Single Phase Systems-North American PC125/PC420 Series Enclosure Power Distribution Units (ePDU™) PC125-C Front RACK MOUNTED • 19” x 3.4” (2U) x 8.5”. • Approximate shipping weight: 19 lbs. SPIKE/SURGE SUPPRESSION • L-N, L-G, N-G (3 N/O) REMOTE I/O PORTS • Remote on/off and EPO control, EPO overrides remote and local control • Sequence Power Up additional equipment down line • “LT” units only: Latching remote (N/C) EPO, momentary start LOCAL/OFF/REMOTE SWITCHING • Local: Power “on or off” to the switched outlets • Off: When breaker is “on” but this switch is in the “off” mode, you will have power to the unswitched outlets only • Remote: Power “on or off” to the switched outlets via a remote device • When using a Latching remote, the selection switch is wired for Remote/Off/Remote - There is no local control (12) NEMA OUTLETS • 4 unswitched and 8 switched via remote (4) INDICATOR LIGHTS • (1) Main breaker power “ON” • (1) Power to unswitched outlets • (2) Power to switched outlets POWER INPUT • Power cable with plug is attached to unit through the rear panel cable grip EMI/RFI FILTERING • Common Mode Line to Ground • Differential Mode Line to Line PC125-A-LT PC125-A2-LT PC125-B-LT PC125-C-LT PC125-D-LT PC125-F-LT MULTIPLE TIME DELAY(MTD)TM • Section 1 powers on immediately followed four seconds later by Section 2 • Select PC420 in part number for MTD option OVERLOAD CIRCUIT PROTECTION • Electromagnetic breaker provides manual on/off switching and trips in an overload condition SPECIFICATIONS PC125-A PC125-A2 PC125-B PC125-C PC125-D PC125-F Approvals UL UL UL UL UL UL Voltage Input/Output (50/60Hz) 120V~ 120V~ 240V~ 120V~ 120V~ 240V~ Current Input 15A 20A 15A 30A 30A 30A Current Output 12A 16A 12A 24A 24A 24A Full Load VA 1440VA 1920VA 2880VA 2880VA 2880VA 5760VA NEMA Outlets 5-15R 5-20R 6-15R 5-15R 5-20R 6-15R Circuit Breaker 15A 20A 15/15A 15/15/30A 20/20/30A 15/15/30A EMI/RFI Filter 20A 20A 20A 30A 30A 30A Multi-Stage Surge Suppression 270V/150V 270V/150V 320V/270V 270V/150V 270V/150V 320V/270V Cord/Length/Plug 14/3, 9’ 12/3, 9’ 14/3, 9’ 10/3, 15’ 10/3, 15’ 10/3, 15’ NEMA Power Input Plug 5-15P 5-20P N/A L5-30P L5-30P L6-30P Multiple Time Delay (MTD) PC420-A PC420-A2 PC420-B PC420-C PC420-D PC420-F 2 www.pulizzi.com • firstname.lastname@example.org • 800-870-2248 • Fax: 605-334-4999 © 2008 Eaton Corporation. All Rights Reserved. All specifications are subject to change without notice. Optional Remote Control Panel RCP200-BLK-LT RCP100-BLK-LT Standard Remote Control Interface REMOTE START REQUIRES (2) CONDITIONS: 1. The “on/off/remote” switch must be in the “remote” position. 2. A maintained closure between pins 1 & 3 will turn the unit on. REMOTE POWER OFF REQUIRES (1) CONDITION: 1. Opening the maintained connection between pins 1 & 3 will turn off the switched outlets. REMOTE EPO REQUIRES (1) CONDITION: 1. A maintained contact between pins 2 & 3 will turn off the switched outlets regardless of the position of the “on/off/remote” switch. SEQUENCED REMOTE: Connect pins 1, 2 & 3 of the sequence port to pins 1, 2 & 3 on any remote port of the slave unit. (Do not connect to another “sequence” port!) The sequence port of the master unit activates 4 seconds after the final set of outlets turn on. Additional units may be daisy chained in this fashion. CAUTION! THIS TYPE OF REMOTE IS NOT TO BE SUBSTITUTED FOR A SAFETY INTERLOCK! EPO is normally open, so removing the EPO connection will not shut down the power to the unit. Latching Remote “LT” Control Interface REMOTE START REQUIRES (2) CONDITIONS: 1. A maintained contact between pins 2 & 3. 2. A momentary contact between pins 1 & 3. REMOTE POWER OFF OR EPO REQUIRES (1) CONDITION: 1. Opening the maintained connection between pins 2 & 3. Additional EPO or stop buttons can be connected in series between pins 2 & 3. This will turn off the switched outlets regardless of the remote switch position. SEQUENCE REMOTE: Connect pins 1 & 2 of the “sequence” port to any remote port on another “-LT” unit. The sequence port activates 4 seconds after the final set of outlets turn on. (Do not connect to another “sequence” port!) NOTE: “LT” units are designed for remote operation only. Even when the “REMOTE/OFF/LOCAL” switch is set to “LOCAL”, the unit still requires a power request from the remote ports to turn the unit on. REMOTE OPERATION: Most Pulizzi® units have more than one remote connector. Unless labeled as “SEQUENCE” they are wired in parallel. Connection to only one remote connector is required. It is recommended that a Pulizzi® control panel be ordered for use with your PDU. Connectors are provided for those who wish to wire their own switches or control panels. We recommend using 14 AWG wire and not exceeding 50 feet for any remote cable. Mating control panels can be seen on our web site at www.pulizzi.com. If additional remote connectors are needed: The female AMP connectors used in our Power Controllers are: three pin - Part Number 1-480304-0 and four pin Part Number 1-480425-0, and are used with AMP Socket Terminals, Part Number 60619-1. The mating male AMP connector is: three pin - Part Number 1-480305-0, and four pin - Part Number 1-480426-0 and are used with AMP male contacts Part Number 60620-1. www.pulizzi.com • email@example.com • 800-870-2248 • Fax: 605-334-4999 © 2008 Eaton Corporation. All Rights Reserved. All specifications are subject to change without notice. 3 Environmental Operating Temperature is 0 to 50 C Storage Temperature is -40 to 70 C Altitude Maximum 10,000 ft. Relative Humidity is 95% Max Non-Condensing Rack Mounting Hole Specification Table 19.00” Y Z A HOLE SPECIFICATION TABLE A Y Z 3.5 .875 1.75 TVSS (Transient Voltage Surge Suppression) MOV SPECIFICATIONS Continuous AC Voltage 150VAC 270VAC 320VAC Continuous DC Voltage 200VDC 360VDC 420VDC Max. DC Leakage 200µA 200µA 200µA Low Varistor Voltage Limit 212VDC 389VDC 462VDC High Varistor Voltage Limit 243VDC 453VDC 540VDC Nominal Varistor Voltage 236VDC 424VDC 503VDC Current For Varistor Voltage 1mA 1mA 1mA Max. Clamp Voltage 8x20µs 360V 680V 810V Max. Clamp Voltage Test Current 100A 100A 100A Peak Current Rating (1 Pulse) 12000A 10000A 10000A Peak Current Rating (2 Pulse) 9000A 6500A 6500A Energy Rating (10x1000µs) 170J 325J 385J Energy Rating (8x20µs) 170J 325J 385J Capacitance 1700pF 970pF 820pF Impulse Response Time 50ns 50ns 50ns EMI/RFI FILTERING COMMON MODE INSERTION LOSS Mhz. .15 .50 1.0 5.0 10.0 30.0 dB. 6 19 28 42 45 50 DIFFERENTIAL INSERTION LOSS Mhz. .15 .50 1.0 5.0 10.0 30.0 dB. 6 6 30 50 30 30 EMI/RFI FILTERING COMMON MODE INSERTION LOSS Mhz. .1 .5 1.0 5.0 10.0 20.0 50.0 dB. 18 40 48 62 80 70 60 DIFFERENTIAL INSERTION LOSS Mhz. .1 .5 1.0 5.0 10.0 20.0 dB. 21 33 41 50 50 50 4 www.pulizzi.com • firstname.lastname@example.org • 800-870-2248 • Fax: 605-334-4999 © 2008 Eaton Corporation. All Rights Reserved. All specifications are subject to change without notice. Drawings are not shown to scale Dimensions are in inches 5 www.pulizzi.com • email@example.com • 800-870-2248 • Fax: 605-334-4999 © 2008 Eaton Corporation. All Rights Reserved. All specifications are subject to change without notice.