VHDCI 68pin
max. 2x per system
Fibre Channel Controller for external storage systems
4x
S26361-F3306-E201
S26361-F3306-E202
4GBit/s FC Controller
4GBit/s FC Controller
Emulex
Emulex
LPe1150, full height bracket
LPe11002, Low Profile bracket
1 channel 4GBit/sec FC Controller
2 channel 4GBit/sec FC Controller
LC Interface for 50µm Fiber
LC Interface for 50µm Fiber
PCIe x4, 170mm
max. 4x per system
PCIe x4, 170mm
max. 4x per system
S26361-F3483-E201
S26361-F3483-E202
4GBit/s FC Controller
4GBit/s FC Controller
Qlogic
Qlogic
QLE2460, full height bracket
QLE2462, low profile bracket
No mix and match of different
1 channel 4GBit/sec FC Controller
2 channel 4GBit/sec FC Controller
FC Controllers possible.
LC Interface for 50µm Fiber
LC Interface for 50µm Fiber
PCIe x4, 170mm
max. 4x per system
PCIe x4, 170mm
max. 4x per system
All controllers for the connection of external
storage system are delivered without cables.
For the configuration of external cabling see
the configurator for external storage system.
For Fibre Channel SAN also other componets like
S26361-F3961-E201
S26361-F3961-E202
switches, SFPs and optical wires are orderable
8GBit/s FC Controller
8GBit/s FC Controller
(for details see price liste)
Emulex
Emulex
LPe1250, low profile bracket
LPe12002, low profile bracket
1 channel 8GBit/sec FC Controller
2 channel 8GBit/sec FC Controller
LC Interface for 50µm Fiber
LC Interface for 50µm Fiber
PCIe x4, 170mm
max. 4x per system
PCIe x4, 170mm
max. 4x per system
K
Fujitsu Technology Solutions x86 PRIMERGY Serve
20 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
K
SAS RAID controller for JBOD subsystems
S26361-F3890-E201
S26361-F3890-E230
8 port SAS RAID Controller
8 port SAS RAID Controller
LSI
LSI
MegaRAID SAS8880E
MegaRAID SAS8880E
512MB Cache with ECC
512MB Cache with ECC
iBBU max. 2x per system possible
RAID 0, 1, 10, 5, 50, 6 & 60
RAID 0, 1, 10, 5, 50, 6 & 60
without iBBU
with iBBU
for loose delivery please order
S26361-F3890-L501
Contr. w/o BBU
SAS 3Gb/sec
SAS 3Gb/sec
S26361-F3890-L13
8 port external
8 port external
PCIe x4, 167mm
PCIe x4, 167mm
low profile bracket
max. 1x per system
low profile bracket
max. 1x per system
optional BBU
L
Fujitsu Technology Solutions x86 PRIMERGY Serve
21 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
L
VIII
Section
Communication / Network
Dual Port GBit on-board LAN Controller
Gigabit Ethernet Controller on-board
Dual Port GBit LAN controller
Intel 82575EB (Zoar) *
ext: for RJ 45-connector
SW: AFT, VLAN, Fast Channel
Teaming: Failover, Load Balancing
The Intel LAN Controllers 1000TX and 1000SX
can be used with the on-board controller in Teaming Mode.
Two onboard LAN ports can likewise educate a team.
* Supporting iSCSI boot (also diskless) by system BIOS and native iSCSI initiators
* 2 PCIe-2 slots wired x8 and 5 PCIe-2 slots wired x4:
Slot 7 and 6 are wired x 8 and notched
Slot 5 is wired x8 if slot 4 is not populated
Slot 3 is wired x8 if slot 2 is not populated
Slot 1 is wired x 4
A PCIe-2 x4 card can also be plugged in a PCIe-2 x8 slot
A PCIe-2 x8 card can also be plugged in a PCIe-2 x4 slot (mechanical x8)
A PCIe-2 x16 card can be plugged in a notched PCIe-2 x8 slot
PCI-Express Adapter 1000TX/SX
S26361-F3516-E201 (Shelter Island)
Gigabit Ethernet Controller 1000TX LP
Eth Ctrl 1x1Gbit PCI-e Gigabit CT DT Cu LP
Intel® Gigabit CT Desktop Adapter
PCIe x1
ext: for RJ45-connector, Cat 5
max. 4x per system
S26361-F3241-E201 (Glyndon )
Gigabit Ethernet Contr. 1000TX
S26361-F3242-E201 (Sheepshead Bay )
Gigabit Ethernet Contr. 1000SX
Eth Ctrl 1x1Gbit PCI-e Pro/1000PT Cu LP
Eth Ctrl 1x1Gbit PCI-e Pro/1000PF LC LP
Intel PRO/1000 PT Server Adaptor
PCIe x1
ext: for RJ45-connector, Cat 5
max.4x per system
Intel PRO/1000 PF Server Adapter
PCIe x4
ext:LC-connector
max.4x per system
2-Port Copper PCIe Adapter 1000TX
S26361-F3228-E201 ( Redwater )
Gigabit Ethernet Controller Dual 1000TX
4x
Eth. Ctrl 2x1Gbit PCIe PRO/1000PT Cu LP
Intel Pro/1000 PT dual Server Adapter
PCIe x4
ext: for RJ45-plug, Cat 5
max.4x per system
Quad Port PCIe Adapter 1000TX
S26361-F3462-E201 ( Kirkwood 2 )
Gigabit Ethernet Controller Quad 1000TX
Eth. Ctrl 4x1Gbit PCIe PRO/1000PT Cu LP
Intel Pro/1000 PT quad Server Adapter
PCIe x4
ext: for RJ45-plug, Cat 5
max.3x per system
10GbE 2-Port MMF
S26361-F3505-E201 (Green Fountain SR)
10 Gigabit Ethernet Controller dual port LC lp
Eth Ctrl 2x10Gbit PCIe x8 XF SR LC lp
Intel 10 Gigabit XF SR Dual Port Server Ad.
PCIe x8, low profile
ext:LC-connector
max. 2x per system
Released in PCIe x8 slot only!
M
Fujitsu Technology Solutions x86 PRIMERGY Serve
22 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
M
Section
IX
System Management Products (RemoteView)
S26361-F1790-E241
iRMC S2 advanced pack
integrated remote management controller
activation key for
graphical console redirection
and remote media redirection
max. 1x per system
S26361-F1790-E221
RemoteView Software V5.0
Installation and configuration of
RemoteView Web and LAN FrontEnd
BMC-Manager, RTDS and FreeDOS
Online manuals
S26361-F2557-E205
Local Service Panel incl. mount. kit
Customer Self Service
LSP module incl. mounting kit
0.5" x 5.25"
max. 1x per system
1x
S26361-F2557-E106
Local Service Display incl. mount. kit
Customer Self Service
LSD module incl. mounting kit
0.5" x 5.25"
max. 1x per system
Section
X
Miscellaneous
Section
XI
Country specific power cord
Options and other peripherals
For other options, refer to SystemArchitect and Pricelist.
These options are supplied lose with the shipment.
For suitable peripherals for this product, please refer to SystemArcitect.
Country specific power cords are not required for rack versions, except for USA&Canada.
Power cords are shipped in a rack version with inlet connector for non-heating apparatus.
Description in englisch. Both included in basic unit.
(1x with Standard PSU, 2x with hot plug upgrade)
T26139-Y1742-E10
USA, Canada
For shipments to USA&Canada, you have to order
one power cord (1,8m, grey) per power supply.
End PRIMERGY RX300 S5
Fujitsu Technology Solutions x86 PRIMERGY Serve
23 of 24
System configurator and order-information guide
PRIMERGY RX300 S5
Status 2010-07-30
Change Report
Date
Order number
Changes
2010-04-06
2009-10-01
2009-09-01
2009-09-01
2009-08-01
2009-08-01
2009-06-30
2009-06-30
2009-06-30
2009-06-30
2009-06-17
2009-03-30
S26361-F3601-E160/500
S26361-F3299-E32/64
S26361-F3554-E/L512
S26361-F4006-E*
S26361-F3324-E7
S26361-F3857-E7
S26113-F555-E10
S26361-K1237-V701
S26361-K1237-V601
S26361-K1237-V501
S26361-F2748-E633
new BC-SATA HD drives - now available
new SSD HD drives - as soon as available
New SAS Modular RAID Controller 6Gb/s - now available
New SAS HDDs 6Gb/s - now available
New Tape drive DDS 5 USB - now available
New Tape drive RDX USB - now available
New 2nd Gold PSU
New base unit with Gold PSU
New base unit with Gold PSU
New base unit with Gold PSU
New graphics card released
First release
Fujitsu Technology Solutions x86 PRIMERGY Serve
24 of 24