Data Sheet
Cisco 880 Series Integrated Services Routers
The Cisco® 880 Series Integrated Services Routers combine Internet access,
security, voice, and wireless services onto a single, secure device that is simple to
use and manage for small businesses and enterprise small branch offices and
teleworkers. The Cisco 880 Series delivers features including firewall, content filtering,
VPNs, and wireless LANs (WLANs) at broadband speeds to small offices. Easy
deployment and centralized management features enable enterprises or service
providers to deploy the Cisco 880 Series in small branch offices or small businesses.
Product Overview
Cisco 880 Series Integrated Services Routers are fixed-configuration routers that provide collaborative business
solutions for secure voice and data communication to small businesses and enterprise teleworkers. They offer
concurrent broadband services over third-generation (3G), Metro Ethernet, and multiple DSL technologies to
provide business continuity. Wireless 802.11n and 3G offer LAN and WAN mobility. The routers provide the
performance required for concurrent services, including firewall, intrusion prevention, content filtering, and
encryption for VPNs; optional 802.11g/n for mobility; and quality-of-service (QoS) features for optimizing voice and
video applications. In addition, the web-based Cisco Configuration Professional configuration tool simplifies setup
and deployment. Centralized management capabilities give network managers visibility and control of the network
configurations at the remote site.
Cisco 880 Series Integrated Services Routers offer:
●
High performance for broadband access in small offices and small branch-office and teleworker sites
●
Collaborative services with secure analog, digital voice, and data communication
●
Business continuity and WAN diversity with redundant WAN links: Fast Ethernet, Multimode
G.SHDSL(Ethernet in the First Mile [EFM] and ATM), Multimode DSL (very-high-data-rate DSL 2 [VDSL2]
and asymmetric DSL 2 and 2+ [ADSL2 and ADSL2+, respectively]), 3G, and ISDN
●
Voice-enabling features:
◦
Cisco Unified Communications Manager Express(5 user) which offers innovative key system and small
private branch exchange (PBX) capabilities for small and medium business customers
◦
Survivable Remote Site Telephony (SRST) voice continuity for enterprise small branch-office and
teleworker sites
◦
Cisco Unified Border Element (Cisco UBE) IP-IP voice gateway functions for connecting to Session
Initiation Protocol (SIP) trunking services as a replacement for Primary Rate Interface (PRI) or foreignexchange-office (FXO) voice connectivity to the service provider. Note: Cisco Unified Border Element
support for the Cisco 880 Series has feature limitations as compared to the Cisco Integrated Services
Routers Generation 2 (ISR G2 Routers). Go to http://www.cisco.com/go/cube for the full set of Cisco
Unified Border Element features. Cisco Unified Border Element limitations on Cisco 880 Routers are
listed later in this document.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 1 of 23
●
Enhanced security, including:
◦
Firewall with advance application and control for email, Instant Messaging (IM), and HTTP traffic
◦
Site-to-site remote-access and dynamic VPN services: IP Security (IPsec) VPNs (Triple Data Encryption
Standard [3DES] or Advanced Encryption Standard [AES]), Dynamic Multipoint VPN (DMVPN), Group
Encrypted Transport VPN with onboard acceleration, and Secure Sockets Layer (SSL) VPN
◦
Intrusion prevention system (IPS): An inline, deep-packet inspection feature that effectively mitigates a
wide range of network attacks
◦
Content filtering: A subscription-based integrated security solution that offers category-based reputation
rating; keyword blocking; and protection against adware, malware, spyware, and Uniform Resource
Locator (URL) blocking
●
Four-port 10/100 Fast Ethernet managed switch with VLAN support; two ports support Power over Ethernet
(PoE) for powering IP phones or external access points
●
Secure 802.11g/n access-point option based on draft 802.11n standard with support for autonomous or
Cisco Unified WLAN architectures
●
CON/AUX port for console or external modem
●
One USB 1.1 port for security eToken credentials, booting from USB, and loading configuration
●
Easy setup, deployment, and remote-management capabilities through web-based tools and Cisco IOS
®
Software
Figure 1 shows a Cisco 881 Integrated Services Router.
Figure 1.
Cisco 881 Integrated Services Router with Integrated 802.11n Access Point
Tables 1 and 2 list the routers that currently make up the Cisco 880 data, voice and SRST series, respectively.
Table 1.
Cisco 880 Series Data Models
Models
WAN Interface
LAN Interfaces
802.11g/n Option
Embedded 3G
Integrated ISDN Dial
Backup
Cisco 881
10/100-Mbps Fast
Ethernet
4-port 10/100-Mbps
managed switch
Yes (Cisco 881W)
Yes (Cisco 881G)
-
Cisco 886 VA
Multimode
VDSL2/ADSL2/2+
over ISDN
4-port 10/100-Mbps
managed switch
Yes (Cisco 886VAW)
Yes (Cisco 886VAG)
Yes
Cisco 887VA
Multimode
VDSL2/ADSL2/2+
over basic telephone
service
4-port 10/100-Mbps
managed switch
Yes (Cisco 887VAW)
Yes (Cisco 887VAG)
No
Cisco 886
ADSL2/2+ over ISDN
(Annex B)
4-port 10/100-Mbps
managed switch
Yes (Cisco 886W)
Yes (Cisco 886G)
Yes
Cisco 887
ADSL2/2+ over basic
telephone service
4-port 10/100-Mbps
managed switch
Yes (Cisco 887W)
Yes (Cisco 887G)
Yes
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 2 of 23
Models
WAN Interface
LAN Interfaces
802.11g/n Option
Embedded 3G
Integrated ISDN Dial
Backup
(Annex A)
Cisco 887V
VDSL2 over basic
telephone service
4-port 10/100-Mbps
managed switch
Yes (Cisco 887V)
Yes (Cisco 887VG)
Yes
Cisco 888
G.SHDSL (ATM)
4-port 10/100-Mbps
managed switch
Yes (Cisco 888W)
Yes (Cisco 888G)
Yes
Cisco 888E
G.SHDSL (EFM)
4-port 10/100-Mbps
managed switch
Yes (Cisco 888W)
Yes (Cisco 888EG)
Yes
Cisco 888EA
Multimode G.SHDSL
(EFM/ATM)
4-port 10/100-Mbps
managed switch
No
No
No
Table 2.
Cisco 880 Series Voice Models
Models
WAN Interface
LAN Interfaces
Voice Ports
802.11g/n Option
Cisco881V
10/100-Mbps Fast
Ethernet
4-port 10/100 Mbps managed
switch
4 foreign-exchange-station (FXS)
ports, 2 Basic Rate Interface(BRI)
ports and 1 foreign-exchange-office
(FXO) port for public-switchedtelephone-network (PSTN) fallback
No
Cisco887VA-V
Multi-mode
VDSL2/ADSL2/2+ over
POTS
4-port 10/100 Mbps managed
switch
4 foreign-exchange-station (FXS)
ports and 2 Basic Rate Interface(BRI)
ports
Yes (Cisco887VA-VW-K9)
Cisco 881 SRST
10/100-Mbps Fast
Ethernet
4-port 10-/100-Mbps managed
switch
4 foreign-exchange-station (FXS)
ports and 1 FXO port for publicswitched-telephone-network (PSTN)
fallback
Yes (Cisco 881
SRSTW)
Cisco 888 SRST
G.SHDSL
4-port 10-/100-Mbps managed
switch
4 FXS ports and 1 Basic Rate
Interface (BRI) port for PSTN fallback
Yes (Cisco 888
SRSTW)
Cisco 881 with
Cisco Unified
Border Element
10/100-Mbps Fast
Ethernet
4-port 10-/100-Mbps managed
switch
No
No
Cisco 886VA with
Cisco Unified
Border Element
Multimode
VDSL2/ADSL2/2+ over
ISDN
4-port 10-/100-Mbps managed
switch
No
No
Cisco 887VA with
Cisco Unified
Border Element
Multimode
4-port 10-/100-Mbps managed
VDSL2/ADSL2/2+ over switch
basic telephone service
No
No
Cisco 888E with
Cisco Unified
Border Element
G.SHDSL (EFM)
4-port 10-/100-Mbps managed
switch
No
No
Cisco 888 with
Cisco Unified
Border Element
G.SHDSL (ATM)
4-port 10-/100-Mbps managed
switch
No
No
The Cisco 880 Series is ideal for small branch offices and teleworkers who need to be connected to larger
enterprise networks as well as small businesses for either voice or data applications. These routers help extend
corporate networks to secure remote sites while giving users access to the same applications found in a corporate
office. When users require WLAN access, visibility and control of network security are even more critical at the
remote site. The Cisco 880 Series meets this need with a single device that combines integrated 802.11g/n
capabilities with security features such as Wi-Fi Protected Access (WPA), including authentication with IEEE
802.1x with Cisco Extensible Authentication Protocol (LEAP) and Protected EAP (PEAP) and encryption with WPA
Temporal Key Integrity Protocol (TKIP). (Refer to the wireless solution overview and security data sheet for more
information. The Cisco 880 Series models that include the integrated access point can use either autonomous or
Cisco Unified WLAN modes. In Cisco Unified WLAN mode, as part of an enterprise WLAN architecture, all WLAN
functions are centrally managed through Cisco Wireless LAN Controllers and the Cisco Wireless Control System
(WCS).
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 3 of 23
Service providers and value-added resellers can take advantage of the Cisco 880 Series to provide a true
business-class broadband service. Business customers are using broadband access to connect to the Internet or
to connect offices together, and they require a platform that incorporates voice and security without sacrificing
performance. The Cisco 881V and Cisco 887VA-V voice routers offer industry-leading voice gateway capability
with the ability to layer of Cisco Unified Communications Manager Express or SRST as required. Many of these
customers are connecting computers in offices through WLANs; having a single device for both WAN and WLAN
access provides a new option for managed services. These customers also require a higher level of support to
keep their networks operational. Services with these customers should be simple to set up, while allowing a level
of remote management and troubleshooting to quickly address support inquiries. The Cisco 880 Series meets the
requirements of small offices and managed services providers.
Figure 2 shows deployment scenarios.
Figure 2.
Deployment Scenarios
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 4 of 23
Applications
The Cisco 880 Series is ideally suited for deployment in a small office or in a small office that is part of a large
network, most often with a secure VPN connection. These types of offices can include the following:
●
Small remote office: The Cisco 880 Series can connect users in a small remote office, such as an
insurance, lawyer, or sales office. When connecting to the main office, VPN encryption and integrated
security such as firewall and intrusion prevention protect the network at the perimeter. The Cisco 880 with
the Cisco Unified Border Element Series can also support connection to SIP trunking voice-over-IP (VoIP)
services provided by the service provider. Additionally, IT managers can centrally manage the remote site
to quickly troubleshoot any network problems. For added reliability, customers can also use the integrated
3G or ISDN backup or connect through an external modem if the primary broadband link fails. Integrated
secure unified WLAN connectivity simplifies the deployment and management devices at the remote site.
Redundant WAN links offer business continuity, enabling nondisruptive business operation.
●
Virtual office: The Cisco 880 Series is ideal for corporate teleworkers who have a mix of broadband
connection types such as DSL, 3G, and Metro Ethernet. The Cisco 880 Voice gateway and SRST Series
provides a secure virtual office with all the collaborative services such as data, voice, and fax services.
SRST helps ensure voice services are operational in case of WAN link failure, and redundant WAN links
help ensure business continuity. QoS features in the Cisco 880 Series allow for connection of an IP or
analog phone to the router, giving voice traffic precedence over data applications. Integrated WLAN
support in the Cisco 880 Series helps ensure that if wireless connectivity is used it is secure. (Refer to the
Cisco Virtual Office Solution, http://www.cisco.com/go/cvo, for more information.)
●
Remote call-center agent: Similar to teleworking applications, this solution extends the Cisco IP Contact
Center solution for telephone call-center agents to remote sites. With a high-quality, secure connection
through the Cisco 880 Series, call-center agents can be dispersed away from costly call-center facilities
while maintaining secure and productive voice and data access in their homes. SRST and businesscontinuity solutions in the Cisco 880 Series provide reliability and continuous business operation.
Alternatively, the remote call-center agent can be provided with SIP trunking service with service
demarcation provided by Cisco Unified Border Element features and the central call center can forward
calls to the remote call-center agent through the remote-office SIP trunk.
●
Retail VPN: Retail stores migrating from dialup connections for point-of-sale transactions can use the Cisco
880 Series to take advantage of low-cost broadband access with the required security to comply with
payment-card-industry (PCI) and other data security requirements. They can then add multiple devices and
applications to the store network to take advantage of the increased bandwidth and also incorporate
optional WLAN support to enable secure mobility and enhance productivity.
●
Managed services: Service providers and value-added resellers can use the Cisco 880 Series as a
platform to offer differentiated business-class security, voice, and WLAN services for small business
customers. With built-in analog and digital voice ports and the ability to upgrade to a 5 user Cisco Unified
Communications Manager Express IP PBX, service providers can now offer all the Unified communications
benefits to small and medium businesses. The SIP trunking connectivity features of the Cisco 880 with
Cisco Unified Border Element Series Router can provide the high-quality VoIP service needed through the
service provider cloud.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 5 of 23
Features and Benefits
Table 3 lists the features and benefits of the Cisco 880 Series Integrated Services Routers.
Table 3.
Features and Benefits of Cisco 880 Series Routers
Feature
Benefit
Increased performance to run
concurrent services
● Cisco 880 Series Router performance allows customers to take advantage of broadband network
speeds while running secure, concurrent data, voice, video, and wireless services.
Enhanced security
● An integrated stateful and application inspection firewall provides network perimeter security.
● High-speed IPsec 3DES and AES encryption offers data privacy over the Internet.
● Intrusion prevention enforces security policy in a larger enterprise or service provider network.
● Content filtering offers category-based URL classification and blocking, thus providing increased
productivity and better use of company resources.
WAN diversity
● Multiple WAN links include Fast Ethernet, multimode VDSL2/ADSL2/2+, multimode G.SHDSL, 3G,
and ISDN.
Redundant WAN links
● Redundant WAN links provide business continuity and WAN diversity with.
Four-port 10-/100-Mbps managed
switch
● The Cisco 880 Series allows for connection of multiple devices in a small office, with the ability to
designate a port as the network edge.
● An optional external PoE adapter powers IP phones and external access points to avoid individual
power supplies or power injectors.
● VLANs allow for secure segmentation of network resources.
CON/AUX port
● A single dual-purpose port provides direct connection to a console or external modem for
management or backup access points.
Optional 802.11g/n access point
● This broadband router offers a secure integrated access point in a single device.
● This integrated Wi-Fi access point offers IEEE 802.11n 2.0 standard support for mobile access to
high-bandwidth data, voice, and video applications through the use of multiple-input, multiple-output
(MIMO) technology that provides increased throughput, reliability, and predictability.
● The Cisco 880 Series supports both autonomous and unified modes.
Real-time clock
● A built-in real-time clock maintains an accurate date and time for applications that require an
accurate time stamp, such as logging and digital certificates.
Voice Gateway (supported on 881V
and 887VA-V voice models)
● Provides voice gateway functionality with the ability to upgrade to a 5 user Cisco Unified
Communications Manager Express or 5 user SRST)
SRST (supported on SRST voice
models)
● SRST provides business continuity for voice when the WAN link fails by switching calls to the
PSTN.
Cisco Unified Border Element
(supported on Cisco Unified Border
Element voice models)
● Support for SIP trunk connectivity, including demarcation and interworking, is based on a Cisco
Unified Border Element feature license.
● Transcoding of media is not supported on the Cisco 880 Series Cisco Unified Border Element
feature set.
Cisco Configuration Professional
● Cisco Configuration Professional uses smart wizards and task-based tutorials, which resellers and
customers can use to quickly and easily deploy, configure, and monitor a Cisco access router
without requiring knowledge of the Cisco IOS Software command-line interface (CLI).
Unified wireless management
● Configuration and management of access points is automated and simplified without manual
intervention.
● A unified hybrid remote-edge access point (HREAP) provides the following:
◦
WLAN services to remote and branch offices without deploying a WLAN controller at each
location
◦
Central configuration and control of unified WLAN services for remote offices through a WAN link
◦
Flexibility in setting up wireless access at remote locations by specifying how traffic is to be
bridged or tunneled
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 6 of 23
Summary
Cisco 880 Series Integrated Services Routers combine increased network performance with advanced security to
allow small-office customers to get the most from their broadband connections for both data and voice
applications. With models supporting different broadband technologies such as DSL, 3G, and Metro Ethernet, the
Cisco 880 Series can be deployed at any small-office location. Optional integrated 802.11g/n wireless capabilities
provide true business-class WAN and WLAN access in a single solution. With the Cisco 880 Series, enterprise IT
managers and service providers can take advantage of a solution that can be easily set up at the remote site and
can be centrally managed to reduce ongoing operational costs.
Product Specifications
Cisco IOS Software Support
Table 4 lists the minimum Cisco IOS Software releases and the default Cisco IOS Software feature sets.
Table 4.
Cisco IOS Software Releases and Default Cisco IOS Software Feature Sets
Models
Universal Image
Default Feature Set
First Cisco IOS Software
Release
Cisco 881
Data
Advanced Security
12.4(20)T
Cisco 881 SEC, Embedded 3G
Data
Advanced IP
12.4(20)T, 15.1(4)M
Cisco 881V
Voice
Advanced IP
*
15.1(4)M
*
12.4(20)T
Cisco 881 SRST
Voice
Advanced IP
Cisco 886VA and 887VA
Data
Advanced Security
15.1(2)T
Cisco 886VA and 887VA WLAN
Data
Advanced Security
15.1(3)T
Cisco 886VA and 887VA
Embedded 3G
Data
Advanced Security
15.1(4)M
Cisco 886 and 887
Data
Advanced Security
12.4(22)YB3
Cisco 886 and 887 SEC, 3G
Data
Advanced IP
12.4(22)YB3
Cisco 887V
Data
Advanced Security
12.4(22)YB, 12.4(24)T
Cisco 887V SEC, 3G
Data
Advanced IP
12.4(22)YB, 12.4(24)T
Cisco 887V WLAN
Data
Advanced Security
15.0(1)M
Cisco 887V 3G
Data
Advanced IP
15.0(1)M
Cisco 887VA-V
Voice
Advanced IP
15.1(4)M
Cisco 887VA-V-W
Voice
Advanced IP
15.1(4)M
Cisco 888
Data
Advanced Security
12.4(20)T
Cisco 888 SEC, 3G
Data
Advanced IP
12.4(20)T, 15.1(4)M
*
Cisco 888 SRST
Voice
Advanced IP
Cisco 888E
Data
Advanced Security
12.4(20)T
15.1(1)T
Cisco 888E Embedded 3G
Data
Advanced IP
15.1(4)M
Cisco 888EA
Data
Advanced Security
15.2(2)T
Cisco 881, 886VA, 887VA, 888,
888E with Cisco Unified Border
Element
Voice
Advanced IP
15.1(4)M
Access-point software (ap801)
-
-
12.4(10b)JA3
*
Cisco 881V, 887VA-V, 881 SRST and 888 SRST run the Cisco 880 voice universal image, which shares the same data and
security features as the Advanced IP feature sets of Cisco 880 data models.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 7 of 23
Tables 5 and 6 list software features of the Cisco 880 Series.
Table 5.
Cisco IOS Software Features on Cisco 880 Series: Advanced Security Feature Set (Default)
Feature
IP and IP services features
Description
● Routing Information Protocol Versions 1 and 2 (RIPv1 and RIPv2)
● Generic routing encapsulation (GRE) and Multipoint GRE (MGRE)
● Cisco Express Forwarding
● Standard 802.1d Spanning Tree Protocol
● Layer 2 Tunneling Protocol (L2TP)
● Network Address Translation (NAT)
● Dynamic Host Configuration Protocol (DHCP) server, relay, and client
● Dynamic Domain Name System (DNS)
● DNS Proxy
● DNS Spoofing
● Access control lists (ACLs)
ATM features (ADSL and G.SHDSL
ATM models only)
● ATM Variable Bit Rate real-time (VBR-rt)
● ATM Unspecified Bit Rate (UBR), Constant Bit Rate (CBR), and Variable Bit Rate non-realtime
(VBR-nrt)
● ATM operations, administration, and maintenance (OA&M) support for F5 Continuity Check;
segment and end-to-end loopback; and Integrated Local Management Interface (ILMI) support
● TX ring adjustment
● Virtual-circuit (VC) bundling
● Per-VC queuing
● Per-VC traffic shaping
● 10 ATM virtual circuits on the 886, 887, and 888 models
● 4 ATM virtual circuits on the 886VA and 887VA models
● RFCs 1483 and 2684
● Point-to-Point Protocol over ATM (PPPoA)
● PPP over Ethernet (PPPoE)
Switch features
● Auto Media Device In/Media Device Cross-Over (medium dependent interface (MDI)/MDI crossover
(MDX)
● Eight 802.1Q VLANs
● MAC filtering
● Two-port 802.3af and Cisco compliant PoE
● Switched Port Analyzer (SPAN)
● Storm Control
● Smartports
Security features
Secure connectivity:
● SSL VPN for secure remote access
● Hardware-accelerated DES, 3DES, AES 128, AES 192, and AES 256
● Public-key-infrastructure (PKI) support
● 20 IPsec tunnels
● Cisco Easy VPN Client and Server
● NAT transparency
Zone-based policy firewall:
● Stateful inspection transparent firewall
● Advanced application inspection and control
● Secure HTTP (HTTPS), FTP, and Telnet authentication proxy
● Dynamic and static port security
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 8 of 23
Feature
Description
● Low-Latency Queuing (LLQ)
● Weighted Fair Queuing (WFQ)
QoS features
● Class-Based WFQ (CBWFQ)
● Class-Based Traffic Shaping (CBTS) (on Fast Ethernet WAN ports and DSL ports in Packet
Transport Mode [PTM] only)
● Class-Based Traffic Policing (CBTP)
● Policy-Based Routing (PBR)
● Class-Based QoS MIB
● Class of service (CoS)-to-differentiated services code point (DSCP) mapping
Management features
● Cisco Configuration Professional
● Cisco Configuration Express
● Cisco Configuration Engine support
● Cisco AutoInstall
● IP service-level agreement (SLA)
● Cisco IOS Embedded Event Manager (EEM)
● CiscoWorks
● Cisco Security Manager
● Telnet, Simple Network Management Protocol Version 3 (SNMPv3), Secure Shell (SSH) Protocol,
CLI, and HTTP management
● RADIUS and TACACS+
● Out-of-band management with ISDN S/T port or external modem through virtual auxiliary port
● Cisco WCS for management of unified access points in models supporting WLAN
High-availability features
● Virtual Router Redundancy Protocol (VRRP) (RFC 2338)
● Hot Standby Router Protocol (HSRP)
● Multigroup HSRP (MHSRP)
● Dial backup with external modem through virtual auxiliary port
● Dial backup with ISDN S/T port (select DSL models only)
● 3G backup (3G models only)
Number of recommended users
Table 6.
20
Cisco IOS Software Features on Cisco 880 Series: WLAN Features (Available with Wireless Option)
Feature
WLAN hardware
Description
● IEEE 802.11n draft 2.0 standards-based access point with 802.11 b/g compatibility
● Automatic rate selection for 802.11g/n
● Captive omnidirectional 2-dBi gain dipole antennas
● 2 x 3 MIMO radio operation
● Removable antennas on Cisco 881W models
● Wi-Fi 802.11n Draft v2.0 certified
WLAN software features
● Autonomous or unified access point
● Cisco WCS support for monitoring of autonomous-mode access points
● Option to maximize throughput or maximize range
● Software-configurable transmit power
● Radio roles, including access point, root bridge, nonroot bridge, and workgroup bridge
● Wi-Fi Multimedia (WMM) certification
● Traffic specifications (TSPEC) Call Admission Control (CAC) to ensure voice quality is maintained
● Unscheduled Automatic Power Save Delivery (UPSD) to reduce latency
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 9 of 23
Feature
Description
● Standard 802.11i
● WPA and AES (WPA2)
WLAN security features
● EAP authentication: Cisco LEAP, PEAP, Extensible Authentication Protocol Transport Layer
Security (EAP TLS), Extensible Authentication Protocol-Flexible Authentication via Secure
Tunneling (EAP-FAST), Extensible Authentication Protocol-Subscriber Information Module
(EAP-SIM), Extensible Authentication Protocol-Message Digest Algorithm 5 (EAP-MD5), and
Extensible Authentication Protocol-Tunneled TLS (EAP-TTLS)
● Static and dynamic Wired Equivalent Privacy (WEP)
● Temporal Key Integrity Protocol/Simple Security Network (TKIP/SSN) encryption
● MAC authentication and filter
● User database for survivable local authentication using LEAP and EAP-FAST
● Configurable limit to the number of wireless clients
● Configurable RADIUS accounting for wireless clients
● Pre-shared keys (PSKs) (WPA-small office or home office [WPA-SOHO])
Certifications
Service set identifiers (SSIDs)
16
Wireless VLANs
8
Encrypted wireless VLANs
8
Multiple broadcast service set
identifiers (MBSSIDs)
16
Cisco IOS Software Advanced IP Services Feature Set (Optional Software Upgrade)
The Advanced IP Services software image has all the features of the Advanced Security software image with the
addition of the features listed in Tables 7 through 10.
Table 7.
Cisco IOS Software Features on Cisco 880 Series: Advanced IP Services Feature Set (Optional Software
Upgrade)
Feature
IP and IP services features
Description
● IPv4 and IPv6 Multicast
● Open Shortest Path First (OSPF)
● Border Gateway Protocol (BGP)
● Enhanced Interior Gateway Routing Protocol (EIGRP)
● Virtual Route Forwarding (VRF) Lite
● Next Hop Resolution Protocol (NHRP)
● Layer 2 Tunneling Protocol Version 3 (L2TPv3)
● Bidirectional Forwarding Detection (BFD)
● Web Cache Communication Protocol (WCCP)
Switch features
Security features
● Internet Group Management Protocol Version 3 (IGMPv3) snooping
● 802.1x
Secure connectivity:
● DMVPN
● Tunnel-less Group Encrypted Transport VPN
● IPsec stateful failover
● VRF-aware IPsec
● IPsec over IPv6
● Adaptive control technology
● SIP application layer gateway
Cisco IOS Firewall:
● Firewall stateful failover
● VRF-aware firewall
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 10 of 23
Feature
Description
Content Filtering:
● Subscription-based content filtering with Trend Micro
● Support for Websense and SmartFilter
● Cisco IOS Software black and white lists
Integrated threat control:
● IPS
● Control Plane Policing
● Flexible Packet Matching
● Network foundation protection
● Class-Based Weighted Random Early Detection (CBWRED)
● Network-Based Application Recognition (NBAR)
QoS features
● Link fragmentation and interleaving (LFI)
● Resource Reservation Protocol (RSVP)
● Real-Time Transport Protocol (RTP) header compression (cRTP)
● Differentiated Services (DiffServ)
● QoS preclassify and prefragmentation
● Hierarchical QoS (HQoS)
Metro Ethernet features
● Ethernet Operations, Administration, and Maintenance (Ethernet OAM)
● Ethernet Local Management Interface (Ethernet LMI)
● Hierarchical QoS (HQoS)
● IPv6 addressing architecture
● IPv6 name resolution
IPv6 features
● IPv6 statistics
● IPv6 translation: Transport packets between IPv6-only and IPv4-only endpoints (NAT-PT)
● Internet Control Message Protocol Version 6 (ICMPv6)
● IPv6 DHCP
Unified WLAN management
Unified access-point features:
● Supported by wireless LAN controller and Cisco WCS
● Configurable local or central switching for HREAP mode
● Radio management through Cisco WCS
● Transparent roaming with Mobility Groups
Table 8.
Cisco IOS Software Features on Cisco 880V Series: Advanced IP Services Feature Set
Feature
Description
Cisco Voice Gateway
4 FXS ports and 2 Basic Rate Interface (BRI) port for PBX connectivity. 1 FXO port is available on the
Cisco881V SKU
Cisco UCME/SRST version
Ability to upgrade to 5 user license of CME/SRST - version 8.6 and later are supported
Call-control signaling
H.323 Versions 1, 2, 3, and 4, Media Gateway Control Protocol (MGCP) 0.1 and 1.0, Skinny Client
Control Protocol (SCCP), and SIP call-control protocols are supported.
ITU standard voice codecs
G.711, G.729, G.729a/b, G.723.1, G.726, and G.728, which are standards-based compression
technologies allowing transmission of voice across IP, are supported. The G.711 standard employs 64kbps pulse code modulation (PCM) using either mu-law or a-law. Other codecs employ lower bit rates.
Cisco Unified Communications
Manager support
For SRST features for IP phones, refer to the SRST data sheet at:
http://www.cisco.com/en/US/products/sw/voicesw/ps2169/products_data_sheets_list.html.
Cisco Unified Communications Manager support for analog and digital ports come with Releases
7.1(5), 8.5(1), and 8.6(2)
Telephony interface signaling support
Cisco 880 V supports the following signaling protocols:
● FXS loop-start and ground-start signaling
● FXO
● Inbound signaling (such as dual-tone multifrequency [DTMF] and multifrequency support)
● BRI QSIG
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 11 of 23
Feature
Description
Voice features
● Echo cancellation: This feature cancels echo on tail circuits up to 64 msec (configurable tail length).
● Silence suppression and voice activity detection (VAD): Bandwidth is used only when someone is
speaking. During silent periods of a phone call, bandwidth is available for data traffic.
● Comfort-noise generation: This feature reassures the phone user that the connection is being
maintained, even when no voice packets are being transmitted.
● Caller ID support: Per-port caller ID (with per-call unblocking) is configurable over analog FXS.
● Dial-plan mapping: This feature simplifies configuration and management through automatic
mapping of dialed phone numbers to IP addresses.
Voice port-specific features
● FXS: FXS provides battery polarity reversal detection and initiation for disconnect supervision and
far-end answer supervision.
● ISDN BRI network side and phantom power: The BRI port provides the ability to connect a private
branch exchange (PBX) or private automatic branch exchange (PABX) configured as user side
directly to the router. It also provides phantom power to accommodate equipment that requires it.
● LED indicators show voice-processing resources and port status.
Fax and modem
● Fax and modem pass-through allows fax and modem traffic to pass through a voice port.
● Fax Relay provides a more robust protocol for fax transmission over packet networks. It also
supports the T.37 and T.38 fax protocols.
High-performance flexible digitalsignal-processor (DSP) architecture
● Channel capacity: Cisco 880 V supports up to four voice channels.
● Flexible DSP architecture: There is no need to specify codec complexity at configuration.
An appropriate codec is dynamically selected when a call is established, while allocating DSP
resources optimally.
● Feature upgrades: The DSP architecture allows for addition of new features through simple code
updates.
Table 9.
Cisco IOS Software Features on Cisco 880 SRST Series: Advanced IP Services Feature Set
Feature
Description
Cisco SRST version
SRST 7.0 and later are supported.
Call-control signaling
H.323 Versions 1, 2, 3, and 4, Media Gateway Control Protocol (MGCP) 0.1 and 1.0, Skinny Client
Control Protocol (SCCP), and SIP call-control protocols are supported.
ITU standard voice codecs
G.711, G.729, G.729a/b, G.723.1, G.726, and G.728, which are standards-based compression
technologies allowing transmission of voice across IP, are supported. The G.711 standard employs 64kbps pulse code modulation (PCM) using either mu-law or a-law. Other codecs employ lower bit rates.
Cisco Unified Communications
Manager support
For SRST features for IP phones, refer to the SRST data sheet at:
http://www.cisco.com/en/US/products/sw/voicesw/ps2169/products_data_sheets_list.html.
Cisco Unified Communications Manager support for analog and digital ports comes with Releases
6.1(3), 7.0(2), and 7.1(3).
Telephony interface signaling support
Cisco 880 SRST supports the following signaling protocols:
● FXS loop-start and ground-start signaling
● FXO
● Inbound signaling (such as dual-tone multifrequency [DTMF] and multifrequency support)
● BRI QSIG
Voice features
● Echo cancellation: This feature cancels echo on tail circuits up to 64 msec (configurable tail length).
● Silence suppression and voice activity detection (VAD): Bandwidth is used only when someone is
speaking. During silent periods of a phone call, bandwidth is available for data traffic.
● Comfort-noise generation: This feature reassures the phone user that the connection is being
maintained, even when no voice packets are being transmitted.
● Caller ID support: Per-port caller ID (with per-call unblocking) is configurable over analog FXS.
● Dial-plan mapping: This feature simplifies configuration and management through automatic
mapping of dialed phone numbers to IP addresses.
Voice port-specific features
● FXS: FXS provides battery polarity reversal detection and initiation for disconnect supervision and
far-end answer supervision.
● ISDN BRI network side and phantom power: The BRI port provides the ability to connect a private
branch exchange (PBX) or private automatic branch exchange (PABX) configured as user side
directly to the router. It also provides phantom power to accommodate equipment that requires it.
● LED indicators show voice-processing resources and port status.
Fax and modem
● Fax and modem pass-through allows fax and modem traffic to pass through a voice port.
● Fax Relay provides a more robust protocol for fax transmission over packet networks. It also
supports the T.37 and T.38 fax protocols.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 12 of 23
Feature
Description
High-performance flexible digitalsignal-processor (DSP) architecture
Table 10.
● Channel capacity: Cisco 880 SRST supports up to four voice channels.
● Flexible DSP architecture: There is no need to specify codec complexity at configuration.
An appropriate codec is dynamically selected when a call is established, while allocating DSP
resources optimally.
● Feature upgrades: The DSP architecture allows for addition of new features through simple code
updates.
Cisco IOS Software Features on Cisco 880 Series with Cisco Unified Border Element: Advanced IP Services
Feature Set
Feature
Description
Cisco Unified Border Element version
Cisco Unified Border Element 7.0 and later are supported.
Call-control signaling
H.323 Versions 1, 2, 3, and 4, MGCP 0.1 and 1.0, SCCP, and SIP call-control protocols are supported.
ITU standard voice codecs
G.711, G.729, G.729a/b, G.723.1, G.726, and G.728, which are standards-based compression
technologies that allow transmission of voice across IP, are supported. The G.711 standard employs
64-kbps pulse code modulation (PCM) using either mu-law or a-law. Other codecs employ lower bit
rates.
Cisco Unified Communications
Manager support
For SRST features for IP phones, refer to the SRST data sheet at:
http://www.cisco.com/en/US/products/sw/voicesw/ps2169/products_data_sheets_list.html.
Cisco Unified Communications Manager support for analog and digital ports comes with Releases
6.1(3), 7.0(2), and 7.1(3).
Telephony interface signaling support
Cisco 880 SRST supports the following PSTN trunk signaling protocols:
● FXS loop-start and ground-start signaling
● FXO
● Inbound signaling (such as dual-tone multifrequency [DTMF] and multifrequency support)
● BRI QSIG
Cisco 880 Cisco Unified Border Element supports the following VoIP trunk signaling protocols:
● Up to 15 SIP-to-SIP sessions. (no H.323 support)
Note: The Cisco 880 with Cisco Unified Border Element does not include DSP feature support such as
transcoding or transrating.
Note: The Cisco 880 with Cisco Unified Border Element does not support concurrent operation of
SRST or Cisco Unified Communications Manager Express.
Voice features
● Echo cancellation: This feature cancels echo on tail circuits up to 64 msec (configurable tail length).
● Silence suppression and VAD: Bandwidth is used only when someone is speaking. During silent
periods of a phone call, bandwidth is available for data traffic.
● Comfort-noise generation: This feature reassures the phone user that the connection is being
maintained, even when no voice packets are being transmitted.
● Caller ID support: Per-port caller ID (with per-call unblocking) is configurable over analog FXS.
● Dial-plan mapping: This feature simplifies configuration and management through automatic
mapping of dialed phone numbers to IP addresses.
Voice port-specific features
● FXS: FXS provides battery polarity reversal detection and initiation for disconnect supervision and
far-end answer supervision.
● ISDN BRI network side and phantom power: The BRI port provides the ability to connect a PBX or
PABX configured as user side directly to the router. It also provides phantom power to
accommodate equipment that requires it.
● LED indicators show voice-processing resources and port status.
System Specifications
Tables 11 and 12 list the system specifications for the Cisco 880 Series Routers.
Table 11.
System Specifications
Feature
Description
Default DRAM
● 256 MB on Cisco 880 Series data models
● 512 MB on Cisco 880 Series WLAN, embedded 3G wireless WAN (WWAN), Voice and
SRST/Cisco Unified Border Element models
Maximum DRAM
● 768 MB on Cisco 880 Series data, voice and Cisco Unified Border Element models
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 13 of 23
Feature
Description
● 1024 MB on Cisco 880 Series WLAN
Default and maximum flash memory
● 128 MB on Cisco 880 Series data, embedded 3G WWAN, and Cisco Unified Border Element
models
● 256 MB on Cisco 880 Series Voice and SRST models
WAN
● Fast Ethernet
● Multimode VDSL2 and ADSl2/2+ over ISDN with ISDN backup
● Multimode VDSL2 and ADSl2/2+ over basic telephone service
● ADSL2/2+ over ISDN with ISDN backup
● ADSL2/2+ over basic telephone service with ISDN backup
● VDSL2 over basic telephone service with ISDN backup
● Multimode G.SHDSL (2- and 4-wire support) with ISDN backup
● Fast Ethernet and 3G WAN for Code Division Multiple Access (CDMA) and high-speed downlink
packet access (HSDPA)
LAN switch
Managed 4-port 10/100BASE-T with autosensing MDI/MDX for auto crossover
Standard 802.11g/n access point based Optional on all models
on IEEE 802.11n draft 2.0 standard
Console or auxiliary port
One USB 1.1 port for advanced
security features such as security
tokens or USB flash memory
RJ-45
● One USB 1.1 port on Cisco 880 Series Routers
● USB devices supported:
◦
USB eTokens
◦
USB flash memory
Note: The USB 1.1 port cannot be used for connecting external devices other than those specified at:
http://www.cisco.com/en/US/prod/collateral/modules/ps6247/product_data_sheet0900aecd80232473.ht
ml.
ISDN BRI S/T
Available on:
● Cisco 886, 886VA, 887, 887V, 888, and 888EA for out-of-band management and dial backup or
primary
3G express card modem
Available on:
● Cisco 881G, 886G, 887G, 887VG, and 888G for out-of-band management and backup or primary
● Cisco 888G for out-of-band management and backup or primary
Note: Cisco 887VG currently ships with HSPA modem only.
External power supply
Universal 100 to 240 VAC input; 60W, 12 VDC output
Physical dimensions and weight
Product dimensions, nonwireless models (H x W x D):
● 1.9 x 12.8 x 9.8 in. (48 x 325 x 249 mm) (includes rubber feet)
● 1.75 x 12.8 x 9.8 in. (44 x 325 x 249 mm) (without rubber feet)
Product dimensions, wireless models (H x W x D):
● 1.9 x 12.8 x 10.4 in. (48 x 325 x 264 mm) (includes rubber feet)
● 1.75 x 12.8 x 10.4 in. (44 x 325 x 264 mm) (without rubber feet; excludes antennas)
● Weight: 5.5 lb (2.5 kg) maximum
Power
Product power specifications:
● AC input voltage: 100 to 240 VAC
● Frequency: 50 to 60 Hz
● Maximum output power: 60W
● Output voltages: 12 VDC
Optional internal PoE with external adapter:
● Maximum output power: 80W
● External output voltage: 48 VDC
Approvals and compliance
Emissions:
● 47 CFR Part 15: 2006
● CISPR22: 2005
● EN300386: V1.3.3: 2005
● EN55022: 2006
● EN61000-3-2: 2000 [Inc amd 1 and 2]
● EN61000-3-3: 1995 [+ amd 1: 2001]
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 14 of 23
Feature
Description
● ICES-003 Issue 4: 2004
● KN 22: 2005
● VCCI: V-3/2006.04
Immunity:
● CISPR24: 1997 [+ amd 1 and 2]
● EN300386: V1.3.3: 2005
● EN50082-1: 1992
● EN50082-1: 1997
● EN55024: 1998 [+ amd 1 and 2]
● EN61000-6-1: 2001
The following are supported on teleworker models:
● AS/NRZ 3548: 1992 Class B
● CFR 47 Part 15 Class B
● EN60555-2 Class B
● EN55022 Class B
● ICES-003, Issue 2, Class B, April 1997S
Certifications
Environmental operating range
● Nonoperating temperature: -4 to 149°F (-20 to 65°C)
● Nonoperating humidity: 5 to 95% relative humidity (noncondensing)
● Nonoperating altitude: 0 to 15,000 ft (0 to 4570m)
● Operating temperature
◦
At sea level: 32 to 104°F (0 to 40°C)
◦
Up 10,000 ft: 32 to 77°F (0 to 25°C)
◦
Derating 2.7°F/10000 ft (1.5°C/1000 ft)
● Operating humidity: 10 to 85% relative humidity (noncondensing)
● Operating altitude: 0 to 10,000 ft (0 to 3000m)
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 15 of 23
Table 12.
Wireless LAN and 3G Specifications
SRST Specifications
SRST specifications
● Packet fax and voice DSP module PVDM2-16
FXS voice-port specifications:
● Tip and ring interfaces for each FXS port (subscriber line interface card [SLIC])
● Ring voltage
● Ring frequency
● Ring waveform
● Ring load
● Ringer Equivalence Number (REN)
● Loop resistance
● On- and off-hook characteristics
● On-hook voltage (tip and ring)
● Off-hook current
● RJ-11 FXS port terminating impedance option
BRI voice-port specifications:
● Interface type
● Compliance
● Safety conformance
● ITU compliance
● Interface
● ISDN digital access
● Physical connector
● Phantom power
Wireless Specifications
Radio frequency band
● 2.4 GHz
Data rates supported
● 802.11b: 1, 2, 5.5, 6, 9, and 11 Mbps
● 802.11g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbps
● 802.11n: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54, and m0-m15
Maximum transmit power (2-channel
aggregate)
Note: Maximum power setting is subject to changes by channel and by region, depending on
regulations.
● 802.11b 20 dBm
● 802.11g 17 dBm
● 802.11n 16 dBm
3G specifications
Data rates
● CDMA: 850 and 1900 MHz
● HSDPA: 850, 900, 1900, and 2100 MHz
DSL Specifications
Tables 13 through 21 list the DSL features specifications and DSL access multiplexer (DSLAM) interoperability
support for the Cisco 880 Series Routers. For more information and details about DSLAM and line-card
interoperability, please refer to the following document: What Is Cisco ISR and ISR G2 xDSL Interoperability?
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 16 of 23
Table 13.
DSL Features Specifications
DSL Specifications
Multimode DSL (VDSL2 and ADSL2/2+)
(886VA and 887VA models)
● Broadcom Chipset
● Dying gasp
● IEEE 802.1q VLAN tagging
● Independent DSL firmware loading
VDSL2
● ITU G.993.2 (VDSL2)
● 997 and 998 band plans
● VDSL2 profiles: 8a, 8b, 8c, 8d, 12a, 12b, and 17a
● U0 band support (25-276 kHz)
● Ethernet PTM mode only based on IEEE 802.3ah 64/65 octet encapsulation
● DELT Diagnostics Mode
ADSL2/2+
● ADSL over basic telephone service with Annex A and Annex B ITU G. 992.1 (ADSL),
G.992.3 (ADSL2), and G.992.5 (ADSL2+)
● ADSL over basic telephone service with Annex M (extended upstream bandwidth) G.992.3
(ADSL2) and G.992.5 (ADSL2+)
◦
Cisco 887VA-M is optimized for PSD Mask EU-64 M9.
◦
Cisco 887VA-M supports UK Annex M.
● G.994.1 ITU G.hs
● Reach-extended ADSL2 (G.922.3) Annex L for increased performance on loop lengths
greater than 16,000 feet from central office
● T1.413 ANSI ADSL DMT issue 2 compliance
● DSL Forum TR-067 conformity
● Inpulse Noise Protection (INP) and extended INP
● Downstream Power Back-Off (DPBO)
● ATM mode only
ADSL specifications
(886 and 887 models)
● ST-Microelectronics 20190 Chipset
● ADSL over basic telephone service with Annex A and Annex B ITU G. 992.1 (ADSL),
G.992.3 (ADSL2), and G.992.5 (ADSL2+)
● ADSL over basic telephone service with Annex M (extended upstream bandwidth) G.992.3
(ADSL2) and G.992.5 (ADSL2+)
◦
Cisco 887-M is optimized for PSD Mask EU-64 M9
◦
Cisco 887M supports UK Annex M only with Huawei 5300 DSLAM and its EADB line
card with customer-premises-equipment (CPE) firmware Version 4.0.17
● G.994.1 ITU G.hs
● Reach-extended ADSL2 (G.922.3) Annex L for increased performance on loop lengths
greater than 16,000 feet from central office
● T1.413 ANSI ADSL DMT issue 2 compliance
● DSL Forum TR-067 conformity
● Does not provide interoperability with carrierless amplitude modulation/phase modulation
(CAP)-based ADSL lines
● Dying gasp
● IEEE 802.1q VLAN tagging with Cisco IOS Software Release 15.1(1)T or later
VDSL2 specifications
(887V models)
● Broadcom Chipset
● ITU G.993.2 (VDSL2) over basic telephone service only
● 997 and 998 band plans, over basic telephone service only
● VDSL2 profiles supported: 8a, 8b, 8c, 8d, 12a, 12b, and 17a
● U0 band support (25276 kHz)
● Ethernet PTM mode only based on IEEE 802.3ah 64/65 octet encapsulation
● DELT Diagnostics Mode
● IEEE 802.1q VLAN tagging
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 17 of 23
DSL Specifications
G.SHDSL (ATM mode) specifications (Cisco 888)
● Conexant/Ikanos Chipset
● 2- and 4-wire modes
● Symmetrical WAN speeds up to 2.304 Mbps over a single copper pair and up to 4.608
Mbps over two copper pairs using ITU-T G.991.2 Annex A and Annex B
● Wetting current (Section A.5.3.3 of G.991.2)
● Dying gasp; uses power status bit (Section 7.1.2.5.3 of G.991.2) for signaling
G.SHDSL (EFM mode) specifications
(Cisco 888E)
● Conexant/Ikanos Chipset
● 2-wire mode
● Symmetrical WAN speeds up to 2.304 Mbps over a single copper pair using ITU-T
G.991.2 Annex A and Annex B
● Symmetrical WAN speeds from 768 kbps to 5.696 Mbps over a single copper pair using
ITU-T G.991.2 Annex F and Annex G
● Symmetrical WAN speeds up to 22.784 Mbps over four copper pairs using IEEE 802.3ah
EFM bonding
● Wetting current (Section A.5.3.3 of G.991.2)
● Dying gasp; uses power status bit (Section 7.1.2.5.3 of G.991.2) for signaling
● Rate adaption
Multimode G.SHDSL (EFM/ATM) specifications
(Cisco 888EA)
● Lantiq Chipset
● 4-pair support
● Compliance with standard based on ITU Recommendation G.991.2
● Support for G.SHDSL Annexes A (U.S. signaling) and B (European signaling)
● Support for Annexes F and G
● Symmetrical WAN speeds up to 1 x 2304 kbps over single copper pair, up to 2 x 2304
kbps over two copper pairs, up to 3 x 2304 kbps over three copper pairs, and up to 4 x
2304 kbps over four copper pairs using ITU-T G.991.2 Annexes A and B
● Symmetrical WAN speeds up to 1 x 5696 kbps over single copper pair, up to 2 x 5696
kbps over two copper pairs, up to 3 x 5696 kbps over three copper pairs, and up to 4 x
56964 kbps over four copper pairs using ITU-T G.991.2 Annexes F and G
● Support for EFM bonding; supports up to four SHDSL pairs bonding
● In ATM mode, support for maximum of 8 permanent virtual circuits (PVCs)
● Support for dying gasp and wetting current
● Support for point-to-point configuration
● Support for 802.1Q, QinQ, trunk, and VLAN tagging
● Support for ATM CoS and IP QoS features, 802.1P, and DSCP
● Support for EFM (IEEE 802.3ah) OA&M
● Ability to configure multiple G.SHDSL EFM EHWICs per Cisco 1921, 1941, 2900, and
3900 Series Routers
● Compliance with single RJ-45 connector system requirements
Table 14.
Multimode DSL DSLAM Interoperability for Cisco 887VA
DSLAM
VDSL2 over Basic Telephone Service Line-Card Chipset
ZTE 9806
Broadcom
Huawei MA5600
Broadcom
Table 15.
Multimode DSL DSLAM Interoperability for Cisco 886VA
Siemens HIX 5300
Infineon
ECI 480
Infineon
Alcatel ASAM 7300
Globespan
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 18 of 23
Table 16.
ADSL-over-ISDN DSLAM Interoperability for Cisco 886
DSLAM
ADSL2/2+ over ISDN Line-Card Chipset
Siemens HIX 5300
Infineon
ECI 480
Infineon
Alcatel ASAM 7300
Globespan
Table 17.
ADSL over Basic Telephone Service DSLAM Interoperability for Cisco 887 and 887M
DSLAM
ADSL2/2+ over Basic Telephone Service Line-Card Chipset
Alcatel ASAM 7300
Broadcom (Annex A and Annex M)
ECI 480
Infineon (Annex A and Annex M)
Ericsson
Broadcom (Annex A and M)
Huawei 5600
Globespan (Annex A only)
Lucent Stinger
Globespan (Annex A and Annex M)
Table 18.
VDSL2 DSLAM Interoperability for Cisco 887V
DSLAM
VDSL2 over Basic Telephone Service Line-Card Chipset
ZTE 9806
Broadcom
Huawei MA5600
Broadcom
Table 19.
G.SHDSL DSLAM Interoperability for Cisco 888
DSLAM
G.SHDSL (2- and 4-Wire) Line-Card Chipset
ECI Hi-Focus SAM 480
Infineon
Alcatel ASAM7300
Conexant/Ikanos
Lucent Stinger
Conexant/Ikanos
Siemens Hix-5300
Infineon
Table 20.
G.SHDSL DSLAM Interoperability for Cisco 888E
DSLAM
G.SHDSL (2- and 4-Wire) Line-Card Chipset
Huawei 5603
Infineon
Alcatel ISAM 7302
Infineon
Hatteras HN4000e
Infineon
Table 21.
Multimode G.SHDSL DSLAM Interoperability for Cisco 888EA-K9
DSLAM
G.SHDSL (4-Pair) Line-Card Chipset
Huawei 5603
Infineon
Alcatel ISAM 7302
Infineon
Hatteras HN4000e
Infineon
Alcatel ASAM 7300
Lucent Stringer
ECI 480
Alcaltel ISAM_7330_FTTN
Actelis ML698
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 19 of 23
Ordering Information
Table 22 lists ordering information for the Cisco 880 Series. To place an order, visit the Cisco ordering homepage.
Table 22.
Ordering Information
Part Number
Product Name
Ethernet
CISCO881-K9
Cisco 881 Ethernet Security Router
C881-CUBE-K9
Cisco 881 Ethernet Security Router with integrated CUBE Licenses
CISCO881-SEC-K9
Cisco 881 Ethernet Security Router with Advanced IP Services
CISCO881W-GN-A-K9
Cisco 881 Ethernet Security Router with 802.11n FCC Compliant
CISCO881W-GN-E-K9
Cisco 881 Ethernet Security Router with 802.11n ETSI Compliant
CISCO881W-GN-P-K9
Cisco 881 Ethernet Security Router with 802.11n Japan Compliant
Ethernet and 3G
CISCO881G-K9
Cisco 881 Ethernet Security Router with 3G
CISCO881GW-GN-A-K9
Cisco 881 Ethernet Security Router with 3G, 802.11n FCC Compliant
CISCO881GW-GN-E-K9
Cisco 881 Ethernet Security Router with 3G, 802.11n ETSI Compliant
CISCO881G-S-K9
Cisco 881G Ethernet Security Router with 3G Sprint
CISCO881G-V-K9
Cisco 881G Ethernet Security Router with 3G Verizon
CISCO881G-A-K9
Cisco 881G Ethernet Security Router with 3G GSM North America
C881G-U-K9
Secure Router with WAN FE and Embedded 3.5G HSPA with SMS/GPS
C881G-S-K9
Secure Router with WAN FE and Embedded 3G EVDO Rev A with SMS/GPS for Sprint Networks
C881G-V-K9
Secure Router with WAN FE and Embedded 3G EVDO Rev A with SMS/GPS for Verizon Wireless
Networks
C881G-B-K9
Secure Router with WAN FE and Embedded 3G EVDO Rev A with SMS/GPS for BSNL Networks
C881G+7-K9
Secure Router with WAN FE and Embedded 3.7G HSPA+ Release 7 with SMS/GPS
C881G+7-A-K9
Secure Router with WAN FE and Embedded 3.7G HSPA+ Release 7 with SMS/GPS for AT&T Networks
Multi-mode DSL (VDSL2 and ADSl2/2+)
CISCO886VA-K9
Cisco 886VA router with VDSL2/ADSL2+ over ISDN
CISCO886VA-SEC-K9
Cisco 886VA Secure router with VDSL2/ADSL2+ over ISDN
C886VA-CUBE-K9
Cisco 886VA Secure router with VDSL2/ADSL2+ over ISDN and integrated CUBE licenses
CISCO887VA-K9
Cisco 887VA router with VDSL2/ADSL2+ over POTS
CISCO887VA-SEC-K9
Cisco 887VA Secure router with VDSL2/ADSL2+ over POTS
CISCO887VA-M-K9
Cisco 887VA Annex M router
C887VA-CUBE-K9
Cisco 887VA router with VDSL2/ADSL2+ over ISDN and integrated CUBE licenses
Multi-mode DSL (VDSL2 and ADSl2/2+) with WLAN
C886VA-W-E-K9
Cisco 886VA router with VDSL2/ADSL2+ over ISDN with 802.11n ETSI Compliant
C887VA-W-A-K9
Cisco 887VA router with VDSL2/ADSL2+ over POTS with 802.11n FCC Compliant
C887VA-W-E-K9
Cisco 887VA router with VDSL2/ADSL2+ over POTS with 802.11n ETSI Compliant
C887VAM-W-E-K9
Cisco 887VA Annex M router with 802.11n ETSI Compliant
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 20 of 23
Part Number
Product Name
Multi-mode DSL (VDSL2 and ADSl2/2+) with Embedded 3G
C886VAG+7-K9
Secure Router with VDSL2/ADSL2+ over ISDN and Embedded 3.7G HSPA+ Release 7 with SMS/GPS
C887VAG-S-K9
Secure Router with VDSL2/ADSL2+ over POTS and Embedded 3G EVDO Rev A with SMS/GPS for Sprint
Networks
C887VAG+7-K9
Secure Router with VDSL2/ADSL2+ over POTS and Embedded 3.7G HSPA+ Release 7 with GPS
C887VAMG+7-K9
Secure Router with Raiders VDSL2/ADSL2+ over POTS (Annex M) and Embedded 3.7G HSPA+ Release 7
with GPS
ADSL2/2+
CISCO886-K9
Cisco 886 ADSL2/2+ Annex B Router
CISCO886-SEC-K9
Cisco 886 ADSL2/2+ Annex B Security Router with Advanced IP Services
CISCO886W-GN-E-K9
Cisco 886 ADSL2/2+ Annex B Router with 802.11n ETSI Compliant
CISCO887-K9
Cisco 887 ADSL2/2+ Annex A Router
CISCO887-SEC-K9
Cisco 887 ADSL2/2+ Annex A Security Router with Advanced IP Services
CISCO887W-GN-A-K9
Cisco 887 ADSL2/2+ Annex A Router with 802.11n FCC Compliant
CISCO887W-GN-E-K9
Cisco 887 ADSL2/2+ Annex A Router with 802.11n ETSI Compliant
CISCO887M-K9
Cisco 887 ADSL2/2+ Annex M Router
CISCO887MW-GN-E-K9
Cisco 887 ADSL2/2+ Annex M Router with 802.11n ETSI Compliant
ADSL2/2+ and 3G
CISCO886G-K9
Cisco 886 ADSL2/2+ Annex B Router with 3G
CISCO886GW-GN-E-K9
Cisco 886 ADSL2/2+ Annex B Router with 3G, 802.11n ETSI Compliant
CISCO887G-K9
Cisco 887 ADSL2/2+ Annex A Router with 3G
CISCO887GW-GN-A-K9
Cisco 887 ADSL2/2+ Annex A Router with 3G, 802.11n FCC Compliant
CISCO887GW-GN-E-K9
Cisco 887 ADSL2/2+ Annex A Router with 3G, 802.11n ETSI Compliant
VDSL2
CISCO887V-K9
Cisco 887 VDSL2 over POTS Router
CISCO887V-SEC-K9
Cisco 887 VDSL2 over POTS Security Router with Advanced IP Services
CISCO887VW-GNA-K9
Cisco 887V VDSL2 Router with 802.11n FCC Compliant
CISCO887VW-GNE-K9
Cisco 887V VDSL2 Router with 802.11n ETSI Compliant
VDSL2 and 3G
CISCO887VG-K9
Cisco 887V VDSL2 Router with 3G
CISCO887VGW-GNA-K9
Cisco 887V VDSL2 Router with 3G, 802.11n FCC Compliant
CISCO887VGW-GNE-K9
Cisco 887V VDSL2 Router with 3G, 802.11n ETSI Compliant
G.SHDSL (ATM)
CISCO888-K9
Cisco 888 G.SHDSL Router
C888-CUBE-K9
Cisco 888 G.SHDSL Router with integrated CUBE licenses
CISCO888-SEC-K9
Cisco888 G.SHDSL Security Router with Adv IP Services
CISCO888W-GN-A-K9
Cisco 888 G.SHDSL Router with 802.11n FCC Compliant
CISCO888W-GN-E-K9
Cisco 888 G.SHDSL Router with 802.11n ETSI Compliant
G.SHDSL (EFM)
CISCO888E-K9
Cisco 888E G.SHDSL Router with 802.3ah EFM Support
CISCO888EW-GN-A-K9
Cisco 888E G.SHDSL Router with 802.11n FCC Compliant and 802.3ah EFM Support
CISCO888EW-GN-E-K9
Cisco 888E G.SHDSL Router with 802.11n ETSI Compliant and 802.3ah EFM Support
C888E-CUBE-K9
Cisco 888E G.SHDSL Router with 802.3ah EFM Support and integrated CUBE licenses
Multimode G.SHDSL (EFM/ATM)
C888EA-K9
Cisco Multimode 888EA G.SHDSL (EFM/ATM) Router with 802.3 ah EFM Support
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 21 of 23
Part Number
Product Name
G.SHDSL (ATM) and 3G
CISCO888G-K9
Cisco 888 G.SHDSL Router with 3G
CISCO888GW-G-NA-K9
Cisco 888 G.SHDSL Router with 3G, 802.11n FCC Compliant
CISCO888GW-G-NE-K9
Cisco 888 G.SHDSL Router with 3G, 802.11n ETSI Compliant
G.SHDSL (EFM) and 3G
C888EG+7-K9
Secure Router with Ethernet over G.SHDSL (EFM) and Embedded 3.7G HSPA+ Release 7 with SMS/GPS
Voice Gateway
C887VA-V-K9
Cisco887, V/ADSL2 WAN, 4 FXS, 2BRI, 1ISDN
C887VA-V-W-E-K9
Cisco887, V/ADSL2, 4 FXS, 2BRI, 1ISDN, 2.4GHz
C881-V-K9
Cisco881, FE WAN, 4 FXS, 2BRI, 1FXO
SRST
C881SRST-K9
Cisco 881 SRST Ethernet Security Router with FXS, FXO
C881SRSTW-GN-A-K9
Cisco 881 SRST Ethernet Security Router with FXS, FXO; 802.11n FCC Compliant
C881SRSTW-GN-E-K9
Cisco 881 SRST Ethernet Security Router with FXS, FXO; 802.11n ETSI Compliant
C888SRST-K9
Cisco 888 SRST G.SHDSL Router with FXS, BRI
C888SRSTW-GN-A-K9
Cisco 888 SRST G.SHDSL Router with FXS, BRI; 802.11n FCC Compliant
C888SRSTW-GN-E-K9
Cisco 888 SRST G.SHDSL Router with FXS, BRI; 802.11n ETSI Compliant
Teleworker
C881W-GN-A-K9
Cisco 881 Ethernet Security Router with 802.11n FCC Compliant
C881W-GN-E-K9
Cisco 881 Ethernet Security Router with 802.11n ETSI Compliant
C881W-GN-P-K9
Cisco 881 Ethernet Security Router with 802.11n Japan Compliant
POE
800-IL-PM=2
2 port 802.3af capable inline power module for 880 routers
DRAM
MEM8XX-256U512D
256-MB DRAM upgrade to 512 MB for Cisco 880 Series Routers
MEM8XX-256U768D
512-MB DRAM upgrade to 768 MB for Cisco 880 Series Routers
MEM8XX-512U768D
512-MB DRAM upgrade to 768 MB for Cisco 880 Series Routers
3G Modem
PCEX-3G-CDMA-V
Cisco 3G EVDO Rev A/0/1xRTT Modem-Verizon Networks
PCEX-3G-CDMA-S
Cisco 3G EVDO Rev A/0/1xRTT Modem-Sprint Networks
PCEX-3G-CDMA-B
Cisco 3G EVDO Rev A/0/1xRTT Modem-BSNL Networks
PCEX-3G-HSPA-US
Cisco 3.5G HSPA/UMTS/EDGE/GPRS Modem-AT&T Network Only
PCEX-3G-HSPA-G
Cisco 3.5G HSPA/UMTS/EDGE/GPRS Modem-Global Networks (Global SKU, excluding USA)
Cisco IOS Universal Software for Cisco 880
*
Cisco 880 Series IOS UNIVERSAL DATA
*
Cisco 880 Series IOS UNIVERSAL VOICE
S880DUDK9
S880VUDK9
Software License for Cisco 880 Data
SL-880-ADSEC (default)
Cisco 880 Advanced Security Image Feature License
SL-880-AIS (upgrade option)
Cisco 880 Advanced IP Services Image Feature License
SL-880-ADVSEC-NPE
Cisco 880 Advanced Security NPE License PAK (Paper)
SL-880-AIS-NPE (upgrade option)
Cisco 880 Advanced IP Services NPE License PAK (Paper)
Software License for Cisco 880 Data (Bulk)
L-SL-800-SEC-K9
Advanced IP e-Delivery PAK for Cisco 800 Series
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 22 of 23
Part Number
Product Name
Software License for Cisco 880 SRST and CUBE
SL-SRST880-AIS (included by
default)
Cisco 880 Advanced IP Services Image Feature License
SL-880-AIS and SL-880-ADVSEC
(included by default)
Cisco 880 Advanced IP Services and Security Image Feature License for 3G, Embedded 3G and CUBE
models
Security Services
SL-CNFIL-88x-1Y
One year subscription to Content Filtering for Cisco 881/888-URL/Phishing
SL-CNFIL-8xx-TRI
30 day free trial license for 88x series
SSL
FL-WEBVPN-10-K9
Feature License SSL VPN for Up to 10 Users (incremental), for 12.4T based IOS releases only
FL-SSLVPN10-K9
Feature License SSL VPN for Up to 10 Users (incremental), for 15.x based IOS releases only
Router Software
C880data-universalk9-mz
Universal image for Cisco 880 ISR Data Router Series
C880voice-universalk9-mz
Universal image for Cisco 880 SRST and CUBE Router Series
Access Point Software
*
ap801-k9w7-tar
Autonomous software image for ap801
ap801-rcvk9w8-tar
LWAPP recovery image for ap801
Each software part number has the Cisco IOS Software release number at the end of the string. For example, the part number
of IOS 12.4(20)T data universal image for Cisco 880 series is S880DUK9-12420T.
Cisco License Manager is a secure client- and server-based application used to manage Cisco IOS Software
activation and licenses. For more information about Cisco License Manager, visit http://www.cisco.com/go/clm.
Cisco Services for the Branch Office
Services from Cisco and our certified partners can help you reduce the cost and complexity of branch-office
deployments. We have the depth and breadth of experience across technologies to architect a blueprint for a
branch-office solution to meet your company's needs. Planning and design services align technology with
business goals and can increase the accuracy, speed, and efficiency of deployment. Technical services help
maintain operational health, strengthen software application functions, solve performance problems, and lower
expenses. Optimization services are designed to continually improve performance and help your team succeed
with new technologies. For more information, please visit http://www.cisco.com/go/services.
Printed in USA
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
C78-459542-15
03/12
Page 23 of 23