.
Ordering Guide
Cisco Aironet 1250 Series Ordering Guide
®
®
The Cisco Aironet 1250 Series is an enterprise-class 802.11n access point designed for challenging RF
environments. A dual-band rugged indoor access point, the 1250 Series provides reliable and predictable WLAN
coverage with data rates of up to 600 Mbps. With a choice of 2.4-GHz and 5-GHz radio modules, the 1250 Series
may be ordered as follows:
●
Access point platform with pre-installed radio modules: Includes the 1250 Access Point platform with preinstalled 2.4- and 5-GHz radio modules, or only a 2.4-GHz radio module. The combination of radio modules is
determined by the part number.
●
Individual components: The access point platform (no radio modules) and radio modules are separately
orderable as spares.
Pre-installed Radio Modules
Table 1 lists the part numbers for the Cisco Aironet 1250 Series access point platform with pre-installed radio
modules. Each part number corresponds to a specific combination of the Cisco Aironet 1250 Series access point
platform and one or two radio modules. Access points ordered in this manner arrive with the radio modules installed
in the access point platform. Customers are responsible for verifying approval for use in their individual countries. To
verify approval and to identify the regulatory domain that corresponds to a particular country, please visit
http://www.cisco.com/go/aironet/compliance.
Table 1.
Cisco Aironet 1250 Series with Pre-installed Radio Modules
Part Number
Description
Access Point
Platform
AIR-AP1252AG-x-K9
802.11a/g/n- 2.4/5-GHz Mod
Auto AP; 6 RP-TNC
AIR-AP1250
AIR-LAP1252AG-x-K9
Radio Modules
Regulatory Domain
AIR-RM1252A-x-K9
x=
● A = FCC
● C = China
and
802.11a/g/n- 2.4/5-GHz Unified
AP; 6 RP-TNC)
AIR-RM1252G-A-K9
● E = ETSI
● I = Middle East
● K = Korea
● N = Non-FCC
● P = Japan2
● S = Singapore
● T = Taiwan
AIR-AP1252G-x-K9
AIR-LAP1252G-x-K9
802.11g/n- 2.4 GHz
Autonomous AP; 3 RP-TNC
AIR-AP1250
802.11g/n- 2.4 GHz Unified AP;
3 RP-TNC
AIR-RM1252G-A-K9
x=
● A = FCC
● E = ETSI
● P = Japan2
Cisco Aironet 1250 Series access point platforms with pre-installed radio modules ship with the following:
●
Cisco Aironet 1250 Series access point and radio module(s)
●
Mounting hardware kit
◦
One mounting plate, two 4 x 40 x 3/16 in screws, and a mounting plate latch (all attached to the
access point)
◦
Two suspended ceiling T-rail clips, spacers (accommodates standard and recessed T-rails), and nuts
◦
Four 8 x 18 x 3/4 in pan head Phillips sheet metal screws
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 1 of 1
Ordering Guide
◦
Four #8 plastic wall anchors
◦
One 10 x 24 nut (for ground stud on the mounting plate)
◦
Two cable tie wraps
●
Product quick start guide
●
Translated safety warning document for the product
●
Cisco product registration card
An external AC power supply and power cord does not ship standard with Cisco Aironet 1250 Series Access Point.
An optional external AC power supply is available, but is required only if AC power will be used to power the access
point. The external AC power supply is not needed if the AIR-PWRINJ4 power injector is used to power the access
point; the injector has its own integrated AC power supply. Refer to the section “Power Options” for additional details.
In addition to the standard contents listed above, there are several options available in the Cisco Configuration Tool
that may be ordered in conjunction with the access point. These options are show in Table 2 below.
Table 2.
Configuration Options for the Cisco Aironet 1250 Series with Pre-installed Radio Modules
Configuration Option
2.4-GHz Antenna
Options
Selections
Description/Notes
● None*
● AIR-ANT2422DG-R
● No 2.4-GHz antenna
● Three 2.4-GHz 2.2 dBi Gray Straight Dipole Ant RP-TNC
● AIR-ANT2422DB-R
● AIR-ANT2422DW-R
● Three 2.4-GHz 2.2 dBi Black Dipole Antenna RP-TNC
● Three 2.4-GHz 2.2 dBi White Dipole Antenna RP-TNC
Note: Additional antennas are available for the AP1250 as separately
orderable spares. See the “Antennas” section below.
5-GHz Antenna Options
(Only available for part
numbers with 5 GHz
radios)
● None*
● AIR-ANT5135DG-R
● No 5-GHz antenna
● Three 5-GHz 3.5 dBi Gray Straight Dipole Ant RP-TNC
● AIR-ANT5135DB-R
● AIR-ANT5135DW-R
● Three 5-GHz 3.5 dBi Black Dipole Antenna RP-TNC
● Three 5-GHz 3.5 dBi White Dipole Antenna RP-TNC
Note: Additional antennas are available for the AP1250 as separately
orderable spares. See the “Antennas” section below.
Power Option
● AIR-PWRINJ4
● AIR-PWR-SPLY1
● Power Injector for the Cisco Aironet 1250 Series
● Power Supply for the Cisco Aironet 1250 Series
● AIR-NO-PWR-SPPLY
● Do not ship a power supply
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 2 of 6
Ordering Guide
Configuration Option
Selections
Description/Notes
● None Selected
● AIR-PWR-CORD-SW
Country Power Cord
Opts
● AIR-PWR-CORD-SA
● AIR-PWR-CORD-IS
● AIR-PWR-CORD-DM
● AIR-PWR-CORD-CH
● AIR-PWR-CORD-AP
● AIR-PWR-CORD-AR
● AIR-PWR-CORD-AU
● AIR-PWR-CORD-CE
● AIR-PWR-CORD-IT
● AIR-PWR-CORD-JP
● AIR-PWR-CORD-NA**
● AIR-PWR-CORD-UK
AIR Software Option for
AP1250
● Autonomous
● Unified (LWAPP)
Console Cable Option
● None Selected*
● AIR-CONCAB1200
● AIR Line Cord Switzerland
● AIR Line Cord South Africa
● AIR Line Cord Israel
● AIR Line Cord Denmark
● AIR Line Cord Main
● AIR Line Cord Asia Pacific
● AIR Line Cord Argentina/Uruguay
● AIR Line Cord Australia
● AIR Line Cord Central Europe
● AIR Line Cord Italy
● AIR Line Cord Japan
● AIR Line Cord North America
● AIR Line Cord United Kingdom
The software version number will vary over time as new software versions
are released.
● No console cable
● Console Cable for 1130AG, 1200, 1230AG, 1240AG, 1250 Series
* Default selection
** Default selection for all AP1250 products in the -A regulatory domain
Configurable options will ship in the same box as the access point. Additional AP1250 Series antennas and
accessories are also available and may be ordered separately as spares.
Cisco Aironet 1250 Series Eco-Pack
Cisco Aironet 1250 Series Eco-Packs ship with 5 access points and are designed to reduce product packaging and
preserve the environment (Table 3). Note that power supplies and power cords are not included with the eco-pack.
For customers who require local power, power supplies and power cords need to be ordered as separate line items.
Table 3.
Cisco Aironet 1250 Series Eco-Pack SKUs and Regulatory Domains
Part Number
Product Description
AIR-LAP1252-A-K9-5
802.11a/g/n 2.4/5 GHz Unified AP, FCC, 5 APs
AIR-LAP1252-E-K9-5
802.11a/g/n 2.4/5 GHz Unified AP, ETSI, 5 APs
AIR-LAP1252-N-K9-5
802.11a/g/n 2.4/5 GHz Unified AP, Non-FCC, 5 APs
AIR-AP1252-N-K9-5
802.11a/g/n 2.4/5 GHz Autonomous AP, Non-FCC, 5 APs
Individual Components
Table 4 lists the available spare part numbers for the Cisco Aironet 1250 Series access point platform and individual
radio modules. Spares are not configurable.
Table 4.
Cisco Aironet 1250 Series Part Numbers for Spares
Part Number
Description
Regulatory Domain
AIR-AP1250=
Autonomous AP Platform (no radio modules); Spare
Not applicable
AIR-LAP1250=
Unified AP Platform (no radio modules); Spare
Not applicable
AIR-AP1250MNTGKIT=
1250 Series Ceiling, Wall Mount Bracket kit; Spare
Not applicable
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 3 of 6
Ordering Guide
Part Number
Description
Regulatory Domain
AIR-RM1252A-x-K9=
802.11a/n 5-GHz Radio Module; 3 RP-TNC; Spare
x=
● A = FCC
● C = China
● E = ETSI
● I = Middle East
● K = Korea
● N = Non-FCC
● P = Japan2
● S = Singapore
● T = Taiwan
AIR-RM1252G-A-K9=
802.11g/n 2.4-GHz Radio Module; 3 RP-TNC; Spare
x=
● A = FCC
● E = ETSI
● P = Japan2
Regulatory Domains
Regulatory domains are used to distinguish groups of countries that adhere to the same or similar regulations for
radio usage with regards to available channels and transmit power. Cisco Aironet radio products are set at the
factory to allow a particular channel set and maximum transmit power; this is reflected in the part number as the
single character following the model number (for example, in AIR-LAP1252AG-A-K9, the regulatory domain is
represented by “-A”). Customers must select the regulatory domain that corresponds to their particular country when
ordering an Aironet 1250 with pre-installed radio modules or spare radio modules.
Cisco Aironet 1250 Series access points are certified for use in many countries around the world, but have not been
approved for use in all countries. For current worldwide approval status of Cisco Aironet 1250 Series access points,
visit http://www.cisco.com/application/pdf/en/us/guest/products/ps5861/c1650/cdccont_0900aecd80537b6a.pdf.
Note that because regulatory requirements change frequently, the version applicable for your country may have
changed from previous-generation Cisco Aironet products.
Antennas
Each radio module for the Cisco Aironet 1250 Series requires external antennas, which must be ordered as a
configurable option or separately as spares. The number of antennas each access point or radio module supports is
included in the Global Price List description (for example, 3 RP-TNC).
Table 5 contains a list of the antennas that may be used with the Cisco Aironet 1250 Series. Additional antennas are
also available as described in the Cisco Aironet 2.4-GHz and 5-GHz Antennas and Accessories Data Sheet or the
Antenna Product Portfolio for Cisco Aironet 1250 Series Access Points At-A-Glance. Note that Cisco Aironet 1250
Series Access Points are certified for operation only with Cisco Aironet antennas; to ensure regulatory compliance,
select Cisco Aironet antennas for use with Cisco 1250 Series Access Points.
Table 5.
Cisco Aironet 1250 Series Antenna Part Numbers for Spares
Frequency
Part Number
Antenna Type
Antenna Gain (dBi)
2.4GHz
AIR-ANT5959
Diversity Ceiling Omni
2
AIR-ANT2422DG-R
Grey Non-Articulating Dipole
2.2
AIR-ANT4941
Black Articulating Dipole
2.2
AIR-ANT2430V-R
Three Element Omni Antenna
3
AIR-ANT1728
Ceiling Mount Omni
5.2
AIR-ANT2506
Mast Mount Omni
5.2
AIR-ANT2452V-R
Diversity Pillar Omni
5.2
AIR-ANT2460P-R
Patch
6
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 4 of 6
Ordering Guide
Frequency
5GHz
Part Number
Antenna Type
Antenna Gain (dBi)
AIR-ANT2465P-R
Diversity Patch
6.5
AIR-ANT2485P-R
Patch
6
AIR-ANT2410Y-R
Yagi
10
AIR-ANT5135DG-R
Grey Non-Articulating Dipole
3.5
AIR-ANT5135D-R
Black Articulating Dipole
3.5
AIR-ANT5140V-R
Three Element Omni Antenna
4
AIR-ANT5145V-R
Diversity Omni-Directional
4.5
AIR-ANT5160V-R
Omni-Directional
6
For more information on antenna options, visit http://www.cisco.com/en/US/products/hw/wireless/ps469/index.html.
Power Options
The Cisco Aironet 1250 Series Access Point may be powered by a Cisco Ethernet switch, a power injector, or a local
power supply.
Caution: The Aironet 1250 Series Access Point with two RM1252 radio modules installed requires greater than the
12.95W allowed for by the 802.3af standard. Certain Cisco Ethernet switches are capable of providing this greater
amount of power and can fully power the Aironet 1250 Series Access Point with two RM1252 radio modules
installed. Refer to the Aironet 1250 Series Access Point data sheet for further details.
Caution: An external AC power supply and power cord does not ship with the Cisco Aironet 1250 Series. If one is
required, it can be configured when the access point is ordered, or ordered as a spare.
If an Ethernet switch with Power over Ethernet is not being used, the power injector or power supply must be ordered
either as a configurable option or as a spare. If ordered as a configurable option, the power injector or power supply
will ship in the same box as the access point. Power options may also be ordered separately as spares as shown in
Table 6.
Table 6.
Cisco Aironet 1250 Series Power Option Part Numbers for Spares
Part number
Product Description
AIR-PWRINJ4=
Power Injector—1250 Series; Spare
AIR-PWR-SPLY1=
Power Supply—1250 Series; Spare
The following powering options are not supported by the Aironet 1250 Series Access Point:
●
Cisco PoE (6W)
●
Cisco PoE (13W)
●
Cisco mid-span
●
AIR-PWR-A
●
PWRINJ-FIB
●
PWRINJ3
●
AIR-PWRINJ1500
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 5 of 6
Ordering Guide
Software
®
The Cisco Aironet 1250 Series can be ordered with Cisco IOS Software to operate as a standalone (autonomous)
access point or with the Lightweight Access Point Protocol (LWAPP) software to operate as part of the Cisco Unified
Wireless Network. To gain the full breadth of mobility services, the Cisco Aironet 1250 Series should be deployed
with LWAPP, requiring a connection to a WLAN controller.
Console Cable
The Cisco Aironet 1250 Series can be configured and monitored using the console port. A console cable does not
ship by default with the access point. When you order the access point with pre-installed radio modules, the console
cable is available as a configurable option. If ordered as a configurable option, the console cable will ship in the
same box as the access point. The console cable may also be ordered separately as a spare (Table 7).
Table 7.
Cisco Aironet 1250 Series Console Cable Part Number
Part Number
Product Description
AIR-CONCAB1200=
Cisco Aironet 1130AG, 1200, 1230, 1240 and 1250 Series Console Cable
Mounting Kit
The Cisco Aironet 1250 Series Access Point ships standard with a mounting bracket and hardware. A spare
mounting kit may be purchased separately (Table 8).
Table 8.
Cisco Aironet 1250 Series Mounting Bracket Part Number
Part Number
Product Description
AIR-AP1250MNTGKIT=
AP1250 Access Point Ceiling/Wall Mount Bracket Kit, spare
Printed in USA
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
C07-423376-03
09/09
Page 6 of 6