Cisco SFP-10G-LR network transceiver module

Data Sheet
Cisco 10GBASE SFP+ Modules
Product Overview
®
The Cisco 10GBASE SFP+ modules (Figure 1) offer customers a wide variety of 10 Gigabit Ethernet connectivity
options for data center, enterprise wiring closet, and service provider transport applications.
Figure 1.
Cisco 10GBASE SFP+ Modules
Features and Benefits
Main features of Cisco 10GBASE SFP+ modules include:
●
Smallest 10G form factor
●
Supports 10GBASE Ethernet and OTU2/OTU2e
●
Hot-swappable input/output device that plugs into an Ethernet SFP+ port of a Cisco switch
●
Provides flexibility of interface choice
●
Supports “pay-as-you-populate” model
●
Supports digital optical monitoring capability
●
Supports the Cisco quality identification (ID) feature that enables a Cisco switch to identify whether the
module is certified and tested by Cisco
●
Optical interoperability with 10GBASE XENPAK, 10GBASE X2, and 10GBASE XFP interfaces on the
same link
Cisco SFP-10G-SR
The Cisco 10GBASE-SR Module supports a link length of 26m on standard Fiber Distributed Data Interface
(FDDI)-grade multimode fiber (MMF). Using 2000MHz*km MMF (OM3), up to 300m link lengths are possible.
Using 4700MHz*km MMF (OM4), up to 400m link lengths are possible.
Cisco SFP-10G-SR-X
The Cisco SFP-10G-SR-X is a 10GBASE-SR module for extended operating temperature range. It supports a link
length of 26m on standard Fiber Distributed Data Interface (FDDI)-grade multimode fiber (MMF). Using
2000MHz*km MMF (OM3), up to 300m link lengths are possible. Using 4700MHz*km MMF (OM4), up to 400m link
lengths are possible.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 1 of 9
Cisco SFP-10G-LRM
The Cisco 10GBASE-LRM Module supports link lengths of 220m on standard Fiber Distributed Data Interface
(FDDI) grade multimode fiber (MMF). To ensure that specifications are met over FDDI-grade, OM1 and OM2
fibers, the transmitter should be coupled through a mode conditioning patch cord. No mode conditioning patch
cord is required for applications over OM3 or OM4. For additional information on mode conditioning patch cord
requirements please see: http://www.cisco.com/en/US/prod/collateral/modules/ps5455/product_bulletin_c25530836.html.
The Cisco 10GBASE-LRM Module also supports link lengths of 300m on standard single-mode fiber (SMF,
G.652).
Cisco FET-10G
The Cisco FET-10G Fabric Extender Transceiver support link lengths up to 100m on laser-optimized OM3 or OM4
multimode fiber. It is supported on fabric links only from a Nexus 2000 to a Cisco parent switch. Note this product
is not orderable individually. For more information refer to Nexus 2000 datasheet:
http://www.cisco.com/en/US/prod/collateral/switches/ps9441/ps10110/data_sheet_c78-507093.html.
Cisco SFP-10G-LR
The Cisco 10GBASE-LR Module supports a link length of 10 kilometers on standard single-mode fiber
(SMF, G.652).
Cisco SFP-10G-LR-X
The Cisco SFP-10G-LR-X is a multirate 10GBASE-LR, 10GBASE-LW and OTU2/OTU2e module for extended
operating temperature range. It supports a link length of 10 kilometers on standard single-mode fiber
(SMF, G.652).
Cisco SFP-10G-ER
The Cisco 10GBASE-ER Module supports a link length of up to 40 kilometers on standard single-mode fiber
(SMF, G.652).
Cisco SFP-10G-ZR
The Cisco SFP-10G-ZR is a multirate 10GBASE-ZR, 10GBASE-ZW and OTU2/OTU2e module. It supports link
lengths of up to about 80 kilometers on standard single-mode fiber (SMF, G.652). This interface is not specified as
part of the 10 Gigabit Ethernet standard and is instead built according to Cisco specifications.
Cisco SFP+ Twinax Copper Cables
Cisco SFP+ Copper Twinax (Figure 2) direct-attach cables are suitable for very short distances and offer a costeffective way to connect within racks and across adjacent racks. Cisco offers passive Twinax cables in lengths of
1, 1.5, 2, 2.5, 3 and 5 meters, and active Twinax cables in lengths of 7 and 10 meters.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 2 of 9
Figure 2.
Cisco Direct-Attach Twinax copper cable assembly with SFP+ connectors
Cisco SFP+ Active Optical Cables
Cisco SFP+ Active Optical Cables (Figure 3) are direct-attach fiber assemblies with SFP+ connectors. They are
suitable for very short distances and offer a cost-effective way to connect within racks and across adjacent racks.
Cisco offers Active Optical Cables in lengths of 1, 2, 3, 5, 7, and 10 meters
Figure 3.
Cisco Direct-Attach Active Optical Cables with SFP+ connectors
Technical Specifications
Platform Support
Cisco SFP+ modules are supported on Cisco switches and routers. For more details, refer to the document “Cisco
10 Gigabit Ethernet Transceiver Modules Compatibility Matrix”:
http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6974.html.
Connectors and Cabling
Connectors: Dual LC/PC connector (-SR, -LRM, -LR, -ER, -ZR and FET-10G).
Note:
Only connections with patch cords with PC or UPC connectors are supported. Patch cords with APC
connectors are not supported. All cables and cable assemblies used must be compliant with the standards
specified in the standards section.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 3 of 9
Table 1 provides cabling specifications for the Cisco SFP+ modules.
Table 1.
SFP+ Port Cabling Specifications
Cisco SFP+
Wavelength
(nm)
Cable Type
Core Size
(Microns)
Modal
Bandwidth
*
***
(MHz km)
Cable
*
Distance
Cisco SFP-10G-SR
Cisco SFP-10G-SR-X
850
MMF
62.5
160 (FDDI)
26m
62.5
200 (OM1)
33m
50.0
400
66m
50.0
500 (OM2)
82m
50.0
2000 (OM3)
300m
50.0
4700 (OM4)
400m
MMF
62.5
500
220m
SMF
50.0
400
100m
50.0
500
220m
G.652
-
300m
50.0
500 (OM2)
25m
50.0
2000 (OM3)
100m
50.0
4700 (OM4)
100m
Cisco SFP-10G-LRM
Cisco FET-10G
1310
850
MMF
Cisco SFP-10G-LR
Cisco SFP-10G-LR-X
1310
SMF
G.652
-
10km
****
1550
SMF
G.652
-
40km
Cisco SFP-H10GB-CU1M
-
Twinax cable, passive, 30AWG cable assembly
-
-
1m
Cisco SFP-H10GB-CU1-5M
-
Twinax cable, passive, 30AWG cable assembly
-
-
1.5m
Cisco SFP-H10GB-CU2M
-
Twinax cable, passive, 30AWG cable assembly
-
-
2m
Cisco SFP-H10GB-CU2-5M
-
Twinax cable, passive, 30AWG cable assembly
-
-
2.5m
Cisco SFP-H10GB-CU3M
-
Twinax cable, passive, 30AWG cable assembly
-
-
3m
Cisco SFP-H10GB-CU5M
-
Twinax cable, passive, 24AWG cable assembly
-
-
5m
Cisco SFP-H10GB-ACU7M
-
Twinax cable, active, 30 AWG cable assembly
-
-
7m
Cisco SFP-H10GB-ACU10M
-
Twinax cable, active, 28 AWG cable assembly
-
-
10m
Cisco SFP-10G-AOC1M
-
Active Optical Cable assembly
-
-
1m
Cisco SFP-10G-AOC2M
-
Active Optical Cable assembly
-
-
2m
Cisco SFP-10G-AOC3M
-
Active Optical Cable assembly
-
-
3m
Cisco SFP-10G-AOC5M
-
Active Optical Cable assembly
-
-
5m
Cisco SFP-10G-AOC7M
-
Active Optical Cable assembly
-
-
7m
Cisco SFP-10G-AOC10M
-
Active Optical Cable assembly
-
-
10m
Cisco SFP-10G-ER
**
*
Minimum cabling distance for -SR, -LRM, -LR, -ER modules is 2m, according to the IEEE 802.3ae.
Links longer than 30km are considered engineered links as per IEEE 802.3ae.
***
Specified at transmission wavelength.
****
Requires 5 dB 1550nm fixed loss attenuator for < 20km. Attenuator is available as a spare. The part number is
15216-ATT-LC-5=.
**
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 4 of 9
Table 2 shows the main optical characteristics for the Cisco SFP+ modules.
Table 2.
Optical Transmit and Receive Specifications
Product
Type
Cisco SFP-10G-SR
10GBASE-SR 850nm MMF
Transmit Power (dBm)*
Receive Power (dBm)*
Maximum
Minimum
Maximum
Minimum
Transmit and
Receive
Wavelength (nm)
**
-7.3
-1.0
-9.9
840 to 860
**
-1.2
Cisco SFP-10G-SR-X
10GBASE-SR 850nm MMF
-1.2
-7.3
-1.0
-9.9
840 to 860
Cisco SFP-10G-LRM
10GBASE-LRM 1310nm
MMF and SMF
0.5
-6.5
0.5
-8.4 (in
average) and ***
6.4 (in OMA)
1260 to 1355
Cisco FET-10G
FET-10G 850nm MMF
-1.3
-8
-1
-9.9
840 to 860
Cisco SFP-10G-LR
10GBASE-LR 1310nm SMF
0.5
-8.2
0.5
-14.4
1260 to 1355
Cisco SFP-10G-LR-X
10GBASE-LR, 10GBASELW and OTU2e 1310nm
SMF
0.5
-8.2
0.5
-14.4
1260 to 1355
Cisco SFP-10G-ER
10GBASE-ER 1550nm SMF
4.0
-4.7
-1
-15.8
1530 to 1565
*
Transmitter and receiver power is in average, unless specified.
The launch power shall be the lesser of the class 1 safety limit or the maximum receive power. Class 1 laser requirements are
defined by IEC 60825-1: 2001.
***
Both average and OMA specifications must be met simultaneously.
**
Table 3 details optical specifications for the Cisco SFP-10G-ZR modules
Table 3.
SFP-10G-ZR Optical Parameters
Parameter
Symbol
Minimum
Typical
Maximum
Units
1565
nm
Notes and Conditions
Transmitter
Transmitter wavelength
Side-mode suppression
ratio
1530
SMSR
Transmitter extinction
ratio
Transmitter optical
output power
Pout
30
dB
9
dB
0
4.0
dBm
Average power coupled into single-mode
fiber
Receiver optical input
wavelength
1260
1565
nm
Receiver Sensitivity specified over 15301565nm only, with 3dB degradation
permitted from 1260-1530nm
Receiver damage
threshold
+5
dBm
Receiver Overload
-7
dBm
Receiver
Receiver performance at 10GE LAN and 10GE WAN rates, non-FEC application
Receiver sensitivity
-24
Chromatic Dispersion
Penalty@ 1600 ps/nm
dBm
3
At BER=1E-12 with PRBS31 and 10GE
frame
dB
Receiver performance at OTU2/OTU2e rates, FEC application
Receiver sensitivity
-27
Chromatic Dispersion
Penalty@ 1300 ps/nm
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
dBm
3
At Pre-FEC BER=1E-5 for GFEC and PreFEC BER=7E-4 for EFEC with PRBS31 and
OTU2 frame
dB
Page 5 of 9
Parameters are specified over temperature and at end of life unless otherwise noted. When shorter
Note:
distances of single-mode fiber are used (<40km), an inline optical attenuator must be used to avoid overloading
and damaging the receiver.
Table 4 describes the bail latch color code for each type of optical SFP+ module.
Table 4.
SFP+ Optical Modules Color Code
Product
Bail Latch Color
Cisco SFP-10G-SR
Beige
Cisco SFP-10G-SR-X
Beige
Cisco SFP-10G-LRM
Orange
Cisco FET-10G
Brown
Cisco SFP-10G-LR
Blue
Cisco SFP-10G-LR-X
Blue
Cisco SFP-10G-ER
Red
Cisco SFP-10G-ZR
Green
Cisco SFP-H10GB-CU1M
Beige
Cisco SFP-H10GB-CU1-5M
Black
Cisco SFP-H10GB-CU2M
Brown
Cisco SFP-H10GB-CU2-5M
Yellow
Cisco SFP-H10GB-CU3M
Orange
Cisco SFP-H10GB-CU5M
Gray
Cisco SFP-H10GB-ACU7M
Blue
Cisco SFP-H10GB-ACU10M
Red
Cisco SFP-10G-AOC1M
Beige
Cisco SFP-10G-AOC2M
Brown
Cisco SFP-10G-AOC3M
Orange
Cisco SFP-10G-AOC5M
Gray
Cisco SFP-10G-AOC7M
Blue
Cisco SFP-10G-AOC10M
Red
Dimensions
Dimensions (H x W x D): 8.5 x 13.4 x 56.5mm. Cisco SFP+ connectors typically weigh 75 grams or less.
Environmental Conditions and Power Requirements
Operating temperature range:
●
Commercial temperature range (COM): 0 to 70°C (32 t o 158°F)
●
Extended temperature range (EXT): -5 to 85°C (23 to 185°F)
●
Storage temperature range: -40 to 85°C (-40 to 185° F)
Table 5 provides the maximum power consumption and operating temperature range ratings per Cisco SFP+
module.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 6 of 9
Table 5.
SFP+ Modules Maximum Power Consumption
Product
Power Consumption (W)
Operating Temperature Range
Cisco SFP-10G-SR
1
COM
Cisco SFP-10G-SR-X
1
EXT
Cisco SFP-10G-LRM
1
COM
Cisco FET-10G
1
COM
Cisco SFP-10G-LR
1
COM
Cisco SFP-10G-LR-X
1
EXT
Cisco SFP-10G-ER
1.5
COM
Cisco SFP-10G-ZR
1.5
COM
Cisco SFP-H10GB-CU1M
1
COM
Cisco SFP-H10GB-CU1-5M
1
COM
Cisco SFP-H10GB-CU2M
1
COM
Cisco SFP-H10GB-CU2-5M
1
COM
Cisco SFP-H10GB-CU3M
1
COM
Cisco SFP-H10GB-CU5M
1
COM
Cisco SFP-H10GB-ACU7M
1
COM
Cisco SFP-H10GB-ACU10M
1
COM
Cisco SFP-10G-AOC1M
1
COM
Cisco SFP-10G-AOC2M
1
COM
Cisco SFP-10G-AOC3M
1
COM
Cisco SFP-10G-AOC5M
1
COM
Cisco SFP-10G-AOC7M
1
COM
Cisco SFP-10G-AOC10M
1
COM
Warranty
●
Standard warranty: 90 days
●
Extended warranty (optional): Cisco SFP+ modules can be covered in a Cisco SMARTnet Service support
®
contract for the Cisco switch or router chassis
Ordering Information
Table 6 provides the ordering information for Cisco SFP+ modules and related cables.
Table 6.
Ordering Information
Description
Product Number
SFP+ Modules
Cisco 10GBASE-SR SFP+ Module for MMF
SFP-10G-SR
Cisco 10GBASE-SR SFP+ Module for MMF, extended temperature range
SFP-10G-SR-X
Cisco 10GBASE-LRM SFP+ Module for MMF and SMF
SFP-10G-LRM
Cisco 10GBASE-LR SFP+ Module for SMF
SFP-10G-LR
Cisco multireat 10GBASE-LR, 10GBASE-LW and OTU2e SFP+ Module for SMF, extended temperature range
SFP-10G-LR-X
Cisco 10GBASE-ER SFP+ Module for SMF
SFP-10G-ER
Cisco 10GBASE-ZR SFP+ Module for SMF
SFP-10G-ZR
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 7 of 9
Description
Product Number
SFP+ Twinax Copper Modules
10GBASE-CU SFP+ Cable 1 Meter, passive
SFP-H10GB-CU1M
10GBASE-CU SFP+ Cable 1.5 Meter, passive
SFP-H10GB-CU1-5M
10GBASE-CU SFP+ Cable 2 Meter, Passive
SFP-H10GB-CU2M
10GBASE-CU SFP+ Cable 2.5 Meter, Passive
SFP-H10GB-CU2-5M
10GBASE-CU SFP+ Cable 3 Meter, passive
SFP-H10GB-CU3M
10GBASE-CU SFP+ Cable 5 Meter, passive
SFP-H10GB-CU5M
10GBASE-CU SFP+ Cable 7 Meter, active
SFP-H10GB-ACU7M
10GBASE-CU SFP+ Cable 10 Meter, active
SFP-H10GB-ACU10M
SFP+ Active Optical Cables
10GBASE-AOC SFP+ Cable 1 Meter
SFP-10G-AOC1M
10GBASE-AOC SFP+ Cable 2 Meter
SFP-10G-AOC2M
10GBASE-AOC SFP+ Cable 3 Meter
SFP-10G-AOC3M
10GBASE-AOC SFP+ Cable 5 Meter
SFP-10G-AOC5M
10GBASE-AOC SFP+ Cable 7 Meter
SFP-10G-AOC7M
10GBASE-AOC SFP+ Cable 10 Meter
SFP-10G-AOC10M
Regulatory and Standards Compliance
Standards:
●
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
●
GR-326-CORE: Generic Requirements for Single-Mode Optical Connectors and Jumper Assemblies
●
GR-1435-CORE: Generic Requirements for Multifiber Optical Connectors
●
IEEE 802.3: 10-Gigabit Ethernet
●
ITU-T G.709: Interfaces for the Optical Transport Network
●
ITU-T G.975: GFEC
●
ITU-T G.975.1: EFEC
●
SFP+ MSA SFF-8431 (Optical Modules, Active Optical Cables, and Passive Twinax cables)
●
SFP+ MSA SFF-8461 (Active Twinax cables)
Safety:
●
Laser Class 1 21CFR-1040 LN#50 7/2001
●
Laser Class 1 IEC60825-1
●
Cable jacket of SFP+ copper modules is UL #E116441 Compliant
●
All length SFP+ copper cables are ELV and RoHS Compliant
Additional Information
For more information about Cisco 10GBASE SFP+ fiber modules or 10GBase SFP+ copper modules (twinax
cable), contact your sales representative or visit: http://www.cisco.com/en/US/products/ps6574/index.html.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 8 of 9
Printed in USA
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
C78-455693-11
07/12
Page 9 of 9