Datalogic Skorpio™ Single Cradle Ethernet
NOTE
Correct Mobile Computer Insertion/ Removal
USB Connection
For correct insertion into the cradle, insert the mobile computer from the
top of the cradle and push it down until the clip of the cradle clicks. If you
are using a Datalogic Skorpio™ model, release the backstrap from the
bottom side before inserting it into the cradle.
Be sure that the switch is in the “USB” position.
Read this manual carefully before performing any type of
connection from the terminal to a host PC using the
Datalogic Skorpio™ Single Cradle Ethernet.
The user is responsible for any damages caused by
incorrect use of the equipment or by inobservance of the
indication supplied in this manual.
Connect the single cradle Ethernet to the host by means of any USB
straight cord, such as Datalogic CAB-381 cable.
Insert the power supply plug into the power jack on the back of the cradle
and attach the power supply to a power outlet. Once the host has been
turned on, insert the Datalogic Skorpio™ mobile computer into the cradle.
A
C
Do not attempt to disassemble the Datalogic Skorpio™
Single Cradle Ethernet, as it does not contain parts that
can be repaired by the user. Any tampering will invalidate
the warranty.
B
NOTE
D
The Datalogic Skorpio™ Single Cradle Ethernet paired with a Datalogic
Skorpio™ mobile computer builds a reading system for the collection,
decoding and transmission of barcoded data.
The Datalogic Skorpio™ Single Cradle Ethernet is both a USB and an
Ethernet communication adapter between the host computer and the
Datalogic Skorpio™ mobile computer.
The Datalogic Skorpio™ Single Cradle Ethernet also functions as a
battery charger, both for the mobile computer and the spare battery pack.
The spare battery can be charged by inserting it into the slot at the back
of the cradle.
Figure 4 - USB Connection
Figure 2 - Mobile Computer Insertion
To remove the mobile computer from the cradle, simply pull it upwards
while holding the cradle firmly down.
CONNECTIONS
Key:
A)
Host computer
B)
94A051017 CAB-381 USB Type A-B straight cable
C)
Datalogic Skorpio™ Single Cradle Ethernet
D)
94ACC4595 FPS18 power supply without power cord
94ACC1150 Power cord EU 3-pin
Power supply is required for Datalogic Skorpio™ mobile computer to be
connected to the cradle and for battery recharging operations.
NOTE
Ethernet communication requires Datalogic Skorpio™ SW
version 5.411 or later. Verify the software version by
tapping on Software – Version in the Datalogic default
home page. Otherwise, search for the file version.htm
under the Windows folder.
Ethernet Connection
Be sure that the switch is in the “Ethernet” position.
Connect the Ethernet cradle (Ethernet port ) to an Ethernet hub or a port
on the host device.
Connections should always be made with power OFF!
G
H
A
CAUTION
Insert the power supply plug into the power jack on the back of the cradle
and attach the power supply to a power outlet. Once the host has been
turned on, insert the Datalogic Skorpio™ mobile computer into the cradle.
C
A
B
F
E
During switch operation from Ethernet position to USB
position and vice versa the mobile computer must not be
inserted in the cradle.
D
Figure 1 – Datalogic Skorpio™ Single Cradle Ethernet General View
Key:
A)
Contacts for Datalogic Skorpio™ Mobile computer
B)
Communication status LED
C)
Battery charge status LED
D)
Ethernet port with integrated Link and Speed LEDs
E)
USB connector
F)
Power supply connector
G)
Spare battery slot
H)
Switch Ethernet/USB
NOTE
D
B
+
Figure 5 – Ethernet Connection
Key:
Figure 3 - Power Supply Polarity
822000860
C
Each connection requires a power supply to be connected to the
cradle. We recommend the DL FPS18 power supply.
1
3.XX SW versions are later than 5.XX Sw versions
A)
Datalogic Skorpio™ Single Cradle Ethernet
B)
94ACC4595 FPS18 power supply without power cord
94ACC1150 Power cord EU 3-pin
C)
UTP CAT 5E cable (recommended use)
D)
Ethernet hub
USING THE SPARE BATTERY CHARGER
LED INDICATORS
FCC COMPLIANCE
Correctly insert the battery pack of the Datalogic Skorpio™ or of the
Datalogic Skorpio-GUN™ into the slot: simply press it into the slot until
the battery latch is automatically closed; charging starts automatically.
Communication LED Status Indicators
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Color
Figure 6
To remove the battery pack release the latch on the charger for the
Datalogic Skorpio™ and the latch on the gun battery pack for the
Datalogic Skorpio-GUN™ as indicated in figure 7:
USB MODE
Status
Red
Cradle is powered
Green
Mobile Computer inserted
Yellow
USB cable is connected
Color
ETHERNET MODE
Status
Red
Cradle is powered
Green
Mobile Computer inserted
Yellow
Link established
Yellow Blinking
Activity
Modifications or changes to this equipment without the expressed
written approval of Datalogic could void the authority to use the
equipment.
This device complies with PART 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference which may cause undesired operation.
Battery Charging LED Status Indicators
Color
Status
Off
Battery absent
Red
Battery charge in progress
Green
Charge completed
Yellow Blinking
Error
Datalogic Mobile S.r.l.
Via S. Vitalino 13
40012 - Lippo di Calderara
Bologna - Italy
08
dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el
DL-SKORPIO SINGLE CRADLE ETHERNET
TECHNICAL FEATURES
Electrical Features
Power supply *
Consumption
Charge time
Figure 7
from 12 to 14 VDC ± 5%
Max 1.6 A with mobile computer inserted
3 h 30 mins Skorpio™
5 h Skorpio-GUN™
Communication Features
Interface
Ethernet 10/100 Base T, USB 1.1 version
Physical Features
Dimensions
102 x 154 x 108 mm
4.01 x 6,06 x 4.25 in
Weight (without
462 g / 16,30 oz
connection cables)
Indicators
Bicolored Communication LED
Bicolored Battery charge status LED
Ethernet Link LED (yellow)
Ethernet Speed LED (green)
Environmental Features
Working temperature**
0° to +50°C / 32° to 122°F **
Storage temperature
-20° to +70°C / -4° to 158°F
Humidity
90% without condensation
Degree of protection
IP20
EN 60529
Electrostatic discharge
4 KV contact / 8 KV air
EN 61000-4-2
*
**
Recommended DL power supply: FPS18.
Batteries must be charged at a temperature ranging from 0° to 40 °C.
e tutti i suoi modelli
and all its models
et tous ses modèles
und seine Modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
den nachstehenden angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
89/336/EEC EMC Directive
e
and
et
und
y
92/31/EEC, 93/68/EEC
emendamenti successivi
further amendments
ses successifs amendements
späteren Abänderungen
succesivas enmiendas
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla
sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic compatibility and product
safety.
Basée sur la législation des Etats membres relative à la compatibilité électromagnétique et à la sécurité
des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit
und Produktsicherheit entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad
electromagnética y las Medidas de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con la siguientes normas:
EN 55022 ( CLASS B ITE ), SEPTEMBER 1998:
INFORMATION TECHNOLOGY EQUIPMENT
RADIO DISTURBANCE CHARACTERISTICS
LIMITS AND METHODS OF MEASUREMENTS
EN 55024, SEPTEMBER 1998:
AMENDMENT A1, OCTOBER 2001
AMENDMENT A2, JANUARY 2003
INFORMATION TECHNOLOGY EQUIPMENT
IMMUNITY CHARACTERISTICS
LIMITS AND METHODS OF MEASUREMENT
Lippo di Calderara, December 16th , 2008
Paola Chientaroli
Quality Assurance Manager